TOYOTA SIENNA 2007 Service Repair Manual

DS–16DRIVE SHAFT – FRONT DRIVE SHAFT
DS
(2) Tighten the SST so that the No. 2 front axle
inboard joint boot LH clamp is pinched.
SST 09521-24010
NOTICE:
Do not overtighten the SST.
(3) Using SST, measure the clearance of the No. 2
front axle inboard joint boot LH clamp.
SST 09240-00020
Clearance:
0.8 mm (0.031 in.) or less
NOTICE:
When the measured value is greater than
the specified value, retighten the clamp.
(d) for claw engagement type:
(1) Using needle nose pliers, install the No. 2 front
axle inboard joint boot clamp as shown in the
illustration.
16. INSTALL FRONT AXLE INBOARD JOINT BOOT LH
CLAMP
(a) Install the front axle inboard joint boot LH clamp
perform the same procedures as for the No. 2 front
axle inboard joint boot LH clamp.
17. INSPECT FRONT DRIVE SHAFT ASSEMBLY
(a) Check that there is no excessive play in the
outboard joint.
(b) Check that the inboard joint slides smoothly in the
thrust direction.
(c) Check that there is no excessive play in the radial
directions of the inboard joint.
C108292E03
C086270E05
C160031E01
C091598

DRIVE SHAFT – FRONT DRIVE SHAFTDS–17
DS
(d) Check the boots for damage.
HINT:
For dimension (A), refer to the following table.
F045048E04
DRIVE TYPE LH mm (in.) RH mm (in.)
2WD638.40 +- 5.0 (25.1338 +-
0.20)957.00 +- 5.0 (37.6771 +-
0.20)
4WD553.64 +- 5.0 (21.7968 +-
0.20)992.24 +- 5.0 (39.0645 +-
0.20)

PREPARATION – 2GR-FE FUELPP–9
PP
RECOMMENDED TOOLS
09082-00040 TOYOTA Electrical Tester

PP–10PREPARATION – 2GR-FE FUEL
PP
EQUIPMENT
Measuring Flask
Ohmmeter
Stopwatch
To r q u e w r e n c h
Vernier calipers
Plastic bag

PREPARATION – 2GR-FE EMISSION CONTROLPP–11
PP
EQUIPMENT
vacuum pump
Ohmmeter
Service Wire Harness
Torque wrench
Pressure gauge
Vernier calipers

PP–12PREPARATION – 2GR-FE EMISSION CONTROL
PP
SSM
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

PP–14PREPARATION – 2GR-FE COOLING
PP
EQUIPMENT
Ohmmeter -
Radiator cap tester -
Thermometer -
To r q u e w r e n c h -
Slide calipers -
Heater -
Ammeter (A) -

PREPARATION – 2GR-FE COOLINGPP–15
PP
COOLANT
Capacity Classification
11.3 liters (12.0 US qts, 10.0 Imp. qts) Use only "TOYOTA Super Long Life Coolant" or similar high quality
ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate
coolant with long-life hybrid organic acid technology (coolant with
long-life hybrid organic acid technology consists of a combination of
low phosphates and organic acids).

PP–16PREPARATION – 2GR-FE COOLING
PP
SSM
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent -

PP–16PREPARATION – 2GR-FE LUBRICATION
PP
LUBRICANT
Item Condition Capacity Classification
Oil grade - - 5W-30: API grade SL Energy-
Conserving, SM Energy-
Conserving or ILSAC multigrade
engine oil
Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 Imp.
qts)-
without oil filter change 5.7 liters (6.0 US qts, 5.0 Imp.
qts)-
Dry fill Dry fill 7.1 liters (7.5 US qts, 6.2Imp. qts) -