TOYOTA LAND CRUISER 1996 J80 Workshop Manual

SA2621
SA−108
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
1996 LAND CRUISER (RM451U)
(f) Remove the shift fork set bolt.
(g) Remove the 4 bolts.
(h) Using a screwdriver, pry out the actuator.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VO−02
Z07259
Outside
Actuator Installation
Hole Shift Fork
R08154
3
2
1.5
50 °
108 °
Matchmark
(Groove)
SA2306
SA2420
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−109
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL FRONT ACTUATOR
(a) Check that the outermost rack tooth of the shift fork is
virtually above the center line of the actuator installation
hole.
(b) Using a dry cell battery, alig n the matchmark on the pinion
with the center line of the actuator.
NOTICE:
If the pinion of the actuator is not in the specified
place, the actuator is difficult to be installed.
Do not supply the battery positive voltage between
terminals.
If the matchmark comes to the extension limit of the
rotation, do not electrify moreover.
(c) Install a new O−ring to the actuator.
(d) Apply a light coat of gear oil on the O −ring.
(e) Apply MP grease to the gear part of the actuator.
(f) Install the actuator to the differential with the 2 nuts and bolt, so that the outermost rack tooth of the shift fork will
fit matchmark of the pinion of the actuator.
HINT:
Do not damage the O −ring of the actuator.
Torque: 26 N·m (270 kgf·cm, 20 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z15220
FIPG Width Approx.
1 − 2 mm (0.04 − 0.08 in.)
Z07262Adhesive
SA2620
SA−11 0
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
1996 LAND CRUISER (RM451U)
(g) Connect the connector and tube.
HINT:
The depth of the insertion of the bleeder tube into the
hose is approx. 15 mm (0.59 in.).
Take care that water or the equivalent will not adhere to
the connector and hose.
(h) Cancel the front differential lock.
With the ignition switch ON, turn the differential lock con-
trol switch to OFF to cancel the differential lock.
2. INSTALL REAR ACTUATOR
(a) Clean contacting surfaces of any FIPG material using gasoline or alcohol.
(b) Apply FIPG to the actuator. FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
HINT:
Install the actuator within 10 minutes after applying FIPG.
(c) Install the actuator to the differential and match the shaft with the shaft fork hole.
(d) Clean the threads of the set bolt and shaft fork with the white gasoline.
(e) Coat the threads of the set bolt with adhesive.
Adhesive: Part No. 08833 −00070, THREE BOND 1324
or equivalent
(f) Tighten the shift fork set bolt. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
(g) Tighten the 4 bolts uniformly, a little at a time. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
(h) Install the cover. (1) Clean the contacting surfaces of any FIPG material
using gasoline or alcohol.
(2) Apply FIPG to the cover.
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
HINT:
Install the cover within 10 minutes after applying FIPG.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2619
Z07261
−
SUSPENSION AND AXLE DIFFERENTIAL LOCKING SYSTEM
SA−111
1996 LAND CRUISER (RM451U)
(3) Tighten the 3 bolts.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
(i) Install the rear Diff. position switch. Install the position switch with a new gasket.
Torque: 40 N·m (410 kgf·cm, 30 ft·lbf)
(j) Connect the connectors and tube.
HINT:
The depth of the insertion of the bleeder tube into the
hose is approx. 15 mm (0.59 in.).
Take care that the water or the equivalent will not adhere
to the connectors and hose.
(k) Install the actuator protector. Install the protector with the 2 nuts and bolt.
Torque:
Nut: 35 N·m (360 kgf·cm, 26 ft·lbf)
Bolt: 20 N·m (200 kgf·cm, 14 ft·lbf)
(l) Cancel the rear differential lock. With the ignition switch ON, turn the differential lock con-
trol switch to OFF to cancel the differential lock.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VR−03
SA−11 2
−
SUSPENSION AND AXLE COIL SPRING AND REAR SHOCK ABSORBER
969
Author: Date:
1996 LAND CRUISER (RM451U)
COIL SPRING AND REAR SHOCK ABSORBER
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VP−01
R08418
−
SUSPENSION AND AXLE COIL SPRING AND REAR SHOCK ABSORBER
SA−11 3
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE REAR WHEEL
Torque:
Steel wheel: 147 N·m (1,500 kgf·cm, 109 ft·lbf)
Aluminum wheel: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2. REMOVE REAR SHOCK ABSORBER
(a) Remove the lower bolt holding the shock absorber from the rear axle housing.
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
(b) Remove the retainer and 2 cushions, disconnect the shock absorber.
(c) Remove the 2 upper bolts and shock absorber. Torque: 50 N·m (510 kgf·cm, 37 ft·lbf)
(d) Remove these parts from the shock absorber:
Nut
3 Retainers
2 Cushions
Bracket
Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)
3. DISCONNECT STABILIZER BAR BRACKETS FROM
REAR AXLE HOUSING (See page SA−124 )
4. DISCONNECT LATERAL CONTROL ROD FROM REAR AXLE HOUSING (See page SA−11 8 )
5. REMOVE COIL SPRING
(a) Begin to lower the axle housing.
HINT:
Be careful not to snap the brake line and parking brake cable.
(b) With lowering the rear axle housing, remove the coil spring and insulator.
HINT:
Check that the coil spring end is installed correctly.
If the coil spring end is not in the correct position, reinstall the
coil spring.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA−11 4
−
SUSPENSION AND AXLE COIL SPRING AND REAR SHOCK ABSORBER
1996 LAND CRUISER (RM451U)
(c) Remove the bolt and follow spring from the frame.
Torque: 28 N·m (290 kgf·cm, 21 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VQ−01
SA0627
−
SUSPENSION AND AXLE COIL SPRING AND REAR SHOCK ABSORBER
SA−11 5
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT SHOCK ABSORBER
Compress and extend the shock absorber rod and check that
there is no abnormal resistance or unusual operation sounds.
If there is any abnormality, replace the shock absorber with a
new one.
NOTICE:
When discarding the shock absorber, use the following
procedure.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VS−01
SA−11 6
−
SUSPENSION AND AXLE COIL SPRING AND REAR SHOCK ABSORBER
1996 LAND CRUISER (RM451U)
DISPOSAL
DISCARD SHOCK ABSORBER
Before discarding the shock absorber, drill a hole 2 − 3 mm
(0.079 − 0.118 in.) in diameter at the location shown in the il-
lustration to release the gas inside.
NOTICE:
When drilling, chips may fly out, work carefully. The gas is
colorless, odorless and non −poisonous.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1VT−01
−
SUSPENSION AND AXLE COIL SPRING AND REAR SHOCK ABSORBER
SA−11 7
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page SA−11 3 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010