relay SSANGYONG NEW ACTYON SPORTS 2012 Workshop Manual

04-78210-01
Indicators on Instrument Cluster ▶
No. Symbol ItemBulb
TypePower Turning ON condition
1Turn signal lamp-L
LEDMultifunction
switchWhen activating switch
2 Turn signal lamp-R LEDMultifunction
switchWhen activating switch
34WD HIGH
indicatorLED IGN IGN ON/ CAN signal input
4Winter mode
indicatorLED IGN IGN ON/ CAN signal input
5Front fog lamp
indicatorLEDFog lamp
relayWhen activating switch
6Cruise control
indicatorLED IGN IGN ON/ CAN signal input
7Light illumination
indicator LED BATT Tail lamp ON
8High beam
indicatorLEDHeadlamp
high beam
relayWhen activating switch
9ABS warning lamp
LED IGNIGN ON/ CAN signal input
(ABS, EBD)
10 Glow indicator LED IGN IGN ON/ CAN signal input
11Immobilizer
indicatorLED IGN IGN ON/ CAN signal input
12Low fuel level
warnig lightLED IGNWhen analog inputting fuel
level

06-38610-08
1. SPECIFICATIONS
Multifunction switch ▶
Item Rated load Voltage drop
Light 0.1 A Max. 0.25 V
Dimmer & passing High beam: 0.3 A / Low beam: 0.3 A
/ Passing: 0.3 AMax. 0.25 V
Turn signal lamp switch 0.5 A Max. 0.25 V
Hazard warning flasher switch 0.1 A -
Fog lamp 0.1 A -
Wiper LOW: 5 A (motor load)
HI: 7 A (motor load)
AUTO: 0.22 A (relay load)
LOCK: Max. 28 A (motor load)Max. 0.25 V
Auto washer 0.1 A -
Wiper 4.5 A (motor load)
20 A (Lock/Min)Max. 0.8 V
INT 25 mA -
MIST 5 A (motor load) Max. 0.25 V
Hazard warning flasher bezel switch ▶
Item Rated load
Hazard warning flasher switch 12 V-10 A
Rear heated glass switch 12 V-0.1 A
Windshield heated glass switch 12 V-0.1 A
TRIP switch 12 V-0.1 A
Outside rearview mirror control bezel switch ▶
Item Rated load
Outside rearview mirror switch 12 V-2 A
ESP OFF switch 12 V-0.1 A
Mirror folding switch 12 V-0.1 A

07-77810-01
2) STICS Control Logic Related to Wiper and Washer
Wiper MIST and Front Washer Coupled Wiper ▶
The wiper relay is turned on 0.3 seconds after turning "ON" the washer switch for 0.1 ~
0.59 seconds with the ignition key "ON", and it is turned off when the parking terminal is
turned off. 1.
The wiper relay is turned on at 0.3 seconds after from the time when the washer switch is
turned on for more than 0.6 seconds with the ignition switch "ON". The wiper relay gets on
3 times immediately after turning off the washer switch. 2.

08-4
STICS Engine Compartment Fuse Box
STICS ▶
The rain sensing unit detects the amount of rain drops and sends the operating signal to STICS,
and STICS drives the wiper directly. At this moment, STICS determines the wiper operation mode
(washer, MIST, AUTO), then sends the information to the rain sensor.
Auto Light Sensor and Rain Sensor Coupled Control ▶
Rain detected headlamp: If it rains heavy which requires the highest INT speed (almost
LOW), the headlamps are turned on automatically. -
Night detected wiping: When the auto light control turns on the headlamps and the rain
sensor detects the rain, the wiper sensitivity is automatically increased by one level in
comparison with daytime.
(i.e. the AUTO wiper switch is at the 3rd level, but the wiper operates at the 4th level.) -Wiper relay (HI)
Wiper relay (LO)

08-58610-09
1) Power-up Reminder Wiper Function
When turning off and on the auto INT switch, the system drives the wiper motor through
LOW relay regardless of communication with rain sensor. 1.
When turning the INT-AUTO switch from the "OFF" to "ON" position with the ignition
switch in the "ON" mode, the LOW relay operates to drive the wiper motor for 1 cycle,
regardless of the rain sensor communication.
After that, when turning the INT-AUTO switch from the "OFF" to "ON" position, the LO
W
relay operates to drive the wiper motor for 1 cycle only if data from the rain sensor
indicates rain drops. 2.
2. FUNCTIONS OF RAIN SENSING WIPER

08-78610-09
3) Sensitivity Control
The wiper LOW relay is turned on and the wiper motor runs one cycle when the volume
<009a008c0095009a0090009b0090009d0090009b00a000470090009a004700900095008a0099008c0088009a008c008b0047004f008c009f00610047009a008c0095009a0090009b0090009d0090009b00a00047005700470d7d0047005800500047009e00
8f00900093008c0047009b008f008c00470090008e00950090>tion switch and the INT switch is
in the "ON" position, and the wiper motor is in "Parked" position). However, the wiper
motor can be operated only when the rain sensor detects the "Rain Detected" signal. 1.
If the volume sensitivity is changed more than 1 stage within 2 seconds, the wiper motor runs
only one cycle.
4) Auto Light Control
Only when the auto light switch is in "AUTO" position, it controls the tail lamp and
headlamp by communicating with the rain sensor (while the ignition key is in "ON"
position). 1.

08-98610-09
6) Defective Rain Sensor
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 3 from 4 during receiving the malfunction signal from the rain
sensor, while the ignition key is in "ON" position and the wiper switch is in "ON" position. 2.The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 2 from 3 during receiving the malfunction signal from the rain
sensor, while the ignition key is in "ON" position and the wiper switch is in "ON" position. 1.

08-110000-00
Pause Time Table of Vehicle Speed Coupled INT Wiper ▶
Speed sensitive INT (intermittent) wiper 1.Pause time against vehicle speed ▶
Cautions for wiper control ※
The wiper relay continues to output for remaining "ON" time even when the INT switch is
turned off during its operation.
IGN switch "ON", INT switch "OFF": Resume the intermittent time when turning "ON".
IGN switch "ON", INT switch "ON": Resume the intermittent time when turning "ON". -
-
-
Controls when the wiper motor parking is defective 2.
The wiper relay continues to output when the parking terminal is fixed at the ground or
IGN while the wiper relay is "ON" i.e., with the INT switch ON or washer switch ON. (The
output stops immediately after turning off the switch) -

10-12
2) EBD (Electronic Brake-force Distribution) Warning Lamp
EBD warning lamps (brake warning lamp and ABS warning lamp) come on when the system
performs the self diagnosis and when it detects the malfunction of EBD system. However, the
brake warning lamp comes on regardless of EBD system when the parking brake is applied.
EBD warning lamp ON:
When turning the ignition switch to ON position, ABS warning lamp and the brake warning
lamp comes on for 3 seconds for self diagnosis and goes off if the system is OK
(initialization mode).
When applying the parking brake, the brake warning lamp comes on.
When the brake fluid is not sufficient, the brake warning lamp comes on.
When disengaging the connector, the warning lamp comes on.
When the system is defective, ABS warning lamp and the brake warning lamp come on
simultaneously. A.
B.
C.
D.
E.
When the solenoid valve is defective
When one or more wheel sensors are defective
When ABS HECU is defective
When the voltage is abnormal
When valve relay is defective a.
b.
c.
d.
e.
When the communication between warning lamp CAN modules in meter cluster is failed,
the warning lamp comes on. F.

11-114890-10
2) EBD (Electronic Brake-force Distribution) Warning Lamp (Brake
Warning Lamp)
EBD warning lamp when the system perform the self diagnosis and when it detects the
malfunction of EBD system. However, the brake warning lamp comes on regardless of EBD
when the parking brake is applied.
EBD warning lamp ON:
When turning the ignition switch to ON position, ABS warning lamp and the brake warning
lamp comes on for 3 seconds for self diagnosis and goes off if the system is OK
(initialization mode).
When applying the parking brake, the brake warning lamp comes on.
When the brake fluid is not sufficient, the brake warning lamp comes on.
When disengaging the connector, the warning lamp comes on.
When the system is defective, ABS warning lamp and the brake warning lamp come on
simultaneously. 1.
2.
3.
4.
5.
When the solenoid valve is defective
When one or more wheel sensors are defective
When ABS HECU is defective
When the voltage is abnormal
When valve relay is defective a.
b.
c.
d.
e.
When the communication between warning lamp CAN module in meter cluster, the
warning lamp comes on. 6.
3) ESP OFF Indicator
ESP OFF indicator ON:
When turning the ignition switch to ON position, ESP warning lamp comes on for 3 seconds for
self diagnosis and goes off if the system is OK (initialization mode).
When the ESP OFF switch is pressed to turn off ESP function, ESP OFF indicator comes on. 1.
2.
4) ESP Warning Lamp
ESP warning lamp ON:
When turning the ignition switch to ON position, ESP warning lamp comes on for 3 seconds
for self diagnosis and goes off if the system is OK (initialization mode).
When the system is defective, the warning lamp comes on.
When the ESP function is activated, ESP warning lamp blinks with the interval of 2 Hz.
When the communication between warning lamp CAN module in meter cluster, the warning
lamp comes on. 1.
2.
3.
4.
5.
5) ESP OFF Switch
If ESP OFF switch is pressed, ESP function is deactivated and the ESP OFF indicator in the
instrument cluster comes on.
To resume the ESP function, press the switch again. At this time, ESP OFF indicator goes out.