light AUDI A3 SEDAN 2018 Service Manual

-Always hold the steering whee l with your
hands in the 9 o'clock and 3 o'clock posi­
tions to reduce the risk of injury if the airbag
deploys.
- Never hold the steer ing wheel in the 12
o'clock position or with both hands on the
rim or the center of the steer ing wheel.
Holding the steering wheel incorrectly s ig­
nificantly increases the risk of in jury to the
hands, arms and head if t he a irbag dep loys.
Starting and stopping
the engine (vehicles with an ignition lock)
Starting the engine
A pp lies to: ve hicles with ignitio n lock
The ignition is switched on and the engine start­
ed with the key in the ignition .
Fig. 84 Ignit io n lock: posit io n of the ignit io n key
Switching the ignition on /off
• To switch the ign ition on, turn the ign ition key
to posit io n
CI) . Vehicles without the Start/Stop
system*: the needle in the tachometer moves
into the
READY position.
• To switch the ign ition off, turn the ignit io n key
to posit ion @. The needle in the tachometer
moves into the
OFF position .
Starting the engine
• Press the brake pedal and move the se lector
lever to the "P" or "N" position.
• Turn the key briefly to position @. The ignition
~ key automatically returns to position CI) . Do not
~ press the acce lerato r pedal when doing this .
N ..... 0 N > co
Drivi ng
Equipment that uses a lot of e lectricity is switch­
ed off temporarily when you start the engine .
If the engi ne does not start immediately , stop
the starting p rocedure by turning the ign it ion key
to posit ion @ and repeat after 30 seconds .
Start/Stop system*
See the information in Q page 79 , Start/Stop
system.
_&. WARNING
- T o redu ce the r is k of po iso ning, never allow
t he engi ne to run in confined sp aces.
- Never remove the ignition key from the ig ni­
t ion lock while the vehicle is moving. Other ­
wise the steer ing lock will engage and yo u
will not be ab le to steer the vehicle, which
increased the risk of an acc ident.
(D Note
Avo id high engine s peed, fu ll th rottle, and
heavy engine load i f th e e ngine has not
reached operating temperat ure yet . You could
damage the eng ine .
@ For the sake of the environment
Do not let the engine run w hile parked to
warm up. Beg in driving immediate ly . Th is re­
d uces unnecessary emissions.
@ Tips
- If it is d ifficult to turn the key to pos ition
CI) , turn the steering wheel back and forth
slightly to release t he steering whee l lock .
- S ome noise after start ing the e ngine is no r­
ma l and is no cause for co ncern.
Stopping the engine
Applies to: vehicles wi th ignition lock
Stopping the engine
• Bring the vehicle to a full stop .
• Turn the key to position @. The needle in the
tachometer moves into the
OFF pos ition.
Engaging the steering lock
Requireme nt: the se lector lever must be in P .
75

Driving
,.. Remove the ignition key in position @
9 page 76, fig. 85 9 ,&..
,.. Turn the steering wheel until you hear the
steering wheel lock.
The locked steering helps prevent vehicle theft.
A WARNING
- Never turn off the engine before the vehicle
has come to a complete stop. The full func­
tion of the brake booster and the power
steering is not guaranteed. You must use more force to turn or brake . Because you
cannot steer and brake as you usually
would, this co uld lead to accidents and seri-
. . . ous mJunes .
-Never remove the ignit ion key from the ign i­
t ion loc k while the vehicle is moving. Other­
wise, the steering lock could suddenly en­
gage and you would not be able to steer the
vehicle.
- If you leave the veh icle, switch the ignit ion
off and take the vehicle key with you. Other­
wise, the engine could be started or electri­
cal equipment such as the power windows
could be operated. This can lead to serious
injury.
- For safety reasons, always park the vehicle
with the selector lever in the P position.
Otherwise, there is the risk that the vehicle
could roll unintentionally .
(D Note
If the engine has been under heavy load for
an extended period of t ime, heat builds up in
the engine compartment after the engine is
switched off and there is a risk of damaging
the engine . For this reason, let the engine run
for at idle
for approximately two minutes be­
fore shutting it
off.
@ Tips
For up to 10 minutes after stopping the en­
gine, the radiator fan may turn on again auto­
matically or it may continue to run (even if
the ignition is sw itched
off) for the following
reasons:
76
- The coolant temperature is increasing due
to trapped heat.
- If the engine is warm and the engine com­
partment also heats up from strong sun­
light.
Starting and stopping
the engine (vehicles with
convenience key)
Starting the engine
App lies to : vehicles wit h co nvenience key
The I START ENGINE STOP I button switches the
ignition on and starts the engine.
Fig. 85 Center conso le: STAR T ENGINE ST OP button
Plug-in hybrid drive*: refer to the information for
start ing the veh icle under
9 page 94.
Starting the engine
.,. Press the brake pedal and move the selector
lever to the "P" or "N" position .
.,. Press the I START ENGIN E STOP I button briefly .
The engine will start.
Equipment that uses a lot of electricity is switch­
ed
off temporarily when you start the engine .
If the engine does not start immediately, stop
the starting procedure by pushing the
I START ENGINE STOP! button again and repeat
after 30 seconds .
Switching the ignition on/off
If you would like to switch the ignition on with­
out starting the engine, follow these steps:
.,. Press the I ST AR T ENGINE ST OP ! button with-
out
pressing the brake pedal. Vehicles without .,,.

u. 00 .-< N l'­ N .-< 0 N > 00
the Start/Stop system*: the needle in the
tachometer moves into the
READY position .
~ To switch the ign ition off, press the button
again. The needle in the tachome ter moves into
the
OFF posit ion.
If the
,:rM i ndicator light b links and the message
Please turn steering wheel appears when switch­
ing the ign ition on, the steer ing lock has been en­
g aged . In this case, turn the steering wheel
slig htly to the left or right .
Start/St op sy stem*
See the information in <=!) page 79, Start/Stop
system.
A WARNING
To red uce the risk of poisoning, never allow
the engine to run in confined spaces.
@ Note
Avoid hig h engine speed, full throttle, and
heavy engine load if the engine has not reached operating temperature yet. You could
damage the engine.
@) For the sake of the environment
Do not let the engine run whi le parked to
warm up. Begin driving immediately . This re­
duces unnecessary emissions.
(D Tips
- Some noise after starting the engine is nor­
mal and is no cause for concern.
- If you leave your ve hicle with the ignition
switched on, the ignition will switch off af­
ter a certa in amount of t ime. Make sure that
electr ical equ ipment s uch as the exter ior
li ghts are sw itched off.
Stopping the engine
Applies to: vehicles with convenience key
-
Plug-in hybrid dr ive*: refer to the informat ion un­
de r
<=!) page 94.
~ Bring the vehicle to a ful l stop .
ll This fun ctio n is not a vail abl e in a ll co untries.
Driving
~ Move the selector lever into t he P posit ion .
~ Press the !S T AR T ENGINE ST OP ! button
<=!)page 76, fig . 85 .
Steering lock1>
The steer ing locks when yo u tur n the eng ine off
u sing the
!S TAR T ENG INE S TOPI* button, move
the se lector lever into the P position and open
the driver's door. The locked steering helps pre ­
vent vehicle theft .
Emergency off function
If it i s absolutely necessa ry , the eng ine c an also
be turned off wh ile d riving at speeds starting at
4 mph (7 km/h) . To switch the engine off, press
the
I S T AR T ENGINE STOPI button twice in a row
briefly or press and ho ld for longer than two sec­
onds.
A WARNING
--
- Never turn off the eng ine before the vehicle
has come to a complete stop . The full func ­
tion of the brake booste r and the power
steer ing is not guaranteed. You must use
mo re fo rce to t urn o r bra ke. Be ca u se you
can not stee r and br ake as yo u usually
wo uld, this could lead to acc idents and seri ­
ous injuries .
- I f you leave the vehicle, sw itch the ignition
off and take the ve hicle key wi th yo u. Other ­
wise, the engine could be started or e lectri ­
cal equipment such as the power windows
could be operated . This can lead to serious
injury .
- For safety reasons, always park the vehicle wit h the selector lever in the P pos ition.
Otherw ise, there is the risk that the vehicle
could roll unintentiona lly .
@ Note
If the engine has been under heavy load for
an extended period of time, heat builds up in
the eng ine compartment after the engine is
switched off and there is a r isk of damag ing
the e ng ine . Fo r thi s reason, let the e ng ine run
.,.
77

Drivin g
for at idle fo r approximately two minutes
before shutting it off.
(D Tips
For up to 10 m inutes after stopp ing the en­
gine, the rad iator fan may t urn on again auto­
matically or it may continue to run (even if
the ignition is sw itched off) for the following
reasons:
- The coolant temperature is increasing due
to trapped heat.
- If the engine is warm and the engine com­
partment also heats up from strong sun­
li ght.
Messages
Engine runn ing. W arning! Turn off ignition be ·
fore le aving vehicl e
This m essage appears and a warning tone sounds
if you open the driver 's door when the engine is
running .
Press ing start /stop button again will swi tch off
engine.
This message appea rs when you press the
IS TAR T ENG IN E STOP I* button wh ile d riving
¢ page 77, Emergency off function.
Engine start system: malfunction! Ple ase con­
tact S ervice
The engine automatic start system has a mal­
function . Drive to an author ized Audi dealer or
author ized Audi Se rvice Facility immed iate ly to
have the ma lfunct ion co rrected. To sta rt the en­
g ine , turn the key to pos it io n @ ¢
page 75 or
p ress and ho ld the
I S TART ENGINE ST OP ! button
until the engine is running .
DJ Key not r ecogniz ed . See own er' s manual
This message appears if there is no convenience
key inside the vehicle or if the system does not
recognize the key . T he conven ience key may not
be recognized, for examp le, if it is cove red by an
object that
disrupts the s ignal (s uch as a b rief ­
case), o r if the key ba tte ry is weak. Elect ronic de ­
vices s uch as cell phones can also interfere wit h
the signal.
78
To still be ab le to start or stop the engine, re fer
to
¢ page 79.
DJ Re mo te c ontro l ke y: hold back of ke y
again st the de signated ar ea . S ee owner 's man­
ual
If the indicato r light turns on and this message
appea rs, there is a ma lfunction ¢
page 79.
Ill Key not in v ehicle?
Ill Remote control ke y: key not r ecogni zed. Is
t he key still in the vehicle ?
The Ill indicator light turns on and this message
app ears if the conv eni ence k ey was r emoved from
the veh icle when the engine was running.
If the
convenience key is no longer in the ve hicle, you
cannot sw itch the ignition on or start the eng ine
once you stop it . You also cannot lock the vehicle
from the outside .
Please press the bra ke pedal
This message appears if you do not step on the
brake peda l to start the engine on a vehicle with
an automat ic transmission.
Plea se select N or P
This message appears w hen start ing or stopping
t h e engine if t he se lecto r lever is not in t he "N " or
"P " pos ition. The eng ine will not sta rt/stop.
Turn off igniti on befor e le av ing vehicle . Batter y
i s di sc harging
This message appears and a warning tone sounds
i f you open the driver's door w hen the ign it ion is
switched on . Sw itch the ignit ion off so that the
vehicle battery will not discharge.
S hift to P , othe rwi se vehicle can roll aw ay.
Door s do not lo ck if l ever is not in P
This message appears for safety reasons if the
selector lever for the automa tic transmission is
not in the P position after the ignition is switched
off . Move the selector lever to the P posit ion .
Otherwise the ve hicle is not protected from roll­
i ng and it cannot be locked .

LL co .... N
" N .... 0 N > co
Starting the engine
when there is a
malfunction
Applies to: vehicles with conven ience key
It may not be possible to start the engine under
certain circumstances, for example, if the bat ­
tery in the vehicle key is drained, if interference is
affecting the key or if there is o system mo/func­
tion.
Fig. 86 Steering col umn/remote co ntro l key: starting the
eng ine if there is
a malfunction
As long as the message II Key not recognized.
See owner's manual or
II Remote control key:
hold back of key against the designated area.
See owner's manual
appears, you can start the
vehicle with the emergency starting function .
.. Press the brake pedal.
.. Hold the master key in the location indicated in
the illustration
y>l) c> fig. 86.
.. Press the I START ENGINE STOPI button c> .& in
Starting the engine on page
77 . The engine will
start.
.,. Drive to an authorized Audi dealer or author­
ized Audi Service Facility immediately to have
the malfunction corrected.
@ Tips
You can display the message that appears
during an emergency by pressing the
!START ENGINE STOPI button.
l) Market -spe cific
Driving
Start/Stop system
Description
Applies to: vehicles wit h Start/Stop system
The Start/Stop system can help increase fuel
economy and reduce CO2 emissions.
In Start/Stop mode, the engine shuts off auto ­
matically when the vehicle is stopped, such as at
a traffic light. The ignition remains switched on
during this stop phase. The engine w ill restart
automat ically when needed.
The Start/Stop system is automatically activated
as soon as the ignition is switched on.
Basic requirements for Start/Stop mode
-The driver's door must be closed .
- The driver's seat belt much be fastened.
- The hood must be closed.
- The vehicle must have driven faster than
2 mph
(3 km/h) since the last time it stopped.
(D Note
Always switch the Start/Stop system off when
driving through water
c> page 81.
(D Tips
The engine stops shortly before the vehicle
comes to a stop
ll. The full function of the
brake booster and the power steering is still
available.
Stopping/starting the engine
Applies to: vehicles with Start/Stop system
Fig. 87 Instrument cluster: eng ine switched off (stop
phase)
79

Drivin g
~ Brake the vehicle to a stop . The engine stops
shortly before the vehicle comes to a stop or if
the ve hicle is stationary
1>. Keep your foot on
the brake pedal. The
D] ; D] ind icator light ap ­
pears in the display. The need le in the tachome­
ter also moves into the
READ Y position .
~ The engine starts again when you take your
foot off the brake pedal. The ind icator light
tu rns off.
Add ition al informa tion
The engine stops in the "P", "N" and "D" selector
lever positions .
If you select the "R" selector lever position during
a Stop phase, the engine will start again.
Shift to "P" quickly to prevent the engine from
starting unintentiona lly when shifting t hrough
IIRII.
You can determ ine for you rself if the engine will
stop or not by reducing or increasing the amount
of force you use to press the brake pedal. For ex­
ample, if you only light ly press on the brake ped­
al in stop-and-go traff ic or when turning, the en­
g ine will not switch off when the vehicle is sta­
tionary . As soon as you press the brake down
harder, the eng ine will switch off .
(D Tips
-Press the brake pedal during a Stop phase
to keep the veh icle from roll ing.
- The ignition will turn off if you press the
I STAR T ENGINE ST OP ! button* during a
stop phase . The needle in the tachometer
moves into the
OFF pos it ion .
General information
App lies to: ve hicles w ith Sta rt/Stop system
Engine does not switch off
Before and during each stop phase, the system
checks if certa in cond itions have been met. If the
fjj i ndicato r light appears in the instr ument clus­
t er d isp lay, the engine w ill no t be s topped, for
examp le in the fo llowing situations:
1) Ma rket -spe cific
80
- T he engine has not reached the minim um re­
quired temperature for Start/Stop mode.
- The interior temperature selected by the cli-
mate control system* has not been reached.
- The ou tside tempe rat ure is extremely high/low.
- The windsh ield is being
defrosted® .
-The parking system* is switched on .
- The vehicle battery charge level is too low .
- The steering wheel is turned at a sharp angle or
is moving.
- After engaging the reverse gear.
- On sharp inclines .
- At high altitudes .
Engine automaticall y restarts
The standard Start/Stop mode w ill be canceled
d u ring a stop p hase in the following situat ions.
The eng ine res tarts witho ut any act ion by the
drive r.
- The vehicle ro lls, for example while on a slope .
- The interior temperature differs from the tem -
peratu re selected in the A/C system .
- The windsh ield is being
defrosted® .
-The brake pedal is pressed several times in a
row.
- The vehicle battery charge level is too low.
- Power consumption is hig h.
The eng ine ca n tur n off aga in when the cond i­
t ions for Sta rt/S top mode a re met
l ).
Ignition is switched off automaticall y
To prevent the vehicle battery from dra ining, the
i gnition will sw itch off
a ut omaticall y under the
fo llow ing cond it ions:
- The Start/Stop system has stopped the engine .
- The vehicle is stationary.
- You exited the vehicle .
In this case, the activated low beam is rep laced
by the pa rking light . The parking lights wi ll
switch off after approximately 30 minutes or
when you lock the veh icle.
.,.

LL co .... N
" N .... 0 N > co
If the Start/Stop system has not turned off the
engine or if you have switched the Start/Stop sys­
tem off manually, the ignition will not be auto­ mat ically switched off and the engine w ill contin­
ue to run
c:> ,1. .
A WARNING
To reduce the risk of poisoning, never allow
the engine to run in confined spaces.
(D Tips
If you select the "D" or "N" selector lever pos i­
tion in a veh icle with an automatic transmis­
sion after shifting into reverse, the vehicle
must be dr iven faster than 6 mph (10 km/h)
in order for the engine to sw itch off again.
Manually switching the Start /Stop system
on /off
Appl ies to: ve hicles with Sta rt/Stop system
If you do not wish to use the system, you can
switch it off manually.
F ig. 88 Center co nsole: Start/Stop system button
-
.. To switch the Start/Stop system off/on man­
ually, press the
l(A) ~I button. The LED in the but­
ton turns on when the system is sw itched off .
(D Tips
If
you switch the system off during a stop
phase, the engine will start again automati­
cally.
Messages in the instrument cluster display
App lies to: ve hicles with Start/Stop system
ma Sta rt /s top sy ste m: dea ctivated. Plea se sta rt
e ngine manually D
rivi ng
This message appears when spec ific conditions
are not met du ring a stop phase . The Start/Stop
system will
not be ab le to restart the engine. The
engine must be started manua lly.
ma Sta rt/stop sy stem : ma lfunction! Function
una vailable
T he re is a m alfu nction in the Start/Stop system.
Drive the vehicle to an authorized Aud i dea ler or
authorized Service Facility as soon as possible to
have the malfunction corrected.
Electromechanical
parking brake
F ig . 8 9 Cen ter console : park ing brake
ra 0 > (IO m
Your vehicle is equipped with an electromechani ­
ca l parking brake
(D c:> fig. 89 . The parking brake
is des igned to prevent the veh icle from rolling
unintentionally and replaces the hand brake.
Sett ing /manuall y releasing the parking
brake
.. Pull the(®) switch to set the parking brake. The
LED in the switch turns on. The
-(USA mod­
els)/ . (Canada models) ind icator light also
turns on in the instrument cluster disp lay .
.. To release the park ing brake man ually, press
the bra ke or accelerator peda l wh ile the ign i­
tion is sw itched on and press the
(®) switc h at
the same time. The LED i n the bu tton and the
ind icator light in the d isplay turn off.
Releas ing the parking brake automatically
Requireme nt: the driver's door must be closed
and the parking brake must be se t.
81

Driving
- If the vehicle sti ll does not move in the de ­
sired direction, there is a system malfunc­
tion. See an authorized Audi dealer or au­
thori zed Audi Service Facility for assistance
to have the system checked.
(D Tips
Plug -in hybrid drive* : the transmission
switches automatically to the normal mode
" D" if the
l.,,f' I button ¢ page 98 is pressed
while i n sport mode "S" .
Driving tips
Applies to: ve hicles with a utomat ic transmissions
F ig . 9 2 Sect io n of the cente r co nso le: se le cto r lever w it h
i nte rlock butto n
Starting the engine
• Select the "P" or "N" selector lever position . At
low temperatu res (be low 14 °F ( -10 °C)), the
engine can only be started when t he se lec to r
l ever is in the "P " posit io n.
Starting from a stop
• Press and hold the brake pedal.
• Press and hold the interlock button in these­
lector lever handle, se lect the des ired sele ctor
lever posit io n such as "D" ¢
page 84 and re­
lease the loc k bu tton.
• Wait a moment unti l the transmission shifts.
Yo u w ill not ice a slight movement when the
gear engages.
• Release the brake pedal and press the accelera­
tor
pedal ¢,&. .
Various convenience functions are avai lab le for
starting on hills ¢
page 83.
86
Stopping temporarily
• Keep the vehicle st ationary using the bra kin g
peda l, for examp le a t traffic ligh ts.
• Do not press the acce le rato r pedal when doing
this.
• To prevent the vehicle from rolling when you start driving, set the pa rking brake when stop­
ping on steep
hills ¢.&. and ¢(Q).
• The parking brake will release a utomat ica lly
and the vehicle will start moving once yo u press
the acce le rato r pedal. Requirement: the d riv­
er's doo r mus t be closed.
Stopping/parking
If the selector lever is not in the "P" pos ition
whe n you open the d river's door, the vehicle
could roll. In vehicles with a conven ience key *,
the message :
Shift to P, otherwise vehicle can
roll away. Door s do not lock if lever is not in P
appe ars . A wa rning tone wi ll also sound.
• Press and hold the brake peda l¢ ,&. .
• Set t he par king brake.
• Select the "P" se lector lever posi tion .
Un der certai n circumstances, (such as dr iving in
the mo unta ins or towi ng a trailer), it may be use­
ful to switch temporar ily to the m an ual shift pro­
gr am in or der to ad ju st t he gears to the driv ing
cond it ions by hand ¢
page 88.
When parking on a level surface, s imp ly place the
se le ct or lever i n the "P" pos ition. On inclines, a c­
tivate the par king b rake first and then move the
se lector lever to the "P " posit ion ¢
page 81. Thi s
prevents the locking mechanism from being
l oaded too heavily and will make it easier to
move the selector lever out of the "P" position.
A WARNING
- The vehicle can roll even whe n the engi ne is
sw itched off .
- Unintended vehicle movement can lead to
serio us injuries.
- Never leave your veh icle with the engine
r u nning while in gear. If you must leave
your veh icle when the eng ine is r unning, set
t he par king brake and move the se lecto r lev ­
er to the "P " posi tion .

u. 00 .-< N l'­ N .-< 0 N > 00
-Power is still transferred to the wheels
when the engine is running at idle. To pre­
vent the vehicle from "creeping", you must keep your foot on the brake when the en­
gine is running and the selector lever is in
the "D", "S" or "R" position or "tiptronic"
mode is selected.
- Do not inadvertently press the accelerator
peda l when the vehicle is stopped if a gear is
engaged. Otherwise the risk of an accident
increases because the vehicle will start to
move immediately, even if the parking brake
is set.
- To reduce the risk of an accident, do not
press the acce lerator pedal when changing
the selector lever position while the vehicle is stationary and the engine is running.
- Never engage the "R" or "P" selector leve l
positions while driving. It could cause a
crash.
- Before driving down a steep slope, reduce
your speed and shift into a lower gear with
"ti ptron i c".
- Do not ride the brakes or press the brake
pedal too often or too long when driving
downhill. Constant braking causes the
brakes to overheat and substantially re­
duces braking performance, increases brak­
ing distance or causes complete failure of
the brake system.
- If you must stop on an incline, always hold
the vehicle in p lace with the foot brake or
park ing brake to prevent it from rolling
back.
- Never hold the veh icle on an incline with a
sl ip ping clutch. The clutch opens automati­
cally when it becomes too hot from the
overload. The
ml indicator light turns on
and a message appears
¢ page 89 when
the clutch is over loaded .
{LlJ) Note
- When stopping on an incline, do not try to
ho ld the vehicle in place by pressing the ac­
ce lerator pedal while a driving gear is se ­
l ected. This can cause the automatic trans ­
mission to overheat and can damage it. Set
Driving
the parking brake or press the brake pedal
to prevent the vehicle from rolling.
- Allowing the vehicle to roll when the engine
is stopped while the selector lever is in the
"N" position will damage the automatic
transmission, because it is not lubricated
under those circumstances
¢ page 3 78,
Towing with a tow truck.
- The transmission can overheat and be dam­
aged under certain driving and traffic condi­
tions such as frequent starts, creeping for a
long time, or stop-and-go traffic. When the
ml or. indicator light turns on, stop the
vehicle at the next opportunity and let the
transmission cool¢
page 89.
(D Tips
For safety reasons, the park ing brake only re­
l eases automatically when the driver's door is
closed.
Hill descent control
App lies to : vehicles wi th automatic transmiss ions
The hill descent control system assists the driver
when driving down hills.
Hill descent control is act ivated when the selec­
tor lever is in the "D" or "S" posit ion and you
press the b rake pedal. The transmission auto ­
matically se lects a gear that is suitab le for the
hill. Hill descent contro l tries to ma inta in the
speed achieved at the time of braking, within
physical and technica l limitations. If may still be
necessary to adjust the speed with the brakes.
Because hill descent control cannot shift down
farther than 3rd gear, it may be necessary to
shift into tiptronic mode in very steep areas . In
th is case, shift into 2nd or 1st gear in t iptronic
mode to use the engine's braking force to rel ieve
the brakes.
Hill descent control switches
off once the hill lev­
els out or you press the accelerator pedal.
On vehicles with a cruise control system*
¢ page 120, hill descent control is also activated
when the speed is set .
.,,.
87

u. co ... N l'­ N
A WARNING
Please note that the wheels could spin on
slick or slippery roads when kick-down is ac­
tive .
Launch control program
App lies to: ve hicles with S tro nic tra nsm issio n an d La unch
Co ntrol P rogram
-
The launch control program provides the best
possible acceleration when starting from a stop .
Requirement: the eng ine must be at operating
temperature and t he steer ing whee l must not be
turned.
.,. Deact ivate l) the S tart/Stop system*
~ page 81. The L ED in the ~ button turns on .
.,. Wi th the engine runn ing, p ress the I.!, O FF ! but­
ton briefly one time . The
11 indicator light
turns on and the message
Stabili zation control
( ESC ): s port. W arning! Rest ricted st a bilit y
ap­
pears in the instrument cluster display.
.,. Pull the selector lever back out of the "D/S" po­
s it ion br iefly to select the S pos it ion, or press it
toward the right into the t iptronic pos ition or
select the
Dynamic d riving mode in d rive se­
lect* ~ page 140.
.,. Press t he b rake peda l firmly with you r left foot
and hold it all the way down for at least one
second .
.,. At the same time, press the gas pedal a ll the
way down with your right foot unt il the engine
reaches and stays at a high RPM level.
.,. Remove your left foot from the brake pedal
within five
seconds ~,&. .
A WARNING
-Always adapt yo ur driv ing to the traffic flow.
- Only use Launch Control when road and traf-
fic cond itions allow it and other dr ivers will
not be endangered or impacted by you r driv­
ing and the vehicle 's accele ration.
- Please note tha t the drive whee ls can sp in
and the vehicle can break away when sport
8 l ) It is n ot poss ib le to deac tiv ate t he system wit h all ve rs io n s N &j of th e tran sm iss ion.
Driving
mode is switched on, especially when the
road is slippery.
- Once the vehicle has started moving, press
the !.!> OFF I button briefly to turn the sport
mode off.
(D Tips
- The transmission temperat ure may increase
significant ly after using the launch control
program. If that happens, the program may
not be ava ilable for a few minutes. It will be
availab le aga in after a cool-down period.
- When accelerating using the launch contro l
program, all vehicle parts are subject to
heavy loads . This can lead to increased
wear .
Transmission malfunction
Applies to: vehicles wit h automatic transmissions
• Transmis sion : malfunction! Pl eas e s top ve ­
hicle and shift to P
There is a malfunction in the transmission . Park
the vehicle securely and do not cont inue driv ing .
See an author ized Audi dealer or author ized Audi
Se rvice Facility for assistance .
• Transmission o verhe ating! Plea se stop th e
vehicle!
The transmission is too hot and can become dam­
aged. Stop and let the transmiss ion cool w ith the
engine running (at idle) i n the "P" selector lever
pos ition . T hen the ind icator light and the mes­
sage turn off, d rive to an authorized Aud i dealer
o r auth o rized Aud i Serv ice Facility immediately to
have t he malfunct ion cor rected . If the indicato r
light and the driver message do not turn off, do
not continue driving . See an authorized Audi
dealer or authorized Audi Service Facility for as­
s istance.
[O] Tran smission: malfunction! You can contin-
u e dri ving. See owne r's manual
.,.
89