TOYOTA SEQUOIA 2001 Service Repair Manual

SA2BH±02
F14305
F14306
F16918
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
SA±137
3133 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE REAR WHEELS
Torque: 110 N´m (1,150 kgf´cm, 83 ft´lbf)
2. SUPPORT REAR AXLE HOUSING WITH JACK
3. Normal Type:
REMOVE SHOCK ABSORBER
(a) Remove the bolt and disconnect the shock absorber from
the axle housing.
Torque: 87 N´m (887 kgf´cm, 64 ft´lbf)
(b) Use the same procedure described above to the other
side.
(c) While holding the piston rod, remove the nut, 2 retainers,
cushion and shock absorber.
Torque: 58 N´m (591 kgf´cm, 43 ft´lbf)
(d) Remove the 2 retainers and cushion from the shock ab-
sorber.
4. Auto Leveler Type:
REMOVE SHOCK ABSORBER
NOTICE:
When removing and installing of the shock absorber, per-
form the procedure with the shock absorber stretched
completely. The primary rod reaction force of the shock ab-
sorber is apploximately 1,000 N.
(a) Remove the bolt and disconnect the shock absorber from
the axle housing.
Torque: 87 N´m (887 kgf´cm, 64 ft´lbf)
(b) Use the same procedure described above to the other
side.

F16919
F16920
F14307
F04396
SA±138
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
3134 Author: Date:
2005 SEQUOIA (RM1146U)
(c) While holding the piston rod, remove the nut, retainer,
cushion and shock absorber.
Torque: 58 N´m (591 kgf´cm, 43 ft´lbf)
(d) Remove the retainer and cushion from the shock absorb-
er.
5. DISCONNECT LH AND RH STABILIZER BAR LINKS
Remove the 2 nuts and disconnect the LH and RH stabilizer bar
links.
Torque: 69 N´m (704 kgf´cm, 51 ft´lbf)
6. DISCONNECT LATERAL CONTROL ROD
Remove the nut, washer, bolt and disconnect the lateral control
rod.
Torque: 140 N´m (1,428 kgf´cm, 103 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nut and bolt.
7. REMOVE COIL SPRING
(a) Lower the axle housing.
NOTICE:
Be careful not to snap the brake line and parking brake
cable.
(b) While lowering the axle housing, remove the coil spring,
hollow spring and insulator.
HINT:
At the time of installation, please refer to the following items.

Check that the coil spring end is installed correctly.

If the coil spring end is not in the correct position, reinstall
the coil spring.

SA174±05
SA0627
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
SA±139
3135 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
Normal Type:
INSPECT SHOCK ABSORBER
Compress and extend the shock absorber rod and check that
there is no abnormal resistance or unusual operation sounds.
If there is any abnormality, replace the shock absorber with a
new one.

SA2BI±02
W03120F07370
50 mm
(1.97 in.)30 mm
(1.18 in.)
F17130
50 mm (1.97 in.) High Pressure
Chamber Side:130 mm (5.12 in.)
F17131
Low Pressure
Chamber Side:50 mm (1.97 in.)
40 mm (1.57 in.) SA±140
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
3136 Author: Date:
2005 SEQUOIA (RM1146U)
DISPOSAL
1. FULLY EXTEND SHOCK ABSORBER ROD
2. Normal Type:
DRILL HOLE TO REMOVE GAS FROM CYLINDER
Using a drill, make a hole in the cylinder, as shown in the illustra-
tion to discharge the gas inside.
CAUTION:
The discharged gas is harmless, but be careful of chips
which may fly out when drilling.
3. Auto Leveler Type:
DRILL HOLE TO REMOVE GAS FROM CYLINDER
Using a drill, make a hole on the shaded area of the cylinder,
as shown in the illustration to discharge the gas inside.
CAUTION:

Be sure to perform the procedure in the order, the
high pressure chamber and the low pressure cham-
ber.

Wear protective goggles and cover the absorber with
a plastic bag or like when boring.

The discharged gas is harmless, but be careful of
chips which may fly out when drilling.

SA175±05
F05063
SST
SST
F14312
SST
SST
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
SA±141
3137 Author: Date:
2005 SEQUOIA (RM1146U)
REPLACEMENT
1. Normal Type:
REMOVE BUSHING
Using SST and a press, remove the bushing.
SST 09710±14013 (09710±00061),
09710±28012 (09710±07031),
09950±70010 (09951±07100)
2. Normal Type:
INSTALL BUSHING
Using SST and a press, install a new bushing.
SST 09710±14013 (09710±00061),
09710±28012 (09710±07031),
09950±70010 (09951±07100)

SA176±04
SA±142
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
3138 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page SA±137).

SA177±04
F14296
Lateral Control Rod
N´m (kgf´cm, ft´lbf) : Specified torque
130 (1,326, 96)

140 (1,428, 103)


Non±reusable part
± SUSPENSION AND AXLEREAR LATERAL CONTROL ROD
SA±143
3139 Author: Date:
2005 SEQUOIA (RM1146U)
REAR LATERAL CONTROL ROD
COMPONENTS

SA178±04
F14297
A
B SA±144
± SUSPENSION AND AXLEREAR LATERAL CONTROL ROD
3140 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. SUPPORT REAR AXLE HOUSING WITH JACK
2. REMOVE LATERAL CONTROL ROD
Remove the 2 bolts, nut, washer and lateral control rod.
Torque:
A 140 N´m (1,428 kgf´cm, 103 ft´lbf)
B 130 N´m (1,326 kgf´cm, 96 ft´lbf)
HINT:
At the time of installation, please refer to the following items.

Replace the used nut with a new one.

After stabilizing the suspension, torque the nut and bolt.

SA179±01
± SUSPENSION AND AXLEREAR LATERAL CONTROL ROD
SA±145
3141 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page SA±144).

SA17B±05
F14298
Speed Sensor
Wire Harness
Lower Control Arm
N´m (kgf´cm, ft´lbf) : Specified torque
Upper Control Arm
140 (1,428, 103)
140 (1,428, 103)
28 (286, 21)
130 (1,326, 96)
26 (265, 19)
Parking Brake Cable130 (1,326, 96)
Brake Line
Bracket
SA±146
± SUSPENSION AND AXLEREAR UPPER AND LOWER CONTROL ARM
3142 Author: Date:
2005 SEQUOIA (RM1146U)
REAR UPPER AND LOWER CONTROL ARM
COMPONENTS