key SUBARU LEGACY 2008 4.G Navigation Manual

25
3
Select the method you want to use.
(Address)* See Page 26.
(Point of Interest)* See Page 32.
(Select from Map) See Page 35.
(Emergency) See Page 38.
(Memory Point) See Page 29.
(Previous Destination) See Page 34.
(Intersection)* See Page 42.
(Freeway Ent/Exit) See Page 36.
(Phone number) See Page 44.
(Coordinates) See Page 40.
(Home) See Page 31.
You can switch between screens by selecting (next page) or (previous page).
NOTE
• If the set destination area is different from the one displayed under “Search Area” in the right part of the screen, you must select the
(change) key and specify the desired area again.
• For the methods marked with an asterisk ( * ), you can use the “Change Search Area” function to narrow the area where a destination
or waypoint is located by selecting the (change) key (see Page 46).
• Depending on the method used or the status of the map displayed, the located point may differ from where the facility you want to
visit actually exists.
Setting Route

26
Setting Route
■“Address” method1
Enter a house number using the keypad on the house number input
screen and select .
2
Enter the street name.If you enter enough letters to identify a street name and advance to Step 3, a list
showing several street names will be displayed. Select the desired street name from
the list.
:Use this key to delete the last character entered. Select it repeatedly if you
want to delete all the characters entered.
You can switch between keypad screens showing different characters by selecting
(others), (symbols) or (alphabet).
First, choose either of the two procedures below to follow the “address” method.
• Press the button or select , select (destination entry), and then select (address).
• Press the button and select (address).

27
3
Select (list).
4
Select the desired street from the list.If the same street name exists in more than one city, a list of these cities will be
shown.
5
Select the correct city from the list.
:Use this key to input the city name from the keypad.
Setting Route

29
■“Memory Point” methodIf you have saved some locations in the system’s memory, you can make use of an appropriate one to set the
destination.1
Select the category to which the address of the desired location
(memory point) is classified in the memory.
2
Select the address of the desired location (memory point).
:Use this key to display up to five previous suggestions.
:Use this key to display the previous suggestion.
:Use this key to display the next suggestion.
:Use this key to display up to five of the next suggestions.
Setting Route
First, choose either of the two procedures below to follow the “memory point” method.
• Press the button or select , select (destination entry), and then select (memory point).
• Press the button and select (memory point).

30
Setting Route
3
Select (destination) or (waypoint).
NOTE• Select the (destination), (icon), (name), or (date) key to change the sequence in which memory points are
displayed.
• You cannot use the “Memory Point” method unless there are memory points stored. To store memory points, see Page 89.

31
■“Home” method or method using stored destinationsIf you have stored your home address in the system’s memory, you can use it for your destination or a waypoint.
Similarly, if other locations are stored in the memory, they can be conveniently used for quick setting of destination
and waypoints.1
Select (home) or one of the locations programmed to keys
through .The map including your home location or the selected location will be displayed.
2
Select (destination) or (waypoint).
NOTEIcon (home) and keys through are displayed only when you have stored your home location and other locations in the
memory. For instructions on how to store your home location and other locations, see Page 100.
Setting Route
First, choose either of the two procedures below to follow the “home” method.
• Press the button or select , select (destination entry).
• Press the button.

32
Setting Route
■“Point of Interest” methodYou can use a selection from the “Point of Interest” listing as your destination or a waypoint.1
Enter the name of the desired point of interest and select .
2
Select the desired point of interest from the list.
:Use this key to display up to five previous suggestions.
:Use this key to display the previous suggestion.
:Use this key to display the next suggestion.
:Use this key to display up to five of the next suggestions.
First, choose either of the two procedures below to follow the “point of interest” method.
• Press the button or select , select (destination entry), and then select (point of interest).
• Press the button and select (point of interest).

34
Setting Route
■“Previous Destination” methodThis method allows you to choose one of the most recently used 100 destinations or waypoints as your new
destination or waypoint.1
Select a desired location from the Previous Destination list.
:Use this key to display up to five previous suggestions.
:Use this key to display the previous suggestion.
:Use this key to display the next suggestion.
:Use this key to display up to five of the next suggestions.
2
Select (destination) or (waypoint).
NOTEYou can select (name) or (date) to change the sequence in which previous destinations are displayed.First, choose either of the two procedures below to follow the “previous destination” method.
• Press the button or select , select (destination entry), and then select (previous
destination).
• Press the button and select (previous destination).

36
Setting Route
■“Freeway Entrance/Exit” methodYou can use the name of a freeway entrance or exit selected from the “Freeway Entrance/Exit” list for setting your
destination or a waypoint.1
Enter the name of the desired freeway and select .
2
Select the name of the freeway from the list.
:Use this key to display up to five previous suggestions.
:Use this key to display the previous suggestion.
:Use this key to display the next suggestion.
:Use this key to display up to five of the next suggestions.
First, choose either of the two procedures below to follow the “freeway entrance/exit” method.
• Press the button or select , select (destination entry), and then select (freeway
entrance/exit).
• Press the button and select (freeway entrance/exit).

37
3
Select (entrance) or (exit).
4
Select the name of the street from which you will enter the freeway or
to which you will go after leaving the freeway.
:You must select this key before you can enter the street name.
:Use this key to search through the list by distance.
:Use this key to search through the list by name (alphabetical search).
5
Select (destination) or (waypoint).
Setting Route