TOYOTA AVALON 2001 Service Repair Manual
Page 441 of 1897
BO2QH-01
- BODYREAR SEAT
BO-123
1908 Author: Date:
2001 AVALON (RM808U)
INSTALLATION
Installation is in the reverse order of removal (See page BO-123).
Page 442 of 1897
BO2QG-01
BO-122
- BODYREAR SEAT
1907 Author: Date:
2001 AVALON (RM808U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page BO-121).
Page 443 of 1897
BO2QE-01
H13186
H12220
BO-120
- BODYREAR SEAT
1905 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR SEAT CUSHION ASSEMBLY
Remove the rear seat cushion.
2. REMOVE REAR SEATBACK ASSEMBLY
(a) Remove the 4 bolts.
Torque:
Center: 41 N´m (420 kgf´cm, 30 ft´lbf)
LH, RH Side: 18 N´m (185 kgf´cm, 13 ft´lbf)
(b) Raise the seatback assembly upward to remove the seat-
back assembly.
Page 444 of 1897
BO2PZ-01
H12201
Roof Headlining
Roof Side Inner Garnish
Front Seat Outer
Belt Floor Anchor
Front Door
Opening Trim Assist Grip
w/ Rear personal light:
Rear Personal Light
Roof
Console
Box
Map Light Lens
Assist Grip
Sun Visor
Holder
Front Pillar Garnish
Front Door Scuff
Inside Plate
Center Pillar GarnishLensRoom Light
RH Rear Seat Inner
with Center Belt
Rear Door
Opening Trim
Lower Center
Pillar GarnishInside Rear Door
Scuff Plate
Rear Seatback
LH Rear Seat Inner
with Center Belt
Rear Seat Cushion
w/ Sliding roof:
Roof HeadliningSliding Roof
Opening Trim
41 (420, 30)
Lap Belt Outer Anchor Cover
41 (420, 30)
18 (185, 13)
18 (185, 13)
41 (420, 30)
: Specified torqueN´m (kgf´cm, ft´lbf)Cover
Cover
BO-98
- BODYROOF HEADLINING
1883 Author: Date:
2001 AVALON (RM808U)
ROOF HEADLINING
COMPONENTS
Page 445 of 1897
BO2Q1-01
BO-102
- BODYROOF HEADLINING
1887 Author: Date:
2001 AVALON (RM808U)
INSTALLATION
Installation is in the reverse order of removal (See page BO-99).
Page 446 of 1897
BO2Q0-01
H12197
H12128
: 7 Clips
H12161
Claw
Claw
- BODYROOF HEADLINING
BO-99
1884 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR SEAT (See page BO-120)
2. REMOVE INSIDE REAR DOOR SCUFF PLATE
(a) Remove the clip.
(b) Remove the inside rear door scuff plate as shown in the
illustration.
(c) Employ the same manner described above to the other
side.
3. REMOVE REAR DOOR OPENING TRIMS
4. REMOVE ROOF SIDE INNER GARNISH
(a) Using a screwdriver, remove the roof side inner garnish.
HINT:
Tape the screwdriver tip before use.
(b) Employ the same manner described above to the other
side.
5. REMOVE ASSIST GRIPS
(a) Using a screwdriver, remove the cover.
HINT:
Tape the screwdriver tip before use.
(b) Loosen bolts until assist grip detaches from the vehicle.
(c) Repeat at 4 positions.
6. w/ Rear personal light:
REMOVE REAR PERSONAL LIGHT
(a) Using a screwdriver, remove the rear personal light, then
disconnect the connector.
HINT:
Tape the screwdriver tip before use.
(b) Employ the same manner described above to the other
side.
Page 447 of 1897
H12175
H12198
H12199
:5 Clips
H12200Clip
H121452 Clips BO-100
- BODYROOF HEADLINING
1885 Author: Date:
2001 AVALON (RM808U)
7. REMOVE FRONT DOOR SCUFF INSIDE PLATE
(a) Remove the front door scuff inside plate.
(b) Employ the same manner described above to the other
side.
8. REMOVE FRONT DOOR OPENING TRIMS
9. REMOVE LOWER CENTER PILLAR GARNISH
(a) Using a screwdriver, remove the lap belt outer anchor
cover.
(b) Remove the front seat outer belt floor anchor.
Torque: 41 N´m (420 kgf´cm, 30 ft´lbf)
(c) Remove the lower center pillar garnish as shown in the il-
lustration.
(d) Employ the same manner described above to the other
side.
10. REMOVE CENTER PILLAR GARNISH
(a) Remove the 2 clips.
(b) Using a screwdriver, remove the center pillar garnish.
HINT:
Tape the screwdriver tip before use.
(c) Employ the same manner described above to the other
side.
11. REMOVE FRONT PILLAR GARNISH
(a) Remove the front pillar garnish.
(b) Employ the same manner described above to the other
side.
Page 448 of 1897
H12144
H121623 Clips
- BODYROOF HEADLINING
BO-101
1886 Author: Date:
2001 AVALON (RM808U)
12. REMOVE ROOF CONSOLE BOX
(a) Using a screwdriver, remove the map light lens.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 3 screws and roof console box, then discon-
nect the connector.
13. REMOVE ROOM LIGHT
(a) Using a screwdriver, remove the room light lens.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 4 screws and room light, then disconnect the
connector.
14. w/ Sliding roof:
REMOVE SLIDING OPENING TRIM
15. REMOVE SUN VISORS AND HOLDERS
(a) Using a screwdriver, pry the bracket cover off from the
rear.
(b) Remove the 2 screws from the visor bracket and a screw
from the holder.
(c) Remove the visor assembly from the holder and discon-
nect the connector.
(d) Pull off the holder.
16. REMOVE ROOF HEADLINING
Disengage the 3 clips and remove the roof headlining.
Page 449 of 1897
BO2PD-01
H12142
Rocker Panel Moulding BO-54
- BODYROCKER PANEL MOULDING
1839 Author: Date:
2001 AVALON (RM808U)
ROCKER PANEL MOULDING
COMPONENTS
Page 450 of 1897
BO2QM-01
AB0152
SST
- BODYSEAT BELT PRETENSIONER
BO-131
1916 Author: Date:
2001 AVALON (RM808U)
DISPOSAL
HINT:
When scrapping vehicles equipped with a seat belt pretension-
er or disposing of a front seat outer belt (with seat belt preten-
sioner) always first activate the seat belt pretensioner in accor-
dance with the procedure described below. If any abnormality
occurs in the seat belt pretensioner operation, contact the SER-
VICE DEPT. of TOYOTA MOTOR SALES, U.S.A., INC. When
disposing of a front seat outer belt (with seat belt pretensioner)
activated in a collision, follow the same procedure given in step
1-(e) in ºDISPOSALº.
CAUTION:
Never dispose of the front seat outer belt which has
an inactivated pretensioner.
The seat belt pretensioner produces a sizeable ex-
ploding sound when it activates, so perform the op-
eration out-of-door and where it will not create a nui-
sance to nearby residents.
When activating the seat belt pretensioner, always
use the specified SST. (SRS Airbag Deployment Tool)
Perform the operation in a place away from electrical
noise.
SST 09082-00700, 09082-00740
When activating a front seat outer belt (with seat belt
pretensioner), perform the operation at least 10 m (33
ft) away from the front seat outer belt.
Use gloves and safety glasses when handling a front
seat outer belt with activated pretensioner.
Always wash your hands with water after completing
the operation.
Do not apply water, etc. to a front seat outer belt with
the activated pretensioner.