TOYOTA LAND CRUISER 1996 J80 Workshop Manual

SA−78
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
935
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA24T−01
SA2310
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−79
1996 LAND CRUISER (RM451U)
REMOVAL
1. w/ Differential lock:
SHIFT REAR DIFFERENTIAL TO LOCK
(a) Turn the ignition switch to the ON position.
(b) Keep the center differential lock condition.
(c) Turn the differential lock control switch to the RR or FR/ RR position and lock the rear differential.
HINT:
Rotating the tires, check they are in the differential lock condi-
tion.
(d) Disconnect the cable from the negative terminal of the battery.
2. DRAIN DIFFERENTIAL OIL
3. REMOVE REAR AXLE SHAFTS (See page SA−63 )
4. DISCONNECT PROPELLER SHAFT (See page PR−3 )
5. REMOVE DIFFERENTIAL CARRIER ASSEMBLY
(a) Remove the 10 nuts, washers and differential carrier as- sembly.
NOTICE:
Be careful not to damage the installation surface. Torque: 73 N·m (740 kgf·cm, 54 ft·lbf)
(b) Remove the gasket.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W00493
30 mm
(1.18 in.)
SA1VH−04
SA2446
SA−80
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. CHECK RUNOUT OF COMPANION FLANGE
Using a dial indicator, measure the vertical and lateral runout of
the companion flange. Maximum runout: 0.10 mm (0.0039 in.)
2. CHECK RING GEAR RUNOUT
Using a dial indicator, measure the ring gear runout. Maximum runout: 0.10 mm (0.0039 in.)
If the runout is greater than the maximum, replace the ring gear.
3. CHECK RING GEAR BACKLASH
Using a dial indicator, measure the ring gear backlash. Backlash: 0.15 − 0.20 mm (0.0059 − 0.0079 in.)
HINT:
Perform the measurements at 3 or more positions around the
circumference of the ring gear.
If the backlash is not within the specification, adjust the side
bearing preload or repair as necessary.
4. MEASURE DRIVE PINION PRELOAD
(a) Using a torque wrench, measure the preload of backlash between the drive pinion and ring gear.
Preload (at starting):
0.7 − 1.0 N·m (7 − 10 kgf·cm, 6.1 − 8.7 in.·lbf)
(b) Using a torque wrench, measure the preload. Total preload (at starting):
Drive pinion preload plus
w/o Differential lock
0.4 − 0.6 N·m (4 − 6 kgf·cm, 3.5 − 5.2 in.·lbf)
w/ differential lock
0.3 − 0.7 N·m (3 − 7 kgf·cm, 2.6 − 6.1 in.·lbf)
If necessary, disassemble and inspect the differential.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2131
SA2134
SA2448
SST
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−81
1996 LAND CRUISER (RM451U)
5. CHECK SIDE GEAR BACKLASH
Using a dial indicator, measure the side gear backlash with
holding one pinion gear toward the case.
Backlash: 0.02 − 0.20 mm (0.0008 − 0.0079 in.)
If the backlash is not within the specification, install the correct
thrust washers (See page SA−87).
6. CHECK TOOTH CONTACT BETWEEN RING GEAR
AND DRIVE PINION (See page SA−35 )
7. w/ DIFFERENTIAL LOCK: REMOVE INDICATOR SWITCH
Remove the indicator switch and gasket.
8. w/ DIFFERENTIAL LOCK: REMOVE COVER
(a) Remove the 3 bolts.
(b) Using a brass bar and hammer, tap on the cover to re- move it.
9. w/ DIFFERENTIAL LOCK: REMOVE SLEEVE
(a) Remove the 4 bolts.
(b) Using a plastic hammer, tap the actuator.
(c) Remove the actuator and sleeve.
10. w/ DIFFERENTIAL LOCK: REMOVE ACTUATOR AND SHIFT FORK AND SHAFT
(a) Remove the shift fork shaft bolt.
(b) Pull out the actuator and remove the shift fork.
11. REMOVE COMPANION FLANGE
(a) Using a chisel and hammer, unstick the nut.
(b) Using SST to hold the flange, remove the nut and plate washer.
SST 09330−00021
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13166
SST
SA2348
SST
Z00641
SST
SSTSST
SA−82
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
(c) Using SST, remove the companion flange.
SST 09950 −30010 (09951 −03010, 09953 −03010,
09954 −03010, 09955 −03030, 09956−03020)
12. REMOVE OIL SEAL AND OIL SLINGER
(a) Using SST, remove the oil seal from the dif ferential carrier.
SST 09308−10010
(b) Remove the oil slinger.
13. REMOVE FRONT BEARING
Using SST, remove the front bearing from the drive pinion. SST 09556−22010
If the front bearing is damaged or worn, replace the bearing.
14. w/o DIFFERENTIAL LOCK: REMOVE DIFFERENTIAL CASE ASSEMBLY
(a) Place matchmarks on the bearing cap and dif ferential car-
rier.
(b) Remove the 2 adjusting nut locks.
HINT:
Tag the disassembled parts to show the location for reassemb-
ly.
(c) Remove the 2 bearing caps and adjusting nuts.
(d) Remove the differential case with the bearing outer races
from the carrier.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2437Matchmarks
R08254
SST
Z06911
SST
SA2424
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−83
1996 LAND CRUISER (RM451U)
15. w/ DIFFERENTIAL LOCK:
REMOVE DIFFERENTIAL CASE ASSEMBLY
(a) Place matchmarks on the bearing cap and dif ferential car-
rier.
(b) Remove the 4 bolts and 2 bearing caps.
(c) Using SST, remove the plate washers. SST 09504−22011
HINT:
Measure the plate washer thickness and note it.
(d) Remove the differential case with the side bearing outer races from the differential carrier.
HINT:
Tag the bearing outer races to show the location for reassembly.
16. REMOVE DRIVE PINION AND BEARING SPACER FROM DIFFERENTIAL CARRIER
(a) Remove the drive pinion with the rear bearing.
(b) Remove the bearing spacer.
17. REMOVE DRIVE PINION REAR BEARING
(a) Using SST and a press, remove the rear bearing from the
drive pinion.
SST 09950−00020
HINT:
If the drive pinion or ring gear are damaged, replace them as
a set.
(b) Remove the plate washer from the drive pinion.
18. REMOVE FRONT AND REAR BEARING OUTER
RACES
Using a brass bar and hammer, remove the outer races.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2464
SA−84
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
19. REMOVE RING GEAR
(a) Place matchmarks on the ring gear and differential case.
(b) Remove the 12 ring gear set nuts and bolts.
(c) Using a plastic hammer, tap on the ring gear to remove it
from the differential case.
20. CHECK DIFFERENTIAL CASE RUNOUT
(a) Install the differential case in the differential carrier and tighten the adjusting nut just to where there is no play in
the bearing.
(b) Using a dial indicator, measure the differential case run- out.
Maximum case runout: 0.07 mm (0.0028 in.)
(c) Remove the differential case.
21. w/o DIFFERENTIAL LOCK: REMOVE SIDE BEARINGS FROM DIFFERENTIAL
CASE
Using SST, remove the 2 side bearings from the differential
case. SST 09950 −40010 (09951 −04010, 09952 −04010,
09953 −04020, 09955 −04060, 09957 −04010,
09958 −04010), 09950−60010 (09951 −00480)
22. w/ DIFFERENTIAL LOCK:
REMOVE SIDE BEARINGS FROM DIFFERENTIAL
CASE
(a) Using SST, remove the side bearing (ring gear side). SST 09950 −40010 (09951 −04010, 09952 −04010,
09953 −04020, 09955 −04060, 09957 −04010,
09958 −04010), 09950−60010 (09951 −00480)
HINT:
Fix the claws of SST to the notches in the differential case.
(b) Using SST, 4 bolts and a press, remove the side bearing (cover side).
SST 09550−10012 (09557 −10010),
09950 −70010 (09951 −07150)
HINT:
Fix the claws of SST to the notches in the differential case.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2475
SST
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−85
1996 LAND CRUISER (RM451U)
23. w/o DIFFERENTIAL LOCK:
DISASSEMBLE DIFFERENTIAL CASE
(a) Remove the pinion shaft pin and washer.
(b) Remove these parts from the differential case:
Pinion shaft
2 Pinion gears
2 Pinion gear thrust washers
2 Side gears
2 Side gear thrust washers
24. w/ DIFFERENTIAL LOCK: DISASSEMBLE DIFFERENTIAL CASE
(a) Place matchmarks on the case and cover.
(b) Using a torx socket wrench, remove the 5 set bolts and 3
pinion shaft pins.
(c) Using the 2 cover installation bolts, separate the cover and case.
(d) Remove these parts from the differential case:
2 Side gears
2 Side gear thrust washers
4 Pinion gears
4 Pinion thrust washers
3 Pinion shafts
Pinion shaft holder
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VI−01
SA2419
SST
SA2418SST
SA−86
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE DUST DEFLECTOR
Using SST and a press, remove the dust deflector. SST 09950−00020
2. INSTALL DUST DEFLECTOR
Using SST and a press, install a new dust deflector. SST 09726−40010
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA0510
SA1VJ−04
Z06893
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−87
1996 LAND CRUISER (RM451U)
REASSEMBLY
1. w/o DIFFERENTIAL LOCK:
ASSEMBLE DIFFERENTIAL CASE
(a) Apply all of the sliding and rotating surfaces with gear oil.
(b) Install the 2 thrust washers and side gears. Using the table below, select the thrust washers which will
ensure that the backlash is within the specification.
Try to select washers of the same size for both sides.
Backlash: 0.02 − 0.20 mm (0.0008−0.0079 in.)
Thrust washer thickness
Thickness mm (in.)Thickness mm (in.)
1.60 (0.063)1.90 (0.075)
1.75 (0.069)2.05 (0.081)
(c) Install the side gears with the side gear thrust washers,
pinion gears, pinion gear thrust washers and pinion shaft.
HINT:
Align the hole for the pinion shaft and differential case hole.
(d) Using a dial indicator, measure the side gear backlash with holding the one pinion gear toward the case.
Backlash: 0.02 − 0.20 mm (0.0008 − 0.0079 in.)
If the backlash is not within the specification, install a thrust
washer of different thickness.
(e) Install the pinion shaft pin and washer.
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010