Brake TOYOTA LAND CRUISER 1996 J80 Workshop Manual

Illustration:
what to do and where 21. CHECK
PISTON STROKE OF OVERDRIVE BRAKE
(a)
Task heading : what to do
SST 09350− 30020 (09350 −06120)
Set part No. Component part No.
Detailed text : how to do task
(b)
Piston stroke: 1.40  1.70 mm (0.0551  0.0669 in.)
Specification
Place SST and a dial indicator onto the overdrive brake pis-
ton as shown in the illustration.
Measure the stroke applying and releasing the compressed
air (392  785 kPa, 4  8 kgf/cm2 or 57 
114 psi) as shown
in the illustration.
IN−2
−
INTRODUCTION HOW TO USE THIS MANUAL
2
Author: Date:
1996 LAND CRUISER (RM451U)
The procedures are presented in a step −by−step format:
The illustration shows what to do and where to do it.
The task heading tells what to do.
The detailed text tells how to perform the task and gives other information\
such as specifications
and warnings.
Example:
This format provides the experienced technician with a FAST TRACK to the information needed. The upper
case task heading can be read at a glance when necessary, and the text below it provides detailed informa-
tion. Important specifications and warnings always stand out in bold type.
6. REFERENCES
References have been kept to a minimum. However, when they are required you are given the page to refer
to.
7. SPECIFICATIONS
Specifications are presented in bold type throughout the text where needed. You never have to leave the
procedure to look up your specifications. They are also found in Service Specificatio\
ns section for quick ref-
erence.
8. CAUTIONS, NOTICES, HINTS:
CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other\
people.
NOTICES are also presented in bold type, and indicate the possibility of damage to the components
being repaired.
HINTS are separated from the text but do not appear in bold. They provide additional information to
help you perform the repair efficiently.
9. SI UNIT
The UNITS given in this manual are primarily expressed according to the SI UNIT (Intern\
ational System of
Unit), and alternately expressed in the metric system and in the English Syste\
m.
Example:
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Illustration:
what to do and where 21. CHECK
PISTON STROKE OF OVERDRIVE BRAKE
(a)
Task heading : what to do
SST 09350− 30020 (09350 −06120)
Set part No. Component part No.
Detailed text : how to do task
(b)
Piston stroke: 1.40  1.70 mm (0.0551  0.0669 in.)
Specification
Place SST and a dial indicator onto the overdrive brake pis-
ton as shown in the illustration.
Measure the stroke applying and releasing the compressed
air (392  785 kPa, 4  8 kgf/cm2 or 57 
114 psi) as shown
in the illustration.
IN−2
−
INTRODUCTION HOW TO USE THIS MANUAL
2
Author: Date:
1996 LAND CRUISER (RM451U)
The procedures are presented in a step −by−step format:
The illustration shows what to do and where to do it.
The task heading tells what to do.
The detailed text tells how to perform the task and gives other information\
such as specifications
and warnings.
Example:
This format provides the experienced technician with a FAST TRACK to the information needed. The upper
case task heading can be read at a glance when necessary, and the text below it provides detailed informa-
tion. Important specifications and warnings always stand out in bold type.
6. REFERENCES
References have been kept to a minimum. However, when they are required you are given the page to refer
to.
7. SPECIFICATIONS
Specifications are presented in bold type throughout the text where needed. You never have to leave the
procedure to look up your specifications. They are also found in Service Specificatio\
ns section for quick ref-
erence.
8. CAUTIONS, NOTICES, HINTS:
CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other\
people.
NOTICES are also presented in bold type, and indicate the possibility of damage to the components
being repaired.
HINTS are separated from the text but do not appear in bold. They provide additional information to
help you perform the repair efficiently.
9. SI UNIT
The UNITS given in this manual are primarily expressed according to the SI UNIT (Intern\
ational System of
Unit), and alternately expressed in the metric system and in the English Syste\
m.
Example:
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN0253
WRONGCORRECT
IN0252
WRONGCORRECT
IN−6
−
INTRODUCTION REPAIR INSTRUCTIONS
6
Author: Date:
1996 LAND CRUISER (RM451U)
(k) Care must be taken when jacking up and supporting the
vehicle. Be sure to lift and support the vehicle at the prop-
er locations (See page IN−8).
Cancel the parking brake on the level place and
shift the transmission in Neutral (or N position).
When jacking up the front wheels of the vehicle at
first place stoppers behind the rear wheels.
When jacking up the rear wheels of the vehicle at
first place stoppers before the front wheels.
When either the front or rear wheels only should be
jacked up, set rigid racks and place stoppers in front
and behind the other wheels on the ground.
After the vehicle is jacked up, be sure to support it
on rigid racks . It is extremely dangerous to do any
work on a vehicle raised on a jack alone, even for
a small job that can be finished quickly.
(l) Observe the following precautions to avoid damage to the
following parts:
(1) Do not open the cover or case of the ECU unless absolutely necessary. (If the IC terminals are
touched, the IC may be destroyed by static electric-
ity.)
(2) To disconnect vacuum hoses, pull off the end, not the middle of the hose.
(3) To pull apart electrical connectors, pull on the con- nector itself, not the wires.
(4) Be careful not to drop electrical components, such
as sensors or relays. If they are dropped on a hard
floor, they should be replaced and not reused.
(5) When steam cleaning an engine, protect the elec- tronic components, air filter and emission −related
components from water.
(6) Never use an impact wrench to remove or install temperature switches or temperature sensors.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

V08127
IN−14
−
INTRODUCTION FOR ALL OF VEHICLES
14
Author: Date:
1996 LAND CRUISER (RM451U)
2. WHEN TOWING FULL −TIME 4WD VEHICLES
Use one of the methods shown below to tow the vehicle.
If the vehicle has trouble in the chassis and drive train, use method 1 \
(flat bed truck).
TransmissionTransfer(w/oASS)
~
Parking
ShiftLever
ShiftLever Center
Center
Towing Method Brake
Position PositionDifferential
Differential
Lock Switch
CDFlatSed Truck
~
IN0309
@WheelLiftType Truck with
Dollies FREE
Applied
lipIIRangeIIHIIPosition OFF(Normal)
~
Driving
ii-;~
@TowingwithRope
L~
ReleasedlINIIRangeIIN/IPosition
OFFt
IN0312
HINT:Donotuse anytowing methods otherthanthose shown above.
Forexample, thetowing method shownbelowisdangerous, sodo not use it.
NO
~
IN0313
During towing withthistowing method, thereisadanger of thedrivetrain
heating upand causing breakdown, orofthe front wheels flyingoffthe
dolly.
\127
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN04S−30
−
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN−17
17
Author: Date:
1996 LAND CRUISER (RM451U)
HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS
GENERAL INFORMATION
A large number of ECU controlled systems are used in the LAND CRUISER. In general, the ECU controlled
system is considered to be a very intricate system requiring a high level of t\
echnical knowledge and expert
skill to troubleshoot. However, the fact is that if you proceed to inspect the circuits one by one, trou\
bleshoot-
ing of these systems is not complex. If you have adequate understanding of the system and a basic knowl-
edge of electricity, accurate diagnosis and necessary repair can be performed to locate and fix the pr\
oblem.
This manual is designed through emphasis of the above standpoint to help service techn\
icians perform ac-
curate and effective troubleshooting, and is compiled for the following major ECU con\
trolled systems:
The troubleshooting procedure and how to make use of it are described on\
the following pages.
SystemPage
1. EngineDI−1
2. Automatic TransmissionDI−129
3. Anti− Lock Brake SystemDI−188
4. Supplemental Restraint SystemDI−238
5. Cruise Control SystemDI−284
FOR USING OBD II SCAN TOOL OR TOYOTA HAND−HELD TESTER
Before using the scan tool or tester, the scan tool’ s instruction book or tester’s operator manual should
be read thoroughly.
If the scan tool or tester cannot communicate with ECU controlled systems \
when you have connected
the cable of the scan tool or tester to DLC3, turned the ignition switch\
ON and operated the scan tool,
there is a problem on the vehicle side or tool side.
(1) If communication is normal when the tool is connected to another vehicle, \
inspect the diagnosis data link line (Bus line) or ECU power circuit of the vehicle.
(2) If communication is still not possible when the tool is connected to anoth\
er vehicle, the problem is probably in the tool itself, so perform the Self Test procedures outline in the Tester Operator’s
Manual.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DIAGNOSTIC TROUBLE CODE CHECK PROCEDURE
Diagnostic Trouble
Code Check (Make a
note of and then clear) Confirmation
of Symptoms
Diagnostic Trouble
Code Check
Problem Condition
Diagnostic Trouble
Code Display Problem symptoms
exist
Same diagnostic
trouble code is
displayed Problem is
still occurring in the diagnostic
circuit
Normal code is
displayed The problem is still occurring in a place
other than in the diagnostic circuit
(The diagnostic trouble code displayed
first is either for a past problem or it is a
secondary problem)
No problem
symptoms exist
The problem occurred in the diagnostic
circuit in the past
Normal Code Display Problem symptoms
existNormal code is
displayed The problem is still occurring in a place
other than in the diagnostic circuit
No problem
symptoms exist
Normal code is
displayed The problem occurred in a place other
than in the diagnostic circuit in the past
IN−20−
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
1996 LAND CRUISER (RM451U)
2. SYMPTOM CONFIRMATION AND DIAGNOSTIC TROUBLE CODE CHECK
The diagnostic system in the LAND CRUISER fulfills various functions. The first functio\
n is the Diagnostic
Trouble Code Check in which a malfunction in the signal circuits to the ECU is stored in co\
de in the ECU
memory at the time of occurrence, to be output by the technician during troubl\
eshooting. Another function
is the Input Signal Check which checks if the signals from various switc\
hes are sent to the ECU correctly.
By using these check functions, the problem areas can be narrowed down qui\
ckly and troubleshooting can
be performed ef fectively. Diagnostic functions are incorporated in the following systems in the LAND CRUIS-
ER.
SystemDiagnostic Trouble
Code CheckInput Signal Check(Sensor Check)Diagnostic Test
Mode (Active Test)
1. Engine
(with Check Mode)
2. Automatic T ransmission
(with Check Mode)
3. Anti− Lock Brake System
4. Supplemental Restraint System
5. Cruise Control System
In diagnostic trouble code check, it is very important to determine whethe\
r the problem indicated by the diag-
nostic trouble code is still occurring or occurred in the past but returned to\
normal at present. In addition,
it must be checked in the problem symptom check whether the malfunction \
indicated by the diagnostic
trouble code is directly related to the problem symptom or not. For this reason, the \
diagnostic trouble codes
should be checked before and after the symptom confirmation to determine the curre\
nt conditions, as shown
in the table below. If this is not done, it may, depending on the case, result in unnecessary troubleshooting
for normally operating systems, thus making it more difficult to locate the problem, or in repairs not pertinent
to the problem. Therefore, always follow the procedure in correct order an\
d perform the diagnostic trouble
code check.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN04Q−07
−
INTRODUCTION TERMS
IN−33
33
Author: Date:
1996 LAND CRUISER (RM451U)
TERMS
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti−Lock Brake System
ACAlternating Current
ACCAccessory
ACISAcoustic Control Induction System
ACSDAutomatic Cold Start Device
A.D.D.Automatic Disconnecting Differential
A/FAir−Fuel Ratio
AHCActive Height Control Suspension
ALRAutomatic Locking Retractor
ALTAlternator
AMPAmplifier
ANTAntenna
APPROX.Approximately
A/TAutomatic Transmission (Transaxle)
AT FAutomatic Transmission Fluid
AUTOAutomatic
AUXAuxiliary
AV GAverage
AV SAdaptive Variable Suspension
BABrake Assist
BACSBoost Altitude Compensation System
BATBattery
BDCBottom Dead Center
B/LBi−Level
B/SBore−Stroke Ratio
BTDCBefore Top Dead Center
BVSVBimetallic Vacuum Switching V alve
Calif.California
CBCircuit Breaker
CCoCatalytic Converter For Oxidation
CDCompact Disc
CFCornering Force
CGCenter Of Gravity
CHChannel
COMB.Combination
CPECoupe
CPSCombustion Pressure Sensor
CPUCentral Processing Unit
CRSChild Restraint System
CTRCenter
C/VCheck Valve
CVControl Valve
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN−34
−
INTRODUCTION TERMS
34
Author: Date:
1996 LAND CRUISER (RM451U)
CW
Curb W
eight
DCDirect Current
DEFDefogger
DFLDeflector
DIFF.Differential
DIFF. LOCKDifferential Lock
D/INJDirect Injection
DLIDistributorless Ignition
DOHCDouble Over Head Cam
DPDash Pot
DSDead Soak
DSPDigital Signal Processor
EBDElectronic Brake Force Distribution
ECAMEngine Control And Measurement System
ECDElectronic Controlled Diesel
ECDYEddy Current Dynamometer
ECUElectronic Control Unit
EDElectro−Deposited Coating
EDICElectric Diesel Injection Control
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGR−VMExhaust Gas Recirculation −Vacuum Modulator
ELREmergency Locking Retractor
ENGEngine
ESAElectronic Spark Advance
ETCSElectronic Throttle Control System
EVPEvaporator
E−VRVElectric V acuum Regulating V alve
EXHExhaust
FEFuel Economy
FFFront−Engine Front− Wheel−Drive
F/GFuel Gage
FIPGFormed In Place Gasket
FLFusible Link
F/PFuel Pump
FPUFuel Pressure Up
FrFront
FRFront−Engine Rear− Wheel−Drive
F/WFlywheel
FW/DFlywheel Damper
FWDFront−Wheel−Drive
GASGasoline
GSAGear Shift Actuator
GNDGround
HACHigh Altitude Compensator
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN−36
−
INTRODUCTION TERMS
36
Author: Date:
1996 LAND CRUISER (RM451U)
NA
Natural Aspiration
No.Number
O/DOverdrive
OEMOriginal Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead V
alve
OPTOption
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
PKBParking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take−Off
R & PRack And Pinion
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight−Hand
RHDRight−Hand Drive
RLYRelay
ROMRead Only Memory
RrRear
RRRear−Engine Rear −Wheel Drive
RRSRigid Rear Suspension
RWDRear− Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SMTSequential Manual T ransmission
SOCState Of Charge
SOHCSingle Overhead Camshaft
SPECSpecification
SPISingle Point Injection
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
STJCold−Start Fuel Injection
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TBIThrottle Body Electronic Fuel Injection
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0SZ−01
V07130
Shift Lever PositionGear PositionParkingC0C1C2B0B1B2B3F0F1F2
Reverse
Neutral 1st
2nd
3rd
O/D
P
R
N
D
2
L
1st
2nd
*1
3rd
1st
*2 2nd
Operating
*1 Down− shift only in the 2 position and 3rd gear −no up− shift.
*2 Down− shift only in the L position and 2nd gear −no up− shift.
O/D Direct
Clutch (C
0)
2nd Coast Brake (B1)
O/D Brake (B
0) Direct
Clutch (C2)
Forward Clutch (C
1)
2nd Brake (B
2)
1st & Reverse
Brake (B
3)
Rear Planetary Carrier
Rear Planetary Ring Gear
Output Shaft
Front & Rear Planetary
Sun Gear
No.2 One−Way
Clutch (F
2)
No.1 One−Way
Clutch (F
1)
Front Planetary
Ring Gear
Front Planetary
Carrier
O/D Planetary
Ring Gear
O/D Planetary
Carrier
O/D Planetary
Sun Gear
Input Shaft
O/D Input Shaft
O/D One−Way
Clutch (F
0)
AT−2
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION SYSTEM
1996 LAND CRUISER (RM451U)
OPERATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010