TOYOTA CAMRY 1999 Service Repair Manual

Page 321 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±15
10. REMOVE MANUAL VALVE BODY
(a) Remove the 2 bolts and detent spring.
(b) Remove the 5 bolts and manual valve body with the
manual valve.
(c) Remove the manual valve from the manual valve body.
11. REMOVE OIL PIPES
(a) Remove the bolt.
(b) Pry up both pipe ends with a large screwdriver and re-
move the 6 pipes.
12. DISCONNECT SOLENOID CONNECTORS
13. REMOVE CONNECTOR CLAMP AND PIPE RETAINER

Page 322 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±16
14. REMOVE B3 APPLY PIPE
Pry up the pipe with a screwdriver and remove the pipe.
15. REMOVE VALVE BODY
(a) Remove the 9 bolts.
(b) Remove the wire harness clamp.
(c) Disconnect the throttle cable from the cam, and remove
the valve body.
16. REMOVE THROTTLE CABLE

Page 323 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±17
17. REMOVE SOLENOID WIRING
Remove the bolt and the solenoid wiring.
18. REMOVE SECOND BRAKE APPLY GASKET
19. REMOVE ACCUMULATOR PISTONS AND SPRINGS
(a) Loosen the 4 bolts one turn at a time until the spring ten-
sion is released.
(b) Remove the cover and gasket.
(c) Remove the C
1 accumulator piston and spring.
(d) Remove the 2 O±rings from the piston.
(e) Pop out pistons for C
2 and B2 into a rag, using low±pres-
sure compressed air (98 kPa, 1 kgf/cm
2, 14 psi).
(f) Remove the O±rings from the pistons.

Page 324 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±18
20. MEASURE PISTON STROKE SECOND COAST
BRAKE
(a) Apply a small amount of paint to the piston rod at the point
it meets the case.
(b) Using SST, measure the piston stroke while applying and
releasing compressed air (392±785 kPa, 4±8 kgf/cm
2,
57±114 psi).
SST 09240±00020
Maximum thrust clearance:
2.0±3.5 mm (0.079±0.138 in.)
If the piston stroke exceeds the limit, inspect the second
coast brake band.
21. REMOVE SECOND COAST BRAKE PISTON
(a) Using SST, remove the snap ring.
SST 09350±32014
(b) Applying compressed air to the oil hole, remove the se-
cond coast brake cover, piston assembly and spring.
(c) Remove the 2 O±rings from the cover.

Page 325 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±19
22. STAND TRANSAXLE ENGINE SIDE UPWARD
23. REMOVE OIL PUMP
NOTICE: Before removing the oil pump, remove the se-
cond coast brake piston.
(a) Remove the 7 bolts.
(b) Using SST, pull out the oil pump from the transaxle case.
SST 09350±32014
24. REMOVE O±RING FROM OIL PUMP
25. REMOVE DIRECT CLUTCH AND FORWARD CLUTCH
26. SEPARATE DIRECT CLUTCH AND FORWARD
CLUTCH
(a) Separate the direct clutch and forward clutch.
(b) Remove the thrust washer from direct clutch.

Page 326 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±20
27. REMOVE BEARING FROM FORWARD CLUTCH
28. REMOVE SECOND COAST BRAKE BAND
(a) Push the pin with a small screwdriver and remove it from
the bolt hole of the oil pump mounting.
(b) Remove the brake band.
29. REMOVE FRONT PLANETARY RING GEAR
30. REMOVE FRONT PLANETARY GEAR
(a) Remove the front planetary gear.
(b) Remove the 2 bearings from the planetary gear.

Page 327 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±21
31. REMOVE SUN GEAR AND SUN GEAR INPUT DRUM
(a) Remove the sun gear and the sun gear input drum.
(b) Remove the thrust washer from sun gear input drum.
32. CHECK OPERATION OF SECOND BRAKE PISTON
Apply compressed air into the case passage and confirm
that the piston moves.
If the piston does not move, disassembe and inspect.
33. REMOVE SECOND COAST BRAKE BAND GUIDE
34. REMOVE SECOND BRAKE DRUM
(a) Remove the snap ring.

Page 328 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±22
(b) Remove the second brake drum.
35. REMOVE SECOND BRAKE PISTON RETURN SPRING
36. REMOVE NO.1 ONE±WAY CLUTCH
37. REMOVE PLATES, DISCS AND FLANGE
38. REMOVE SECOND BRAKE DRUM GASKET
Remove the gasket.

Page 329 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±23
39. REMOVE NO.2 ONE±WAY CLUTCH AND REAR PLAN-
ETARY GEAR
(a) Remove the snap ring.
(b) Remove the No.2 one±way clutch and rear planetary
gear.
(c) Remove the thrust washer from the rear planetary gear.
40. REMOVE REAR PLANETARY RING GEAR
(a) Remove the rear planetary ring gear.
(b) Remove the bearing from the ring gear.
41. CHECK FIRST AND REVERSE BRAKE
(a) Check the operation of the first and reverse brake piston.
Apply compressed air into the case passage and confirm
that the piston moves.
If the piston does not move, disassemble and inspect.

Page 330 of 4592

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±24
(b) Using a filler gauge, check the pack clearance of the first
and reverse brake.
Clearance: 1.92±2.68 mm (0.0756±0.1055 in.)
42. REMOVE FLANGE, DISCS AND PLATES OF FIRST
AND REVERSE BRAKE
(a) Remove the snap ring.
(b) Remove the flange, 6 discs and plates.
43. TURN TRANSAXLE CASE AROUND
44. REMOVE OVERDRIVE UNIT
(a) Remove the 13 bolts.
(b) Tap on the circumference of the overdrive case with a
plastic hammer to remove the overdrive case and gasket.

Page:   < prev 1-10 ... 281-290 291-300 301-310 311-320 321-330 331-340 341-350 351-360 361-370 ... 4600 next >