TOYOTA RAV4 1996 Service Repair Manual

Fig. 20: Power Window System Wiring Diagram (4Runner)

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:36 AMPage 39 © 2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:36 AMPage 40 © 2005 Mitchell Repair Information Company, LLC.

Fig. 21: Tailgate Power Window System Wiring Diagram (4Runner)

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:36 AMPage 41 © 2005 Mitchell Repair Information Company, LLC.

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:36 AMPage 42 © 2005 Mitchell Repair Information Company, LLC.

Fig. 22: Rear Quarter Power Window System Wiring Diagram (Land Cruiser)

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:36 AMPage 43 © 2005 Mitchell Repair Information Company, LLC.

1999-2000 ACCESSORIES & EQUIPMENT
Wiper/Washer Systems
DESCRIPTION & OPERATION
All models are equipped with 2-speed wiper motors. An intermittent wiper system is optional. Front wiper
motors are protected by an internal circuit breaker. Celica, Land Cruiser, RAV4, Sienna and 4Runner are
equipped with rear wipers.
ADJUSTMENTS
Adjust wiper blades as specified. See WIPER BLADE ADJUSTMENTS table.
WIPER BLADE ADJUSTMENTS NOTE: This article also applies to Lexus LX470. Refer to Land Cruiser, unless
otherwise indicated.
WARNING:Deactivate air bag system before performing any service operation. See
AIR BAG RESTRAINT SYSTEMS. DO NOT apply electrical power to any
component on steering column without first deactivating air bag system.
Air bag may deploy.
Adjustment (1) In. (mm)
Avalon
"A"1.6 (40)
"B"2.6 (65)
Camry & Camry Solara
"A" & "B"1.4 (35)
Celica
Front
"A"1.42 (36)
"B".81 (20.5)
Rear(2)
Corolla
"A".98 (25)
"B".59 (15)
Land Cruiser & Lexus LX470
Front
"A"1.57 (40)
"B"1.02 (26)
Rear (3) .39-1.5 (28-48)

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Wiper/Washer Systems

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Wiper/Washer Systems
Microsoft
Sunday, November 22, 2009 11:01:19 AMPage 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, November 22, 2009 11:01:24 AMPage 1 © 2005 Mitchell Repair Information Company, LLC.

RAV4
Front
"A" & "B".98 (25)
Rear (3) 7.2 (184)
Sienna
Front
"A".98 (25)
"B"1.26 (32)
Rear1.52 (54)
Tacoma
"A" & "B".98 (25)
Tundra(4)
4Runner
Front
"A" & "B".98 (25)
Rear(4)
(1)See Fig. 1 .
(2)Adjust top of wiper blade to installation mark printed on glass.
(3)From lower edge of rear window to end of blade.
(4)Information is not available from manufacturer.

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Wiper/Washer Systems
Microsoft
Sunday, November 22, 2009 11:01:19 AMPage 2 © 2005 Mitchell Repair Information Company, LLC.

Fig. 1: Adjusting Front Wiper Blades
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
COMPONENT TESTS
FRONT WIPER MOTOR TEST
Avalon
1. Using a 12-volt battery, connect jumper wire from positive battery terminal to wiper motor terminal No.
3. See Fig. 2
. Connect another jumper wire between negative battery terminal and wiper motor terminal
No. 1. Motor should operate at low speed.
2. Remove jumper wire from terminal No. 3. Reconnect positive battery terminal jumper wire to wiper
motor terminal No. 2. Motor should operate at high speed.
3. Remove jumper wire from terminal No. 2 and reconnect jumper wire to wiper motor terminal No. 3. With
motor running at low speed, stop motor at any position except PARK position by disconnecting jumper
wire from terminal No. 3. Install another jumper wire between wiper motor terminals No. 1 and 3.
4. Connect positive battery terminal jumper wire to wiper motor terminal No. 2. Connect negative jumper to
terminal No. 5. Motor should start running and then stop at PARK position. Replace motor if operation is
not as specified. See FRONT WIPER MOTOR
under REMOVAL & INSTALLATION.
Celica, Corolla & RAV4
1. Using a 12-volt battery, connect jumper wire from positive battery terminal to wiper motor terminal No.

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Wiper/Washer Systems
Microsoft
Sunday, November 22, 2009 11:01:19 AMPage 3 © 2005 Mitchell Repair Information Company, LLC.

3. See Fig. 2 . Connect another jumper wire between negative battery terminal and wiper motor terminal
No. 1. Motor should operate at low speed.
2. Remove jumper wire from terminal No. 3. Reconnect positive battery terminal jumper wire to wiper
motor terminal No. 2. Motor should operate at high speed.
3. Remove jumper wire from terminal No. 2 and reconnect jumper wire to wiper motor terminal No. 3. With
motor running at low speed, stop motor at any position except PARK position by disconnecting jumper
wire from terminal No. 3. Install another jumper wire between wiper motor terminals No. 3 and 5.
4. Connect positive battery terminal jumper wire to wiper motor terminal No. 6. Connect negative jumper to
terminal No. 1. Motor should start running and then stop at PARK position. Replace motor if operation is
not as specified. See FRONT WIPER MOTOR
under REMOVAL & INSTALLATION.
Camry, Camry Solara, Tacoma & Tundra
1. Using a 12-volt battery, connect jumper wire from positive battery terminal to wiper motor terminal No.
5. See Fig. 3
. Connect another jumper wire from negative battery terminal to wiper motor terminal No. 4.
Motor should operate at low speed.
2. Remove jumper wire from terminal No. 5. Reconnect jumper wire to wiper motor terminal No. 3. Motor
should operate at high speed. Remove jumper wire from terminal No. 3 and reconnect jumper wire to
wiper motor terminal No. 5. With motor running at low speed, stop motor at any position except PARK
position by disconnecting jumper wire from terminal No. 5. On Camry and Camry Solara, install jumper
wire between wiper motor terminals No. 3 and 5. On Tacoma and Tundra, install jumper wire between
wiper motor terminals No. 1 and 5.
3. On all models, connect positive battery terminal jumper wire to wiper motor terminal No. 2. Connect
negative battery terminal jumper wire to wiper motor terminal No. 4. Motor should start running and then
stop at PARK position. Replace motor if operation is not as specified. See FRONT WIPER MOTOR

under REMOVAL & INSTALLATION.
Land Cruiser & Lexus LX470
1. Using a 12-volt battery, connect jumper wire from positive battery terminal to wiper motor terminal No.
1. See Fig. 3
. Connect another jumper wire between negative battery terminal and wiper motor terminal
No. 5. Wiper motor should operate at low speed.
2. Remove jumper wire from terminal No. 1. Reconnect jumper wire to wiper motor terminal No. 4. Motor
should operate at high speed. Remove jumper wire from terminal No. 4 and reconnect jumper wire to
wiper motor terminal No. 1. With motor running at low speed, stop motor at any position except PARK
position by disconnecting jumper wire from terminal No. 1. Install another jumper wire between wiper
motor terminals No. 1 and 3.
3. Ensure ground is still connected to terminal No. 5. Connect positive battery terminal jumper wire to wiper
motor terminal No. 2. Motor should start running and then stop at PARK position. Replace motor if
operation is not as specified. See FRONT WIPER MOTOR
under REMOVAL & INSTALLATION.
Sienna
1. Using a 12-volt battery, connect jumper wire from positive battery terminal to wiper motor terminal No.
5. See Fig. 4
. Connect another jumper wire between negative battery terminal and wiper motor terminal
No. 1. Wiper motor should operate at low speed.

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Wiper/Washer Systems
Microsoft
Sunday, November 22, 2009 11:01:20 AMPage 4 © 2005 Mitchell Repair Information Company, LLC.

2. Remove jumper wire from terminal No. 5. Reconnect jumper wire to wiper motor terminal No. 4. Motor
should operate at high speed. Remove jumper wire from terminal No. 4 and reconnect jumper wire to
wiper motor terminal No. 5. With motor running at low speed, stop motor at any position except PARK
position by disconnecting jumper wire from terminal No. 5. Install another jumper wire between wiper
motor terminals No. 2 and 5.
3. Ensure ground is still connected to terminal No. 1. Connect positive battery terminal jumper wire to wiper
motor terminal No. 3. Motor should start running and then stop at PARK position. Replace motor if
operation is not as specified. See FRONT WIPER MOTOR
under REMOVAL & INSTALLATION.
4Runner
1. Using a 12-volt battery, connect jumper wire from positive battery terminal to wiper motor terminal No.
3. See Fig. 2
or Fig. 5 . Connect another jumper wire between negative battery terminal and wiper motor
body. Motor should operate at low speed.
2. Remove jumper wire from terminal No. 3. Reconnect positive battery terminal jumper wire to wiper
motor terminal No. 2. Motor should operate at high speed.
3. Remove jumper wire from terminal No. 2 and reconnect jumper wire to wiper motor terminal No. 3. With
motor running at low speed, stop motor at any position except PARK position by disconnecting jumper
wire from terminal No. 3. Install another jumper wire between wiper motor terminals No. 2 and 3.
4. Ensure wiper motor body is still connected to battery negative terminal. Connect positive battery terminal
jumper wire to wiper motor terminal No. 4. Motor should start running and then stop at PARK position.
Replace motor if operation is not as specified. See FRONT WIPER MOTOR
under REMOVAL &
INSTALLATION.

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Wiper/Washer Systems
Microsoft
Sunday, November 22, 2009 11:01:20 AMPage 5 © 2005 Mitchell Repair Information Company, LLC.