ignition AUDI A3 CABRIOLET 2015 Owner's Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2015, Model line: A3 CABRIOLET, Model: AUDI A3 CABRIOLET 2015Pages: 302, PDF Size: 73.83 MB
Page 77 of 302

M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
When seat heating should not be
sw itch ed on
Do not turn the seat heating on under the fol
l owing circumstances:
- T he seat is unoccupied.
- T he seat is covered w ith a seat cover.
- The seat is covered w ith a ch ild seat .
- The seat is damp or wet .
A WARNING
Individuals with reduced sensitivity to pain
or temperatu re could develop burns when
using the seat heating function. To reduce
t he risk of inju ry, these individ uals should
not use seat heating.
(D Note
To avo id damage to the heating elements
in the seats, do not kneel on the seats or
p lace heavy loads on a small area of the
seat.
(D Tips
- The se tti ng fo r the seat heating on the
driver's side is assigned to the key that is
1 n use .
- If the fron t passenger's seat heating is
turned on, it will not turn on again auto
ma tically if more than
1 0 minutes have
passed between switching the ignition
off and switching it on aga in.
Warm and c old 75
•
Page 78 of 302

76 Driving
Driving
Steering
Adjusting the steering wheel position
The steering wheel position is fully adjustable
up and down and forward and bock .
Fig. 78 Steering column: stee ring column adjustmen t
lever
.. Tilt the lever ¢ fig. 78 downward ¢ &_.
.. Bring the steering wheel into the desired
position .
.. Push the lever against the steering column
until it latches .
_& WARNING
Incorrect use of the steer ing whee l adjust
ment and an incorrect seating position can
cause serious injuries.
- Only adjust the steering column when
the vehicle is stationary so that you do
not Lose control of the vehicle.
- Adjust the driver's seat or steering wheel
so that there is at least 10 inches
(25 cm) distance between your chest and
the steering wheel
r=.> page 12 7,
fig. 123. If you do not maintain this dis
tance, the airbag system will not be able
to provide its full protection
<=> page 127, fig. 123.
- If your physical characteristics prevent
you from sitting at least 10 inches
(25 cm) or more away from the steering
wheel, see if your authorized Audi dealer or authorized Audi Service Fac ility can
provide adapters that will help.
- If your face is level with the steering
wheel, the airbag does not provide as much protection during a collision. Al
ways make sure that the steering wheel
is level with your chest .
- Always hold the steering wheel with your
hands in the 9 o'clock and 3 o'clock posi
tions to reduce the risk of injury if the
airbag deploys.
- Never hold the steering wheel in the 12
o'clock position or with both hands on
the rim or the center of the steering
wheel. Holding the steering wheel incor
rectly significantly increases the r isk of
injury to the hands, arms and head if the
airbag deploys.
Starting and stopping
the engine (vehicles
with an ignition lock)
Starting the engine with the key
Applies to vehicles: wit h mechanical ignition loc k
The ignition is switched on and the engine
started with the key in the ignition.
Fig. 79 Ignit ion key positions
Steering lock
If the steering wheel will not turn, the steer
ing lock is engaged.
To engage the steering wheel Lock: The selec
tor lever must be in the P position.
"' To engage the steering wheel lock, turn the
wheel until it locks when the ignition key is
removed .
"' To release the steering wheel Lock, insert
the key in the ignition lock and turn the key
in the -direction of the arrow-whi le turning
the steering wheel. ""
Page 79 of 302

M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Switchin g th e ig nition on /off
"'T o sw itch the ignition on, turn the ignition
key to position
(D .
"'To switch the ignition off, turn the ignition
key to position @.
Starting the engin e
Your vehicle is equipped w ith launch cont ro l.
As soon as you have turned the ign ition key to
position @, the engine will start automatical
l y.
"' Press the brake peda l and move the se lector
lever to the P or N pos it ion.
"'T urn the key briefly to position @. The igni
t ion key automatically r eturns to posit ion
(D . Do not press the accelerator pedal wh en
doing this .
Major electrical equipment switches off tem
porarily when starting the eng ine.
If the engine does not sta rt immedia tely , stop
the starting procedure by turning the ignition key to position @and repeat after 30 sec
onds .
Automatic start m alfunction
If the ~ indicator l ight turns on (gasoline en
g ine) and the message
Engin e start sys te m
m alfu nction. Ple ase contac t Se rvice
appears ,
there is an automatic start ma lfunction.
To start t he eng ine, hold the ignition key in
position @until the engine runs .
Drive to an authorized Aud i dealer or author
ized Audi Service Facility immed iate ly to have
the ma lfunction corrected .
_& WARNING
-Never allow the engine to run in confined
spaces -there is a risk o f asphyxiation.
- Never remove the ign ition key from the
ignition lock whi le the vehicle is moving .
Otherw ise the steering lock wi ll engage
and you will not be able to steer the vehi
cle.
- Please note that the brake booster and
power steering only work when the en-
Dri vin g 77
gine is running. When the engine off, you
must use more force to steer or brake
the vehicle. Because the usual steering
and brak ing capability is not avai lab le,
the risk of accidents or injur ies increases.
- Always take the vehicle key with you
when leaving the vehicle, even for a
short period of time. This applies part ic
ularly when children remain in the veh i
cle. Otherwise the ch ild ren could start
the engine or operate electrical equip
men t such as power w indows.
(D Note
- Avo id h igh engine speed, full throttle,
and heavy eng ine load as long as the en
gine has no t reached operat ing tempera
t u re yet . You could damage the engine.
- T he engine cannot be started by pushi ng
or towing.
(® For the sake of the environment
Do not let the eng ine run w hile pa rked to
warm u p. Begin driv ing immediately . T his
r educes unne cessary emissions.
(D Tips
- If it is d iff icult to turn the key to position
(D , turn the steering wheel back and
forth slightly to release the s teer ing
wheel lock .
- After s tarting a cold engine, there may
be a brief period of inc reased no ise be
cause the oil press ure must first bui ld up
in the hydraulic va lve adj usters . This is
normal and not a cause for concern.
- If the battery is disconnected and recon
nected, you have to hold the ignition key
in posit ion
(D for five seconds for the en
gine to start.
- After sw itching the ignition off, you can
only remove the key when the selector
lever is in the "P" (Park) position. After
that, the selector lever is locked.
•
Page 80 of 302

78 Driving
Stopping the engine with the key
A pplies to vehicles: with mechanical ignit ion lock
Stopp ing the engine
> Bring the vehicle to a ful l stop .
> Turn the key to position @.
Rele asing the steering lock
Requirement : The selector lever must be in
the P pos ition .
> Remove the ignit ion key in position @
Q page 78, fig. 80 Q _&.
> Turn the steering wheel until you hear the
stee ring wheel lock.
The locked steering helps prevent vehicle
theft.
A WARNING
- Never turn off the eng ine before the ve
hicle has come to a complete stop . The
full function of the brake booster and the powe r steering is not guaranteed. You
must use more fo rce to turn or brake, if
necessary. Because you cannot steer and
brake as you usually would, this could
lead to acc idents and se rious injuries.
- Never remove the ign ition key from the
ign ition lock whi le the vehicle is movi ng .
Otherwise, the steering lock co uld sud
denly engage and you would not be able
to steer the vehicle.
- Please note that the brake booster and
power steering only work when the en
gine is runn ing. When the engine off, you
must use more force to steer or brake
the vehicle. Because t he usual steering
and braking capability is not available,
the risk of accidents or injuries increases .
- Always take the vehicle key with you
when leaving the veh icle, even for a
short per iod of time. This applies partic
ularly when chi ldren remain in the vehi
cle. Otherwise the children could start
the engine or operate electrical equip
ment such as power windows .
- For safety reasons, always park the vehi
cle with the selector lever in the P posi- tion. Otherwise, there is the risk t
hat the
veh icle could roll.
- After the engine has been switched off,
the radiator fan can continue to run for
up to 10 minutes -even with the ignition
sw itched off. It can also sw itch on again
after some t ime if the coolant tempera
ture rises as a resu lt of heat buildup or if
the engine compartment is heated by
sunlight and the engine is hot.
(D Note
- If the engine has been under heavy load
for an extended per iod of t i me, heat
builds up in the engine compartment af
ter the engine is switched off - there is a
r isk of damaging the engine . For this
reason, let the engine r un for at id le for
approximately two minutes before shut
ting it off .
Starting and stopping
the engine (vehicles
with a convenience key)
St t· th · ith the
button
Appl ies to vehicles: wit h co nvenience key
The !START E NGIN E STOPI button switches
the ignition on and starts the engine .
Fig. 80 Center conso le: STAR T ENGIN E STOP bu tton
(w ith co nvenie nce key)
You can start your car without using your con
venience key. You must s imply be carrying the
key with you. .,._
Page 81 of 302

M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Switchin g th e ig nition on /off
If the> ,:r- u indicator l ight blinks and the mes
sage
Ple ase move s teering wheel appea rs
when switching the ignition on, the steering is locked by th e steering lock. In this case, turn
the steering wheel slight ly to the left/ right.
.. To switch the ignition on or
off, press the
I S TAR T ENG INE S T OPI button. Do not press
the brake pedal whil e doing this .
Starting the engin e
Your vehicle is equipped with launch cont ro l.
The engine starts automa tically when you
press the
I S T AR T ENG INE S T OP I button brief
l y.
.. Press the brake peda l and move the se lector
lever to the P or N pos ition .
.. Press the
I STAR T ENGINE STOP I button
briefly . The eng ine will star t.
Majo r electrical equ ipment switches
off tem
porarily when starting the eng ine .
I f the engine does not start immediately , stop
the starting procedu re by push ing the
I S TAR T ENGINE ST OP ! button again and re
peat after 30 seconds .
Automatic start m alfunction
If the Ila indicator l ight turns on (gasoline en
g ine) when you start the engine, there is an
automatic sta rt malfunction .
To start the eng ine, press and hold the
!STAR T ENGIN E STOP ! button until the eng ine
runs.
Drive to an authorized Aud i dealer or author
i z ed Audi Service Fac ility immed iately to have
the malfunction corrected .
A WARNING
-Never allow the engine to ru n in confined
spaces -there is a r isk of asphyxiation.
- Always take the veh icle key with you
when leaving the vehicle, even for a
short per iod of t ime . This applies partic
ularly when chi ldren remain in the vehi
cle . Otherwise the children could start
Dri vin g 79
the engine or operate electrical equip
ment such as power w indows.
- Please note that the brake booster and
power steering only work when the en
gine is running. When the engine
off, you
must use more force to steer or brake
the vehicle . Because the usual steer ing
and brak ing capability is not avai lable,
the risk of accidents or injur ies increases .
(D Note
-Avo id h igh engine speed, full throttle,
and heavy eng ine load as long as the en
gine has not reached operat ing tempera
ture yet. You could damage the engine .
- The engine cannot be started by pushing
or towing .
@ For the sake of the environment
Do not let the eng ine run wh ile parked to
warm up . Begin dr iv ing immediately . Th is
reduces unnecessary emissions .
(D Tips
-After starting a cold engine, there may
be a brief period of increased no ise be
cause the oil press ure must f irst bu ild up
in the hydraulic va lve ad justers. This is
normal and not a cause for concern.
- If the . indicator light blinks in the in
st rument cluste r before switching the ig
nition
off, the ignit ion wi ll not switch on
again .
qpoge 192
- If you leave your vehi cle wit h the ignition
switched on, the ign it ion w ill switch
off
after a certain amount of time . Make
sure that electrical equipment such as
the exterior lights are switched
off .
T · th · ff using the
button
App lies to vehicles: wit h convenience key
.. Bring the veh icle to a full stop .
.. Move the se lector lever into the P posit ion .
.. Press the
I STA RT E NGINE ST OP ! button
q page 78, fig. 80. ..,.
•
Page 82 of 302

80 Driving
Steering lock1
)
The steering locks when you turn the engine
off using the
I START ENGINE STOPI* button,
move the selector lever into the P position
and open the driver's door.
The locked steering helps prevent vehicle
theft.
Emergency off function
If it is absolutely necessary, the engine can al
so be turned off while driving at speeds lower
than 6 mph (10 km/h).
If you press the
I START ENGINE STOPI* button while driving,
the message
Pressing start/stop button
again will switch off engine!
appears. To
switch the engine off, press the
I STAR T ENGINE STO PI* button twice in a row
briefly or press and hold for longer than two
seconds.
A WARNING
- Never turn off the engine before the ve
hicle has come to a complete stop. The
full function of the brake booster and the power steering is not guaranteed. You
must use more force to turn or brake, if
necessary. Because you cannot steer and
brake as you usually would, this could
lead to accidents and serious injuries .
- Please note that the brake booster and
power steering only work when the en
gine is running. When the engine off, you
must use more force to steer or brake
the vehicle. Because the usual steering and braking capability is not available,
the risk of accidents or injuries increases.
- Always take the vehicle key with you when leaving the vehicle, even for a
short period of time. This applies partic ularly when children remain in the vehi
cle. Otherwise the children could start
the engine or operate electrical equip
ment such as power windows.
- For safety reasons, always park the vehi
cle with the selector lever in the P posi-
ll This function is not available in all cou ntr ies.
tion. Otherwise, there is the risk that the
vehicle could roll.
- After the engine has been switched off,
the radiator fan can continue to run for
up to 10 minutes - even with the ignition
switched off. It can also switch on again
after some time if the coolant tempera
ture rises as a result of heat buildup or if
the engine compartment is heated by sunlight and the engine is hot.
(D Note
If the engine has been under heavy load
for an extended period of time, heat builds
up in the engine compartment after the
engine is switched off - there is a risk of
damaging the engine. For this reason, let
the engine run for at idle for approximate
ly two minutes before shutting it off.
Starting the engine if there is a
malfunction
Applies to vehicles: with convenience key
It may not be possible to start the engine un
der certain circumstances, for example if the
battery in the vehicle key is drained, if inter
ference is affected the key or if there is a sys
tem malfunction.
Fig. 81 Steer ing colum n/remote control key : start ing
the e ngine
if t h ere is a malfu nction
As long as the message y>l) Key not recog
nized. See owners manual
appears, you can
sta rt your vehicle using the emergency start
function . .,.
Page 83 of 302

M N
" > co ,...., \!) ..,.,
,...., ..,., ,....,
~ Press the brake pedal¢ A in Starting the
engine with the
S TAR T ENGINE STOP but
ton on page 79.
~ Press the l ~ s =T ~A~R=T~E~N-G~I~N~E~s=T~O~P~I button .
~ Hold the maste r key as shown in the illustra
t ion in the location indicated
y>l) ¢ fig . 81 .
The eng ine will start .
~ If the engine does not automatically start,
press the
I STAR T E NGINE STOP! button
again.
Drive to an authorized Aud i dea ler or author
i zed Audi Service Fac ility immed iate ly to have
the ma lfunction co rrected .
(D Tips
You can disp lay the message that appears
during an eme rgency by p ressing the
!S TART EN GINE STOPI* button.
Driver messages
Turn off ig nition befor e leaving car . Batter y
is disc har ging
This message appears and a warn ing tone
sounds if yo u ope n the dr ive r's door when the
i gnit ion is switched on. Sw itch the ignition off
so that the batte ry wi ll not discharge.
Pr ess ing start/stop button again will sw it ch
off engin e!
This message appears when you press the
I STAR T ENGIN E STOP !* button while dr iv ing
¢ page 80, Emergency off function.
E ngine start s ystem malfunction. Please
contact Service
The engine automatic start system has a mal
function. Drive to an authorized Audi dealer or
author iz ed Audi Serv ice Facility immediately
to have the ma lfunction corrected . To start
t he eng ine, press and hold the
I STAR T ENGIN E STOP ! button .
DJ Key not recognized . See owne r's manual
This message appea rs i f the re is no conven
ience key inside the vehicle or if the system
does not recognize the key. The convenience key may not be recognized, for examp le, if it is
Dri vin g 81
cove red by an object that disrupts the s ignal
(such as a briefcase), or if the key battery is
weak. E lectronic devices such as ce ll phones
can a lso interfere with the signa l.
T o still be ab le to start or stop the engine, re
fer to "Correcting a malfunction"¢
page 80.
Ill Key not in vehi cle?
The Ill in dicator light turns on and th is mes
sage appears if the co nvenience key was re
moved from the vehicle when the engi ne was
run ning . If the convenience key is no longer in
the ve hicl e, you cannot switch the igni tion on
o r start the engine once yo u stop it . You also
cannot lock the vehicle from the outside .
Press brake pedal
Th is message appears if you do not p ress the
brake pedal when sta rting the eng ine .
Please eng age N or P
This message appears when starting or stop
ping the engine if the se lector l ever is not in
the N or P position. The engine will not start/
stop.
Shift to P , othe rwi se vehicle can roll away.
Door s do not lock if le ver is not in P
T h is mess age appears for safety reasons
along wi th a warn ing tone.
It appea rs if the
selector lever for the automatic transm ission
is not in the P pos it ion when switching the ig
nition off with the
I S TAR T ENGINE STOP !*
button. Shift the se lec tor lever to the P posi
tion . Otherw ise, the vehicle could roll . You al
so cannot lock the vehicle us ing the loc king
senso r o n the door hand le or using the con
venience key.
•
Page 84 of 302

82 Driving
Electromechanical
parking brake
Operating
The electromechanical parking brake replaces
the hand brake.
Fig. 82 Ce nter conso le: Park ing brake
~ Pull the switch@~ fig. 82 to set the park
ing brake . The . (USA models)/ . (Cana
da models) indicator lights in the button
and in the instrument cluster display turn
on .
~ To release the parking brake, press the brake
or acce le rator pedal while the ignit ion is
switched on and press the button @at the
same time. The. (USA models)
I. (Can
ada models) indicator lights in the button
and in the display turn off .
Your veh icle is eq uipped with an electrome
chanical parking brake. The parking brake is
designed to prevent the vehicle from rolling unintentionally and replaces the hand brake.
I n addition to the normal functions of a tradi
tional hand brake, the electromechanical parking brake provides various convenience
and safety functions.
When starting from a stop
- T he integral hill start assist helps you when
dr iving by automatically releasing the park
ing brake ~
page 83, Starting from a
stop .
-When starting on inclines, the hill start as
sist prevents the vehicle from unintentional
l y rolling back. The braking force of the
parking brake is not released until sufficient driving force has been built up at the
wheels.
Emergency brake function
An emergency braking functions ensu res that
the vehicle can be slowed down even if the
normal brakes fail~ page 84, Emergency
braking function.
_.&. WARNING
- Do not press the accelerator pedal inad
vertently when the vehicle is stationary
and the engine is running and a gear is
selected. Otherwise the vehicle will start
to move immediately and could result in
a crash .
- If the power supply fails, the released
parking brake can no longer engage . In
this case, park the vehicle on leve l
g round and secure it by placing these
lecto r lever in the P position. See an au
thorized Audi dealer or authorized Audi
Service Facility for assistance.
(D Note
If the. or. (USA models) I. (Cana
da models) indicator light in the instru
ment cluster blinks, there is a malfunction
i n the brake system. Refer to the detai led
description of the indicator lights
~page 18.
- If the . (USA models) I. (Cana-
da models) or
Ill indicator light turns
on, there is a malfunction in the parking
brake
c> page 19.
(D Tips
- If the electromechanica l parking brake is
set while the ignition is switched off, the
¢@'A indicator light in the button and in
the instrument cluster dis-
play . (USA models) /. (Cana-
da models) will turn off after a certain
amount of time.
- If driver's door is opened while the igni
tion is switched on, the park ing brake
sets automatically. This prevents unin
tended rolling of the vehicle.
Page 88 of 302

86 Driving
• To store the speed, p ress the button @. T he
II (USA models) I i'I (Canada models)
turns on in the instrument cluster.
Changing speed
Applies to vehicles: with cru ise control system
• To increase or decrease the speed in incre
ments,
t ap the lever in the 010 direction
c:> page 85, fig. 83.
• To increase or decrease the speed qu ickly,
h o ld the leve r in the 010 direction until
the des ired speed is reached .
Overriding the speed
You can press the acce lerator pedal down to
increase your speed, for example if you want
to pass someone . The speed you saved earlier
will resume as soon as you release the acceler
ator pedal.
I f, however, you exceed your saved speed by 5
mph (10 km/h) for longer than 6 minutes, the
cruise contro l turns off temporari ly. The
Ill
(USA models) I El (Canada models) indicator
light in the instrument cluster turns off and
the stored speed is retained.
Preselecting the speed
Applies to vehicles: with cruise control system
You can preselect your desired speed when
the vehicle is stationary.
• Switch the ignition on.
• Pull the lever into position
(D c:> page 85,
fig. 83.
• To increase or decrease the speed, tap the
lever in the
0 10 d irect io n.
This funct ion makes it possible, for example,
to save the speed you want before driving on
the highway . Once on the highway, activate
the cruise contro l by pull ing the lever towa rd
(D .
Switching off
Applies to vehicles: with cruise control system
Temporary deactivat ion
• Press the brake pedal, or
• Press the leve r into position @(not clicked
into p lace)
~ page 85, fig. 83, or
Switching off completely
• Press the lever into position @(clicked into
place), or
• Switch the ignit ion off.
The speed you stored will be retained if the
c ruise control has been switched off tempora
rily . To resume the stored speed, re lease the
brake pedal and pu ll the lever into position
(D.
The stored speed is erased when the cruise
control is sw itched off complete ly or the igni
t ion is switched off .
,&. WARNING
You should only resume the stored speed if
i t is not too high for ex isting traffic con di
tions . Othe rwise you r is k an acc ident.
(D Tips
- If the bra kes become too heated whi le
dr iving, t he cr uise control sw itches off. If
t his happens w hile d riving downhill, you
can relieve t he b rakes by shifting into a
lower gear.
- W hen the cruise cont rol is activa ted, E SC
sport mode cannot be switched on .
Page 94 of 302

92 Audi adaptive cruise control
• press the brake peda l.
• To resume the stored speed, move the lever
i nto position @.
Interrupting cruise control when stopped
• Push the lever away from you into position
@. The message ACC : standby appears .
• To resume cru ise control, press the brake
pedal and pull the lever toward you into po
sition @.
A WARNING
It is dangerous to activate cruise control
and resume the stored speed when the
current road, traffic or weather conditions
do not permit th is . Th is could result in a
crash .
Setting the distance
Applies to vehicles: wit h Audi adapt ive cru ise co ntrol
Fig. 92 Operat ing lever : Sett ing t he dist ance
-
• Tap the swit ch to display the current set dis
t ance
¢f ig. 92.
• To increase or reduce the distance in incre
ments, tap the switch again to the right or
left . The distance between the two vehicles
will change in the instrument cluster dis
play.
When approaching an object detected ahead,
the adaptive cruise con trol system brakes to
match that object's speed and then reg ulates
to the stored distance . If the object detected
ahead acce lerates, adapt ive cruise control will
a lso acce lerate up to the stored speed .
The highe r the speed, the greater the distance
in meters
c::;, & . The Distance 3 setting is rec
ommended. That is equal to the general rec- ommendation of "hal
f the speed shown on
the speedometer".
T he distances provided are example values.
Depending on the driv ing s ituation, the cur
rent speed and the way the object detected
ahead is driving, the actual distance may be
more or less than these target distances.
o:::::::, _o:::::::, ___ Distance 1: This setting cor re-
sponds to a distance of 92 feet
I 28 meters
when traveling at 62 mph (100 km/h), or a
t ime distance of 1 second.
o:::::::, __ o:::::::, __ Distance 2: This setting corre
sponds to a distance o f 118 feet/ 36 meters
when traveling at 62 mph (100 km/h), or a
t ime distance of 1.3 seconds .
o:::::::, ___ o:::::::,_ Distan ce 3: Thi s sett ing corre-
sponds to a distance of 164 feet/ 50 meters
when traveling at 62 mph (100 km/h), or a
t ime distance of 1.8 seconds.
o:::::::, ____ o:::::::, Distance 4: Thi s sett ing corre-
sponds to a distance of 219 feet/ 67 meters
when traveling at 62 mph (100 km/h), or a
t ime distance of 2.4 seconds.
A WARNING
--
- Driving too close to other vehicles in
creases the risk of collisions and ser ious
in jur ies.
- Sett ing short distances to vehicles ahead
reduces the distance and time that you
have to stop your vehicle safe ly . This in
creases the need for you to pay attention
to traffic.
- Always follow applicable traff ic laws , use
common sense and select a distance to
veh icles ahead that takes the current
traffic , road and weather conditions into
account.
{i) Tips
Distance 3
is set automatically each time
you switch the ignition on.
It you would
lik e to have this distance as a basic setting,
you can have the
adaptive cruise control
menu extended/ enabled from an author
ized repair facility .