PEUGEOT 4007 2010.5 Owners Manual

Page 141 of 215

9
PRACTICAL INFORMATION
Spare fuses
The spare fuses are located under the engine compartment
fuse box cover. The cover does not contain spare fuses with an am-
perage of 7.5 A, 25 A or 30 A. If one of the fuses with
these amperages develops a fault, replace it with the
following fuse:
A 7.5 A fuse must be replaced with the 10 A spare
fuse , a 25 A fuse with a 20 A spare fuse and a 30 A
fuse with the audio system fuse (N° 31) .
* The maxi-fuses provide additional protection for the elect
rical systems. All work on the maxi-fuses must be carried
out by a PEUGEOT dealer.

Fuse N° Rating
Functions

22 20 A Engine control unit, water in Diesel detector, injection
pump (Diesel), air fl ow sensor, water
presence sensors, oxygen sensor, camshaft position sensor, canister purg e electrovalve,
vehicle speed sensor, variable timing (VTC) electrovalve, EGR electro valve.

23 15 A Petrol pump, fuel gauge.

24 * 30 A Starter.

25 - Not used.

26 * 40 A ABS control unit, ASC control unit.

27* 30 A ABS control unit, ASC control unit.

28 * 30 A Condenser fan.

29 * 40 A Radiator fan.

30 30 A Passenger compartment fusebox.

31 30 A Audio amplifi er.

32 30 A Diesel engine control unit.

Fuse N° Rating

33 10 A

34 15 A

35 20 A

Page 142 of 215

9
PRACTICAL INFORMATION
The battery A is located under the bon-
net on the left.
To gain access to it:

 open the bonnet using the interior
release lever, then the exterior safe-
ty catch,

 secure the bonnet stay.
BATTER BATTERY
Access to the battery

 Connect the red cable to the posi-
tive terminal (+) of the fl at battery A ,
then to the positive terminal (+) of
the slave battery B .
 Connect one end of the green or
black cable to the negative termi-
nal (-) of the slave battery B .

 Connect the other end of the green
or black cable to an earth point C on
the broken down vehicle, as far as
possible from the battery (for exam-
ple, right-hand engine mounting).

 Start the engine of the assisting ve-
hicle.


Operate the starter, let the engine run.

 Wait until the engine returns to idle
and disconnect the cables.

 Raise the front of the cover 1 to re-
lease the three clips 2 .

 Then pull the cover 1 towards you
to release the clip 3 and remove the
cover.
Check the electrolyte level regu-
larly. If necessary, top up the
level with distilled water.
Starting using another battery
Looking for an earth point at
the right-hand engine mounting

Page 143 of 215

9
PRACTICAL INFORMATION
The batteries contain harmful
substances such as sulphuric
acid and lead. They must be
disposed of in accordance with
regulations and must not, in any
circumstances, be discarded
with household waste.
Take used remote control bat-
teries and vehicle batteries to a
special collection point.
Charging the battery using a
battery charger

 Disconnect the battery from the
vehicle.

 Remove the battery and place it in a
ventilated area.

 Remove the top-up caps and top
up the level with distilled water if ne-
cessary.

 Connect the battery to the charger
observing the instructions for use
provided by the manufacturer and
start charging.

 Disconnect the battery from the
charger and let it to cool.

 If necessary, top up the level with
distilled water.

 Clean the top of the battery care-
fully.

 Put the top-up caps back in place.

 Check that the terminals and
connectors are clean. If they are
covered with sulphate (whitish or
greenish deposit), remove them
and clean them.

 Reconnect the battery starting with
the positive terminal (+). It is advisable to disconnect the
battery if the vehicle is to be left
unused for more than one month.
Do not disconnect the terminals
while the engine is running.
Do not charge the batteries with-
out disconnecting the terminals
fi rst.
Avoid prolonged contact of the
electrolyte with the skin.
Most of these fl uids are harmful
to health and very corrosive. When charging the battery, it is
normal to observe an increase
in temperature and bubbling of
the electrolyte.
Before disconnecting the battery
Wait 2 minutes after switching off the igni-
tion before disconnecting the battery.
Close the windows, the sunroof, the
doors and the tailgate before disconnect-
ing the battery.
Following reconnection
of the battery
Following reconnection of the battery,
switch on the ignition and wait 1 minute
before starting to permit initialisation of
the electronic systems. However, if slight
diffi culties are encountered following this
operation, contact a PEUGEOT dealer.
Referring to the corresponding section,
you must yourself reinitialise:
- the one-touch electric windows,
- the sunroof,
- the satellite navigation system.

Page 144 of 215

9
PRACTICAL INFORMATION
CHANGING A WIPER BLADE CHANGING A WIPER BLADE
Removing a front or rear wiper
blade

 Raise the corresponding wiper arm.

 Remove the wiper blade, sliding it
towards the outside.
Fitting a front or rear wiper
blade

 At the front, check the size of the
wiper blade as the shorter blade is
fi tted on the right-hand side of the
vehicle.

 Put the corresponding new wiper
blade in place and fi x it.

 Fold down the wiper arm carefully.

Page 145 of 215

9
PRACTICAL INFORMATION
TOWING TOWING
Access to the tools Having your vehicle towed
on a flatbed

 Below the front bumper, install the
towing system on the towing eye 1 .
The towing eye and the tools are stored
in the storage compartment in the right-
hand boot trim.
To gain access to them:

 open the boot,

 turn button A to the left,

 remove the cover B ,

 remove the fi xing band C and take
out the tool bag D containing the
tools,

 take the towing eye and the tools re-
quired out of the tool bag. Place the gear lever in neutral.

Always have the vehicle towed
on a fl atbed.
Never have the vehicle towed
with the four wheels on the
ground, this could damage the
transmission.
The vehicle must not be towed
with the front or rear wheels on
the ground even if it is in front
"2WD" (2 wheel drive) mode. Towing another vehicle

 On the rear bumper, remove the
cover by pulling at the bottom using
the jack handle 2 .

 Screw in the towing eye fully using
the wheelbrace 3 .

 Install the towbar.

 Switch on the hazard warning lamps
on the towed vehicle.
When being towed with the en-
gine off, there is no longer any
braking or steering assistance.

Page 146 of 215

9
PRACTICAL INFORMATION
TOWING TOWING A TRAILER,
CARAVAN, ETC. CARAVAN, ETC.
Driving advice The maximum towing load on a long
slope depends on the gradient and the
outside temperature.
In all cases, pay attention to the coolant
temperature.
Side wind

 Take into account the increased
sensitivity to side wind.
Cooling
Towing a trailer on a slope increases
the temperature of the coolant.
As the fan is electrically controlled, its
cooling capacity is not dependent on
the engine speed.

 To lower the engine speed, reduce
your speed. Braking
Towing a trailer increases the braking
distance.
Tyres

 Check the tyre pressures of the tow-
ing vehicle and of the trailer, observ-
ing the recommended pressures.
Lighting

 Check the lighting and signalling on
the trailer.
 If this message is dis-
played, stop your ve-
hicle as soon as it is
safe to do so.
If the message fl ashes
slowly, wait for the engine to cool before
topping up the level, if necessary.
If the message fl ashes rapidly, contact
a PEUGEOT dealer without delay.
Opening of the lower tailgate is
prohibited if a towbar is being
used.
We recommend the use of genu-
ine PEUGEOT towbars and their
harnesses that have been tested
and approved from the design
stage of your vehicle and that the
fi tting of the towbar is entrusted
to a PEUGEOT dealer.
If the towbar is not fi tted by a
PEUGEOT dealer, it is impera-
tive that it is fi tted using the
electrical pre-equipment located
at the rear of the vehicle and in
accordance with the manufac-
turer's instructions.
Driving with a trailer subjects the
towing vehicle to more signifi -
cant stress and its driver must
be particularly careful.
Your vehicle is primarily designed for
transporting people and luggage, but it
may also be used for towing a trailer.
Distribution of loads

 Distribute the load in the trailer so
that the heaviest items are as close
as possible to the axle and the nose
weight approaches the maximum
permitted without exceeding it.
Air density decreases with altitude, thus
reducing engine performance. Above
1 000 metres, the maximum towing
load must be reduced by 10 % of the
GTW and so on for every 1 000 metres
of altitude.
Refer to the "Technical Data" section for
details of the weights and towing loads
which apply to your vehicle.

Page 147 of 215

9
PRACTICAL INFORMATION
FITTING ROOF BARS
Maximum authorised weight
on the roof bars, for a loading
height not exceeding 40 cm (ex-
cept bicycle carriers): 80 kg.
If the height exceeds 40 cm,
adapt the speed of the vehicle
to the condition of the road, to
avoid damaging the roof bars
and the fi xings on the roof.
Please refer to national legisla-
tion to comply with the regula-
tions regarding the transportation
of objects which are longer than
the vehicle.
Consult a PEUGEOT dealer for the in-
stallation of longitudinal roof bars.
When fi tting transverse roof bars, en-
sure that they are positioned correctly
as shown by marks on the longitudinal
roof bars.
Use accessories recommended by
PEUGEOT and follow the accessory
manufacturer's fi tting instructions.
In order to place a load on the roof, your
vehicle must be fi tted with longitudinal
roof bars with transverse roof bars fi tted
on top of these.
The longitudinal roof bars cannot be re-
moved.

Page 148 of 215

9
PRACTICAL INFORMATION
The fi tting of electrical equip-
ment or accessories which are
not recommended by PEUGEOT
may result in a failure of your
vehicle's electronic system.
Please note this specifi c warn-
ing. You are advised to contact
a your dealer to be shown the
range of recommended equip-
ment and accessories.
ACCESSORIES ACCESSORIES
"Protection": "Touring":
"In-car technology":
"Styling":
"Universal":
* To prevent any risk of jamming of the pedals:
- ensure that the mat is positioned and secured correctly,
- never fi t one mat on top of another. Depending on the country in
which the vehicle is sold, it is
compulsory to have a high vis-
ibility jacket, warning triangle
and spare bulbs available in the
vehicle.
anti-theft alarm, window etch-
ing, wheel security bolts, fi rst
aid kit, warning triangle, high
visibility jacket, stolen vehicle
tracking system, anti-skid cov-
ers, tyre under-infl ation detec-
tion, rear parking sensors. mats * , boot tray, dog guard,
PVC door sills, cool box.
For leisure pursuits: roof bars,
bicycle carrier on roof bars,
ski carrier, roof box, booster
seats and child seats, side
blinds.
Trailer towbar which must be fi tted by
the PEUGEOT network.
MP3/USB audio systems,
audio-telephone, amplifi ers,
satellite navigation systems,
hands-free kit, speakers, DVD
player, connection kit for MP3
player or portable CD player,
rear parking sensors, alarm. door defl ectors, rear styling
strips, 18 inch alloy wheels,
chromed exterior mirror shells,
chromed door handle shells,
diffuser on rear bumper, side
protection mouldings, aluminium
boot sill.
screenwash, interior and ex-
terior maintenance and clean-
ing products.
It is advisable to contact a
PEUGEOT dealer before install-
ing accessory radio communica-
tion transmitters with an external
aerial on your vehicle.
The PEUGEOT network will pro-
vide the specifi cations (frequency
band, maximum output power,
aerial position, special installa-
tion conditions) of the transmitters
which can be fi tted, in accordance
with the Motor Vehicle Electro-
magnetic Compatibility Directive
(2004/104/EC).
You can obtain a wide range of
accessories and original parts from the
PEUGEOT network.
These accessories and parts have
been tested and approved for reliability
and safety.
They are all adapted to your vehicle
and benefi t from PEUGEOT's recom-
mendation and warranty.
The product range offered by PEUGEOTAccessories is structured around 5 categories: PROTECTION - TOURING - IN-CAR TECHNOLOGY - STYLING -
UNIVERSAL.

Page 149 of 215

10
TECHNICAL DATA
ENGINES AND GEARBOXES ENGINES

Model codes
VUSFY0 -
VVSFY0
VUSFY9 -
VVSFY9
V
U4HK8 -
VV4HK8
VU4HK8

VU4HK8/1P

VV4HK8

VV4HK8/
1P

Engine
2.4 litre 16V 2.2 litre HDI PEF 16V
Cubic capacity (cc) 2 360 2 179
Bore x stroke (mm) 88 x 97 85 x 96
EU standard maximum power (kW) 125 115
Max power engine speed (rpm) 6 000 4 000
EU standard max torque (Nm) 232 380
Max torque engine speed (rpm) 4 100 2 000
Fuel Unleaded Diesel
Catalytic converter yes yes
Particle emission fi lter (PEF) no yes

Gearbox Manual
(5-speed) CVT
(6-speed) Manual
(6-speed) DCS
(6-speed)

Oil capacity (in litres)

Engine - 5.25

Page 150 of 215

10
TECHNICAL DATA
WEIGHTS AND TOWED LOADS (IN KG) OWED LOADS (IN KG)
* The kerb weight is equal to the weight without load + driver (75 kg).
** The speed of a towing vehicle must not exceed 60 mph (100 km/h) (comply with the legislation in force in your country).
*** The braked trailer value corresponds to the towing cap acities of the vehicle on a 12 % gradient.
High ambient temperatures may result in a reduction in the pe rformance of the vehicle in order to protect the engine; reduce
the towed weight by 450 kg when your altitude increases by 1 000 m.

Engines
2.4 litre 16V 2.2 litre HDI PEF 16V

Gearbox
Manual
(5-speed)
CVT
(6-speed)
Manual

(6-speed)
DCS
(6-speed)

Model codes VUSFY0 VVSFY0 VUSFY9 VVSFY9 VU4HK8 VV4HK8
VU4HK8

VU4HK8/
1P
VV4HK8

VV4HK8/
1P

Version 5 seats 7 seats 5 seats 7 seats 5 seats 7 seats 5 seats 7 seats

Page:   < prev 1-10 ... 101-110 111-120 121-130 131-140 141-150 151-160 161-170 171-180 181-190 ... 220 next >