app SATURN VUE 2009 Owner's Guide

On some vehicles, the mute button
can be used to dial numbers into
voice mail systems, or to dial phone
extensions. See the OnStar Owner’s
Guide for more information.
How OnStar Service Works
The OnStar system can record
and transmit vehicle information.
This information is automatically
sent to an OnStar Call Center when
the OnStar button is pressed, the
emergency button is pressed, or if
the airbags or AACN system deploy.
This information usually includes
the vehicle’s GPS location and,
in the event of a crash, additional
information regarding the crash that
the vehicle was involved in (e.g. the
direction from which the vehicle was
hit). When the Virtual Advisor feature
of OnStar Hands-Free Calling is
used, the vehicle also sends OnStar
the vehicle’s GPS location so they
can provide services where it is
located.OnStar service cannot work
unless the vehicle is in a place
where OnStar has an agreement
with a wireless service provider for
service in that area. OnStar service
also cannot work unless the vehicle
is in a place where the wireless
service provider OnStar has hired
for that area has coverage, network
capacity and reception when the
service is needed, and technology
that is compatible with the OnStar
service. Not all services are available
everywhere, particularly in remote
or enclosed areas, or at all times.
Location information about the
vehicle is only available if the GPS
satellite signals are unobstructed
and available.
The vehicle must have a working
electrical system, including adequate
battery power, for the OnStar
equipment to operate. There areother problems OnStar cannot
control that may prevent OnStar
from providing OnStar service at
any particular time or place. Some
examples are damage to important
parts of the vehicle in a crash, hills,
tall buildings, tunnels, weather or
wireless phone network congestion.
Your Responsibility
Increase the volume of the radio if
the OnStar advisor cannot be heard.
If the light next to the OnStar buttons
is red, the system may not be
functioning properly. Press the
OnStar button and request a vehicle
diagnostic. If the light appears clear
(no light is appearing), your OnStar
subscription has expired and all
services have been deactivated.
Press the OnStar button to conrm
that the OnStar equipment is active.
2-36 Features and Controls
ProCarManuals.com

7. Firmly press and release the
“Learn” or “Smart” button.
After you press this button,
you will have 30 seconds
to complete Step 8.
8. Immediately return to the vehicle.
Firmly press and hold the
Universal Home Remote button,
chosen in Step 3 to control the
garage door, for two seconds,
and then release it. If the garage
door does not move, press and
hold the same button a second
time for two seconds, and then
release it. Again, if the door does
not move, press and hold the
same button a third time for
two seconds, and then release.
The Universal Home Remote
should now activate the
garage door.
To program the remaining two
Universal Home Remote buttons,
begin with Step 2 of “Programming
the Universal Home Remote
System.” Do not repeat Step 1,as this will erase all previous
programming from the Universal
Home Remote buttons.
Gate Operator and Canadian
Programming
If you have questions or need
help programming the Universal
Home Remote System, call
1-800-355-3515 or go to
homelink.com.
Canadian radio-frequency laws
require transmitter signals to time
out or quit after several seconds
of transmission. This may not be
long enough for Universal Home
Remote to pick up the signal during
programming. Similarly, some U.S.
gate operators are manufactured to
time out in the same manner.
If you live in Canada, or you are
having difficulty programming a
gate operator or garage door opener
by using the “Programming Universal
Home Remote” procedures,regardless of where you live,
replace Step 3 under “Programming
Universal Home Remote” with the
following:
Continue to press and hold the
Universal Home Remote button
while you press and release every
two seconds (cycle) the hand-held
transmitter button until the frequency
signal has been successfully
accepted by the Universal Home
Remote. The Universal Home
Remote indicator light will ash
slowly at rst and then rapidly.
Proceed with Step 4 under
“Programming Universal Home
Remote” to complete.
Using Universal Home Remote
Press and hold the appropriate
Universal Home Remote button for at
least half of a second. The indicator
light will come on while the signal is
being transmitted.
2-40 Features and Controls
ProCarManuals.com

Rear Window
Wiper/Washer
The rear wiper and rear wash
button is located on the instrument
panel above the climate control
system.
=(Rear Wiper/Washer):Press to
wash and wipe the rear window.
The rear window washer uses the
same reservoir as the windshield
washer. Check the windshield
washer reservoir level if the front
windshield can be worked, but no
uid is sprayed when the rear washer
is activated. SeeWindshield Washer
Fluid on page 5-27.
5(Delay):Press to turn the
delayed wiping on or off.
Cruise Control
With cruise control, the vehicle can
maintain a speed of about 25 mph
(40 km/h) or more without keeping
your foot on the accelerator. Cruise
control does not work at speeds
below 25 mph (40 km/h).
On vehicles with the StabiliTrak
®
feature, the system may begin to limit
wheel spin while you are using cruise
control. If this happens, the cruise
control will automatically disengage.
SeeStabiliTrak
®System on
page 4-7.
{CAUTION
Cruise control can be dangerous
where you cannot drive safely at
a steady speed. So, do not use
the cruise control on winding
roads or in heavy traffic.
Cruise control can be dangerous
on slippery roads. On such roads,
fast changes in tire traction can
cause excessive wheel slip, and
you could lose control. Do not use
cruise control on slippery roads.
Instrument Panel 3-9
ProCarManuals.com

Setting Cruise Control
{CAUTION
If you leave your cruise control
on when you are not using cruise,
you might hit a button and go into
cruise when you do not want to.
You could be startled and even
lose control. Keep the cruise
control switch off until you want
to use cruise control.
The cruise control buttons are
located on the left side of the
steering wheel.
E(On/Off):Press to turn the
cruise control system on and off.
An indicator light comes on.
RES+ (Resume/Accel):Move
the thumbwheel up to resume a set
speed or to accelerate to a higher
speed.
−SET (Set/Coast):Move the
thumbwheel down to set a speed
or to decrease the speed.
To set a speed:
1. Press
Eto turn cruise control on.
The indicator light on the button
comes on.
2. Get to the speed desired.
3. Press the thumbwheel toward
−SET and release it.
4. Take your foot off the accelerator
pedal.
When the brakes are applied,
the cruise control shuts off.Resuming a Set Speed
If the cruise control is set at a
desired speed and then the brakes
are applied, the cruise control is
disengaged. The indicator light on
the instrument panel cluster goes
out when the cruise is no longer
engaged. To return to the previously
set speed, press the thumbwheel
up toward RES+ briey when the
vehicle has reached a speed of
about 25 mph (40 km/h) or more.
This accelerates the vehicle to the
previously selected speed.
Increasing Speed While Using
Cruise Control
To increase the cruise speed while
using cruise control:
Move the thumbwheel up toward
RES+ and hold it until the vehicle
accelerates to the desired speed,
and then release the switch.
3-10 Instrument Panel
ProCarManuals.com

To increase the speed in small
amounts, move the thumbwheel
up toward RES+ briey and then
release it. Each time this is done,
the vehicle goes about 1 mph
(1.6 km/h) faster.
Use the accelerator pedal to
reach the desired speed and
move the thumbwheel towards
−SET. The new desired speed
must be greater than the previous
set speed by a least 5 mph.
Reducing Speed While Using
Cruise Control
If the cruise control system is
already engaged,
Move the thumbwheel toward
−SET and hold until the desired
lower speed is reached, then
release it.
To slow down in very small
amounts, move the thumbwheel
toward−SET briey. Each time
this is done, the vehicle goes
about 1 mph (1.6 km/h) slower.Passing Another Vehicle While
Using Cruise Control
Use the accelerator pedal to
increase the vehicle’s speed.
When you take your foot off the
pedal, the vehicle will slow down
to the previously set cruise control
speed.
Using Cruise Control on Hills
How well the cruise control works
on hills depends upon the vehicle’s
speed, load, and the steepness of
the hills. When going up steep hills,
you might have to step on the
accelerator pedal to maintain the
vehicle’s speed. When going
downhill, you might have to brake or
shift to a lower gear to maintain the
vehicle’s speed. For some vehicles
the transmission may automatically
downshift when going down hills to
help maintain the vehicle’s speed.
When the brakes are applied the
cruise control shuts off.Ending Cruise Control
There are three ways to disengage
the cruise control:
Step lightly on the brake pedal
or clutch; when cruise control
disengages, the indicator light
on the instrument panel cluster
goes out.
PressEto turn off the cruise
control system.
Erasing Speed Memory
The cruise control set speed
memory is erased when the
cruise control or the ignition is
turned off.
Instrument Panel 3-11
ProCarManuals.com

)(Bi-Level):Air is divided
between the instrument panel
and the oor outlets.
6(Floor):Air is directed to the
oor outlets with some air directed
to the windshield.
When this mode is selected, the
system turns the recirculation mode
off. Recirculation mode cannot
be selected while in oor mode.
This helps prevent window fogging.
-(Defog):This mode clears
the windows of fog or moisture.
Air is directed to the oor outlets,
with some air directed to the
windshield and side window outlets.
In this mode, the system turns the
recirculation mode off and runs the
air conditioning compressor unless
the outside air is at or below freezing.
Recirculation mode cannot be
selected while in defog mode.
This helps prevent window fogging.
0(Defrost):This mode removes
fog or frost from the windshield
more quickly. Air is directed to the
windshield and the side window
outlets. In this mode, the system
turns the recirculation mode off
automatically and runs the air
conditioning compressor unless the
outside air is at or below freezing.
Recirculation mode cannot be
selected while in defrost mode.
This helps prevent window fogging.
For best results, clear all snow and
ice from the windshield before
defrosting.
#(Air Conditioning):Press to
turn the air conditioning system on
or off. An indicator light comes on to
show that the air conditioning is on.
The air conditioning can be selected
in any mode as long as the fan is on
and the outside temperature is above
freezing. A ashing indicator light
indicates that the air conditioning
compressor is currently not available.On hot days, open the windows to
let hot inside air escape; then close
them. This helps reduce the time it
takes for the vehicle to cool down
and helps the system to operate
more efficiently.
For quick cool down on hot days,
select the following settings
together:
1. Select
Hmode.
2. Select
;.
3. Turn the
#on.
4. Select the coolest temperature
and highest fan speed.
5. Once the vehicle’s interior
temperature is below the outside
temperature, select recirculation
mode for enhanced cooling.
Using these settings together for
long periods of time may cause the
air inside the vehicle to become too
dry. To prevent this from happening,
after the air inside of the vehicle
has cooled, turn the recirculation
mode off.
3-18 Instrument Panel
ProCarManuals.com

The air conditioning system
removes moisture from the air, so a
small amount of water might drip
under the vehicle while idling or after
turning off the engine. This is normal.
;(Outside Air):Press to turn the
outside air mode on. An indicator
light comes on to show that outside
air is on. Air from outside the vehicle
will circulate throughout the vehicle.
The outside air mode can be used
with all modes, but it cannot be
used with the recirculation mode.
Pressing this button will cancel the
recirculation mode.
@(Recirculation):Press to
turn on the recirculation mode.
An indicator light comes on to show
that recirculation is on. This mode
recirculates and helps to quickly
cool or heat the air inside the vehicle.
It can be used to prevent outside air
and odors from entering the vehicle.
Avoid using the recirculation mode
during high periods of humidity
and cool outside temperatures
since this may result in increased
window fogging. If window fogging
is experienced, select the
defrost mode.
Recirculation mode is not available in
oor, defog or defrost modes and will
shut off automatically and change to
outside air. The indicator will ash if
the button is selected in any of these
modes. This helps prevent window
fogging and moisture building up
inside the vehicle.Rear Window Defogger
The rear window defogger uses a
warming grid to remove fog from the
rear window.
The rear window defogger only
works when the ignition is in
ON/RUN.
<(Rear Window Defogger):
Press to turn the rear window
defogger on or off. An indicator light
on the button comes on to show
that the rear window is activated.
The rear window defogger stays
on for approximately 10 minutes
after the button is pressed, unless
the ignition is turned to ACC/
ACCESSORY or LOCK/OFF.
If turned on again, the defogger only
runs for approximately ve minutes
before turning off again. At higher
vehicle speeds, the defogger may
stay on continuously. The defogger
can also be turned off by turning off
the engine.
Instrument Panel 3-19
ProCarManuals.com

On hot days, use the automatic fan
and automatic air delivery mode
settings and the vehicle will reach the
desired temperature more quickly.
The desired fan and air delivery
mode settings can still be adjusted
manually. Open the windows to let
the hot inside air escape, then close
them. This helps reduce the time it
takes for the vehicle to cool down
and helps the system to operate
more efficiently.
The air conditioning system removes
moisture from the air, so a small
amount of water might drip under the
vehicle while idling or after turning off
the engine.
;(Outside Air):Press to turn
the outside air mode on. An indicator
light comes on to show that outside
air is on. Air from outside the vehicle
will circulate throughout the vehicle.
The outside air mode can be used
with all modes, but it cannot be
used with the recirculation mode.
Pressing this button will cancel the
recirculation mode.
@(Recirculation):Press to
turn on the recirculation mode.
An indicator light comes on to show
that recirculation is on. This mode
recirculates and helps to quickly cool
or heat the air inside the vehicle.
It can be used to prevent outside air
and odors from entering the vehicle.
Avoid using the recirculation mode
during high periods of humidity
and cool outside temperatures
since this may result in increased
window fogging. If window fogging
is experienced, select the
defrost mode.
Recirculation mode is not available in
oor, defog or defrost modes and will
shut off automatically and change to
outside air. If the button is selected
in any of these modes, the indicator
will ash. This helps prevent window
fogging and moisture building up
inside the vehicle.Rear Window Defogger
The rear window defogger uses a
warming grid to remove fog from the
rear window.
The rear window defogger only
works when the ignition is in
ON/RUN.
<(Rear Window Defogger):
Press to turn the rear window
defogger on or off. An indicator light
on the button comes on to show
that it is activated.
The rear window defogger stays
on for approximately 10 minutes
after the button is pressed, unless
the ignition is turned to ACC/
ACCESSORY or LOCK/OFF.
If turned on again, the defogger only
runs for approximately ve minutes
before turning off. At higher vehicle
speeds, the defogger may stay on
continuously. The defogger can
also be turned off by turning off
the engine.
Instrument Panel 3-23
ProCarManuals.com

For vehicles with the remote start
feature, the rear defogger will
automatically turn on when remote
start is activated.
Notice:Do not use anything
sharp on the inside of the rear
window. If you do, you could cut
or damage the warming grid, and
the repairs would not be covered
by the vehicle warranty. Do not
attach a temporary vehicle
license, tape, a decal or anything
similar to the defogger grid.
Remote Start Climate Control
Operation
For vehicles with the remote start
feature and if it is activated, the
climate control system heats and
cools the inside of the vehicle using
the modes that were set before the
vehicle was turned off.Outlet Adjustment
Use the louvers located on the air
outlets to change the direction of the
airow.
Operation Tips
Clear away any ice, snow,
or leaves from the air inlets
at the base of the vehicle that
may block the ow of air into
the vehicle.
Do not use any non-GM
approved hood deectors
that could adversely affect the
performance of the system.
Keep the path under the front
seats clear of objects to help
circulate the air inside of
the vehicle more effectively.
Passenger Compartment
Air Filter
The lter removes dust, pollen, and
other airborne irritants from outside
air that is pulled into the vehicle.
The lter should be replaced as part
of routine scheduled maintenance.
SeeScheduled Maintenance on
page 6-3for replacement intervals.
To nd out what type of lter to use,
seeMaintenance Replacement Parts
on page 6-15.
The passenger compartment air
lter can be accessed by removing
the entire glove box.
1. Remove the six screws from
around the glove box and
detach the three inner clips
from the glove box.
3-24 Instrument Panel
ProCarManuals.com

Power Steering Warning
Lights
For 4-cylinder vehicles with Electric
Power Steering (EPS), this light
comes on briey when the ignition
is turned to ON/RUN as a check
to show it is working.
If it does not come on have the
vehicle serviced by your dealer/
retailer.
If the EPS light stays on, or comes
on while driving, the EPS system
may not be working. If this happens,
see your dealer/retailer for service.
Traction Control System
(TCS) Warning Light
The Traction Control System (TCS)
Warning Light shows one of these
two symbols.
This light comes on briey as the
engine is started. If it does not come
on have the vehicle serviced by
your dealer/retailer.
It also comes on when the Traction
Control System (TCS) has been
turned off or when the Electronic
Stability Program (ESP) is not ready.
If there is a problem with the TCS
or the ESP, this light and the TCS
warning light comes on at the
same time. SeeTraction Control
System (TCS) on page 4-8and
StabiliTrak
®System on page 4-7
for more information.
StabiliTrak®Indicator
Light
The StabiliTrak®light comes on
briey as the engine is started.
If it does not come on have
the vehicle serviced by your
dealer/retailer.
This light ashes while the
StabiliTrack or the Traction Control
System (TCS) is working. The light
comes on when the ESP has been
turned off and if there is a problem
with the StabiliTrak or the TCS.
SeeTraction Control System (TCS)
on page 4-8andStabiliTrak
®System
on page 4-7for more information.
Instrument Panel 3-33
ProCarManuals.com