display AUDI Q5 2017 Service Manual

Hybrid
Start-Stop function
The combustion engine is operated on ly as need­
ed . Generally, the combustion engine turns off
when the vehicle is stationary and the high volt­
age battery powers the electrical vehicle sys ­
tems.
The purpose o f automatica lly shutting the com­
bustion engine off in hybrid drive mode is to save
fuel. All of the important vehicle systems, such
as steering, brakes and the A/C system, continue
to remain active. In some cases , systems may re­
qu ire the combustion eng ine to continue running
when the vehicle is stationary . When dr iv ing in
congested traff ic for long per iods of t ime, the
combustion eng ine will cycle on when the veh icle
is stationary to keep the high voltage battery
charged.
Gliding
If the gas pedal is not pressed and the D posit ion
is selected, the combustion engine remains
turned off up to speeds of approximately 99 mph
(160 km/h) . Driving conservative ly like th is can
reduce fuel con5umption .
Energy recovery (recuperation)
When braking, the electric motor will act as a
generator creating e lectr ic energy that is then
sto red in the high voltage battery. This also oc­
curs when the vehicle is coasting or driving down­
hi ll. The combustion engine is automat ica lly
turned off in this case .
Tips for Driving Efficiently with your Hybrid
Appl ies to: ve hicles w ith hyb rid drive
Driving situa- Conditions
tions
- Shift into the D position .
Starting from a -
Release the brake pedal. The vehicle is braked with
the electric motor by
applying early and even pressure to the brakes
and using short pedal movements
¢ page 101,
fig. 116 @. By doing this, a large amount of the
kinet ic energy is recovered and may be stored as
electric energy in the high voltage battery. Dur ­
i ng heavy brak ing , the conventional brakes are al­
so act ivated
¢ page 101, fig . 116 @.
The energy recovery is shown in the MMI display
¢page 107 .
Automatic start of the combustion engine
Various operating conditions cause the combus ­
tion eng ine to start automatically:
- Th e high voltage battery charge level is low.
- Th e temperature of the combustion engine is
low .
- Th e temperature of the catalytic converter is
low .
- T he power output needed for the A/C system is
high.
- The vehicle speed is high .
- The vehicle acceleration is high .
- The incline is steep .
- High charge level for the high voltage battery
when coasting. In this case, the high voltage battery cannot absorb any more energy and so
the electric motor cannot slow down the veh i­
cle. The combust ion engine turns o n (engine
brake) . In this situation the high voltage bat­
t ery w ill show a Max charge.
Vehicle behavior
In the D posit ion, the hybrid system adapts
to the driving situat ion by automatically
stop -
Only press moderately on the ac- sw
itch ing between the combustion engine
and e lectr ic drive types or by combining
celerator pedal.
them.
104
...

Hybrid Energy flow display
Applies to: ve hicles w ith hybri d drive
Fig. 118 Instrument cluster: energy flow display
The energy flow of the hybrid system is shown in
the instrument cluster display and in the MMI
d isplay. The image is animated in the MMI dis­
play .
Image in the instrument cluster display
.. Press the I RESET I button in the windshie ld wip­
er lever repeatedly until the energy flow display
r::> fig. 118 appears.
Component Color
@Combust ion engine orange
gray
@ Propshaft green
orange
green-orange
gray
@ H igh voltage battery green
green (animated in
MMI)
gray
@ Movement arrow green
orange green-orange
@ Movement arrow green
106
Fig. 119 MMI display: energy flow display
Image in the MMI display
.,. Select: !MENUI function button> Hybrid control
button
r::!) fig. 119 .
Meaning
The combustion engine is running
The combustion engine is off
Electric driving/recuperating
Driving with t he combustion engine
Driving w ith the combustion engine and electric
motor (boost)
Vehicle stationary/rolling in the N selector lever
position
High voltage battery charge level
High voltage battery is charging
Vehicl e is not in dr ive ready mode
Electric driving
Driving with the combustion engine
Driving with the combustion engine and electric
motor (boost)
Recuperating

a,
a,
..... N ,-... N ..... 0 0
0:
co
@ Tips
The Energy flow display will not shown in the
MMI display when the reverse gear is engag­
ed, due to safety reasons .
Consumption display
Applies to: vehicles with hybrid drive
Fig . 1 20 MMI displa y: co nsump tio n dis play
T he consumption d isplay shows the average en ­
ergy consumption and the rec uperation quantity
i n 5 minute interva ls .
Calling up the consumption display
... Select : I MENU I function button> Hybrid control
button .
... Turn the cont rol knob co unter -clockwise.
Resetting the consumption displ ay
... Se lect : I MENU I function button > Hybrid cont rol
button .
... Turn the control knob to
Reset consumpt ion
stat ist ics .
The orange bars show the average consumption
and the green bars show the recuperation quanti­
ty . Each bar represents a measured
5 minute in­
terval. The display covers a
60 m inute time peri ­
od .
The bar w ith the wh ite border on the outer right
shows the current average consumption or the
cur rent recupe ration q uantity. After 5 minutes,
this bar trave ls a step to the left and a new bar
a p pears in the outer right .
The filled bars show the values for the curren t
drive cycle . Once the ignition is sw itched off and
on aga in, all of the prev ious bars are display ed as
H ybrid
not fi lled and new fi lled bars a ppear on the right.
T his is so t hat the values from the previous t rips
and the current trip can be compared v isua lly.
Vehicle tool kit and tire repair set
Applies to: vehicles with hybrid drive
Fig. 121 L uggage compar tm ent: ve hicle too l bag an d tir e
r epa ir set
The veh icle tool k it is fou nd u nder a cover in the
cargo floor
c::> fig. 121 @ . The ti re repa ir set (T ire
Mobility System) is fo und in the storage com­
partmen t in the r ight side trim p anel @.
Additional informat ion about t he vehicle too l kit
may be found under
c::> page 250 and about the
t ir e repa ir set un der
c::> page 253 .
@ Tips
The right sto rage compartment in t he lug­
gage compartment and its co nte nts must al­
w ays be kept in the vehicle. The vehicle must
not be o per ate d w it h ou t the tire repair set.
Charging the batteries
Applies to: vehicles with hybrid drive
The vehicle is eq uip ped w it h t wo 12 volt ba tteries
and a high vo ltage battery .
If the 12 vo lt batte ries are dead, they may be
ch arged wi th a charger or the vehicle may be
j u mp s tarted wi th assis tan ce from ano ther veh i­
cl e in the same way as a conventional vehicle.
T he same app lies to the hig h vol tag e batte ry if it
is d isch arged. However, in this ca se, the ch ar gin g
proces s is ac compa nied wi th messages in t he in ­
strument cl uster d is p lay . T he ignition mus t be
switched on and a ll unnecessary e lectric compo-
nents must be turned off . ""
107

Hybrid
The connections in the engine compartment are
used for both charging and jump starting
c::> page 22 7 or c::> page 266.
Vehicle not ready to start. See owner's
manual
This message appears if the high voltage battery
charge level is too low. The vehicle can no longer
be started with its own power. The high voltage
battery must be charged with a charger or the ve­
h icle must be jump started with the aid of anoth­
er vehicle.
After the connecting the charger or jumper ca­
bles, the ignition must be turned off for approxi­
mately two minutes and then turned on again .
After no more than one m inute, one of the fol­
lowing indicator lights turns on in the instrument
cluste r display .
B Charging battery. Please wait ...
If the indicator light turns on and this message
appears, the high voltage battery is charg ing or
the vehicle is be ing jump started with assistance
from another veh icle .
If the 12 volt batteries are dead, the- indi­
cator light turns on . The charging procedure
takes longer in this case because the 12 volt bat­
ter ies are charged first. The procedure goes fast­
er with the ig nition sw itched off.
Vehicle ready to start.
This message appears if the charging procedure
was successful. The vehicle may be started again .
Battery could not be charged enough to start
vehicle .
This message appears if the charging procedure
was not successful or it was interrupted. Th is
may happen if the charger or the battery in the
veh icle that is assisting is too weak.
If the veh icle
can not be started, see an authorized repa ir facil i­
ty for ass istanc e.
(D Tips
-The charger should deliver a current of at
l east 30 A. Otherwise charging the high
voltage battery will take considerably Ion-
108
ger. A current between 50 A and 70 A is ide ­
al.
- Th e veh icle that is assisting should be some­
what within the same vehicle class when
jump starting a vehicle. A smaller vehicle's
battery may be drained.
- After approximately 30 minutes, the charg­
ing procedure ends because the ignit ion is
automatically turned off. If you would like
to cont inue to charge the battery, turn the
ignition on again.
Vehicle transport
App lies to: vehicles wit h hybrid drive
The following contains information you should
know about transporting your vehicle.
The lithium ion battery (SANYO 72 UF 121 285)
installed in your vehicle has passed test 38.3 in
accordance with UN handbook tests and criteria.
The vehicle may be transported with the battery
i nstalled as conventional class 9 hazardous mate­
rials without addit ional officia l consent for a ir
and sea transportation (current law !CAO-TI and
IMDG-Code 01.01.2012).

a,
a,
..... N r-­N ..... 0 0
0:
co
Audi adaptive cruise control and braking guard
Audi adaptive cruise control
Description
Applies to: veh icles with Audi adaptive cruise control
Fig . 12 5 Detect ion ra nge
What can adaptive cruise control do?
The adaptive c ruise co ntro l works in conjunct io n
wi th a radar sensor installed in th e front of th e
ve hicl e
¢page 109, fig. 122, which is sub je ct to
d es ign ated system lim it s ¢
page 111 . Stationary
objects are disregar ded.
On ope n ro ads wi th no traffic, adapt ive cr uise
con trol wo rks like a reg ular cruise contro l sys­
tem. The store d speed is m aintai ned. Whe n ap ­
p roaching a moving vehicle de tected u p ahead,
the adaptive cruise cont rol system automatically
slows down to match that vehicle's speed and then maintains the distance that the driver previ­
ously store d. As soon as the system does not de­
tect a vehicle up ahead, adaptive cru ise control
accelerates back up to the sto red speed .
Which functions can be controlled?
When you sw itch adaptive cruise cont rol on, yo u
can set the current speed as the "control speed"
¢ page 111, Switching on and off.
W hen driving , you can stop cruise contro l
¢page 113 or change the s peed ¢ page 112 at
any time.
You can a lso set the dis tance to the objec t ahead
and set t he a dapt ive cruise contro l driv ing pro­
g ram
¢ page 113.
Switching on and off
Applies to: vehicles with Audi adapt ive cr uise control
Fig . 126 Selector leve r: sw itc hin g on/o ff
Fig. 12 7 Instru ment clus te r: ad apt ive cru ise co ntrol
You can set a ny speed between 20 mph and
95 mp h (30 a nd 150 km/h).
Ind icator lamps and messages in the instr ument
cluster disp lay inform yo u about the current sys­
tem status and settings.
Switching adaptive crui se control on
.,.. Pull the lever towa rd yo u into position (!)
¢
fig . 126. ACC: Standby appears in the inst ru­
ment cluste r display .
Setting the speed and activating regulation
.,.. To se t the curren t speed, press t he ISE TI bu tton
¢
fig. 126. The set spee d is show n in the tach ­
ometer @ and is also shown br iefly in the dis­
play @¢
fig. 127.
Switching adaptive cruise control off
.,.. Push the leve r away fr om yo u into position @
until it cli cks into p lace. The message ACC: Off
appears. ..,..
111

Audi adaptive cruise control and braking guard
@ Indicator lights
Ill -Adaptive cruise control is switched on. No
vehicles are detected up ahead. The stored speed
is maintained .
• -A moving veh icle is detected up ahead. The
adaptive cruise control system regulates the
speed and distance to the moving vehicle ahead
and accelerates/brakes automatically.
• -When automatic braking is not able to keep
enough distance to a previously detected moving
vehicle up ahead, you must take contro l and
brake
¢ page 114, Request for driver interven­
tion.
© Display
If
adaptive cruise control is not shown in the dis­
play, you can call it up with the
IRESETI button
¢page 17.
Based on the symbo ls in the display, you can de­
termine if the system is ma inta ining a distance to
the vehicle ahead and what that distance is .
No vehicle -No vehicle ahead was detected .
White vehicle -A vehicle ahead was detected.
Red vehicle -Prompt for the driver to take action
¢page 114.
Both arrows on the scale© indicate the distance
to the vehicle ahead . No arrow appears when the
veh icle is on an open road and there is no object
ahead. If an object is detected ahead, the arrow
moves on the scale .
The green zone on the scale shows the stored dis­
tance . For information on changing the stored
distance, refer to
¢page 113. If the distance se­
lected is too close or may soon become too close,
the arrows move into the red zone on the scale .
A WARNING
Improper use of the adaptive cruise control
can cause collis ions, other accidents and seri­
ous personal injuries.
- Pressing the
! SET ! button when driving at
speeds below 20 mph (30 km/h), will auto­
matically accelerate the vehicle to 20 mph
112
(30 km/h), which is the minimum speed
that can be set.
@ Tips
- If you switch the ign it ion or the adaptive
cruise control off, the set speed is erased
from the system memory.
- The Electronic Stabilization Control (ESC) is
automatically turned on when the adapt ive
cruise control is turned on. You cannot
switch the ESC into offroad mode while the
adaptive cruise control is turned on
¢page 187.
Changing the speed
App lies to: vehicles with Audi adaptive cru ise control
0
f
•
0
Fig. 128 Selector lever: ch an gin g the speed
.,. To increase or reduce the speed in increments,
tap the lever up or down.
.,. To increase or reduce the speed quickly,
hold
the lever up or down until the red LED @ reach­
es the desired speed
¢page 111, fig . 127 .
Follow ing any changes, the new stored speed will
be displayed br iefly in the display @¢
page 111,
fig . 127 .

a,
a,
..... N r-­N ..... 0 0
0:
co
Audi adaptive cruise control and braking guard
Interrupting cruise control
Applies to: vehicles with Audi adaptive cruise contro l
Fig. 129 Selector lever
Requirement: adaptive cruise control must be
switched on ¢
fig. 129 (D.
Overriding cruise control
• To accelerate manua lly, press the accelerator
pedal. The message
ACC: override appears.
• To resume adaptive cruise control, remove your
foot from the gas pedal. The system returns again to the speed that was saved before .
• You can save a new speed at any time by press­
i ng the
ISET I button ¢fig. 129.
Canceling cruise control while driving
• Move the lever into position @. The message
ACC: Standby appears. Or
• press the brake pedal.
• To resume the stored speed, move the lever in­
to posit ion
@ .
& WARNING
Never resume the stored speed if the speed is
too high for prevailing road, traffic or weather
conditions.
Setting the distance
Applies to: vehicles with Audi adaptive cruise control
Fig. 130 Selector lever: setting the distance
• Tap the switch to display the current set dis­
tance ¢
fig. 130.
• To increase or reduce the d istance by incre­
ments, tap the switch aga in to the left or right.
The distance between the two veh icles will
change in the instrument cluster display.
When approaching a moving vehicle up ahead,
the adaptive cruise control system brakes to
match that object's speed and then maintains
the stored distance.
If the vehicle ahead acceler­
ates, adaptive cruise control will also accelerate
up to the stored speed .
The higher the speed, the greater the distance in
yards (meters) ¢.& .T he
Distance 3 setting is
recommended .
T he distances provided a re spec ified values . De­
pending on the driving situation and the how the
vehicle ahead is driving, the actual distance may
be more or less than these target distances .
T he various symbo ls for the time inc rements ap­
pear briefly in the info rmat ion line @
¢page 111, fig. 127when yo u change the set­
tings.
c::::,_ c::::, ___ Distance 1: This setting corresponds
to a distance of 92 feet/28 meters when travel­
i ng at 62 mph (100 km/h), or a tim e interval of 1
second .
c::::, __ c::::, __ Distance 2: This setting corresponds
to a distance of 118 feet/36 meters when travel­
i ng at 62 mph (100 km/h), or a time interval of
1.3 seconds . ..,.
113

a,
a,
..... N r-­N ..... 0 0
0:
co
Audi adaptive cruise control and braking guard
Audi braking guard
Description
Applies to: ve hicles with Audi adaptive cruise co ntro l
Fig. 132 Instrument cluste r: approach warning
Braking guard uses a radar sensor. It also func­
tions within the limits of the system when adap­
tive cruise control is switched off .
What can braking guard do?
When detected in time, the system can assess
situations when a vehicle ahead brakes suddenly
or if your own vehicle is traveling at a high speed
and approaching a vehicle up ahead that is mov­
ing more slowly . Braking guard does not react if
it cannot detect the situat ion.
The system advises you of various situations:
- The
distance warning is g iven if you are too
close to the vehicle ahead for a long time.
If the
vehicle ahead brakes sharply, you will not be
able to avoid a collision. The indicator light .
in the display comes on.
- The
approach warning is given when a detected
vehicle up ahead in your lane is moving much
more slowly than you are or if it brakes sharply .
When this warning is g iven, it may only be pos­
s ible to avo id a col lision by swerving or brak ing
sharp ly. Th e indicator light . will warn you
about the danger
¢fig. 132. You will also hear
an acoustic signal.
If you do not react fast enough or do not react at
all to the situation, braking guard will intervene
by braking and the message
Braking guard: Acti­
vated
will appear.
1> Th is is not ava ilab le in some coun tries.
-If a collision is imminent, the system wi ll first
provide an
acute warning by briefly and sharply
apply ing the brakes.
- If you do not react to the acute warning, brak­
ing guard can brake within the limits of the sys­
tem. This reduces the vehicle speed in the event
of a collision.
- At speeds under 20 mph (30 km/h), the system
can initiate a comp lete decelerat ion shortly be­
fore a collision
ll.
- If the braking guard senses that you are not
braking hard enough when a collision is immi­
nent, it can increase the braking force .
Which functions can be controlled?
You can switch braking guard and the distance/
approach warn ing on or
off in the radio/MM!*
¢ page 116, Settings in the radio/MM!*.
A WARNING
-
Lack of attention can cause collisions, other
accidents and ser ious personal in juries. The
braking guard is an assist system and cannot
prevent a collision by itself. The driver must
always intervene. The driver is always respon­
sible for braking at the correct tim e.
- Always pay close attention to traffic, even
when the braking guard is switched on. Be
ready to intervene and be ready to take
comp lete control whenever necessary. Al­
ways keep the safe and legal distance be­
tween your vehicle and vehicles up ahead .
- Braking guard works wit hin limits and will
not respond outside the system limits, for
examp le when approaching a stopped veh i­
cle or stationary obstacle (end of a traffic
jam or vehicle that has broken down in traf­
fic).
- Always remember that the radar sensor for
the braking guard works only within defined
detection and range limits that may prevent
the proper detect ion of other vehicles.
- The radar sensor's function and range can
be reduced by rain, snow and heavy spray.
Moving vehicles up ahead may not be
,.
115

Audi adaptive cruise control and braking guard
promptly detected or may not be detected
at all.
- Reflective surfaces including crash barriers
or tunnel entrances may impair the function
oftheradarsensor.
(D Tips
-You can cancel the braking that is initiated
by the system by braking yourself, by accel­
erating noticeably or by swerving.
- Braking guard error messages
c:> page 116.
- Keep in mind that braking guard can brake
unexpectedly. Always secure any cargo or
objects that you are transporting to reduce
the risk of damage or injury.
Settings in the radio/MMI*
Applies to: vehicl es w ith Audi adaptive cruise control
.,. Select : ICARI function button> Audi braking
guard .
Or
.,. Select:
~I C~A~R~I function button > Car systems*
control button > Driver assist> Audi braking
guard .
System -
Switch braking guard On and Off. When
you switch the ignition on, the message
Braking
guard: Off
appears if the system is switched off .
Early warning -The distance and approach warn­
ings in the display can be switched
On/Off .
(D Tips
-Your settings are automatically stored and
assigned to the remote control key being
used at the times the settings are made
r=;,page 33.
-If you restrict the ESC, the braking guard al­
so switches itself off
c:> page 18 7.
- Switch braking guard
off when you are load­
ing the vehicle onto a vehicle carrier, train,
ship or other type of transportation . This
can prevent undesired warnings from the
braking guard system.
Messages
Applies to: vehicles w ith Audi adaptive cruise contro l
Braking guard: Off
116
This driver message appears if the system is
turned
off via the radio/MM I*. Otherwise, if the
system is turned
off, the information appears ev­
ery time shortly after the start of the trip.
The driver message also appears if the system is
not available due to a malfunction or if the ESC is
not switched on
c:> page 187. If this is the case,
the system will not provide warnings about a possible collision.
Braking guard: Activated
This driver message appears if sharp brake pres­
sure was applied due to an acute warning.
•••
Three white dots appear if a setting cannot be se­
lected with the operating lever . For example, this
happens if you want to raise/lower the speed
even though there was no previously saved
speed.
ACC: Sensor blocked
This message appears if the sensor view is ob­
structed, for example by leaves, snow, heavy
spray or dirt. Clean the sensor
r=;, page 109,
fig. 122 .
ACC: Unavailable
The driver message appears if, for example, the
brake temperature is too high. The adaptive
cruise control is temporarily unavailable. A chime
sounds as a rem inder.
ACC: Not available
The driver message appears if there is a malfunc­
tion. The adaptive cruise control turns off. A
chime sounds as a reminder. Have the system
checked by an authorized Audi dealer or author­
ized Audi Service Facility.
Shift lever position!
The driver message appears if the selector lever
is shifted to the N position. The adaptive cruise
control is not available while in this position.
Stabilization control (ESC)
This message appears if the Electronic Stabiliza­
tion Control (ESC) is taking action to stabilize the .,.

Audi side assist
Audi side assist
Side assist
Description
Applies to: veh icles with Audi side assist
F ig. 133 Sensor detection range
Fig . 1 34 D isp lay on the exterio r m irror
Side assist helps you monitor your bl ind spot and
traffic behind your vehicle. Within the limits of
the system , it warns you about vehicles that are
comi ng closer o r that are traveling with you with­
in sensor range
(D c:> fig. 133 . If a lane c hange is
cl assified as c ritic al, the displ ay @ in the exter io r
m irro r
c:> fig. 134 turns on .
The display in the left exter ior mir ro r provides as­
sis tance whe n making a la ne change to the left,
while the disp lay in the rig ht exte rio r mi rror pro­
vides assis tance when mak ing a lane chan ge to
the right .
Information stage
As long as you do no t activate the turn signal,
side assis t
informs you about ve hicles tha t are
detected and class if ied as crit ic al. T he disp lay in
the respe ctive m irror turns on, but is dim .
118
The display remains dim intentionally in the in­
formation stage so that your view toward the
front is not disturbed .
Warning stage
If you activate the turn signal, side assis t warns
you about vehicles that are detected and classi­
fied as crit ica l. T he disp lay in the respective mir­
ror blinks bright ly.
If this happens, check traffic
by glancing in the rearview mirror and over your
shou lder
c:> .&. in General information on
page 119 .
{!) Tips
-You can adjust the brightness of the disp lay
@ i=>pagel20.
-Please refe r to the instructions for towing a
trailer located in
i=>page 119.