ECU ASTON MARTIN V8 VANTAGE 2010 Workshop Manual

Convertible Roof (01.17)
Body System (01.00)
May 2007 Workshop Manual 1-12-69
7. Open luggage compartment. secure velcro straps x2 and drain tubes x3.
8. Install front liner.
9. Close luggage compartment.
RH/LH Flex Shaft - Renew
Removal
10. Remove header panel assembly (see Workshop Manual procedure 01.05.BB Panel Assembly - Header - Renew).
11. Release insulation from header latch motor (see Figure 1).
12. Release flex shaft from centre securing clip (see Figure 2).
13. Release flex shaft from motor splines.
14. Release flex shaft from latch splines and remove.
Installation
1. Ensure header motor and latch are in fully open position prior to installation.
2. Align flex shaft on latch splines and install.
3. Align flex shaft to motor splines and install.
4. Secure flex shaft to centre securing clip.
5. Secure insulation to header latch motor.
6. Install header panel assemb ly (see Workshop Manual
procedure 01.05.BB Panel Assembly - Header - Renew).
Repair Operation Time (ROT)

Bumpers (01.19)
Body System (01.00)1-13-2 Workshop Manual May 2007
Specifications
Maintenance
Front Bumper Cover - Renew
Removal
1. Raise vehicle on ramp.
2. Remove front number plate and plinth (see Workshop Manual procedure 01.19.BD Licence Plate - Plinth
Assembly - Front - Renew).
3. Remove valance (see Workshop Manual procedure 01.19.AF Panel - Front Valance - Renew).
4. Remove screws (x2) securing front of undertray to bumper (see Figure 1).
5. Remove screws (x5) LH front wheel arch liner to bumper.
6. Remove screws (x5) RH front wheel arch liner to bumper.
7. Remove bolts (x3 securing LH air box to mounting brackets.
8. Remove bolts (x3 securing RH air box to mounting brackets. 9. Remove bolts (x6) securing bumper to front wing (see
Figure 2)
.
10. With assistance, release bumper from clips (x2) and
remove bumper (see Figure 3).
11. Remove mesh (clips x8).
Installation
1. Install mesh (clips x8).
2. With assistance position bumper and secure in clips (x2).
3. Install bolts (x6) bumper to front wing.
4. Install bolts (x3 securing RH air box to mounting brackets.
5. Install bolts (x3 securing LH air box to mounting brackets.
6. Install screws (x5) LH front wheel arch liner to bumper.
7. Install screws (x5) RH front wheel arch liner to bumper.
8. Install screws (x2) securing front undertray to bumper.
Torque Figures
DescriptionNm
Front Bumper to bumper bracket 4-5
Rear Bumper to Bumper Bracket 2-3
Repair Operation Time (ROT)
01-19-005
Figure 2
Figure 3
Remove Bolts x6
Front Bumper
01-19-001
01-19-004

Bumpers (01.19)
Body System (01.00)
May 2007 Workshop Manual 1-13-3
9. Install number plate and plinth (see Workshop Manual procedure 01.19.BD Licence Plate - Plinth Assembly -
Front - Renew).
10. Install valance (see Workshop Manual procedure 01.19.AF Panel - Front Valance - Renew).
11. Lower vehicle on ramp.
Rear Bumper Cover - Renew
Removal
1. Raise vehicle on ramp.
2. Remove number plate.
3. Remove LH rear lamp assembly (see Workshop Manual procedure 17.03.AB Lamp Assembly (Rear) - LH
Renew).
4. Remove RH rear lamp assembly (see Workshop Manual procedure 17.03.BB XREF: 280 Lamp Assembly (Rear) -
RH Renew).
5. Remove wheel arch liner LH (see Workshop Manual procedure 01.02.JB Wheel Arch Liner - Rear - RH -
Renew).
6. Remove wheel arch liner RH (see Workshop Manual procedure 01.02.HB Wheel Arch Liner - Rear - LH -
Renew).
7. Remove tyre mobility kit from the rack.
8. Remove torx bolts located behind carpets to rear wings (x2).
9. Remove bolts (x2) in rear light recess.
10. Remove bolts securing bumper to wheel arch (6).
11. Remove bolts (x4) securing bumper to brackets.
12. With assistance Release bumper from body.
13. Release fir trees securing harness to bumper (x6).
14. Release remaining harness clips from bumper (x6).
15. Disconnect multiplugs to parking aid sensors (x2).
16. Disconnect multiplugs to license plate lamps (x2).
17. Remove nuts (x6) securing exhaust finishers to bumper.
18. Remove number plate light assembly (clips x5).
19. Remove parking aid sensors (x2)
20. Remove screw retaining clips (x13)
Installation
1. Install screw retaining clips x13.
2. Install parking aid sensors x2.
3. Install number pl ate light assembly
4. Install exhaust finishers to bumper.
5. With assistance position bumper to body.
6. Connect multiplugs to license plate lamps X2.
7. Connect multiplug to parking aid sensors.
8. Secure harness to bumper (f ir trees x6 and clips x6)
9. Install bumper bolts to brackets and body (x10). 10. Install tyre mobility kit to rack.
11. Install number plate.
12. Install RH rear lamp asse
mbly (see Workshop Manual
procedure 17.03.BB Lamp Assembly (Rear) - RH
Renew).
13. Install LH rear lamp assembly (see Workshop Manual procedure 17.03.AB Lamp Assembly (Rear) - LH
Renew).
14. Install wheel arch liner LH (see Workshop Manual procedure 01.02.JB Wheel Arch Liner - Rear - RH -
Renew).
15. Install RH wheel arch li ner (see Workshop Manual
procedure 01.02.HB Wheel Arch Liner - Rear - RH -
Renew).
16. Lower vehicle on ramp.
Repair Operation Time (ROT)

Restraining Devices (01.20)
Body System (01.00)
May 2007 Workshop Manual 1-14-1
Body System (01.00)
Restraining Devices (01.20)
Seat Belts
This vehicle is installed with two inertia reel safety belts. The
inertia belt reels automatically tension the belts to provide
security with comfort. In the event of a collision or during
severe braking, the belt reels will lock.
The driver and front passenger safety belt buckles are
installed with a switch, which is connected to a warning
indicator housed within the DIM. When the ignition is first
turned on the warning indicator will illuminate only if the
seat belt is not fastened. If the safety belt is fastened before
the ignition is turned on the circuit is broken and the
indicator will remain off.
Pre-tensioner and Load Limiting Systems
The driver and front passenger seat belts are equipped with
pre-tensioner and load limiting systems. In most moderate frontal or near frontal accidents, the front
airbag and pre-tensioner syst
ems will deploy simultaneously.
The pre-tensioners take up slack in the front seat belts as the
airbags are expanding. The load limiting system releases belt
webbing in a controlled manner to reduce belt force on the
occupant’s chest.
The RCM receives information on the status of the safety belt
buckles from a switch contained in the buckle. Only
fastened safety belts will activate.
The safety belt retractors, which are mounted within the
base of the B pillars, incorporate a torsion bar load limiting
device. This device consists of a retractor reel which is



In some moderate frontal or ne ar frontal accidents, only the
pre-tensioner system will deploy.

Restraining Devices (01.20)
Body System (01.00)1-14-2 Workshop Manual May 2007
mounted onto a spindle (torsion bar) which once the sensor
has locked the retractor reel and a predetermined load is
applied, twists and allows additional webbing into the
system. The deceleration force required to initiate this
sequence is approximately th e same as that required to
initiate airbag deployment. The torsion bar load limiting
device will only react if the safety belt is in use at the time of
the impact.
Emergency Locking Retractor (ELR)
The retractors in all seat posi tions feature ELR. During any
period of sudden deceleration, or under lateral load when
cornering at speed, a sensor weight within the safety belt
retractor moves a locking pawl against the teeth on the
retractor reel, which then locks the retractor preventing any
further release of webbing. As soon as the load applied onto
the retractor through the safety belt webbing is removed the
locking pawl releases the retractor reel and normal
movement is returned to the retractor.
Automatic Locking Retractor (ALR)
Automatic locking retractors (ALR) are installed to all
passenger seat positions.
The safety belt webbing on these are clearly marked to show
their operating feature. To initiate the ALR system, fasten the
safety belt into it’s buckle and pull all of the webbing from
the retractor, as the safety belt is released the retractor locks
allowing travel in only one plane thus producing a fixed
length restraint and preventing the safety belt from
introducing slack, making any child seat it may be restraining
secure. The ALR system of the retractor is disengaged by
releasing the safety belt and allowing the safety belt to fully
retract onto the reel. Caution
It should be considered th at during any event that
utilizes the full capability of the safety belts, the
webbing may have been elongated and the torsion bar may have twisted. For this reason, if a vehicle is
involved in an accident which results in the deployment of the airbag(s), all the safety belts that were in use at
the time of the accident MUST be renewed.

Restraining Devices (01.20)
Body System (01.00)
May 2007 Workshop Manual 1-14-5
2. Remove sub woofer enclosure (see Workshop Manual procedure 15.03.GA Subwoofer Enclosure - Premium -
Renew).
3. Remove speaker grille.
4. Remove bolts (x2) and screw (x1) securing upper quarter trim moulding to body and rear bulkhead panel.
5. Feed seatbelt through trim moulding aperture and
remove moulding.
6. Remove foam cover, disconnect speaker multiplug, remove upper trim quarter moulding.
7. Remove bolts (x4) securing seat belt upper anchor
mounting plate (see Figure 1).
8. Release seat belt from anchor mounting plate, remove mounting plate.
9. Disconnect pre-tensioner mu ltiplug, release multiplug
from mounting bracket.
10. Remove bolts (x4) securing seat belt mounting bracket to body.
11. Remove seat belt assembly.
12. Remove bolt securing seat belt stalk to seat frame,
remove stalk.Installation
1. Position seat belt stalk to seat frame, install and torque tighten bolt.
2. Install seat belt assembly, in stall and torque tighten bolts
(x4).
3. Install seat belt in upper anchor mounting plate.
4. Position seat belt upper anchor mounting plate, install and torque tighten bolts (x4).
5. Connect pre-tensioner multip lug, secure multiplug in
mounting bracket.
6. Position quarter moulding, connect speaker multiplug, secure foam cover.
7. Feed seat belt harness th rough quarter trim moulding.
8. Install quarter trim moulding, install and tighten bolts (x3).
9. Install sub woofer enclos ure (see Workshop Manual
procedure 15.03.GA Subwoofer Enclosure - Premium -
Renew).
10. Install front seat (see Workshop Manual procedure 01.10.AB Seat Assembly - Front - LH - Remove for
Access and Refit).
RH Front Seat Belt - Renew
Removal
1. Remove front seat (see Workshop Manual procedure 01.10.AA Seat Assembly - Front - RH - Remove for
Access and Refit).
2. Remove moulding assembly - quartet trim upper - RH (see Workshop Manual proc edure 01.05.CL Moulding
Assembly - Quarter Trim Upper - RH - Renew).
3. Remove bolts (x5) securing seat belt upper anchor
mounting plate (see Figure 1).
4. Release seat belt from anchor mounting plate, remove mounting plate.
Figure 1
Figure 2
A0120184
A0120185
Repair Operation Time (ROT)
A0120186

Restraining Devices (01.20)
Body System (01.00)1-14-6 Workshop Manual May 2007
5. Disconnect pre-tensioner mu ltiplug, release multiplug
from mounting bracket (see Figure 2).
6. Release harness fir tree clips (x2) from seat belt mounting bracket.
7. Release main fuse clips from seat belt mounting bracket.
8. Remove bolts (x4) securing seat belt mounting bracket to body.
9. Remove seat belt assembly.
10. Remove bolt securing seat belt stalk to seat frame, remove stalk.
Installation
1. Position seat belt stalk to seat frame, install and torque tighten bolt.
2. Install seat belt assembly, in stall and torque tighten bolts
(x4).
3. Install seat belt in upper anchor mounting plate.
4. Position seat belt upper anchor mounting plate, install and torque tighten bolts (x5).
5. Install main fuse to mounting bracket.
6. Secure harness fir tree clips (x2) in mounting bracket.
7. Connect pre-tensioner multip lug, secure multiplug in
mounting bracket.
8. Install moulding assembly - quartet trim upper - LH (see Workshop Manual procedure 01.05.CL Moulding
Assembly - Quarter Trim Upper - RH - Renew).
9. Install front seat (see Workshop Manual procedure 01.10.AA Seat Assembly - Front - RH - Remove for
Access and Refit).
Passenger Airbag - Renew
Removal
1. Disconnect vehicle battery for minimum of 2 minutes.
2. Remove airbag panel and door assembly (see Workshop Manual procedure 01.12.AJ Panel and Door Assembly -
Air Bag - Renew).
3. Remove bolts (x4) securing airbag unit.
4. Disconnect multiplugs (x2), remove airbag unit.
Installation
1. Install airbag unit, install and tighten bolts (x4), connect multiplugs (x2).
2. Install airbag panel and d oor assembly (see Workshop
Manual procedure 01.12.AJ Panel and Door Assembly -
Air Bag - Renew).
3. Connect vehicle battery.
ARS Side Impact Sensor Assembly - B
Pillar-Renew
Removal
1. Remove plate - front sill - RH (see Workshop Manual procedure 01.05.AJ Plate - Front Sill - RH - Renew).
2. Pull back sill carpet sufficient to access side impact sensor.
3. Disconnect multiplug from side impact sensor (see Figure 1).
4. Remove screws (x2) securing side impact sensor to inner
sill, remove sensor.
Installation
1. Install side impact sensor, install and tighten screws (x2).
2. Connect multiplug to side impact sensor.
3. Re-position sill carpet.
4. Install plate - front sill - RH (see Workshop Manual procedure 01.05.AJ Plate - Front Sill - RH - Renew).
Side Impact Door ARS Sensor Assembly -
Renew
Figure 2
A0120187
Repair Operation Time (ROT)
ItemCode
Passenger Airbag -Renew 01.20.CA
Repair Operation Time (ROT)
ItemCode
ARS Side Impact Sensor Assembly-B-
pillar-Renew 01.20.DB
Repair Operation Time (ROT)
ItemCode
Side Impact Door ARS Sensor Assembly-
Renew 01.20.DD

Restraining Devices (01.20)
Body System (01.00)
May 2007 Workshop Manual 1-14-7
Removal
1. Remove door trimboard assembly (see Workshop Manual procedure 01.05.CB Trimboard Assembly -
Door - Remove for Access and Refit).
2. Remove door module securing bolts (x4), swing downwards.
3. Remove door impact sensor plate securing bolts (x3) and disconnect sensor multiplug (x1).
4. Remove sensor securing nuts (x2) from plate.
Installation
1. Install sensor on plate and secure nuts (x2).
2. Connect sensor multiplug (x1) and fit plate securing bolts (x3).
3. Install door module wi th securing bolts (x4).
4. Install door trimboard asse mbly (see Workshop Manual
procedure 01.05.CB Trimboard Assembly - Door -
Remove for Access and Refit).
Front Impact Sensor Assembly - Renew
Removal
1. Remove grille (see Workshop Manual procedure 01.08.AA Grille - Radiator - Renew).
2. Remove slam panel (bolts x12).
3. Remove bolts (x4) securing PAS oil cooler.
4. Remove bolts securing crossmember to inner wing (x4).
5. Remove bolts and spacers securing crossmember to wing (x2).
6. Move crossmember to one side and lift up clear of location (protect paintwork).
7. Disconnect multiplug from front impact assessor (see
Figure 1).
8. Remove screws (x2) securi ng front impact sensor to
cross member, remove sensor.
Installation
1. Install front impact sensor to cross member. install and tighten screws.
2. Connect multiplug to impact sensor.
3. Install crossmember (as removed).
4. Install bolts and spacers securing crossmember to wing (x2).
5. Install bolts securing cros smember to inner wing (x4).
6. Install bolts (x4) securing PAS oil cooler.
7. Install slam panel (bolts x12).
8. Install grille (see Workshop Manual procedure 01.08.AA
Grille - Radiator - Renew).
Occupant Restraint Control Module
Assembly - Renew
Removal
1. Remove rear centre console (see Workshop Manual procedure 01.12.CA Panel Assembly - Console - Rear -
Renew).
2. Release harness clip and disconnect front multiplug (x1) (see Figure 1).
Repair Operation Time (ROT)
A0120181
Repair Operation Time (ROT)
A0120180

Restraining Devices (01.20)
Body System (01.00)1-14-8 Workshop Manual May 2007
3. Remove nuts (x2) and bolts (x2) module to centre tunnel (see Figure 2). 4. Disconnect rear multiplug (x2) and remove module
occupant restraint (see Figure 3).
Installation
1. Connect rear multiplug (x1) occupant restraint module.
2. Install module.
3. Connect front multiplug (x1) and secure harness.
4. Install rear centre console (see Workshop Manual procedure 01.12.CA Panel As sembly - Console - Rear -
Renew).
RH/LH Roll Over Protection System -
Renew
Removal
1. Remove right-hand/left-hand rear body side trim (see Workshop Manual procedure 01.05.DX/01.05.DY Panel
Assembly - Bodyside Trim - Rear - RH/LH - Renew).
2. Remove right-hand/left-hand rear console panel assembly (see Workshop Ma nual procedure 01.12.DF/
01.12.DE Console Pa nel Assembly - Rear Roadster - RH/
LH - Renew).
Figure 2
A0120181A
Figure 3
Repair Operation Time (ROT)
ItemCode
Roll Over Protection System-Renew RH01.20.EA
Roll Over Protection System-Renew LH01.20.EB
A0120180B

Restraining Devices (01.20)
Body System (01.00)
May 2007 Workshop Manual 1-14-9
3. Release ROPS multiplug from body and disconnect (see Figure 1).
4. Remove 4 bolts securing upper Roll Over Protection System (ROPS) trim and remove.
5. Remove 6 bolts securing ROPS unit to body and remove (see Figure 2).
Installation
1. Install ROPS unit and secure with bolts.
2. Install upper ROPS trim and secure with bolts.
3. Connect ROPS multiplug and secure to body.
4. Install right-hand/left-hand rear console panel assembly (see Workshop Manual procedure 01.12.DF/01.12.DE
Console Panel Assembly - Rear Roadster - RH - Renew).
5. Install right-hand/left-hand rear body side trim (see Workshop Manual procedure 01.05.DX/01.05.DY Panel
Assembly - Bodyside Trim - Rear - RH/LH - Renew). Figure 1
Figure 2