ECU SSANGYONG MUSSO 2003 Owners Manual

5D2-52 TRANSFER CASE (TOD)
32. Install shift shaft oil seal if it is not installed.
33. Using pliers equipped with soft jaws, rotate the triangularshaft so it is aligned with the triangular slot in the transfer
case shift motor. If triangular shaft will not rotate, rotate the rear output shaft.
34. Slightly loosen the two nuts that attach the slotted support bracket to the end of the motor house.
35. Apply Black Non-Acid Cure Silicone Rubber or equivalent to motor housing base and install on transfer case.
36. Install the transfer case shift motor and three bolts along with speed sensor wire harness bracket and tighten. NoticeThe wire harness must be routed as shown to provide clearance and to prevent the wire harness from grounding
the damper.
37. Holding the slotted support bracket tight against the motor housing end, secure the bracket to the transfer case,
tightening the bolt with lockwasher to 8-11 Nm (72-96 lb-in).
38. Retighten the two nuts that attach the slotted support bracket to the end of the motor.
39. Install the clutch coil wire terminal and sensor wires.

FATC-HAVC 7D-5
FATC BLOCK DIAGRAM
INCAR SENSOR
AMBIENT SENSOR
WATER TEMPERATURE SENSOR
SUN LOAD SENSOR
TEMPERATURE SWITCH
BLOWER SWITCH
MODE SWITCH
DEFROSTER SWITCH
INTAKE SWITCH
AUTO SWITCH
A/CON SWITCH
OFF SWITCH
TEMP DOOR POSITION FEEDBACKVOLTAGE
POWER TRANSISTOR COLLECTORVOLTAGE
VFD
MAX HI RELAY
POWER T/R
BLOWERMOTOR
ECUCOMPRESSOR
MIX ACTUATORMIX DOOR
INTAKE ACTUATORINTAKE DOOR
MODE ACTUATORMODE DOOR
Airconditioner output
C ON
T
RO L
UN I
T

8A-4 SEAT BELTGENERAL DESCRIPTION
AND SYSTEM OPERATION
DRIVER SEAT BELT WARNING The driver's safety belt incorporates a safety belt reminder light in the instment cluster remind the driver if the safety beltis not fastened when the ignition is turnd ON.
OPERATION AND FUNCTIONAL CHECKS Caution :
Keep sharp objects and potentially damaging objects away from the seat belts.
Avoid bending or damaging any portion of the buckleor the latch plate.
Do not bleach or dye the belt webbing. Use only mild soap and water in order to clean the belts.
When installing the seat belt anchor bolts and thescrews, start the bolts and screws by hand in order to prevent crossthreading.
Do not attempt any repairs on the retractormechsemblies with new assemblies.
Replace any belts that are cut r damaged in any way.
1. Inspect all saet belt anchor bolts and the screw in order to verify that they are secure.
2. Inspect the seat belt buckle. The buckle must lock and unlock easily.
3. After inserting the latch into the buckle, tug sharply on the belt. The buckle must remain locked.
4. Fully extend the shoulder belt portion to make sure that there is no twisting or tears in the belt.
5. Let the shoulder belt retract fully. The belt should retract easily.

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-3
CAUTIONS
Failure to follow the correct service procedure can cause air bag damage or personal injury due to unexpected air
bag deployment. Before service (removal and installation of part, check for replacement), please be weal noticed offollowing items for your correct service.
1. For service, turn the ignition switch to ‘LOCK’ position and wait for 30 seconds after disconnecting the negative battery cable.
2. If the vehicle collapsed, remove the air bag ECU first to reserve the crash records.
3, Never use other vehicles’ air bag components and replace with specified new part.
4. Never disassemble or repair the air bag module, air bag unit and wiring harness to re-use.
5. Replace the air bag module and air bag unit with new if it dropped, cracked or damaged.
6. Only qualified technicians in service shop should check or repair the air bag,
7. Before service, should be well noticed of warning labels on the vehicle.
A. Sun Visor Side
[Warning] Pull down the sun visor and see SRS air bag warning lamp on the head lining. B. Head Lining
[Warning]
1 . This vehicle is equipped with air bag. Air bag is supplemental device for the seatbelt. Fasten your seatbelt.
2. This air bag should be replaced by authorized supplier within replacement intervals.
3. When the ignition key is turned to ON position, SRS warning lamp will turn on for 6 sec. and go off. In this case, the system is normal. For the following cases, see service manual. - SRS warning lamp does not turn on. - SRS warning lamp does not go off.- SRS warning lamp continues to blink.
C. Steering Wheel Body Inner
[Warning] Before removing the steering wheel, read service manual first. Set the front wheels straight forward
and align the center position marks of SRS clock spring. Improper removal or installation of the steering wheel can damage the SRS components. D. Engine Compartment
[Warning] This vehicle is equipped with air bag. Before checking the engine compartment, read servicemanual first. Faultuy check and service can cause SRS air bag deployment and system defects that can be led to severe damage. E. Battery Cable
[Warning]
Before disconnecting the battery power, read service manual first.

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-11
Self-Diagnosis List
Fault
CodeDefects Service Hint
01 Driver’ s squib (+) side No. 1 Short of (+) side No. 1 in the driver ’ s squib circuit.
Check connection of connector.
Check the ECU.Appli-
cation
02 Driver’ s squib (+) side No. 2 Short of (+) side No. 2 in the driver ’ s squib circuit.
Check connection of connector.
Check the ECU.X
03 Driver’ s squib (+) side No. 3 Short of (+) side No. 3 in the driver ’ s squib circuit.
Check connection of connector.
Check the ECU.X
04 Driver’ s squib (+) side No. 4 Short of (+) side No. 4 in the driver ’ s squib circuit.
Check connection of connector.
Check the ECU.X
05 Driver’ s squib ground (-) side No. 1 Short of ground side No. 1 in the driver ’ s squib
circuit.
Check and replace the ECU.
06 Driver’ s squib ground (-) side No. 2 Short of ground side No. 2 in the driver ’ s squib
circuit.
Check and replace the ECU.X
07 Driver’ s squib ground (-) side No. 3 Short of ground side No. 3 in the driver ’ s squib
circuit.
Check and replace the ECU.X
08 Driver’ s squib ground (-) side No. 4 Short of ground side No. 4 in the driver ’ s squib
circuit.
Check and replace the ECU.X
09 Energy shutdown switch No. 1 Air bag control unit internal defects.
Check and replace the ECU.
10 Energy shutdown switch No. 2 Air bag control unit internal defects.
Check and replace the ECU.X
11 Energy shutdown switch No. 3 Air bag control unit internal defects.
Check and replace the ECU.X
12 Energy shutdown switch No. 4 Air bag control unit internal defects.
Check and replace the ECU.X
13 Ignition switch wire No. 1 Air bag control unit internal defects.
Check and replace the ECU.
14 Ignition switch wire No. 2 Air bag control unit internal defects.
Check and replace the ECU.X
15 Ignition switch wire No. 3 Air bag control unit internal defects.
Check and replace the ECU.X
16 Ignition switch wire No. 4XAir bag control unit internal defects.
Check and replace the ECU.

8B-12 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
Fault
CodeDefects Service HintAppli-
cation
17 Squib No. 1 resistance
18 Squib No. 2 resistanceX
19 Squib No. 3 resistanceX
20 Squib No. 4 resistanceX
21 Squib No. 1 resistance
22 Squib No. 2 resistanceX
Driver ’ s squib resistance is higher than standard (4.5±0.5W).
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Replace the squib wire.
Plus side short : 7k, ground side short : 6kW.
Driver ’ s squib resistance is higher than standard(4.5±0.5W).
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Replace the squib wire.
Plus side short : 7k, ground side short : 6kW.
Driver ’ s squib resistance is higher than standard (4.5±0.5W).
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Replace the squib wire.
Plus side short : 7k, ground side short : 6kW.
Driver ’ s squib resistance is higher than standard (4.5±0.5W).
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Replace the squib wire.
Plus side short : 7k, ground side short : 6kW.
Driver ’ s squib resistance is lower than standard(1.4±0.3W).
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Replace the squib wire.
Plus side short : 7k, ground side short : 6kW.
Driver ’ s squib resistance is lower than standard (1.4±0.3W).
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Replace the squib wire.
Plus side short : 7k, ground side short : 6kW.
23 Squib No. 3 resistanceXDriver ’ s squib resistance is lower than standard (1.4±0.3W).
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Replace the squib wire.
Plus side short : 7k, ground side short : 6kW.

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-13
Fault
CodeDefects Service HintAppli-
cation
24 Squib No. 4 resistance
X
25 Energy reserve No. 1 voltage
26 Energy reserve No. 2 voltageX
27 Energy reserve No. 3 voltageX
28 Energy reserve No. 4 voltageX
29 Energy reserve No. 5 voltage
30 Energy reserve No. 6 voltage
31 Energy reserve No. 1 current off capacity
32 Energy reserve No. 2 current offcapacityX
33 Energy reserve No. 3 current offcapacityX
34 Energy reserve No. 4 current off
capacityX
35 Energy reserve No. 5 current offcapacity
36 Condensor voltage
37 Collision times checksum
Driver ’ s squib resistance is lower than standard
(1.4±0.3W).
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Replace the squib wire.
Plus side short : 7k, ground side short : 6kW.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
4 1 Major USAAir bag control unit internal defects.
Check and replace the ECU.
38 Driver’ s acceleration sensor
39 Driver’ s acceleration sensor off-set
40 Arming sensor

Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.

8B-14 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
Fault
CodeDefects Service HintAppli-
cation
42 Over heat
4 3 SENS
44 Standard band gap
45 Temperature sensor
46 Warning lamp
47 Battery voltage
49 Fault code list
5 0 USA communication
51 LSA communication
52 No EEPROM program
53 EEPROM checksum
5 4 EEPROM map
55 External watchdog 1
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Open/short in the warning lamp circuit.
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Power wire voltage is out of standard voltage (9 - 16V).
Check the battery for voltage and charging.
Check related circuits for open/short.
Check connection of connector.
Check the ECU.
Air bag control unit internal defects.
Check the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
56 Arming sensor-no close
57 RAM check
5 8 System
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.
59 External watchdog 2
60 Pulse
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-15
Fault
CodeDefects Service HintAppli-
cation
127 Collision signal
128 Collision number
Air bag control unit internal defects.
Check and replace the ECU.
Air bag control unit internal defects.
Check and replace the ECU.

SUPPLEMENTAL RESTRAINT SYSTEM(SRS) 8B-19
Air Bag Horn (Relay) Remote Control (Electronic Circuit)
CLOCK SPRING
General SpecificationVoltage
Rating Operating VoltageCurrent Rating Air Bag Circuit Resistance Isolating ResistanceRotating Range DC 12V
DC 6 - 18V
10 - 30mA(6A,0.1second)
200 - 220mA
15mA
0.16 - 0.38 (-40°C - 85°C)
5M
2.7 - 3.1 Rotation from neutral Position to Both Sides
Notice
Clock spring can not be repaired.
Do not disassemble or modify.
To adjust to the center position, rotate clockwise until it stops and then rotate it counterclockwise 2.3 ± 0.2revolutions and align marks. If not, airbag system can
not work normally and driver can be injured seriously.