AUDI A7 2017 Owner´s Manual

co
co
.... N
" N .... 0
00
<.,;) 'SI"
In stop-and-go traffic, adaptive cruise control can
brake until the vehicle is stationary and then be­
gin driving again under certain conditions
¢page 92.
Audi braking guard can warn you about an im­
pending collision and initiate braking maneuvers
¢page 94.
Which functions can be controlled?
When you switch adaptive cruise control on, you
can set the current speed as the "control speed"
¢ page 91, Switching on/off.
When driving, you can stop cruise control
¢
page 92 or change the speed ¢ page 92 at
anytime.
You can also set the distance to the object mov­
ing ahead and set the driving mode of the adap­
tive cruise control¢
page 93 .
General information
Applies to: veh icles with Audi adaptive cruise control
Fig. 91 Front of t he vehicle: sen sors and video came ra
The areas that contain the radar and ultrasonic
sensors and the video camera¢
fig. 91 must not
be covered by stickers, deposits or other objects
because they can interfe re with the function of
the adaptive cruise control system and braking
guard. For information on cleaning, refer to
¢
page 235. The same applies for any modifica­
tions made in the front area.
The function of the adaptive cruise control sys­
tem and brak ing guard is limited under some
conditions.
- Objects can only be detected when they are
within the sensor range¢
page 88 , fig. 90 .
Assist
- The system has a limited ability to detect ob­
jects that are a short distance ahead, off to the
side of your vehicle or moving into your lane.
- Objects th at are difficult to detect such as mo­
torcycles, vehicles with high ground clearance
or an overhanging load are detected late or not
detected at all.
- When driving through curves
¢page 90.
-With stationary objects ¢ page 90.
A WARNING ~
Always pay attention to traffic when adaptive
cruise control is switched on and braking
guard is active. As the driver, you are still re­
sponsible for starting and for maintaining
speed and distance to other objects. Braking
guard is used to assist you . The driver must
always take action to avoid a collision. The
driver is always responsible for braking at the
correct time.
- For safety reasons, do not use adaptive
cruise control when driving on roads with
many curves, when the road surface is in
poor condition and/or in bad weather (such
as ice, fog, gravel, heavy rain and hydroplan­ ing). Using the system under these condi­
tions increases the risk of an accident.
- Switch adaptive cruise control off tempora­
rily when driving in turning lanes, on ex­
pressway exits or in construction zones. This
prevents the vehicle from accelerating to
the stored speed when in these situations.
- The adaptive cruise control system will not
brake by itself if you put your foot on the ac ­
celerator pedal. Doing so can override the
speed and distance regulation.
- When approaching stationary objects such as stopped traffic, adaptive cruise control
will not respond and braking guard will have
limited function.
- The adaptive cruise control system and
braking guard do not react to people, ani­
mals, objects crossing the road or oncoming
objects.
- The function of the radar sensors can be af­
fected by reflective objects such as guard rails, the entrance to a tunnel, heavy rain or
ice.
~
89

Ass is t
_&. WARNING
- Improper use of adaptive cruise control can
cause collis ions, other accidents and serious
personal injury .
- Never let the comfort and convenience that
adaptive cruise control and braking guard
offer d istract you from the need to be alert
to traff ic conditions and the need to rema in
in full control of your vehicle at all times,
- Always remember that the adaptive cruise
contro l and braking guard have limits - they
will not slow the veh icle down or ma intain
the set distan ce when you drive towards a n
obstacle or something on or near the road
that is not moving, such as vehicles stopped in a traffic jam, a stalled or disabled vehicle .
If registered by the radar sensors, vehicles
or obstacles that are not moving can trigger
a collision warn ing and if confirmed by the
video camera, a n acute collision warning .
- Never follow a veh icle so closely that you
cannot stop your vehicle safe ly . The adap ­
t ive cr uise control cannot slow or brake the
vehicle safely when you fo llow another veh i­
cl e too close ly. Always remember that the
automa tic braking func tion cannot br ing the
vehicle to a sudden or emergency stop un­
der these condit ions .
- T o prevent unintended operation, always
switch ACC off when it is not being used .
(U) Note
The sensors can be displaced by impacts or
damage to the bumpe r, whee l housing and
underbody. That cou ld affect t he adaptive
cruise control system and braking guard .
Have an authorized Audi dealer or authorized
Audi Serv ice Facility check their function.
90
In curves
Applies to: vehicles with Audi adaptive cruise control
Fig. 92 Ex am ple: dri ving into a curv e
When dr iving into a curve c:::> fig. 92 and out of a
curve , the adapt ive cruise control may react to an
object in the neighboring lane and apply the brakes . Yo u can prevent that by pressing the ac­
ce le ra to r peda l br iefly.
Stationary objects
Applies to: vehicles with Audi adaptive cruise control
F ig . 93 Exam ple: object chang ing la nes a nd stat ion ary ob ·
jec t
The adaptive cru ise control system only reacts to
objects that are moving or t hat the system has
already detected as moving . For example, it can
react when a vehicle that has already been de­
tected @ turns or changes lanes, but adaptive
cruise control does not react to a stationary veh i­
cle @.

co
co
.... N
" N .... 0
00
<.,;) 'SI"
Switching on/off
App lies to: vehicles with Audi adaptive cruise contro l
Fig. 9 4 Operat ing leve r: sw itching o n and off
Fig. 95 Inst rument cluste r: adaptive cruise contro l
You can set any speed between 20 mph (30 km/
h) and 95 mph (150 km/h) .
Indicator lights and messages in the instrument
cluster display inform you about the current sit­
uation and setting.
An addit ional indicator appears in the Head-up
d isplay* .
Switching adaptiv e cruise control on
.,. Pull the lever toward you into position @
¢
fig . 94. ACC: standb y appears in the display.
Saving the speed and activating regulation
.. To save the current speed, p ress the ISETI
¢ fig . 94 button . The stored speed is shown in
the speedometer in the L ED l ine @ and appears
briefly in t he information line @ ¢
fig. 95 .
.,. To activate the regu lation whi le stationary, also
press the brake peda l.
Switching adaptive cruis e control off
.,. Push the lever away from you in to posi tion @
u nt il it clicks i nto place. The message
ACC : off
appears.
A ss ist
@ Indic ato r light s
•-adaptive cruise control is switched on. No
objects are detected ahead . The stored speed is
maintained .
• - An object ahead was detected . The adaptive
c ruise contro l system regu lates the speed and
distance to the object ahead and accelerates/
brakes automatically .
f:i-adaptive cruise control is switched on. An
object ahead was detected. Your vehicle remains
stopped and will not sta rt driving automatically .
• -The automatic braking is not enough to
mai ntai n a sufficie nt dis tance to an obje ct ahead.
You must intervene ¢
page 94, Request for
driver intervention .
© Instrument cluster display
If adaptive cru ise control is not shown in the in­
strument cl uster d isplay, you can call it up using
t h e m ultif unction steer ing whee l butto ns
¢page 21.
Based on the graphics in the display , you can de­
te rm ine if the system is maintain ing a distance to
t h e object ahead and what that d ist ance is .
No vehicle -No object ahead was detected .
White veh icle -An object ahead was detected.
Red vehicle -Request for driver intervention
~page 94.
Both arrow s on the scale © indicate the distance
to the object ahead. No arrow appears w hen the
vehicle is on an open road and t here is no object
ahead . If an object is detected ahead, the arrow
moves on the sca le .
The green zone on the s cale i ndicates the store
distance . For information on changing the dis ­
tance, refer to ¢
page 93. If the distance se ­
lected is exceeded or not reached , the arrow
moves into the red zone on the scale .
A WARNING
~~ --
If you press the !SET ! button when driv ing at
speeds below 20 mph (30 km/h), the vehicle
accelerates automatically up to 20 mph (30
91

Ass is t
km/h), which is the minimum speed that can
be set.
(D Tips
- If you switc h the ignition or the adapt ive
cruise control system off, the set speed is
erased for safety reasons.
- The electronic stabilization control (ESC)
and the anti-slip -regulation (ASR) are auto­
matically sw itched on when the adaptive
cruise control is switched on.
Changing the speed
Applies to: vehicles with Aud i adapt ive cruise control
0
,
•
0
F ig. 96 Operat ing lever: changing the speed
~ co N
0
±
~
.. To increase or red uce the speed in increments,
tap the lever up or down.
.. To increase or decrease the speed quickly,
hold
the lever up or down until the red LED@ reach­
es the desired speed
¢ page 91, fig . 95 .
After each change, the new stored speed appears
briefly in the information line ¢
page 91, fig. 95
@.
Driving in stop-and-go traffic
Applies to: veh icles with Aud i adapt ive cruise control
The adaptive cruise contro l system also assists
you in stop-and-go t raff ic.
Stopp ing automatically
If an object ahead stops, your veh icle w ill brake
and stay at a stop, w ith in the limits of the sys­
tem. The Start/Stop system* can be used as usu­
al.
92
Driving m anually
.. Tap the accelerator pedal, or
.. pull the lever toward you into pos ition @.
@ Tips
If an obst acle is detected when you r vehicle
starts moving, the dr iver intervent ion reques t
appears¢
page 94 . Your vehicle will drive
more slowly when starting. T his may a lso
h appen in some situations when there is no
apparent obstacle.
Interrupting cruise control
Applies to: vehicles with Audi adaptive cruise control
F ig . 9 7 Se lector lever
Requirement: adaptive cruise control must be
switched on .
Overriding cruise control
.. To accelerate ma nually, pull the lever toward
you into posit ion @ and hold it there . The mes­
sage
ACC: override appears. Or
.. press the accelerator peda l.
.. To resume cruise control, release the lever or
take your foot off the accelerator pedal.
Cancelin g cruise control whil e dri ving
.. Move the lever into position @. The message
ACC: standb y appears . Or
.. press the brake pedal.
.. To resume the stored speed, move the lever in­
to position @.
Canceling cruise control when stopped
.. Push the lever away from you into position @.
T he message
ACC : standby appears. ..,.

.. To resume cr uise control, press the b rake pedal
and pull the lever toward you into position @.
A WARNING
It is dangerous to activate cruise control and
resume the stored speed when the current
road, traffic or weather conditions do not per­
m it this. This increases the risk of an acc ident.
Setting the distance
App lies to: veh icles with Audi adaptive cruise contro l
Fig . 98 O perat 1ng leve r: set ting the d ista nce
.. Tap the switch to display the current set dis­
tance¢
fig. 98.
.. To increase or reduce the distance in incre­
ments, tap the switch again to the right or left .
The distance between the two vehicles w ill
change in the instrument cluste r d isplay.
When approach ing an object ahead, the adaptive
cru ise control system b rakes to match that speed
and the n adj usts to the set distance . If the ob ject
a head acce le ra tes, adapt ive cruise control will a l­
so acce le ra te up to the s to red speed .
The higher the speed, the greater the d istance in
meters ¢,&. . The
Distance 3 sett ing is recom­
mended. That i s equal to the genera l recommen­
dation of "ha lf the speed shown on the speedom ­
eter".
The distances prov ided are specified values . De­
pending on the d riving si tuation and the way the
ob ject ahead is d riving , the act ual d istance may
be mo re o r less t han t hese targe t dista nces.
co ~ The various symbols for the time increments ap-
~ pea rs briefly in the information line @
8 ¢ page 91, fig. 95 when yo u change the set tings. 00 <..:l 'SI"
A ss ist
c:::::, _c:::::, ___ Distance 1: this sett ing corresponds
to a distance of 92
ft (28 m) when traveling at 62
mph (100 km/h), for example (time between: 1
second).
c:::::, __ c:::::, __ Distance 2: this setting cor responds
to a distance of 118 ft (36 m) when traveling at
62 mp h (100 km/h), for example (time between:
1.3 seconds).
c:::::, ___ c:::::,_ Distance 3: this setting corres ponds
to a distance of 164 ft (SO m) when trave ling at
62 mp h (100 km/h), for example (time between:
1.8 seconds).
c:::::, ____ c:::::, Distance 4: This sett ing correspon ds
to a distance of 210 ft (6 4 m) when traveling at
62 mp h (100 km/h), (time distance of 2 .3 sec­
onds).
A WARNING
-Following other ve hicles too close ly incre .ases
the r isk of collisions a nd serious personal in­
ju ry.
- Sett ing s hort d ista nces to the traff ic ahead
reduces the time and distance available to b ring yo ur vehicle to a safe stop and makes
it even more necessa ry to pay close atten­
tion to t raffic.
- Always obey app licab le traffic laws, use
good judg men t, a nd se lect a safe following
di stance f or the traff ic, ro ad an d wea ther
condi tion s.
@ Tips
- Distance 3
is s et au tomatically each time
you swi tch the ign ition on.
- Yo ur sett ings a re automat ica lly stored and
assigned to the remote control key be ing
used .
Selecting the driving mode
Applies to: vehicles with Audi adaptive cruise control
.. Select the desire d driving mode in dr ive select
¢page 105 . ..,.
93

Ass is t
@ Tips
Your settings are automatica lly stored and as­
signed to the remote control key be ing used .
Request for driver intervention
App lies to: ve hicles w ith Audi adaptive cruise co ntro l
Fig . 99 Instrum ent clus te r: r eq ues t fo r drive r interve ntio n
In certain situations, the system w ill request you
to take action :
- if t he braking from the adapt ive cr uise control
system is no t enough to maintai n enough dis­
tance to the object ahead.
The dange r is ind icated by the . indicator light
~ fig. 99. An audio s ignal will also sound.
- Press the brake pedal to slow your vehicle down .
Audi braking guard
Applies to: ve hicles w ith Audi adaptive cruise co ntro l
Fig . 100 In str um ent clus te r: appro ach warning
The braking guard uses radar sensors and a video
camera .
It also functions within the limits of the
l) This is no t a vail able in som e coun trie s.
94
system when adaptive cru ise control is switched
off.
What can the braking guard do ?
When detected in time, the system can assess
dange rous si tu at ions where an object ahead
brakes sudden ly or if yo ur own vehicle is trave ling
at a h igh speed and approach ing an ob ject that is
moving more slow ly. The braking guard does not
react if it cannot detect the situation.
The system advises you of var ious dange rous sit­
uations :
- The
di stan ce warning occu rs if you dr ive too
close ly to the object ahead fo r a long per iod of
time .
If the object ahead brakes strongly, you
would not be ab le to avoid a co llis ion. The .
indicator light appears as an indication for this .
- T he
appr oach w arning occurs when an object
ahead is trave ling more slowly or brakes
strongly. When this warning occurs, it may only
be possible to avoid a collis ion by swerving or
brak ing strongly . The danger is indicated by the
• indicator light
¢fig. 100 . An audio signal
w ill also so und .
If you do not react early enough or at all to a dan ­
gerous situation, the braking guard supports you
with a braking intervention .
- If a co llision is imminent, the system wi ll first
provide an
acute warning by braking sharply .
- If you do not react to th e acute warning, the
b raking guard can inc rease the braking force
w ith in the lim its of the system
1> . This reduces
the vehicle speed in the event of a coll is ion.
- T he system can in itiate complete dece leration
shortly before a collision
l) . Full deceleration at
high speeds occurs only in veh icles with adap­
tive cruise control and side assist (pre se nse
plus) .
- If the braking guard determ ines that you are
not braking s trongly enough when the re is a n
impending coll is ion, it can increas e the b raking
force.
- The p re sense funct io ns also engage w hen
there is an impending collision ~
page 138.

co
co
.... N
" N .... 0
00
\.J ' Which functions can be controlled?
You can switch the braking guard and the dis­
tance/approach warning on or off in the Infotain­
ment system
c::, page 95 , Settings in the Info­
tainment system.
A WARNING
Lack of attention can cause collisions, other
accidents and serious personal injuries. The
braking guard is an assist system and cannot
prevent a collision by itself. The driver must
always intervene . The driver is always respon­
sible for braking at the correct time.
- Always pay close attention to traffic , even
when the braking guard is switched on . Be
ready to intervene and be ready to take
complete control whenever necessary. Al­
ways keep the safe and legal distance be­
tween your vehicle and vehicles up ahead.
- Braking guard works within limits and will
not respond outside the system limits, for
example when approaching a stopped vehi­
cle or stationary obstacle (end of a traffic
jam or vehicle that has broken down in traf­
fic).
- Always remember that the radar sensor for
the braking guard works only within defined
detection and range limits that may prevent
the proper detection of other vehicles .
- The radar sensor's function and range can
be reduced by rain, snow and heavy spray.
Moving vehicles up ahead may not be
promptly detected or may not be detected
at all.
- Reflective surfaces including crash barriers
or tunnel entrances may impair the function
of the radar sensor.
{!) Tips
- You can cancel the braking with increasing
force that is initiated by the system by brak­
ing yourself, by accelerating noticeably or
by swerving.
- Keep in mind that braking guard can brake
unexpectedly. Always secure any cargo or
objects that you are transporting to reduce
the risk of damage or injury .
Assist
Settings in the Infotainment system
Applies to: vehicles with Audi adaptive cruise control
.,. Select: the I CAR! function button > (Car)*Sys·
terns
control button > Driver assistance > Audi
braking guard.
System -
Switch the braking guard On/Off. When
you switch the ignition on, the message
Braking
guard: Off
appears if the system is switched off.
Early warning -The distance and approach warn­
ings in the display can be switched
On/Off.
(D Tips
- Your settings are automatically stored and
assigned to the remote control key being
used.
- If you restrict or switch off the ESC, the
braking guard also switches itself off
¢ page 121 .
-Switch braking guard off when you are load­
ing the vehicle onto a vehicle carrier, train,
ship or other type of transportation. This
can prevent undesired warnings from the
braking guard system.
Messages
Applies to : vehicles with Aud i adapt ive c ru ise control
Braking guard: Off
This message appears if the system is switched
off through the Infotainment system. Otherwise,
if the system is turned off, the information ap­
pears every time shortly after the start of the
trip .
The message also appears if the system is not
available due to a malfunction or if the ESC is
switched
off ¢page 121. If this is the case, the
system will not provide warnings about a possi­
ble collision.
Braking guard: engaged
This message appears if a sharp brake pressure
was applied due to an acute warning .
ACC: unavailable
ACC and Audi braking guard: Unavailable
95

Ass is t
The system cannot guarantee that it will detect
objects correctly and is switched off. The sensors
have been moved or are faulty. The pre sense
functions may also be affected. Dr ive to an au­
thor ized Audi dealer or authorized Audi Service
Facility immediately to have the malfunction cor ­
rected .
ACC: Currentl y unav ailabl e. No senso r vis ion
ACC and Audi braking guard : Curre ntly un avail­
a ble . No se nsor v ision
This message appea rs if the sensor view is ob­
s truc ted, for example by leaves, snow, heavy
spray or d irt. C lean the sensors ¢
page 89,
fig. 91.
ACC: Curre ntly unavailable. Gradient too steep
The road exceeds the max imum possible angle
for safe adapt ive cruise control operation . Adap­
tive c ruise contro l is switched off.
AC C: onl y availab le in D, S or M
Select the 0/5 or M selector lever position .
ACC: Currentl y unavailable . Parking brake ap •
pl ied
The adaptive c ruise contro l system switches off
automatically if the park ing bra ke is set.
ACC: Curre ntly unavail abl e. Stab ility control
( ESC) input .
This message appears if the Electronic Stabiliza­
tion Control (ESC) is tak ing action to stabilize the
ve hicle . In this case, adapt ive cruise control
sw itches off automatically.
AC C off: Manual control!
This message appears when adaptive cr uise con­
trol cannot set the parking brake . Press the brake
pedal to prevent the vehicle from rolling.
•••
Three white dots appear if a sett ing cannot be se­
lected wi th the ope rating lever. For example, this
h a ppens if adaptive c ruise cont ro l canno t start
driving automatically in stop -and-go traffic be­
cause the driver has not fastened their safety
be lt.
96
Door open
The adaptive cru ise cont rol system cannot switc h
o n when a door is open.
Stationary obj ect ah ead
This message appears if you wo uld like to switch
adaptive cruise control on and there is a station­
ary object or obstacle direct ly ahead of your vehi­
cle .
Audi active lane assist
Description
Appl ies to: vehicles with Audi act ive lane assist
Active lane assist detects lane marker lines with­
i n the lim its of the system using a camera in the
windshield. If you are approach ing a detected
lane marker line and it appears like ly that you
will leave the lane, the system w ill warn you with
corrective steering. You can override this steering
at any time. If you pass over a line, the steering
whee l w ill vibrate lightly. In orde r fo r thi s warn­
i ng vibration to occ ur, it must first be switched
on in the Infotainment system. Active lane ass ist
is ready for operation when the lane marker line
is detected on at least one side of the vehicle.
The system is des igned for driving on express­
ways and highways and therefore on ly activates
at speeds above approximately 40 mph (65 km/
h) .
Applies to: vehicles with side assist
If you activate a turn s ignal when act ive lane as­
s ist is ready and it classifies a lane change as crit ­
ica l because of vehicles traveling a longside you or
approach ing you, there wi ll be noticeable correc­
tive steer ing shortly before you leave the lane.
This will attempt to keep your veh icle in the lane.
Applies to: vehicles without side assist
The system will not wa rn you befo re c ross ing a
l ane marke r line if you have act ivated the t urn
s ignal. In this case, it assumes that you are
changing lanes intentionally.
Applies to: vehicles with adaptive cru ise control
The corrective steer ing is targeted based on the
driv ing situation . In add it ion to the lane marke r .,.

co
co
.... N
" N .... 0
00
<.,;) 'SI"
lines, the system c an also t ake into account other
objects such as guard rails . If they are detected in
close proximity to the veh icle, active lane assist
he lps prevent the vehicle from driving too close
to them. There is also passing assistance . The
system does not provide any corrective steering if
i t detects that you are passing another veh icle .
& WARNING
-The system wa rns the driver that the veh icle
is leav ing the lane using co rre ctive s teer ing.
T he driver is always respo nsible for kee ping
the vehicle within the lane .
- T he system can help you keep the vehicle in
th e lan e, but i t does not drive by itself. Al­
w ays keep yo ur hands on the steering
whee l.
- Corrective steer ing may not o ccur in ce rtain
situations , su ch as during heavy bra king.
- T here m ay be cases where the came ra does
not recognize all lane ma rker lines . Correc ­
t ive steering can o nly take p lace on the side
of the veh icle where lane marker lines are
detected.
- Other road structures or objects could possi­
bly be identified unintentiona lly as lane
marker lines . As a result, corrective steering
may be unexpected or may not occur.
- The camera view can be restricted, for ex­ ample by vehicles driv ing ahead or by rain,
snow, heavy spray or light shining into the
camera . This can result in act ive lane assist
not detec ting the lane marke r lines or de­
tecting them incor rectly.
- Under certa in conditions suc h as rut s in the
road, a bank ed roadway o r crosswinds , the
co rrective stee ring a lone may not be enough
to keep the vehicle in the mi ddle of the lane.
- F or safety reasons, active lane assis t m ust
not be used when the re are poor roa d an d/
o r we athe r cond itions s uch a s slippery
roads, fog, grave l, heavy r ain, snow a nd the
potent ial for hydroplaning . Using active lane
assist under these conditions may increase
the risk of a crash.
A ss ist
Switching on/off
App lies to : veh icles w it h A udi act ive lane ass ist
Fi g. 10 1 Turn s ignal leve r: bu tto n fo r active lan e ass is t
Fig . 1 02 W inds hield: came ra w indow fo r active lane a ssist
.,. Press the button to sw itch the sys tem on and
off c'.>fig .101. The .or. indicator light in
the inst rument cluste r turns o n or off .
Indicator lights
• Ready: the indicator light turns on when the
system is ready for use. The system can now be
operated .
• Not ready : the indicator light turns on if the
system is switched on but is inoperable. This may
be due to the following reasons:
- There is no lane marker line .
- The relevant lane mar ke r li nes a re not detected
(for examp le, ma rkings in a construction zone
or because they are obstructed by snow, dirt,
water or light ing).
- The vehicle speed is be low the activation speed
of approximate ly 40 mph (65 km/h) .
- The la ne is too nar row or too wide .
- The curve is too narrow.
- The d river's hands are not on the steer ing
wheel.
97

Ass is t
@ Tips
Make sure the camera's fie ld of view
¢
fig. 102 i s not obstructed by st ickers or any­
thing else. For information on cleaning, refer
to¢
page 235.
View in instrument cluster display
A ppl ies to: ve hicles w ith Audi active lane assist
Fig . 1 03 Instrument cl uster: act ive lane ass ist is sw itc hed
on a nd prov id ing warn ings
Fi g. 10 4 Inst rument cluster: act ive la ne assist is sw itc hed
on but not ready to provide warnings
You can call up the active lane assist display us­
ing the buttons in the multifunction steering
wheel ¢
page 21.
An addit iona l indicator appears in the Head -up
disp lay*.
White line(s) Active lane assist is activated and ready to p rov ide warnings.
Red line(s) Active lane assist warns you
(left or r ight) before leaving a lane
¢ fig. 103. In addit ion, the
steering wheel vibrates light ly.
Gray line(s) Active lane assist is activated,
b ut not ready to give warning
¢ fig . 104.
98
Messages in the instrument clu ster disp lay
If t he a ctive lane assist sw itches off automa tical­
l y, the indicator light in the display turns off and
one of the fo llow ing messages appears:
Audi a ctive lane assi st : Currentl y unavailable.
No camera v iew
This message appears if the camera is unable to
de tect the lines. This could happe n if:
- The camera field of view¢
page 97, fig. 102 is
dirty or covered in ice . Clean th is area on the
w indshield.
- The camera fie ld of view is fogged over. Wait
until the fog has cleared before switch ing the
active la ne assist on aga in .
- T he system has been unable to detect the lanes
for an extended p eriod of t ime due to road con­
ditions . Switch ac tive lane assist back on when
t he lines a re more visib le.
Audi a cti ve lane assi st: Currently unavailab le
There is a temporary act ive lane assist malfunc­
tion. Try switc hing the active lane assist on again
later.
Audi a cti ve l ane assist: System fault!
D rive to an au thor ized A udi dealer or au thorized
Audi Service Facility immediate ly to have the
malfunction corrected.
Audi active lane a ssis t : Plea se take over steering
This message appears if you are not steer ing by
yourself .
If this is the case, active lane assist does
not switch off, b ut it is "not ready" to provide a
warning. The system can help you keep the vehi­
cl e in the lane. However, you are responsible for
driv ing the vehicle and must steer it yourse lf .
Adjusting the vibration warning
App lies to: vehicles wit h Audi active la ne ass ist
.,. Select: the I CARI function button > (Car ) * Sys­
tems
contro l button > Dri ver assistan ce > Audi
a ct ive lane assist .
Vibrat ion warning
You can swi tch the addit io nal vib ra ti on war ning
in the steering whee l on or off .
Ill-