NISSAN X-TRAIL 2001 Service Repair Manual

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-31
C
D
E
F
G
H
I
J
L
MA
B
LT
TKWA0066E

LT-32
PARKING, LICENSE PLATE AND TAIL LAMPS
Bulb Replacement
EKS003C1
PARKING AND TAIL LAMPS
Refer to LT-42, "REAR COMBINATION LAMP" .
LICENSE PLATE LAMP
1. Remove lens of license plate lamp.
2. Turn bulb socket, then remove it.
Removal and Installation EKS003C2
PARKING AND TAIL LAMPS
Refer toLT- 4 2 , "REAR COMBINATION LAMP"
LICENSE PLATE LAMP
Removal
1. Remove the license lamp finisher. Refer to EI-22, "LICENSE
LAMP FINISHER" in “EXTERIOR & INTERIOR (EI)” section.
2. Remove the harness from installation pawl for harness.
3. Remove license plate lamp mounting screws (2 each, RH and
LH).
4. Pull out license plate lamp from licence lamp finisher.
Installation
●Install license plate lamp in the reverse order of removal, observing the tightening torque shown below.
License plate lamp mounting screwsLicense plate lamp : 12 V 5 W
SKIA4169E
Tightening torque :1.0 - 1.8 N-m (0.10 - 0.19 kg-m,9-
16 in-lb)

FRONT FOG LAMP
LT-33
C
D
E
F
G
H
I
J
L
MA
B
LT
FRONT FOG LAMP PFP:00011
System Description EKS003DF
DESCRIPTION
Power is supplied at all times to fog lamp relay terminal 3
●through 15A fuse (No. 42, located in the fuse and fusible link box).
With the lighting switch in the 2ND position and LOW (“B”) position, power is supplied
●through 10A fuse (No. 31, located in the fuse and fusible link box).
●to lighting switch terminal 11
●through terminal 12 of the lighting switch
●to fog lamp switch terminal 32
●through terminal 31 of the fog lamp switch
●to fog lamp relay terminal 2.
FOG LAMP OPERATION
The fog lamp switch is built into the combination switch. The lighting switch must be in the 1st or 2nd position
for fog lamp operation.
With the fog lamp switch in the ON position, ground is supplied
●to fog lamp relay terminal 1
●through the fog lamp switch and body grounds E24 and E50.
The fog lamp relay is energized and power is supplied
●from fog lamp relay terminal 5
●to terminal 1 of each fog lamp.
Ground is supplied to terminal 2 of each fog lamp through body grounds E24 and E50.
With power and ground supplied, the fog lamps illuminate.

LT-34
FRONT FOG LAMP
Wiring Diagram — F/FOG —
EKS003DG
TKWA0069E

FRONT FOG LAMP
LT-35
C
D
E
F
G
H
I
J
L
MA
B
LT
Aiming Adjustment EKS003DH
1. Set the distance between the screen and the center of the fog
lamp lens as shown at left.
2. Turn front fog lamps ON.
3. Adjust front fog lamps so that the top edge of the high intensity
zone is 100 mm (4 in) below the height of the fog lamp centers
as shown at left.
●When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp.
MEL327G
PKIA0545E
MEL328G

LT-36
FRONT FOG LAMP
Bulb Replacement
EKS003DI
1. Remove fog lamp. Refer toLT-36, "Removal and Installation" .
2. Turn plastic cap counter clockwise then remove it.
3. Unlock retaining spring, then remove bulb.
CAUTION:
●Do not touch the glass of bulb directly by hand. Keep
grease and other oily matters away from it. Do not touch
bulb by hand while it is lit or right after being turned off.
Burning may result.
●Do not leave bulb out of headlamp reflector for a long time
because dust, moisture smoke, etc. May affect the performance of headlamp. When replacing
bulb, be sure to replace it with new one.
●When bulb is installed, be sure to lock plastic cap to ensure watertightness.
Removal and Installation EKS003DJ
REMOVAL
1. Remove fender protector. Refer toEI-13, "FENDER PROTECTOR"
2. Disconnect fog lamp connector.
3. Remove fog lamp mounting bolt.
4. Pull out fog lamp from vehicle and disconnect connector.
INSTALLATION
●Install fog lamp in the reverse order of removal, observing the tightening torque shown below.
Fog lamp mounting boltFront fog lamp :12 V 55 W (H3)
PKIA0546E
PKIA0547E
Tightening torque :3.3 -7.7 N-m (0.33 - 0.79 kg-m, 29 - 69 in-lb)

REAR FOG LAMP
LT-37
C
D
E
F
G
H
I
J
L
MA
B
LT
REAR FOG LAMPPFP:26550
Wiring Diagram -R/FOG-/Without Front Fog LampEKS003BV
TKWA0070E

LT-38
REAR FOG LAMP
Wiring Diagram -R/FOG-/With Front Fog Lamp
EKS003BW
TKWA0071E

REAR FOG LAMP
LT-39
C
D
E
F
G
H
I
J
L
MA
B
LT
Bulb ReplacementEKS0015L
1. Remove rear fog lamp. Refer toLT- 3 9 , "Removal and Installa-
tion" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationEKS0015M
REMOVAL
1. Remove rear fog lamp mounting screws (2).
2. Take out rear fog lamp from bumper, then disconnect connector.
INSTALLATION
Install in the reverse order of removal, paying attention to the following. Rear fog lamp : 12V 21W
SKIA0052E
SKIA0090E
Rear fog lamp mounting screws
Tightening torque : 0.98 - 1.86 N-m (0.10 - 0.18 kg-m, 9-16 in-lb)

LT-40
CLEARANCE LAMP/TAIL LAMP
CLEARANCE LAMP/TAIL LAMP
PFP:26010
Bulb Replacement (Clearance Lamp)EKS001UR
Refer to LT- 4 , "HEADLAMP"
Bulb Replacement (Taillamp)EKS001US
Refer to LT-42, "REAR COMBINATION LAMP"
Removal and Installation of Clearance LampEKS001UT
Refer to LT- 4 , "HEADLAMP"
Removal and Installation of TaillampEKS001UU
Refer to LT-42, "REAR COMBINATION LAMP"