light PEUGEOT 1007 DAG 2008 User Guide

Page 20 of 194

1
23
Lack of oil
If "OIL" fl ashes and the service warn-
ing light comes on, accompanied by
an audible signal and a message on
the multifunction display, this indicates
a lack of oil which could damage the
engine.
If the lack of oil is confi rmed by a
check using the dipstick, it is essential
that the level is topped up.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approxi-
mately 5 seconds after the service indi-
cator display.
Oil level gauge fault
Check the oil level using the dipstick.
If "OIL --" fl ashes, this indicates a
malfunction of the engine oil level
gauge.
Consult a PEUGEOT dealer.
INSTRUMENT PANEL DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator
- total distance recorder (total and trip distances).
The level read on the dipstick
will only be correct if the
vehicle is on level ground
and the engine has been off
for more than 15 minutes.
Oil level correct

Note: the trip distance is displayed
for thirty seconds, when the ignition is
switched off, on opening and closing
the driver's door as well as on locking
the vehicle.
It also displays the "2 Tronic" gear-
box positions and operating modes
selected, as well as the information
relating to the cruise control or speed
limiter when one of these functions is
active.

Page 22 of 194

1
25
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears. Total/trip distance recorder
Briefl y pressing the button alternates
between the total and trip distance
displays.
To reset the trip distance recorder to
zero, when it is displayed press the
button until zeros appear.
Lighting rheostat
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the required bright-
ness, release the button.
After this operation, if you
wish to disconnect the bat-
tery, lock the vehicle and
wait for at least fi ve minutes,
otherwise the zero re-set will not be
registered.

Page 29 of 194


2
32
Vehicle confi guration
Once the "Vehicle confi guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- wiper linked with reverse gear,
- "follow-me-home" lighting. Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu
has been selected, you can gain ac-
cess to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty). Once you have selected a setting,
press the
"OK" button to change its
value.
Wait for approximately ten sec-
onds without any action to allow the
changed data to be recorded or press
the "ESC" button to cancel.
The display then returns to the normal
display. Units
Once the "Units" menu has been se-
lected, you can change the units of
the following parameters:
- temperature (°C or °F),
- fuel consumption (l/100, mpg or
km/l).
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.

Page 30 of 194

2
33
General menu
Press the "MENU" button to gain ac-
cess to the general menu, then press
the "

" or "

" buttons to scroll
through the following items:
- radio-CD,
- vehicle confi guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required. Vehicle confi guration
Once the "Vehicle confi guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- rear wiper linked with reverse
gear,
- "follow-me-home" lighting.
Presentation
This displays the following information,
via the WIP Sound control keypad:
- the time,
- the date,
- the outside temperature (this fl ashes if there is a risk of ice),
- the audio source displays (radio, CD, ...),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Antipollution system
faulty") or information messages
(e.g.: "Auto lights on"),
displayed temporarily, can be
cleared by pressing the "ESC"
button,
- the trip computer (see corresponding section).
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).
Radio-CD
With the WIP Sound switched on,
once the "Radio-CD" menu has been
selected, you can activate or deacti-
vate the functions linked with the use
of the radio (RDS following, REG
mode), the CD or the CD changer
(introscan, random play, CD repeat).

Page 33 of 194


2
36
Defi ne the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- wiper linked with reverse gear,
- "follow-me-home" lighting and duration.
Example: "Duration of the "follow-
me-home" lighting" Display confi guration
Once this menu has been selected,
you can access the following set-
tings:
- brightness-video setting,
- date and time setting,
- selection of the units.
Once you have selected a setting,
press the navigator.
Turn the navigator to change its value.
Press the navigator to record the
change and move on to the next set-
ting or press the
"ESC" button to
cancel. Selection of the language
Once this menu has been selected,
you can change the language
used on the display (Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil).
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.

Page 35 of 194


2
38
Defi ne the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- wiper linked with reverse gear,
- "follow-me-home lighting" and duration.
Example: "Duration of follow-me-
home lighting" Display confi guration
Once this menu has been selected,
you can gain access to the following
settings:
- brightness-video setting,
- date and time setting,
- selection of the units.
When you have selected a setting,
press the
"OK" button, then press
the
"" or "" buttons to change
its value.
Press the "OK" button to record the
change and move on to the next set-
ting or press the "ESC" button to
cancel. Selection of the language
Once this menu has been selected,
you can change the language
used by the display (Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil).
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.

Page 37 of 194


2
40
Selection of the language
Once the "Selection of the language"
menu has been selected, you gain
access to the following parameters:
- selection of the display, information and voice
commands language (Français,
English, Italiano, Portugues,
Espanol, Deutsch, Nederlands).
Display confi guration
Once the "Display confi guration"
menu has been selected, you gain
access to the following parameters:
- selection of the palette of colours available for the display,
- setting of the brightness and brilliance of the display,
- setting of the date and time (12 or 24 hour mode,
adjustment of the minutes on
GPS),
- selection of the units (temperature in °Celsius or
°Fahrenheit; consumption in
l/100 km or mpg or km/l).
Sounds
Once the "Sounds" menu has been
selected, you gain access to the fol-
lowing parameters:
- setting of the voice commands,
- setting of the voice synthesiser (volume of the instructions
and other messages, male or
female),
- activation of the auxiliary input AUX. Defi ne the vehicle parameters
Once the "Defi ne the vehicle parame-
ters" menu has been selected, you can
activate or deactivate certain driving
and comfort equipment:
- wiper linked with reverse gear
(refer to the "Visibility" section),
- "follow-me-home" lighting and duration (refer to the "Visibility"
section).
"Configuration" menu

 Press the "MENU" button on
the WIP Com to gain access to
the general menu .

 Turn the dial to select the

"Confi guration" menu, then
press it to confi rm.
Once this menu has been selected,
you can gain access to the following
functions:

Page 38 of 194

2
41

 Select the line "Duration of the
"follow-me-home" lighting" then
confi rm.
Example: setting the duration of the
"follow-me-home" lighting.

 Turn the dial to select the

"Lighting confi guration"
menu, then press it to confi rm.

 Select the duration then press
the dial.

 Turn the dial to set the value
required (15, 30 or 60 seconds),
then press the dial.

 Select the "OK" box, then
confi rm. The WIP Com must reini-
tialise and restart in order
to change the voice used by
the voice synthesiser (male
or female) or the language
used by the system.
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.

Page 41 of 194

3
44
Turn the control from blue
(cold) to red (hot) to adjust
the temperature to your
requirements.
HEATING/VENTILATION
The heating and ventilation can only
operate when the engine is running.
1. Temperature adjustment
Version with button and indicator light Version with manual control
2. Air fl ow adjustment Turn the control from posi-
tion 1 to position 4 to obtain
a fl ow of air suffi cient to en-
sure your comfort.
To maintain a certain level of comfort
in the passenger compartment, avoid
position 0 as much as possible.
However, in position 0 , a slight fl ow
of air, due to the movement of the
vehicle, can still be felt.

Page 42 of 194

3
45
3. Air distribution adjustment Version with manual control
Windscreen and side
windows.
Windscreen, side windows
and footwells.
Footwells (vents closed).
Centre and side vents. 5. Demisting the rear screen and
exterior mirrors
With the engine running,
pressing the button once
demists the rear screen
and the exterior mirrors.
This switches off automatically in re-
lation to the exterior temperature and
to prevent an excessive consumption
of current.
It is possible to stop demisting by
pressing the button again before it is
switched off automatically.
4. Air intake/Air recirculation
The interior air recirculation function
enables you to isolate the passenger
compartment from exterior odours
and smoke.
The outside air intake function pre-
vents condensation on the windscreen
and side windows.
Pressing button
4 permits re-
circulation of the interior air.
This is indicated by illumina-
tion of the indicator light.
As soon as possible, move the manual
control 4 to the left or press button 4
again to permit the intake of outside
air to prevent deterioration of the air
quality and misting of the windscreen
and side windows. This is indicated by
the switching off of the indicator light
for the button version. Move the manual control
4
to the right for the "Interior
air recirculation" position.
Version with button and indicator
light To quickly de-ice or demist
the windscreen and side
windows:
The air distribution can be adjusted
by placing the control in an interme-
diate position, marked by
"


Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 70 next >