display TOYOTA SIENNA HYBRID 2021 Accessories, Audio & Navigation (in English)

1674-7. Rear seat entertainment system operation
4
Audio/visual system
nected to the vehicle Wi-Fi®
access point once, the access
point information will remain on
the device, enabling it automati-
cally connect the next time the
device is brought within access
point range, unless the access
point name or password is
changed.
To change the access point
name and password, select
“Refresh”. If changed while a
device is connected to the
access point, the connection will
be canceled.
1 Select “Refresh”.
2 Select “Yes”.
●The Wi-Fi® access point name
and password can only be
changed after “Refresh” is
selected. (The settings will be
retained when the power switch is
turned off then on.)
●If the automatic connection of a previously connected device is not
desired, perform any of the follow-
ing:
• Select “Refresh” on the system.
• Turn the system to another mode.
• Disable the Wi-Fi
® connection of
the system.
• Disable the Wi-Fi
® connection of
the device.
Press to play.
Press and hold to fast
rewind.
Press to pause.
During playback: Press and
hold to fast forward.
During a pause: Press and
hold to slow forward.
*
Press to display the option
screen. ( P.168)
*: Video only
Remote controller
A
B
C
D
E

1684-7. Rear seat entertainment system operation
■Control screen (Audio
source selection screen)The Wi-Fi
® function is turned
on/off.
Select to display Wi-Fi
® sys-
tem information
■Control screen (Option
screen)
Video
1 Press the “OPTION” button
on the remote controller.
2 Check that the following
screen is displayed.
Select to turn off the option
screen.
Select and hold to fast
rewind.
Select to play/pause.
During playback: Select and hold to fast forward.
During a pause: Select and
hold to slow forward.
Rear display
A
B
A
B
C
D

1704-7. Rear seat entertainment system operation
Using the “SOURCE” button
on the remote controller
1 Select “Rear-Miracast™” on
the audio source selection
screen. ( P.162)
Using each function button on
the remote controller
1 Press the “Miracast” button.
2 Check that the following
screen is displayed.
3 Activate Miracast
® on the
device and set it to output to
the rear seat entertainment
system.
●Miracast® streaming will stop in
the following situations:
• The Miracast
® function of the con-
nected device is turned off.
• Select “Disconnect” on the rear-
Miracast
® operation screen.
• The rear seat entertainment sys-
tem source is chan ged to a differ-
ent source. ( P.162)
1 Select “Rear-Miracast™” on
the audio source selection
screen. ( P.162) 2
Select “Disconnect”.
Connecting to the system
Disconnecting from the
system

1714-8. Rear seat entertainment system settings
4
Audio/visual system
4-8.Rear seat entertainment system settings
1Press the “SETTING” button.
2 Select the desired tab to be
set.
 After performing adjust-
ments, press the “SETTING”
button on the remote control-
ler.
Select to adjust the screen.
( P.171)
Select to change the screen
size. ( P.171)
Select to display the other
settings screen. ( P.172)
Select to turn the rear display
off.
Press the “SETTING” button on the remote controller to
turn the rear display back on.
The screen image quality, such
as the brightness and contrast
levels, can be adjusted. Adjust-
able items depend on the
selected input source.
1 Display the settings screen.
( P.171)
2 Select the “Display” tab.
3 Select the desired item to be
set.
Select to weaken or
strengthen the contrast.
Select to darken or brighten
the screen.
The screen size can be changed
for each input mode individually.
1 Display the settings screen.
( P.171)
2 Select the “Screen size” tab.
Rear display settings
Displaying the settings
screen
A
B
C
D
$GMXVWLQJWKHVFUHHQ
&KDQJLQJWKHVFUHHQVL]H
A
B

1724-8. Rear seat entertainment system settings
3Select the desired screen
size.
Select to display the screen
at the original ratio.
Select to widen the 4:3
aspect screen horizontally to
fill the screen.
●Depending on the source, some
functions may not be available.
1Display the settings screen.
( P.171)
2 Select the “Other” tab.
3 Select the desired item to be
set.
Select to turn on/off the “LCD
AI”. The “LCD AI” automati-
cally determines the tone of
the video image and sets the
contrast to an optimum level, displaying a sharp image.
*
Select to turn the “Super res-
olution” function on/off.
When turned on, the “Super
resolution” function enhances
image quality to deliver a
feeling of a higher resolution
image.
*
Select to turn the “Overscan”
function on/off.
*
When turned on, this function
hides image distortion at the
edge of the screen.
(Part of the image may be cut
off.)
*: This function is not available
depending on the screen.
Other settings screen
A
B
A
B
C

1835-1. Voice command system operation
5
Voice command system
nize.
• There is excessive background noise, such as wind noise.
●Normally, it is necessary to wait
for a beep befor e saying a com-
mand. To enable the ability to talk
over prompts and say commands
before the beep, enable the voice
prompt interrupt function. ( P.64)
●This system ma y not operate
immediately after the power
switch is in ACC or ON.
The voice command system is
operated by saying commands
which correspond to a sup-
ported function. To display
examples of commands for sup-
ported functions, select a func-
tion button on the screen after
starting the voice command sys-
tem. 1
Press the talk switch.
 Voice guidance for the voice
command system can be
skipped by pressing the talk
switch.
2 If “Getting Started with Voice”
screen is displayed, select
“OK” or press the talk switch.
( P.184)
3 After hearing a beep, say a
supported command.
 To display sample commands
of the desired function, say
the desired function or select
the desired function button.
To display more commands,
select “More Commands”.
 Selecting “Help” or saying
“Help” prompts the voice com-
mand system to offer exam-
ples of commands and
operation methods.
 Registered POIs, registered
names in the contacts list etc.,
can be said in the place of the
“<>” next to the commands.
( P.205)
NOTICE
●Do not touch and put a sharp
object to the microphone. It may
cause failure.
Voice command system
operation
Operation from the main
menu

1845-1. Voice command system operation
For example: Say “Find a restau-
rant”, “Call John Smith” etc.
If a desired outcome is not
shown, or if no selections are
available, perform one of the
following to return to the pre-
vious screen:
• Say “Go back”.
• Select .
To cancel voice recognition,
select , say “Cancel”, or
press and hold the talk switch.
 To perform the voice com-
mand operation again, select
“Start Over” or say “Start
over”.
 To suspend voice command
operation, select “Pause” or
say “Pause”. To resume the
voice command operation,
select “Resume” or press the
talk switch.
●If the system does not respond or
the confirmation screen does not
disappear, press the talk switch
and try again.
●If a voice command cannot be rec-
ognized 3 consecutive times,
voice recognition will be canceled.
●Voice recognition prompts can be
changed on the voice settings
screen. ( P.64)
This function can be used to cancel
voice guidance by turning the voice
prompts off. When you press the
talk switch while using this setting, a
beep sounds, and then you can
immediately say a command.
●Some voice guidance can be can-
celed by setting voice prompts to off. Use this setting when it is
desirable to say a command
immediately after pressing the talk
switch and hearing a beep.
To increase voice recognition
performance, use the “Tutori-
als” and “Voice Training” func-
tions on the “Getting Started
with Voice” screen. These func-
tions are only available when
the vehicle is not moving.
The “Tutorials” and “Voice
Training” functions can also be
started on the voice settings
screen. (
P.64)
1 Press the talk switch.
2 Select the desired item to be
set.
Select to display the voice
command tutorials.
Select to train the voice com-
mand system.
The user will be a sked to say 10
sample phrases. This will help the
voice command system adapt to
the user’s accent.
Select to prevent the screen
from being displayed again.
Increasing the voice rec-
ognition performance
A
B
C

1855-1. Voice command system operation
5
Voice command system
Select to proceed to the
voice command screen.
*: Premium Audio only. This func-tion is not made available in
some countries or areas.
Text messages can be written
using the dictation function.
To use the dictation function, a
subscription to the connected
services is nec essary. Contact
your Toyota dealer for details.
1 Select .
2 Speak to the system.
 Words recognized through
your speech will be displayed.
To confirm the entered text,
select “OK”.
●A keyboard screen will not be dis-
played when the vehicle is being
driven.
●Text message reply with the dicta-
tion function may n ot be available
depending on the type of cellular
phone.
*: Premium Audio only. This func-
tion is not made available in
some countries or areas.Dictation function (English
only)
*
DNatural language
understanding*
Due to natural language
speech recognition technol-
ogy, this system recognizes
commands when spoken
naturally. (If a connected
services subscription has
been entered, the system
will be able to connect to
the Cloud and the range of
naturally spoken English
which can be recognized
will be increased.) However,
the system cannot recog-
nize every variation of each
command. In some situa-
tions, it is possible to omit
the command for the proce-
dure and directly state the
desired operation. Not all
voice commands are dis-
played in the function
menu.
To use this function, a sub-
scription to the connected
services is necessary. Con-
tact your Toyota dealer for
details.

1865-1. Voice command system operation
Recognizable voice commands
and their actions are shown
below.
Frequently used commands
are listed in the following
tables.
 For devices that are not
installed to the vehicle, com-
mands relating to that device
may not be displayed on the
screen. Also, depending on
other conditions, such as
compatibility, some com-
mands may not be displayed
on the screen.
 The functions available may
vary according to the system
installed.
 Voice recognition language
can be changed. ( P.60)
 When an Apple Car-
Play/Android Auto connec-
tion is established, some
commands will become
unavailable.
■Common
■Top menu
*: Vehicle must be parked
Command list
Command list overview
Command list
CommandAction
“Help”
Displays exam-
ples of some of
the available
commands
“Go back”Returns to the
previous screen
“Cancel”
Cancels the
voice command
system
“Start over”Returns to top
menu screen
“Pause”
Temporarily
pauses a voice
session until it is
resumed by
pressing the talk
switch again.
CommandAction
“Show com-
mand examples
for <menu>”Displays the
command list of
the selected
menu
“More com-
mands”Displays more
commonly used
commands
“Voice settings”Displays Voice
Setting screen
“Train my voice”
Displays Train
Voice Recogni-
tion screen
*

1875-1. Voice command system operation
5
Voice command system
■Navigation*1
*1: Premium Audio only
*2: English and French only
*3: Best recognition results occur
when saying the full address
without the zipcode
*4: When the language is set to French, the supported area is
only Quebec Province in Canada
*5: For example; “Ga s stations”,
“Restaurants”, etc.
*6: Major national brands are always supported. Local brands are also
supported with a subscription to
the connected services. Contact
your Toyota dealer for details.
*7: When the language is set to French, the supported area is
only Quebec City in Canada
*8: Used when multiple destinations are set on a route
CommandAction
“Get directions to
<house #, street,
city, state>”
*2
Enables setting
a destination by
saying the
address
*3, 4
“Find a <POI cat-
egory/POI
name>”
Displays a list of
<POI cate-
gory
*5/POI
name
*6> near
the current posi-
tion
“Find a <POI>
near my destina-
tion”Displays a list of
<POI> near the
destination
“Find a <POI cat-
egory> in a
city”
*2
Displays a list of
<POI> in a spec-
ified city and
state
*7
“Go home”Displays the
route to home
“Go to favorite
<1-10>”
Sets the location
registered to the
corresponding
favorite number
as the destina-
tion
“Show recent
destinations”
Displays recent
destinations.
Selecting a num-
ber from the list
will start naviga-
tion to the
selected recent
destination.
“Cancel route”Cancels the
route guidance
“Delete destina-
tions”Displays a list of
destination to
delete
*8
“Show <POI cat-
egory> icons”
Displays the
specified point of
interest cate-
gory
*5 icons on
the map
CommandAction