TOYOTA CAMRY 2000 Service Repair Manual

Toyota Supports ASE CertificationPage 1 of 2
BO015±00
Title:
DOOR MIRROR INSTALLATION
Models:
'97 ± '00 Japan Built Camry
Technical Service
BULLETIN
March 24, 2000

The procedures in this bulletin explain in detail how to install the door mirrors.
CAUTION:
If the door mirror is installed incorrectly, a wind noise (air leakage noise) might be
generated.
1997 ± 2000 model year Japan built Camry
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
1. Remove the retaining clip and
speaker (if applicable) from the door.
Discard the removed clip.
2. In order to secure the door mirror in
the correct position, insert the 2 pins
of the door mirror base into the holes
of the door.
3. Push the door mirror against the door
and check that the door mirror base
edge is in contact with the door frame
molding lip.
NOTE:
This area is critical to wind noise
reduction.
BODY
Introduction
Applicable
Vehicles
Warranty
Information
Installation
Procedure
Clip
Speaker
Pins
Molding Lip
Mirror Base

DOOR MIRROR INSTALLATION ± BO015-00 March 24, 2000
Page 2 of 2
4. For vehicles without a speaker,
tighten the three mirror mounting nuts.
Torque: 5.5 Nm (56 kgfcm, 49 inlbf)
Connect the mirror wire.
5. For vehicles with a speaker, tighten
the two mirror mounting nuts.
Torque: 5.5 Nm (56 kgfcm, 49 inlbf)
Connect the mirror wire.
While lightly pulling the mirror wire
backward, reinstall the door speaker (one
nut at the lower bracket) onto the door as
shown in the illustration.
Torque: 5.5 Nm (56 kgfcm, 49 inlbf)
NOTE:
Do NOT mount the upper speaker
bracket behind the nut.
6. Check the following items:
There is no clearance between
the door mirror base and the door
molding lip.
The mirror wire is free from the
speaker bracket.
The door frame molding lip is not
tucked under the mirror base.
The speaker wire does not
contact the mirror mounting
screw.
Make sure the power mirror
adjustment and the door speaker
functions properly.
7. Install the front door lower frame
bracket garnish/speaker cover.
8. Install the black cap onto the nut.
Installation
Procedure
(Continued)Mounting
Nuts
Mounting
Nuts
Speaker
INCORRECTCORRECT
Mounting Lip
Mirror Base
Speaker Cover
Garnish
Cap

Toyota Supports ASE CertificationPage 1 of 2
BO017-01Title:
POWER SEAT MOTOR CABLE REPAIR TIP
Models:
'99 ± '00 Camry & Solara, '99 ± '01 Sienna
Technical Service
BULLETIN
May 25, 2001

TSB REVISION NOTICE:
June 25, 2003: The Parts Information table has been updated.
The previous TSB should be discarded.
A field fix has been developed to repair loose power seat motor cables (instead of seat
adjuster replacement). Loose cables can cause seat movement feel or no movement of
seat adjustment.
1999 ± 2000 model year Camry and Solara vehicles.
1999 ± 2001 model year Sienna vehicles.
3M PART NUMBERPART NAMEQUANTITY
3M 365963M EPS±300 Thin±Wall1 Per Seat Motor
TOOLS & MATERIALSQUANTITY
Heat Gun1
OP CODEDESCRIPTIONTIMEOPNT1T2
BD1017R & R Seat Assembly;
Install Shrink Sleeves0.5
72020±06020 (Solara)
72020±AA011 (Camry
72020±08010 (Sienna)
9515
Applicable Warranty*:
This repair is covered under the Toyota Comprehensive Warranty. This warranty is in
effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's
in-service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Parts
Information
Required
Tools &
Material
Warranty
Information

POWER SEAT MOTOR CABLE REPAIR TIP ± BO017-01 Revised May 25, 2001
Page 2 of 2
1. Remove the seat assembly from the
vehicle.
Turn the seat over and detach motors
from the mounting brackets.
NOTE:
The lower seat cushion must be
removed from the seat frame to access
the motor mounting screws on some
models.
2. Remove the drive cable from the motor gear boxes. Slide a shrink wrap tube
(3/4º diameter x 1.75º, 3M P/N 36596) on each end of the flex shaft, as shown in
the illustration.
The Camry and Sienna will require six (6) shrink tubes.
The Solara will require only one (1) shrink tube.
Camry/Sienna Solara
Front
3. Attach the drive cables to the motors and reinstall motors to the motor mounts.
4. Position each shrink wrap tube so that it overlaps the drive cable housing and motor
housing or gear box housing, as necessary.
5. Using a heat gun, apply heat to the
shrink tubes in a direction from the
center of the drive cable toward the
gear box or motor housing. Be sure to
apply just enough heat to shrink the
tubing.
6. Reinstall the seat cushion to the seat
frame. Tighten the mounting screws to
torque specifications listed in the BO
section of the Repair Manual.
7. Reinstall the seat assembly to the
floor of the vehicle. Assure all
connectors are secure and the power
seat adjustments properly function.
Torque: 37 Nm, 380 kgfcm, 27 ftlbs
Repair
Procedure
Heat Gun
Shrink Tube

Toyota Supports ASE CertificationPage 1 of 1
BO017-03Title:
TRIM GARNISH LOOSE
Models:
All Models
Technical Service
BULLETIN
September 9, 2003

TSB REVISION NOTICE:
March 3, 2004: The TSB has been changed to include new inspection and
replacement instructions.
Previous versions of this TSB should be discarded.
Customers may experience an interior trim panel either loose or fitting poorly due to a
deformed or missing panel attachment clips. When a trim garnish (A, B, C or D pillar
garnish, door trim panel, etc.) is removed and reinstalled using the old clips, there is a
possibility that the garnish may exhibit a loose condition. To prevent this condition from
occurring, please use the following procedures.
All Models ± All trim panel attachment clips must be inspected prior to reassembly and
replaced if any damage or wear is detected. If no damage is visible, the clip may be
reused. Always check to make sure that the garnish is properly attached after
reinstallation of all interior trim panels.
2002 ± 2004 model year Camry and 2004 model year Solara ± When removing the
A±pillar garnish panels, replace the white plastic attachment clips (P/N 90467±A0025).
All models.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
BODY
Introduction
Inspection/
Replacement
Procedure
Applicable
Vehicles
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 2
BO017±99
Title:
DOOR GLASS DISPLACEMENT
Models:
'98 ± '99 TMMK Camry
Technical Service
BULLETIN
November 26, 1999

On some 1998 and 1999 Camry vehicles, the door glass may be displaced from the front
door glass run if the door is closed forcefully with the window partially down. A field fix
has been developed to remedy this condition.
1998 ± 1999 TMMK Camrys vehicles produced prior to VINs listed below.
MODELSTARTING VIN
1999 TMMK produced Camry
4T1BG**K*XU602813
4T1BF**K*XU088877
4T1BG**K*XU917744
4T1BF**K*XU933406
NOTE:
Refer to 1998 Camry Repair Manual (Vol. 2) BO±Section for Door Panel Removal and
Window Regulator Servicing information.
OP CODEDESCRIPTIONTIMEOPNT1T2
BD9008R&R Door Trim / Modify Hole (both sides)0.567402±AA0115357
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Production
Change
Information
Warranty
Information

DOOR GLASS DISPLACEMENT ± BO017±99 November 26, 1999
Page 2 of 2
1. Lower the door glass, disconnect the power window switch, remove the front door
trim panel, speaker, and loosen the door mirror mounts to gain access to the door
glass and lower frames. Remove the front lower frame (2 screws).
2. Locate the lower window frame mounting hole on the door (see illlustration). Place a
towel or shop rag in the speaker hole to catch metal chips. Using a round file or die
grinder, enlarge the hole 2 mm toward the speaker (rear of the vehicle). Remove the
towel or shop rag and any metal chips in the door. Apply touch±up paint or rust
preventative to the hole.
2 mm"u
3. Install a rubber stopper to the lower window frame according to directions in TSB
BO012±99.
4. Install the lower window frame. Assure the frame is tight against the glass and the
run is fully inserted in the lower window frame channel.
5. Temporarily connect the power window switch and operate the window. Check to
assure the door glass fully opens and closes easily.
6. Reinstall the door panel and components, check lock/unlock function and door
opening handle function.
Repair
Procedure

Toyota Supports ASE CertificationPage 1 of 2
BO019±99
Title:
DOOR MIRROR WIND NOISE
Models:
'97 ± '99 Camry
Technical Service
BULLETIN
December 3, 1999

Wind/road noise heard around the door mirrors of some Japan produced Camry vehicles
may be caused by an improperly positioned mirror wire harness grommet and/or harness
connector.
1997 through 1999 Camry vehicles. (Japan produced only)
PLANTSTARTING VIN
TMC
JT2BG22K * X0367325
JT2BG28K * X0367352
TMCJT2BG28K X0367352
JT2BF22K * X0227381
JT2BF28K * X0227306
OP CODEDESCRIPTIONTIMEOPNT1T2
BD9006Adjust the Wire Harness Grommet
and/or Connector (both sides)0.487910±331505957
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
1. Carefully pry off the door speaker
cover and remove the nut using a 10
mm socket that secures the speaker
to the door.
2. Look through the door mirror harness
access hole and check the position of
the wire harness grommet and wire
harness connector ± the harness
connector should be inside the
grommet and the grommet should be
fully seated in the mirror housing.
BODY
Introduction
Applicable
Vehicles
Production
Change
Information
Warranty
Information
Connector
and Grommet
Mirror Housing
Grommet Connector
CORRECT POSITION
Repair
Procedure

DOOR MIRROR WIND NOISE ± BO019±99 December 3, 1999
Page 2 of 2
INCORRECT POSITION A INCORRECT POSITION B INCORRECT POSITION C
Mirror Housing
ConnectorGrommetMirror Housing
Mirror Housing
Grommet Grommet
ConnectorConnector
3. To reposition the grommet and/or
harness connector onto the mirror
housing:
Remove the mirror housing (3
nuts) from the door and carefully
unclip the mirror from the housing.
This will allow easier access and
reinstallation of the grommet
and/or harness connector.
Reposition the grommet so it is
fully seated to the mirror housing.
Assure the harness connector is
inside the grommet.
NOTE:
Refer to the 1998 Camry Repair Manual
pages BO±23 through BO±26.
4. Reinstall the door mirror and speaker
assembly:
Secure the mirror to the housing.
Properly align and reinstall the
mirror assembly to the door.
tighten the three nuts. Torque:
5.5 Nm (56 Kgfcm, 49 inlb)
Reinstall the door speaker (one
nut) and speaker cover onto the
door.
Assure the power mirror
adjustment and the door speaker
functions properly.
ConnectorRear View MirrorOutside Door
Mirror
Mirror Housing
Grommet
CORRECT POSITION
Repair
Procedure
CoverOutside Rear
View Mirror
Door Trim
Specified Torque Nm (kgfcm, ftlbf) :5.5 (55, 49, ftlbf)

Toyota Supports ASE CertificationPage 1 of 7
BO020±98
Title:
1999 TOYOTA SEAT BELT EXTENDERS
Models:
All '95 through '99 model years
Technical Service
BULLETIN
July 3, 1998

Toyota customers who find it necessary to
increase the length of their seat belts may
obtain Seat Belt Extenders at no cost
through their local Toyota dealer.
The extender is available in 6 inch, 9 inch,
12 inch, 15 inch and 18 inch lengths.
The extender is available only in black.
Owners are informed of the seat belt
extender availability through the Toyota
Owner 's Manual included in each vehicle.
The customer
(individual requiring the extender) must visit a Toyota dealership to have
the required measurements made and to complete the seat belt extender worksheet.
The worksheet will allow the proper fitting and selection of a seat belt extender for the
customer. The dealership personnel should then determine the applicable part number
and place a
Critical Order through the TDN Parts Network.
The dealership service department should complete the affixed Seat Belt Extender Label
and review the ªowner instruction sheetº with the customer. The dealership should give a
copy of the completed worksheet to the customer and keep the original in the customer's
file.
To assure utmost owner satisfaction, it is recommended that a dealership designate one
person to coordinate all activities related to the seat belt extender issue.
From past sales history, it is recommended that dealerships do not stock Seat belt
extenders due to low demand and the need for customer fitting.
This bulletin contains the following information:
Procedure and Flow Chart...................... Page 2
Application Chart and Notes.................. Page 3
Part Number Information........................ Page 5
Owner Instructions.................................. Page 6
Seat Belt Extender Worksheet............... Page 7
All Toyota models, 1995 through 1999 model years.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
BODY
Introduction
Extender Seat Belt
Affected
Vehicles
Warranty
Information