light VOLVO V60 2014 Owners Manual

10 Maintenance and service
10
357
Lamp replacement - location of rear lamps
The overview shows the location of the lamps at the rear.
Brake light (LED)
Position/parking lamps (LED)/Side marker lamps (LED)
Indicator (p. 356)
Brake light (LED)
Reversing lamp
Rear fog lamp
Related information
•Lamp replacement (p. 352)
• Lamps - specifications (p. 358)
Lamp replacement - number plate lighting
The number plate lighting is located under the tailgate handle.
1. Remove the screws with a screwdriver.
2. Carefully detach the whole lamp housing
and withdraw it.
3. Replace the bulb.
4. Refit the whole lamp housing and screw it into place.
Related information
• Lamps - specifications (p. 358)
Lamp replacement - lighting in cargo area
The cargo area lighting is located in the tail- gate.
G031942
1. Insert a screwdriver and gently prize so
that the lamp housing comes loose.
2. Replace the bulb.
3. Check that the bulb illuminates and press back the lamp housing.
Related information
• Lamps - specifications (p. 358)
ProCarManuals.co’

10 Maintenance and service
10
358
Lamp replacement - vanity mirror lighting
The vanity mirror's lamps are fitted inside the lamp lenses.
Removal of lamp lens
1. Insert a screwdriver under the lamp lensand gently prize up the lug on the edge.
2. Carefully detach and lift aside the lamp lens.
3. Use needle-nose pliers to pull the bulb straight out to the side and replace with a new one. Note! - Do not pinch hard withthe pliers. Otherwise the lamp lens couldthen be crushed.
Attaching the lamp lens1. Refit the lamp lens.
2. Press it into place.
Related information
• Lamps - specifications (p. 358)
Lamps - specifications
The specifications apply to bulbs. When replacing LED and Xenon lamps, please referto a workshop.
LightingWAType
Dipped beam, halogen55H7 LL
Main beam, Halo- gen65H9
Extra main beam, ABL65H9
Front direction indicators24PY24W
Courtesy lighting front3T10 Socket
W2.1x9.5d
Glovebox lighting5Socket SV8.5
Length 43 mm
Vanity mirror lighting1,2T5 Socket W2x4.6d
Cargo area light- ing5Socket SV8.5
Length 43 mm
Number plate lighting5C5W LL
Direction indica- tors, rear21PY21W LL
ProCarManuals.co’

10 Maintenance and service
10
359
LightingWAType
–––
Reversing lamp21P21W LL
Rear fog lamp21H21W LL
A
Watt
Related information
• Lamp replacement (p. 352)
• Lamp replacement - location of rear lamps (p. 357)
• Lamp replacement - vanity mirror lighting(p. 358)
Wiper blades
The wiper blades sweep water away from the windscreen and rear window. Together withthe washer fluid they clean the windows andensure visibility for driving. The windscreen wiper blades must be in serv- ice position when they are to be replaced.
Service position
Wiper blades in service position.
In order to make replacement possible, to clean or lift the wiper blades (for scraping office from the windscreen, for example), theymust be in service position.
IMPORTANT
Before placing the wiper blades in the service position, make sure that they arenot frozen down.
1. Place the remote control key in the igni- tion lock 11
and briefly press the START/
STOP ENGINE button to set the car's
electrical system to key position I. For
detailed information on key positions, see Key positions - functions at different lev-els (p. 70).
2. Briefly press the START/STOP ENGINE
button again to set the car’s electricalsystem in key position 0.
3. Within 3 seconds, move the right stalk switch up and hold it in position forapprox. 1 second.
> The wipers then move to standingstraight up.
The wipers return to their starting position when you briefly press the START/STOP
ENGINE button to set the car’s electrical sys-
tem to key position I (or when the car is
started).
11 Not necessary in cars with Keyless function.
ProCarManuals.co’

10 Maintenance and service
10
}}
* Option/accessory, for more information, see Introduction.369
General fuses, engine compartmentOn the inside of the cover there are tweezers that facilitate the procedure for the removaland fitting of fuses.
Positions (see preceding illustration)Engine compartment, upper
Engine compartment, front
Engine compartment, lower
These fuses are all located in the engine com- partment box. The fuses in (C) are locatedunder (A). On the inside of the cover is a label that shows the location of the fuses. • Fuses 1-7 and 42-44 are of the "Midi Fuse" type and must only be replaced by a workshop 15
.
• Fuses 8-15 and 34 are of the "JCASE" type and should be replaced by a work- shop 15
• Fuses 16-33 and 35-41 are of the "Mini Fuse" type.
FunctionA
Primary fuse for the central electronic module (CEM) under the glovebox A50
Primary fuse for the central electronic module (CEM) underthe glovebox50
Primary fuse for central electri- cal unit in cargo area
A60
Primary fuse for relay/fuse box under the gloveboxA60
Primary fuse for relay/fuse box under the gloveboxA60
––
Electric additional heater* A100
Heated windscreen*, left-hand side40
Windscreen wipers30
Parking heater*25
Ventilation fanA40
Heated windscreen*, right- hand side40
FunctionA
ABS pump40
ABS valves20
Headlamp washer*20
Headlamp levelling*; Active Xenon headlamps - ABL*10
Primary fuse for the central electronic module (CEM) underthe glovebox20
ABS5
Adjustable steering force*5
Engine control module; Trans- mission control module; Air-bags10
Heated washer nozzles*10
––
Light switches5
––
––
––
15
An authorised Volvo workshop is recommended.
ProCarManuals.co’

10 Maintenance and service
10
* Option/accessory, for more information, see Introduction.373
FunctionA
––
Infotainment control module; Screen A5
Audio control unit (amplifier)*, Digital radio*; TV*10
Audio or Control Module Sen- sus
A15
Telematics*; Bluetooth*5
––
Sunroof*; Interior lighting roof; Climate sensor*; Dampermotors, air intake5
12 V socket, tunnel console15
Seat heating, rear right*15
Seat heating, rear left*15
Electric additional heater*5
Seat heating (passenger side)15
Seat heating (driver's side)15
FunctionA
Parking assistance*; Parking camera*; Towbar control mod-ule* BLIS*5
AWD control module*15
Active chassis - Four-C*10
A
Certain model variants.
Related information
• Fuses - in engine compartment (p. 368)
• Fuses - in the control module under the glovebox (p. 374)
• Fuses - in cargo area (p. 376)
• Fuses - in the engine compartment's coldzone (p. 377)
ProCarManuals.co’

10 Maintenance and service
10
374* Option/accessory, for more information, see Introduction.
Fuses - in the control module under the glovebox
Fuses in the control module under the glove- box protect airbag and collision warning sys-tem functions, amongst other things.
Positions
FunctionA
Rear window wiper15
––
Interior lighting; Driver's door control panel, power windows;Remote controlled garage dooropener*; Power seats, front*7,5
FunctionA
Combined instrument panel5
Adaptive cruise control, ACC*; collision warning system*10
Interior lighting; Rain sensor7,5
Steering wheel module7,5
Central locking system, fuel filler flap10
FunctionA
Heated steering wheel*15
Heated windscreen*15
Unlocking, tailgate10
Folding head restraint*10
Fuel pump20
ProCarManuals.co’

10 Maintenance and service
10
* Option/accessory, for more information, see Introduction.375
FunctionA
Movement detector alarm*; Cli- mate panel5
Steering lock15
Siren*; Data link connector OBDII5
––
Airbags10
Collision warning*5
Accelerator pedal sensor; Dim- ming interior rearview mirror*;Seat heating, rear* Electric additional heater*7,5
Infotainment control module (Performance); Audio (Perform-ance)15
Brake lights5
Sunroof*20
Immobiliser5
Related information
• Fuses - in engine compartment (p. 368)
• Fuses - under glovebox (p. 372)
• Fuses - in cargo area (p. 376) •
Fuses - in the engine compartment's cold zone (p. 377)
ProCarManuals.co’

10 Maintenance and service
10
}}
379
Car washing
The car should be washed as soon as it becomes dirty. Wash the car in a car washwith oil separator. Use car shampoo.
Washing by hand
•Remove bird droppings from the paint- work as soon as possible. Bird droppingscontain chemicals that affect and discol-our paintwork very quickly. An authorisedVolvo workshop is recommended for theremoval of any discoloration.
• Hose down the underbody.
• Rinse the entire car until the dissolved dirthas been removed so as to reduce therisk of scratches from washing. Do notspray directly onto the locks.
• If necessary, use cold degreasing agenton very dirty surfaces. Note that in thiscase, the surfaces must not be hot fromthe sun!
• Wash using a sponge, car shampoo andplenty of lukewarm water.
• Clean the wiper blades with a lukewarmsoap solution or car shampoo.
• Dry the car using a clean, soft chamois ora water scraper. If you avoid allowingdrops of water to dry in strong sunlight,you reduce the risk of water drying stainswhich may need to be polished out.
WARNING
Always have the engine cleaned by a workshop. There is a risk of fire if theengine is hot.
IMPORTANT
Dirty headlamps have impaired functional- ity. Clean them regularly, when refuellingfor example. Do not use any corrosive cleaning agents but use water and a non-scratchingsponge instead.
NOTE
Outside lighting such as headlamps, fog lamps and rear lamps may temporarilyhave condensation on the inside of thelens. This is normal, all exterior lighting isdesigned to withstand this. Condensationis normally vented out of the lamp housingwhen the lamp has been switched on for atime.
Wiper bladesAsphalt, dust and salt residue on wiper blades, as well as insects, ice etc. on thewindscreen, impair the service life of wiperblades. For cleaning:- Set the wiper blades to the service position, see Wiper blades (p. 359).
NOTE
Wash the wiper blades and windscreen regularly with lukewarm soap solution orcar shampoo. Do not use any strong sol-vents.
Automatic car washesAn automatic car wash is a simple and quick way of washing the car, but it cannot reacheverywhere. Handwashing the car is recom-mended for achieving optimum results.
NOTE
The car must only be washed by hand over the first few months. This is becausethe paint is more delicate when it is new.
High-pressure washingWhen using high-pressure washing, use sweeping movements and make sure that thenozzle does not come closer than 30 cm tothe surface of the car (the distance applies toall exterior parts). Do not spray directly ontothe locks.
ProCarManuals.co’

||
10 Maintenance and service
10
380
Testing the brakes
WARNING
Always test the brakes after washing the car, including the parking brake, to ensurethat moisture and corrosion do not attackthe brake linings and reduce braking per-formance.
Lightly depress the brake pedal now and then when driving long distances in rain or slush.The heat from the friction causes the brakelinings to warm up and dry. Do the samething after starting in very damp or coldweather.
Exterior plastic, rubber and trim
components
A special cleaning agent available from Volvodealers is recommended for the cleaning andcare of coloured plastic parts, rubber and trimcomponents, such as glossy trim mouldings.When using such a cleaning agent theinstructions must be followed carefully.
IMPORTANT
Avoid waxing and polishing on plastic and rubber. When using degreasant on plastic and rubber, only rub with light pressure if it isnecessary. Use a soft washing sponge. Polishing glossy trim mouldings could wear away or damage the glossy surfacelayer. Polishing agent that contains abrasive must not be used.
RimsOnly use rim cleaning agent recommended by Volvo. Strong rim cleaning agents can damage the surface and cause stains on chrome-platedaluminium rims.
Related information
• Polishing and waxing (p. 380)
• Cleaning the interior (p. 381)
• Water and dirt-repellent coating (p. 381)
Polishing and waxing
Polish and wax the car if the paintwork is dull or to give the paintwork extra protection. The car does not need to be polished until it is at least one year old. However, the car canbe waxed during this time. Do not polish orwax the car in direct sunlight. Wash and dry the car thoroughly before you begin polishing or waxing. Clean off asphaltand tar stains using tar remover or white spi-rit. More stubborn stains can be removedusing fine rubbing paste designed for carpaintwork. Polish first with a polish and then wax with liquid or solid wax. Follow the instructions onthe packaging carefully. Many preparationscontain both polish and wax.
IMPORTANT
Only paint treatment recommended by Volvo should be used. Other treatmentsuch as preserving, sealing, protection,lustre sealing or similar could damage thepaintwork. Paintwork damage caused bysuch treatments is not covered by Volvowarranty.
Related information
• Car washing (p. 379)
ProCarManuals.co’

10 Maintenance and service
10
383
Group 3
(dry dirt, dust)
1. Use a soft brush to remove the dirt.
2. Same procedure as for group 1.
Stains on interior plastic parts, metal parts and wood parts
A fibrillated fibre or microfibre cloth, lightly moistened with water, available from Volvodealers, is recommended for cleaning interiorparts and surfaces. Do not scrape or rub stains. Never use strong stain removers. A special cleaning agentavailable from Volvo dealers can be used formore difficult cleaning.
SeatbeltsUse water and a synthetic detergent. A spe-cial textile cleaning agent is available fromyour Volvo dealer. Make sure the seatbelt isdry before allowing it to retract.
Related information
• Car washing (p. 379)
Paint damage
Paint is an important part of the car's rust- proofing and should therefore be checkedregularly. The most common types of paint-work damage are stone chips, scratches, andmarks on the edges of wings, doors andbumpers.
Touching up minor paintwork damageTo avoid the onset of rust, damaged paint-work should be rectified immediately. Materials
• primer 17
- a special adhesive primer in a
spray can is available for e.g. plastic- coated bumpers
• basecoat and clearcoat - available in spray cans or as touch-up pens/sticks 18
• masking tape
• fine sand paper 17
.
Colour code
Code for the car's colour
It is important that the correct colour is used. For product label location, see Type designa-tions (p. 386).
17 If required.
18 Follow the instructions that are included with the package for the touch-up pen/stick.
ProCarManuals.co’