TOYOTA LAND CRUISER 1996 J80 Workshop Manual

P03792
IG−6
−
IGNITION IGNITION SYSTEM
740
Author: Date:
1996 LAND CRUISER (RM451U)
19. ADJUST ELECTRODE GAP
Carefully bend the outer electrode to obtain the correct elec-
trode gap.
Correct electrode gap: 0.8 mm (0.031 in.)
20. INSTALL SPARK PLUGS
Using a 16 mm plug wrench, install the spark plug. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
21. RECONNECT HIGH −TENSION CORDS TO SPARK
PLUGS
NOTICE:
”Cold” and ”Hot” in the following sentences express the
temperature of the coils themselves. ”Cold” is from −10° C
(14 °F) to 50° C (122°F) and ”Hot” is from 50 °C (122° F) to
100 °C (212 °F).
22. DISCONNECT IGNITION COIL CONNECTOR
23. DISCONNECT HIGH−TENSION CORD
24. INSPECT PRIMARY COIL RESISTANCE
Using an ohmmeter, measure the resistance between the posi-
tive (+) and negative (−) terminals. Primary coil resistance:
Cold: 0.36 − 0.55 Ω
Hot: 0.45 − 0.65 Ω
If the resistance is not as specified, replace the ignition coil.
25. INSPECT SECONDARY COIL RESISTANCE
Using an ohmmeter, measure the resistance between the posi-
tive (+) and high −tension terminals.
Secondary coil resistance:
Cold: 9.0 − 15.4 kΩ
Hot: 11.4 − 18.1 kΩ
If the resistance is not as specified, replace the ignition coil.
26. RECONNECT HIGH−TENSION CORD
27. RECONNECT IGNITION COIL CONNECTOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
IGNITION IGNITION SYSTEM
IG−7
741
Author: Date:
1996 LAND CRUISER (RM451U)
NOTICE:
”Cold” and ”Hot” in the following sentences express the
temperature of the coils themselves. ”Cold” is from −10° C
(14 °F) to 50° C (122°F) and ”Hot” is from 50 °C (122° F) to
100 °C (212 °F).
28. DISCONNECT DISTRIBUTOR CONNECTOR
29. REMOVE DISTRIBUTOR CAP WITHOUT DISCON- NECTING HIGH−TENSION CORDS
30. REMOVE ROTOR
31. INSPECT AIR GAPS
Using a thickness gauge, measure the gap between the signal
rotor and the pickup coil projection. Air gap: 0.2 − 0.4 mm (0.008 − 0.016 in.)
If the gap is not as specified, replace the distributor housing.
32. INSPECT SIGNAL GENERATOR (PICKUP COIL) RE- SISTANCE
Using an ohmmeter, check that the resistance of the pickup coil. Pickup coil resistance:
Cold G1 and G
G2 and G
NE and G185 − 275 Ω
185 − 275 Ω
185 − 275 Ω
Hot G1 and G
G2 and G
NE and G240 − 325 Ω
240 − 325 Ω
240 − 325 Ω
If the resistance is not as specified, replace the distributor hous-
ing.
33. REINSTALL ROTOR
34. REINSTALL DISTRIBUTOR CAP
35. RECONNECT DISTRIBUTOR CONNECTOR
NOTICE:
”Cold” and ”Hot” in the following sentences express the
temperature of the sensor itself.
”Cold” is from −10° C (14°F) to 50° C (122°F) and ”Hot” is
from 50° C (122°F) to 100° C (212°F).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22961
IG−8
−
IGNITION IGNITION SYSTEM
742
Author: Date:
1996 LAND CRUISER (RM451U)
36. DISCONNECT CRANKSHAFT POSITION SENSOR
CONNECTOR AND BRACKET
37. INSPECT CRANKSHAFT POSITION SENSOR RESIS- TANCE
Using an ohmmeter, measure the resistance between the ter-
minals. Resistance (NE  − NE ):
Cold: 1,630 − 2,740 Ω
Hot: 2,065 − 3,225 Ω
If the resistance is not as specified, replace the crankshaft posi-
tion sensor.
38. RECONNECT CRANKSHAFT POSITION SENSOR
BRACKET AND CONNECTOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0IC−01
−
IGNITION DISTRIBUTOR
IG−9
743
Author: Date:
1996 LAND CRUISER (RM451U)
DISTRIBUTOR
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0ID−01
IG−10
−
IGNITION DISTRIBUTOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCONNECT DISTRIBUTOR CONNECTOR
2. REMOVE DISTRIBUTOR CAP WITHOUT DISCON- NECTING HIGH−TENSION CORDS
3. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley until the timing mark is aligned with ”0” mark on the timing chain cover.
(b) Check that the distributor rotor direction is as shown.
If not, turn the crankshaft pulley one complete revolution.
4. REMOVE DISTRIBUTOR
(a) Remove the hold −down bolt and pull out the distributor.
(b) Remove the O−ring from the distributor housing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0IE−01
−
IGNITION DISTRIBUTOR
IG−11
1996 LAND CRUISER (RM451U)
INSTALLATION
1. CHECK NO.1 CYLINDER TO TDC/COMPRESSION
If necessary, remove the cylinder head cover, and check these
conditions:
Turn the crankshaft pulley and align its groove with
the timing mark ”0” of the timing chain cover.
Verify that the timing marks with 1 and 2 dots are in
straight line on the cylinder head surface as shown
in the illustration.
If not, turn the crankshaft 1 revolution (360°) and align the mark
as above.
2. INSTALL DISTRIBUTOR
(a) Install a new O−ring to the distributor.
HINT:
Always use a new O −ring when installing the distributor.
(b) Align the groove of the distributor housing with the protru-
sion on the driven gear.
(c) Apply a light coat of engine oil on the O −ring.
(d) Insert the distributor, aligning the center of the flange with
that of the bolt hole on the cylinder head.
(e) Lightly tighten the hold −down bolt.
3. INSTALL DISTRIBUTOR CAP
4. CONNECT DISTRIBUTOR CONNECTOR
5. CHECK IGNITION TIMING (See page EM−10)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0JW−01
IG−12
−
IGNITION CRANKSHAFT POSITION SENSOR
746
Author: Date:
1996 LAND CRUISER (RM451U)
CRANKSHAFT POSITION SENSOR
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0JX−01
−
IGNITION CRANKSHAFT POSITION SENSOR
IG−13
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE ENGINE UNDER COVER
2. REMOVE CRANKSHAFT POSITION SENSOR PRO-
TECTOR
Remove the 3 bolts and crankshaft position sensor protector. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
3. DISCONNECT CRANKSHAFT POSITION SENSOR BRACKET AND CONNECTOR
4. REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt, 2 nuts and crankshaft position sensor. Torque:
Bolt A: 20 N·m (200 kgf·cm, 14 ft·lbf)
Nut B: 9 N·m (90 kgf·cm, 78 in.·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0JY−01
IG−14
−
IGNITION CRANKSHAFT POSITION SENSOR
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page IG−13 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0817
LU08N−03
EM1759
P22601
Oil Pressure Gauge
P08343
Adhesive
−
LUBRICATION OIL AND FILTER
LU−1
712
Author: Date:
1996 LAND CRUISER (RM451U)
OIL AND FILTER
INSPECTION
1. CHECK ENGINE OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If the quality is visibly poor, replace the oil.
Oil grade:
API grade SH Energy−Conserving II multigrade en-
gine oil or ILSAC multigrade engine oil.
Recommended viscosity is as shown in the illustra-
tion, with SAE 5W −30 being the preferred engine oil.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the di\
p-
stick.
If low, check for leakage and add oil up to ”F” mark.
3. REMOVE OIL PRESSURE SWITCH, AND INSTALL OIL
PRESSURE GAUGE
4. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
5. CHECK OIL PRESSURE Oil pressure:
At idle
29 kPa (0.3 kgf/cm
2, 4.3 psi) or more
At 3,000 rpm
245 − 490 kPa (2.5 − 5.0 kgf/cm
2, 36 − 71 psi)
6. REMOVE OIL PRESSURE GAUGE AND REINSTALL OIL PRESSURE SWITCH
(a) Remove the oil pressure gauge.
(b) Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Part No. 08833 −00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(c) Reinstall the oil pressure switch.
7. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010