AUDI A7 2017 Owner´s Manual

co co .... N
" N .... 0
00
\.J ' use the recommended snow or all-season tires
specified for your vehicle, or their equivalent.
Refer to
~ page 22 7 for more deta iled i nfo rma­
tion rega rding win ter tires.
Uniform t ire quality grading
- Tread wear
- T raction AA A B C
- T emperatu re ABC
Quality grades ca n be found where applicable on
the ti re side wall between tread shoulder and
maximum sect ion w idth
¢ page 211, fig. 190.
For example: Tread wear 200, Traction AA, Tem­
perature A.
All passenger car tires must conform to Federal
Safety Requirements in addition to these grades.
Tread wea r
The
tr ead w ear grade is a comparat ive rating
based on the wear rate of the t ire when tested
under controlled conditions on a specified gov­
ernment test course.
F or examp le, a t ire graded 150 would wear one
and one ha lf
( 1 1/2) times as well on the govern ­
ment course as a tire graded
100 .
The relative perfo rmance of tires depends u po n
the actua l conditions of their use, however, and
may depart significant ly from the norm due to
va riations i n driving habits, service practices and
d ifferences in road characteristics and climate.
Traction
The
traction grades, from highest to lowest, are
AA, A, Band
C. T hose grades represent the tire's
ab ility to stop on wet pavement as measured un­
de r contro lled conditions on specified gove rn­
ment test surfaces of asphalt and concrete . A tire
marked C may have poor traction performance
¢ _& .
Temperatur e
The
temperature grades are A (the highest), B ,
and C, representing the tire's resistanc e to the
generation of heat and its ability to diss ipate
Wh eel s
heat when tested under cont rolled conditions on
a specified indoor laboratory test wheel.
Sustained high temperat ure can cause the mate­
r ia l of the tire to degenerate and reduce t ire life ,
and excessive tempera ture can lead to s udden
tire failure ¢,& .
T he grade
C corresponds to a level of perfo rm­
ance which all passenger car tires must meet un­
der the Federal Motor Vehicle Sa fety Standa rd
No.
109. Grades Band A represent higher levels
of pe rformance on the laboratory test wheel than
the minim um req uired by law.
A WARNING
-
The tract ion grade assigned to this t ire is
based o n straight -ahead braking traction
tests, and does no t include acceleration, co r­
n ering, hyd roplaning or pea k traction cha rac­
t erist ic s .
A WARNING
The temperature grade fo r this tire is estab­
lished for a tire that is properly infl,;1ted and
not overloaded . Excessive speed, underinfl a­
tion, o r excessive loading, either separately or
i n comb inat ion, can cause heat bu ildup and
possib le tire fai lure .
A WARNING
-
-Temperature grades apply to tires that are
p roperly inf lated and not ove r or under inflat­
ed.
Tire pressure monitoring system
(l) General notes
Each tire, including the spare (if provided),
shou ld be checked monthly when cold and inflat­
ed to the inflat io n pressure recommended by the
vehicle manufacture r on the veh icle placard or
t ir e infla tion p ressure labe l. (If your ve hicle has
t ir es of a diffe re nt si ze t han t he si ze ind icated on
t h e ve hicl e p lacard or tire inflat io n pres sure la­
bel, you sho uld dete rm ine the proper tire in fla-
t ion press ure for those tires) . ..,.
229

Wheels
As an added safety feature, your vehicle has been
equipped with a tire pressure mon itor ing system
(TPMS) that illuminates a low tire pressure tell­
tale when one or more of your tires is significant­
ly under-inflated . Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure . Driving on a signifi­
cantly under-inflated tire causes the tire to over­
heat and can lead to tire failure. Under-inflation
also reduces fuel efficiency and ti re tread life,
and may affect the vehicle's handling and stop­
ping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under- inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire
pressure telltale . When the system detects a
malfunction, the telltale will flash for approxi ­
mately one m inute and then remain cont inuously
illuminated . This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists .
When the malfunct ion indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the
TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
230
Tire pressure monitoring system
Applies to: vehicles with Tire Pressure Monitoring System in­
dicator
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Fig. 194 Instrumen t cl uster : indicator l ig ht with me ssage
Using the ABS sensors, the tire pressure monitor­
ing system compares the tire tread circumfer­
ence and vibration characteristics of the individu­
al tires. If the pressure changes in one or more
tires, this is indicated in the instrument cluster
display with an indicator light
Rt] and a message.
If only one tire is affected, the location of that
tire will be indicated.
The tire pressures must be stored in the Infotain­
ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle
¢ page 231. The tire pressure mon i­
toring system only monitors the tire pressure you have stored . Refer to the tire pressure label for
the recommended tire pressure for your vehicle
¢page 221, fig. 193.
Tire tread circumference and vibrat ion character­
istics can change and cause a tire pressure warn­
ing if :
- the tire pressure in one or more tires is too low.
- the tire has structural damage.
- the tire was replaced or the tire pressure was
changed and it was not stored¢
page 231 .
-the spare tire* is installed.
Indicator lights
RI]-Loss of pressure in at least one tire¢.&_ .
Check the tires and replace or repair if necessary . .,..

co
co
.... N
" N .... 0
00
\.J - Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
¢page 231.
ffim (T ire Pressure Monitoring System) T ire
pressu re : S ys tem malfunction !. If ffim
appears
after switching the ignition on or whi le driving
and the
[I] indicator light in the instrument clus­
ter blinks for approximate ly one minute and then
stays on, there is system malfunction. Try to
store the correct tire pressures¢
page 231. If
the ind icator light does turn off or turns on again
after a short period of time, dr ive to an author­
i zed A udi dealer o r authorized Audi Service Fac ili­
ty immediately to have the malfunc tion correct ­
ed .
& WARNING ,___ -
-If the tire pressure indicator appea rs in the
display, reduce your speed immed iate ly and
avoid any hard steer ing or braking maneu­
vers. Stop as soon as possib le and check the
t ires and their pressure.
- The driver is responsib le for maintaining the
correct tire pressure. You must check the
t ire pressure regu larly.
- Under certa in conditions (such as a sporty
driv ing style, winter cond itions or unpaved
roads), the tire p ressure monitoring system
indicator may be delayed.
{D) Tips
- The t ire pressure monitoring system can al­
so stop work ing when there is an ESC mal­
funct ion.
- Using snow chains may result in a system
malfunction .
- The t ire pressure monitoring system in your
Audi was calibrated with "Audi Orig inal
Tires"
¢ page 218. We recommend that you
use these t ires .
Wh eel s
Storing tire pressures
Applies to: vehicles with Tire Pressure Monitor ing System in­
dicator
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­ tem.
.,. Make sure before storing that the tire pressures
of all four tires meet the specified values and
are adapted to the load
¢ page 221.
.,. Switch the ignit ion on.
.,. Select: the
I CAR ! funct ion button > ( C ar) * Sys­
tem s
contro l button > S ervic e & ch eck s> Tire
pres sure monitor > Store tire pre ssure > Yes,
s tore now .
(D Tips
Do not store the tire pressures if snow chains
a re installed.
Tire pressure monitoring
system
ill General notes
Each tire, including the spare (if provided),
shou ld be checked monthly whe n cold and inflat­
ed to the i nflat io n press ure recommended by the
vehicle manufacturer on the veh icle placard or
t ir e inflation pressure labe l. (If your ve hicle has
tires of a different size than the size indicated on
the vehicle placard or tire inflation pressure la­
bel, you should determ ine the proper tire infla­
t ion pressure for those tires).
As an added safety feature, yo ur vehicle has been
equipped with a tire pressure mon itor ing system
(TPMS) that illuminates a low tire pressure tell­
ta le when one or more of your tires is signif icant­
ly under-inflated. According ly, when the low t ire
pressure te lltale illum inates, you sho uld stop and
chec k your tires as soon as possib le, and inflate
t h em to the prope r pressure. Dr iving on a sig nifi­
ca nt ly unde r-inflated t ire causes the t ire to over ­
hea t and can lead to tire fa il ur e. Under-inflat ion
also reduces fue l effic iency and tire tread life,
and may affect the vehicle's handling and stop -
ping ability .
liJJ,-
231

Wheels
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsib ility to ma intain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your veh icle has also been equ ipped with a TPMS
malfunction indicator to indicate when the sys ­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire
pressure telltale . When the system detects a
malfunction, the telltale will flash for approxi­ mately one minute and then remain cont inuously
illum inated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists.
When the malfunct ion indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS ma lfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate t ires and
wheels a llow the TPMS to continue to function
properly.
Description
A pp lies to: ve hicles w ith tire p ressure monitoring system
The tire pressure monitoring system monitors
the pressure in the four tires when driving.
The system uses sensors that measure the tem ­
perature and pressure in the tires . The data is
sent from these sensors to the contro l module by
radio frequency.
The Tire Pressure Monitoring System shows the current pressures and temperatures of the tir es
in the Infota inment system
c:> page 232. It also
compares the current t ire pressures with the
stored tire pressu res and gives a warning in the
d river information system if the tire pressure is
different from what is stored
r:';> page 233.
232
The system does not detect if the stored tire
pressures match the recommended tire pres­
sures. You must store the tire pressures again
c:> page 233:
-every time the tire pressures change, for exam ­
ple when the load in the vehicle changes,
- after replacing a tire, or
- if wheels with new whee l sensors are used.
_&. WARNING
- The tire pressure monitoring system assists
the driver in monitoring tire pressures. The
driver is responsib le for having the tires in­
flated to the correct pressure.
- Do not change the tire pressure when the
temperature of the tire is high. This could
result in serious damage to the tire and
even cause the tire to burst, increasing the
risk of an accident.
-A tire with low pressure flexes more. This heats the tire up too much. This could cause
the tread to separate and even cause the
tire to burst, increasing the risk of an acc i­
dent.
- The tire pressure monitoring system does
not warn about damage or defects in the
tire construct ion that could cause the tire to
burst, for examp le. Inspect your tires reg u­
larly.
(D Tips
- If tires are replaced, the sensors/valves do
not need to be removed or replaced. Just re­
placed the va lve stem and, if necessary, the
valve and the wheel electronics.
If you have
questions, see your authorized Audi dealer
or authorized Audi Service Facility.
- An incorrect display or a malfunction in the
tire pressure monitoring system can occur
after using the tire mobility kit. Have the
sensors rep laced by an authorized Audi
dealer or author ized Audi Service Facility.
Displaying tire pressures/temperatures
App lies to: vehicles wit h tire pressure monitoring syste m
Requirement: the ignition must be switched on . ...,

co
co
.... N
" N .... 0
00
<.,;) 'SI"
.. Se lect: the I CAR I function button > Car syst ems
> Se rvice & checks > Tire pres sure monitor >
Di splay ti re pres sure s.
The cu rrent tire press ures are shown in green and
ye llow numbers in the Infotainment system:
- Green : the cur ren t tire pressure and the speci­
fied tire press ure are app roxima tely the same.
- Yellow : the cu rrent tire pressu re is too low
comp ared to the specified ti re pressure.
The spec ified tire pressure is the last tire pres­
sure that was stored
c> page 233 .
Note that the tire pressure also depends on the
temperature of the t ire . The tire press ure in­
creases as the engine becomes warmer wh ile
d riving.
..&, WARNING
Read and follow the important inform ation
an d no tes
c> page 232.
@ Tips
The tire pressure or temperature a re not dis­
played in adaptation mode. Dashes --.-- are
show n in place of the press ure and tempe ra ­
ture.
CD Tire pressure loss
A pp lies to: ve hicles with tire p ressu re m oni toring sys tem
F ig . 19 5 Display : indicato r lig ht wit h a me ssage
If t he RI) indicato r light turns on, t he p ressure in
at least one t ire is too low o r new sensors were
n o t adapted :
Wheels
II] indicator light s turns on after turning the
ignition on
T he tire press ure is too low compared to the
specified press ure .
.. Check and store the tire pressure(s) the next
time it is possible
<:!> page 233 .
HE indicator light turns on while driving
Wheels with new sensors we re not adapted or
t h e tire p ressure h as reac hed a cr itica l level com­
pared to the specified p ressure.
.,. Avoid unnecessary steer ing and brak ing mane u-
vers.
.. Adapt your dr iving sty le to the sit uation.
.. Stop as soon as poss ible and check the tire(s).
.. If i t is possib le to continue dr iving , see an au-
thorized A udi dealer or authorized Audi Service
Facility immediately and have your tire(s) re­
paired or rep laced.
..&, WARNING
--
Read and follow the important info rmation
and notes
r=> page232 .
Storing new tire pressures
Applies to: vehicles wit h tire pressure monito rin g system
Correctly stored t ire pressure specifications are
necessary for reliable tire pressure monitoring.
.. Check the tire pressures in all whee ls .
.. Correct the t ire pressure if necessary . Refer to
the ti re pressure label for the recommended
tire pressure for your vehicle
c> page 221,
fig . 193.
On ly co rrect the pressure i n tires
whose temperature is app roximately the same
as the a mbient tempe ra tu re.
If the tempe ra­
t ure of t he tire is higher than t he ambien t air
t em pe rature, the t ire press ure must be in­
creased approximately 3 PSI (0, 2 bar) above
the value on the sticker .
.. Switch t he ignit ion on.
.. Select:
!CAR I function button> Car systems >
T ire pressure monitoring > Store tire pressu re.
After stori ng, the t ire pressure monitori ng sys­
tem meas ures t he curre nt t ire pressures and
sto res them as the new specified pressures .
233

Wheels
"'If the changed tire pressures are not displayed
in the Infotainment system, drive the vehicle
for approximately 10 minutes so that the sen­
sor signal from the wheels is received again.
During this adaptation phase, --.--is displayed
for the pressure and temperature and the tire
pressure monitoring system is only partially
available. It only provides a warning if one or
more t ire pressures is below the minimum per­
mitted specified pressure. If this is the case, the
Rt] indicator light appears with a message.
_& WARNING
Read and follow the important information
and notes
r::!;>page 232.
Malfunctions
Appl ies to : vehicles wi th tire pressure mo nito rin g system
If the Tire Pressure Monitoring System is not
avai lable, the
mm indicator light appears in the
driver information system. The
Rt] indicator light
also blinks for approximately one minutes each
time the ignition is switched on. The tire pressure
monitoring system cannot be selected in the In­
fotainment system. The following are examples
of situations that could cause a malfunction:
- If the message appears at the end of the adap­
tation phase, the system cannot detect the
wheels installed on the vehicle. This may result
from one or more wheels being installed with­ out wheel sensors or with incompatible wheel
sensors.
- A wheel sensor or another component has
failed.
- Using snow chains can affect the function of
the system because of the shield ing effect of
the cha ins.
- The tire pressure monitoring system is not
available due to a malfunction .
- Transmitters with the same frequency, such as
headphones or remote-controlled devices, may
cause a temporary system malfunction due to
the strong electromagnetic field.
The
mm indicator light turns off once the Tire
Pressure Monitoring System is available again.
If
you cannot correct the malfunction and the mm
234
indicator light stays on, drive immediately to an
authorized Audi dealer or authorized Audi Service Facility to have the malfunction repaired.

co
co
.... N
" N .... 0
00
\.J ' Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value.
It can a lso be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The necessary care products can be obtained
from an authorized Audi dealer or authorized
Audi Service Facility . Read and follow the instruc­
tions for use on the packaging.
A WARNING
- Us ing clean ing and care products incorrectly
can be dangerous to your health.
- Always store clean ing and care products out
of reach of children to reduce the r isk of po i­
soning .
@ For the sake of the environment
- Preferably purchase env ironmenta lly-friend­
l y cleaning products.
- Do not d ispose of leftover cleaning and care
products with household trash.
Car washes
T he longer that deposits remain on the vehicle,
the more the surface may be damaged. High
temperatures such as those caused by sunlight
increase the damag ing effect.
Befor e washing, rinse
off heavy depos its with
p lenty of water.
S tubborn depos its such as bird droppings or tree
sap are best removed with plenty of water and a
microfiber cloth.
A lso, wash t he un derside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washing your ve hicles w ith a pressure
washer, always follow t he ope rating inst ructions
p rovided w ith the pressure washe r. This is espe ­
cially important in regard to the pressu re and
sp raying distance. Do not a im the spray directly
at the sea ls on the side w indows, doors, lids or
Ca re and cleaning
the sun roof * or at tires, rubber hoses, ins ulating
material, sensors* or camera lenses* . Keep a dis­
tance of at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone noz zles o r high pressu re noz zles .
The water temperature must not be above 140 °F
(60 °C).
Automat ic car washe s
Spray off the vehicle befo re washing .
Make s ure that the wi ndows and roo f* are closed
and the windsh ie ld wipers are
off . Follow instruc ­
tions from the car wash operator, especially if
there are accessories attached to your vehicle .
If possible, use car washes that do not have
brushes .
Applies to: RS models: only use car washes where
t h e vehi cle rema ins s ta ti onary and the washi ng
equipmen t moves around the veh icle when wash ­
ing and drying. Car washes that move the ve hicle
th rough the car wash using a chain are not rec­
ommended.
Washing by hand
Clean the ve hicl e s tarting from the top and wor k­
ing down using a soft sponge or cleaning br ush .
Use solvent -free cleaning products.
Washing vehicles with matte finish paint by
hand
T o avo id damag ing the pa int when washing, firs t
remove dust and large pa rticles from your vehi­
cle . Insects, grease spots and fingerprints are
best removed w ith a special cleaner for matte
finish paint.
Apply the product using a microfiber cloth . To
avo id damaging the pa int surface, do not use too
much pressure .
Rinse the ve hicl e thorough ly w ith wate r. Then
clean using a neutra l shampoo and a so ft micro ­
fiber cloth .
Rinse the ve hicl e thoroug hly aga in and let it air
dry . Remove any water residue using a chamois. ..,.
235

Care and cleaning
A WARNING
- Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
-After washing the vehicle, the braking effect
may be delayed due to mo isture on the
brake rotors or ice in the winter . This in­
creases the risk of an acc ident. The brakes
must be d ried first w ith a few careful b rake
applications.
(D Note
- If yo u wash the ve hicle in an automatic car
wash, yo u m ust retract the rear spoiler if
necessary, and fold the exte rior mi rrors in
to reduce the risk of da mage. Power fo ld ing
ex ter ior mirro rs* m ust only be folded in and
out using the power folding func tion.
-
- To red uce the risk of pa int damage, do not
wash the vehicle in direct sun light .
- T o reduce the risk of damage to the s urface,
do not use insect removing sponges, kitchen
sponges o r similar items .
- Matte finish painted vehicle components:
-To reduce the risk of damage to the sur-
face, do not use polis hing agents or hard
wax .
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint. The paint could be damaged
when the stickers or magnets are re­
moved.
@ For the sake of the environment
Only wash the veh icle in facili ties spec ially de­
s igned for that pu rpose . This will reduce the
r isk of dirty wate r contam inated with o il from
ente ring the sewe r system.
Cleaning and care information
W hen clean ing and ca ring for ind ividua l vehicle
components, refer to the fo llow ing tables. The
i n formation conta ined there is s imply recom­
mendations. For quest ions or for components t
h at are not listed, cons ult an autho rize d Aud i
dealer or au thor ized Aud i Servi ce Fac ility. Also
fo llow the informa tion found in <=> & .
Ext erior cleaning
Component Situation Solution
Windshield wiper
Deposits ¢ page 47, Cleaning windshield wiper blades
blades
Headlights /
Deposits Soft sponge wi th a m ild soap solution3>
Tail light s
Sensors /
Deposits Sensors: soft cloth with solvent-free cleaning solution
camera lens es Camera lenses: soft cloth w ith alcohol -free cleaning solu -
tion
Snow/ice Hand br ush/solvent-free de-icing spray
Wheels Road salt Water
Bra ke dust Acid-free special cleaning solution
Exhaust tail pipes Road salt Water, clea ning solution su itab le for s tainl ess stee l, if nee-
essa ry
236

co
co
.... N
" N .... 0
00
\.J ' Care and cleaning
Component Situation Solution
Decorati ve parts /
Deposits Mild
soap solution al, a cleaning so lution suitable for stain-
less stee l, if necessary
trim
Paint
P aint damage Refer to the paint number on the vehicle data label, repair
with touch up paint
q page 260
Spilled fuel Rinse with water immediately
Surface rust Rust
remover, then protect with hard wax; for questions,
consult an authorized Audi dealer or authorized Audi Serv-
ice Facility.
Corrosion Have it removed by an authorized Aud i dealer or author-
ized Audi Se rvice Facility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable polish; then app ly paint protectant if
paint has been pro -the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in - Dampen with water immediately and remove with a m icro-
sects, bird droppings,
fiber cloth
tree sap and road salt
Grease-based con- Remove immediately with a m ild soap solution al and a
taminants such as soft cloth
cosmetics or sunb lock
Carbon parts Deposits clean the same way as painted parts q page 235
a} Mi
ld soap solution: maximum two tab lespoons of neutral soap in 1 quart (1 lite r) of water
Interior cleaning
Component Situation Solution
Windows
Deposits Glass cleaner, then wipe dry
Decorative parts/ Deposits Mild
soap solutional
trim
Plastic parts
Deposits Damp cloth
Heavier deposits Mild soap solution al, detergent-free plastic cleaning solu-
tion, if necessary
Display s Deposits Soft cloth with LCD cleaner
Controls Deposits Soft brush, then a soft cloth with a m ild soap solutional
Safety belts Deposits Mild
soap so lution al, allow to dry before letting them re-
tract
237

Care and cleaning
Component Situation Solution
Te xtil es
Deposits adhering to Vacuum cleaner
a rt ifici al le ather , the surface
Alcant ara Water-based deposits Absorben
t cloth and mild soap solutiona>
such as coffee, tea,
blood, etc.
O il-based deposits Apply a m ild soap solution a), blot away the dissolved oil or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Special stain remover, b lot with absorbent material, treat
as ink, na il polish, la- afterward with mild soap solution, if necessary a)
tex paint, shoe pol-
ish, etc.
Natural leather Fresh stains Cotton cloth with a mi
ld soap solutiona>
Water-based deposits Fresh sta ins : absorbent cloth
such as coffee, tea, Dried sta ins: stain remover suitable fo r leather
blood, etc.
Oil-based deposits Fresh stains: absorbent cloth and stain remover suitable
such as oil, make-up, for leather
etc. Dried sta ins : grease dissolv ing spray
Special deposits such Spot remover suitab le for leather
as ink, nai l polish, la -
tex paint, shoe pol-
ish, etc.
Ca re Regularly apply cond ition ing cream that protects from
light and penet rates into the materia l. Use specia lly-co l-
ored conditioning cream, if necessary.
Carbon parts Deposits clean the same way as plastic parts
a) Mild soap solution: maximum two tablesp oons of neutral soap in 1 quart (l liter) of water
_& WARNING
The windshie ld may not be trea ted with wa­
ter-repelling windshield coating agents. Un­
favorable conditions s uch as wetness, dark­
ness, or low sun can result in increased glare .
Wiper blade chatter is also possible.
(D Note
- Headlights /tail light s
-Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcohol, because they could cause
cracks to form.
- Wheels
238
-
- Never use any paint polish or other abra­
sive materials.
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately.
- Sensors /camera l enses
- Neve r use wa rm or ho t water to remove
snow or ice from the camera lens . This
could cause the lens to crack .
- Neve r use ab rasive cleaning materials or
a lcohol to clea n the camera lens . This
could cause scratches and cracks .
-Doo r window s
-Remove snow and ice on windows and ex-
terior mirrors with a plast ic scraper. To