VOLVO XC90 2014 Owner´s Manual

02 Instruments and controls
HomeLink®
Wireless Control System*
02
* Option/accessory, for more information, see Introduction.89
Introduction
G030070
The HomeLink 1
Wireless Control System pro-
vides a convenient way to replace up to three hand-held radio-frequency (RF) transmittersused to activate devices such as gate opera-tors, garage door openers, entry door locks,security systems, even home lighting. Addi-tional HomeLink information can be found onthe Internet at www.homelink.com or byphoning the hotline at 1–800–355–3515.
WARNING
• If you use HomeLink to open a garage door or gate, be sure no one is nearthe gate or door while it is in motion.
• When programming a garage dooropener, it is advised to park outside ofthe garage.
• Do not use HomeLink with any garagedoor opener that lacks safety stop andreverse features as required by U.S.federal safety standards (this includesany garage door opener model manu-factured before April 1, 1982). Agarage door that cannot detect anobject - signaling the door to stop andreverse - does not meet current U.S.federal safety standards. For moreinformation, contact HomeLink at:www.homelink.com.
Retain the original transmitter of the RF device you are programming for use in othervehicles as well as for future HomeLink pro-gramming. It is also suggested that upon thesale of the vehicle, the programmed Home-Link buttons be erased for security purposes.Refer to “Resetting HomeLink Buttons” onpage 91.
Programming HomeLink
NOTE
Some vehicles may require the ignition to be switched on or be in the “accessories”position for programming and/or operationof HomeLink. It is also recommended thata new battery be placed in the hand-heldtransmitter of the device being pro-grammed to HomeLink for quicker trainingand accurate transmission of the radio-fre-quency signal. The HomeLink buttonsmust be reset first. When this has beencompleted, Homelink is in learning modeso that you can perform programming.
1. Position the end of your hand-held trans-
mitter 1–3 inches (5–14 cm) away from the HomeLink button you wish to pro-gram while keeping the indicator light inview.
2. Simultaneously press and hold both the chosen HomeLink and hand-held trans-mitter buttons until the HomeLink indica-tor light changes from a slow to a rapidlyblinking light. Now you may release boththe HomeLink and hand-held transmitterbuttons.
1HomeLink and the HomeLink house are registered trademarks of Johnson Controls, Inc.

02 Instruments and controls
HomeLink®
Wireless Control System*
02
90* Option/accessory, for more information, see Introduction.
NOTE
Some devices may require you to replace this Programming Step 2 with proceduresnoted in the “Gate Operator / CanadianProgramming” section. If the HomeLinkindicator light does not change to a rapidlyblinking light after performing these steps,contact HomeLink at www.homelink.comor by phoning the hotline at1–800–355–3515.
3. Firmly press, hold for five seconds and
release the programmed HomeLink but-
ton up to two separate times to activate the door. If the door does not activate,press and hold the just-trained HomeLinkbutton and observe the indicator light.
• If the indicator light
stays on con-
stantly, programming is complete and your device should activate when the HomeLink button is pressed andreleased.
• If the indicator light blinks
rapidly for
two seconds and then turns to aconstant light continue with “Pro- gramming” steps 4-6 to complete the
programming of a rolling code equip- ped device (most commonly a garagedoor opener). 4. At the garage door opener receiver
(motor-head unit) in the garage, locate the “learn” or “smart” button. This canusually be found where the hangingantenna wire is attached to the motor-head unit.
5. Firmly press and release the “learn” or “smart” button. (The name and color ofthe button may vary by manufacturer.)There are 30 seconds to initiate step 6.
6. Return to the vehicle and firmly press, hold for two seconds and release the pro-grammed HomeLink button. Repeat the“press/hold/release” sequence a secondtime, and, depending on the brand of thegarage door opener (or other rolling codeequipped device), repeat this sequence athird time to complete the programmingprocess.
HomeLink should now activate your rollingcode equipped device.
Gate Operator/Canadian ProgrammingCanadian radio-frequency laws require trans-mitter signals to “time-out” (or quit) after sev-eral seconds of transmission – which may notbe long enough for HomeLink to pick up thesignal during programming. Similar to thisCanadian law, some U.S. gate operators aredesigned to “time-out” in the same manner. If you live in Canada or you are having diffi-culties programming a gate operator orgarage door opener by using the “Program-ming” procedures,
replace “Programming
HomeLink” step 2 with the following :
• Continue to press and hold the HomeLink button while you
press and release -
every two seconds (“cycle”) your hand-
held transmitter until the HomeLink indi-cator light changes from a slow to a rap-idly blinking light. Now you may releaseboth the HomeLink and hand-held trans-mitter buttons.
Proceed with “Programming” step 3 to com- plete.
Using HomeLink
To operate, simply press and hold the pro- grammed HomeLink button until the traineddevice begins to operate (this may take sev-eral seconds). Activation will now occur forthe trained device (i.e., garage door opener,gate operator, security system, entry doorlock, home/office lighting, etc.). For conven-ience, the hand-held transmitter of the devicemay also be used at any time. In the eventthat there are still programming difficulties orquestions, contact HomeLink at:www.homelink.com or by phoning the hotlineat 1–800–355–3515.

02 Instruments and controls
HomeLink®
Wireless Control System*
02
* Option/accessory, for more information, see Introduction.91
NOTE
If the ignition is switched off, HomeLink will function for 30 minutes after the driv-er's door has been opened.
Resetting HomeLink Buttons
Use the following procedure to reset (erase programming) from the three HomeLink but-tons (individual buttons cannot be reset butcan be “reprogrammed” as outlined in the fol-lowing section):
1. Press and hold the two outer HomeLink
buttons until the indicator light begins to flash.
2. Release both buttons. > HomeLink is now in the training (orlearning) mode and can be pro-grammed at any time beginning with“Programming” - step 1.
Reprogramming a Single HomeLink Button
To program a device to HomeLink using a HomeLink button previously trained, followthese steps:
1. Press and hold the desired HomeLink button. DO NOT release the button.
2. The indicator light will begin to flash after 20 seconds. Without releasing the Home- Link button, proceed with “Programming”- step 1.
For questions or comments, contact Home-Link at: www.homelink.com or phone 1–800–355–3515. This device complies with FCC rules part 15 and Industry Canada (IC) RSS-210. Operationis subject to the following two conditions: (1)This device may not cause harmful interfer-ence, and (2) This device must accept anyinterference that may be received includinginterference that may cause undesired opera-tion.
NOTE
The transmitter has been tested and com- plies with FCC and IC rules. Changes ormodifications not expressly approved bythe party responsible for compliance couldvoid the user’s authority to operate the device. 2
2
The term “IC:” before the certification/registration number only signifies that Industry Canada technical specifications were met.

92
Climate control system – general information........................................ 94 Air distribution......................................................................................... 96
Electronic climate control (ECC)............................................................. 98

C L I M A T E

03 Climate
Climate control system – general information
03
94* Option/accessory, for more information, see Introduction.
Condensation on the inside of the windows
Keeping the insides of the windows clean will help reduce the amount of condensation thatforms on the windows. Use a commercialwindow cleaning agent to clean the windows.
Ice and snow
Always keep the air intake grille at the base of the windshield free of snow.
Cabin air filter
Replace the cabin air filter with a new one at the recommended intervals. Please refer toyour Warranty and Service Records Informa-tion booklet, or consult a trained and qualifiedVolvo service technician for these intervals.The filter should be replaced more often whendriving under dirty and dusty conditions. Thefilter cannot be cleaned and therefore shouldalways be replaced with a new one.
Sensors
The sunlight sensor on the dashboard and passenger compartment temperature sensorin the ECC control panel should not be cov-ered in any way as this could cause incorrectinformation to be sent to the ECC system.
Parking the vehicle in warm weather
If your vehicle has been parked in the sun in warm weather, opening the windows andmoonroof* for several minutes before drivingwill help release the warm air from the pas-senger compartment. When the engine is run-ning, close the windows and moonroof anduse the recirculation function for severalminutes to enable the air conditioning to coolthe compartment as quickly as possible.
Windows and optional moonroof
The ECC system will function best if the win- dows and optional moonroof are closed. Ifyou drive with the moonroof open, we recom-mend that you manually adjust the tempera-ture and blower control (the LED in the AUTO
switch should be off).
Acceleration
The air conditioning is momentarily disen- gaged during full-throttle acceleration.
Climate control maintenance
Special tools and equipment are required to maintain and carry out repairs on the climatesystem. Work of this type should only bedone by a trained and qualified Volvo servicetechnician.
Refrigerant
Volvo cares about the environment. The air conditioning system in your vehicle containsa CFC-free refrigerant – R134a (HFC134a).This substance will not deplete the ozonelayer. The approximate amount of R134acontained in the system is a follows: 6-cylinder engine Single A/C system: 1.5 lbs (700 g) Dual 1
A/C system: 2.2 lbs (1000 g)
The system also uses PAG oil.
1 Includes the optional rear A/C system

03 Climate
Climate control system – general information
03
95
Climate system blower
The climate system blower will be automati- cally switched off when the engine is not run-ning (even if the ignition key is in position I or
II ) to avoid unnecessary battery drain. To
activate the blower, turn the control to thedesired setting. The climate system blower may start auto- matically during a period of up to approxi-mately 50 minutes after the ignition has beenturned off to remove condensation in the A/Cevaporator. It will run for 15 minutes andswitch off automatically.
Passenger compartment blower
Approximately 50 minutes after the ignition is turned off, the blower may come on automati-cally, and run for seven minutes, to removecondensation in the A/C evaporator.
Blower function to reduce battery drain
The climate system's blower functions nor- mally while the engine is running. However, when the engine is switched off (even if the ignition is switched to positions I
or II), the blower control will be automatically
switched off to avoid unnecessary batterydrain. The following points pertain if the ignition ison but the engine in not running:
• To restart the blower, turn the control knob to the setting of your choice.
• After approximately 2 minutes, the blowerspeed will be reduced to avoid batterydrain.
You can reset the blower speed at any time. Please be aware that the system has beendesigned to reduce the blower's speed againafter 2 minutes, until the engine is started. If the battery becomes drained: • LOW BATTERY, FAN IS REDUCED
will
be displayed in the text window in the instrument panel.
• The yellow warning light in the instrumentpanel (see page 58) will also light up.

03 Climate
Air distribution
03
96
G027044
Air distributionThe incoming air is distributed through the ventilation points in the passenger compart-ment shown above.
G027043
Air vents in the dashOpen
Closed
Horizontal air flow
Vertical air flow
Direct the outer air vents toward the side win- dows to defrost.
0
G027064
Air vents in the door pillarsOpen
Closed
Horizontal air flow
Vertical air flow
Direct the outer air vents toward the side win- dows to defrost.

03 Climate
Air distribution
03
* Option/accessory, for more information, see Introduction.97
Ventilated front seats*
G030244
Controls for ventilated front seats
The ventilation system consists of fans in the seats and backrests that draw air through theseat upholstery. The cooling effect increasesas the air in the passenger compartmentbecomes cooler. The level of ventilation is adjusted on the con- trol panel on the side of the seat. The fanscan be set to three speeds. To start seat ventilation:
–Press briefly on .
To gradually increase ventilation:
–Press briefly on . For maximum ventilation:
–Hold down for approximately 2 sec-
onds.
To gradually decrease ventilation:
–Press briefly on .
To switch off ventilation:
–Hold down for approximately 2 sec-
onds.
The ventilation can be used at the same time as seat heating*, for example, to help drydamp clothing.
NOTE
• Seat ventilation cannot be started if the temperature in the passenger com-partment is below 41°F (5°C).
• Seat ventilation should be used withcaution by people who are sensitive todrafts. A moderate ventilation levelshould be set if the function is used forextended periods.

03 Climate
Electronic climate control (ECC)
03
98* Option/accessory, for more information, see Introduction.
Overview
AC – (ON /OFF )
Recirculation/Multifilter with sensor*
Recirculation
AUTO
Air distribution
Passenger compartment temperature sensor
Defroster windshield and side windows
Rear window and door mirrors defroster
Heated front seats*
Temperature passenger´s side
Temperature driver´s side
Blower
Blower control for rear climate system*
Functions
A/C – ON/OFF
•The air conditioning functions only at temperatures above 32°F (0°C).
• While the Defroster function is selected,the air conditioning is temporarily acti-vated to dehumidify the air, even if youhave manually switched the air condition- ing off. This will only function if the bloweris not switched off.
Press the switch to turn the air conditioning on or off. The " ON" or " OFF" LED will light up
to indicate if the system is switched on or off.Other functions will still be regulated auto-matically (if the AUTO switch is on).
Interior air quality sensor*
Some vehicles are equipped with a multifilter and air quality sensor. The filter separatesgases and particles, thereby reducing theamounts of odors and contaminants enteringthe vehicle. The air quality sensor detectsincreased levels of contaminants in the out-side air. When the air quality sensor detects