NISSAN TEANA 2014 Service Manual

DAS-168
< WIRING DIAGRAM >[BSW]
DRIVER ASSISTANCE SYSTEMS
ABOIA0116GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
DRIVER ASSISTANCE SYSTEMSDAS-169
< WIRING DIAGRAM > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
AAOIA0042GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-170
< WIRING DIAGRAM >[BSW]
DRIVER ASSISTANCE SYSTEMS
ABOIA0117GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
DRIVER ASSISTANCE SYSTEMSDAS-171
< WIRING DIAGRAM > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
ABOIA0118GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-172
< WIRING DIAGRAM >[BSW]
DRIVER ASSISTANCE SYSTEMS
ABOIA0119GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
DRIVER ASSISTANCE SYSTEMSDAS-173
< WIRING DIAGRAM > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
ABOIA0120GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-174
< WIRING DIAGRAM >[BSW]
DRIVER ASSISTANCE SYSTEMS
ABOIA0121GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
DIAGNOSIS AND REPAIR WORK FLOWDAS-175
< BASIC INSPECTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work FlowINFOID:0000000009464818
OVERALL SEQUENCE
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the customer to obtain information about sym ptoms using “Diagnostic Work Sheet”. (Refer to DAS-
176, "Diagnostic Work Sheet".)
JSOIA0499GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-176
< BASIC INSPECTION >[BSW]
DIAGNOSIS AND REPAIR WORK FLOW
>> GO TO 2.
2.SELF-DIAGNOSIS WITH CONSULT
1. Perform “All DTC Reading” with CONSULT.
2. Check if the DTC is detected on the self-diagnosis results of “AVM”.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 3.
3.PRE-INSPECTION FOR DIAGNOSIS
Perform pre-inspection for diagnosis. Refer to DAS-178, "Inspection Procedure"
.
>> GO TO 4.
4.ACTION TEST
Perform BSW system action test to check the operation status. Refer to DAS-179, "Description"
.
>> GO TO 6.
5.TROUBLE DIAGNOSIS BY DTC
Perform trouble diagnosis for the detected DTC. Specify a malfunctioning part. Refer to DAS-164, "DTC Index"
(ITS CONTROL UNIT).
>> GO TO 7.
6.SYMPTOM DIAGNOSIS
Perform symptom diagnosis. Specify malfunctioning part. Refer to DAS-212, "Symptom Table"
.
>> GO TO 7.
7.MALFUNCTION PART REPAIR
Repair or replace the identified malfunctioning parts.
>> GO TO 8.
8.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT)
Perform self-diagnosis with CONSULT. Check that any DTC is not detected. Erase DTC if DTC is detected
before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 9.
9.REPAIR CHECK (ACTION TEST)
Perform BSW system action test. Al so check the system operation.
Does it operate normally?
YES >> Inspection End.
NO >> GO TO 4.
Diagnostic Work SheetINFOID:0000000009464819
DESCRIPTION
In general, each customer feels differently about an inci dent. It is important to fully understand the symptoms
or conditions for a customer complaint.
There are many operating conditions that lead to the malfunction. A good grasp of such conditions can make
troubleshooting faster and more accurate.
Some conditions may cause the lane departure warning lamp to stay ON.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
DIAGNOSIS AND REPAIR WORK FLOWDAS-177
< BASIC INSPECTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
Utilize a work sheet sample to organize all of the information for troubleshooting.
KEY POINTS• WHAT..... System and functions
• WHEN..... Date, Frequencies
• WHERE..... Road conditions
• HOW..... Operating conditions, Symptoms
WORK SHEET SAMPLE
ALOIA0193GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM