ignition AUDI Q7 2018 Owner´s Manual

Assistance systems
The distances provided are specified values . De ­
pending on the driving situation and how the ve­
h icle ahead is dr iv ing, the actual d istance may be
more or less than these target d istances.
If you change the time gaps, the newly set value
appears briefly in the instrument cluster disp lay
II for Distance 3. T his only occurs if the Driver
assistance
display is not currently shown in the
d isplay
c::;, page 104, fig. 99.
Distance 1: this setting corresponds to a distance
of 92 ft (28 m) when traveling at 62 mph (100 km/h), or a time d istance of 1 second.
Distance 2 : this setting corresponds to a distance
of 118 ft (36 m) when traveling at 62 mph (100
km/h), or a time d istance of 1.3 seconds .
Distance 3: this setting corresponds to a distance
of 164 ft (SO m) when traveling at 62 mph (100
km/h), or a time distance of 1.8 seconds .
Distance 4: this setting corresponds to a distance
of 219 ft (67 m) when traveling at 62 mph (100
km/h), or a time dista nce o f 2.4 seconds .
Distance 5 : this setting corresponds to a distance
of 328 ft (100 m) when traveling at 62 mph (100
km/h), o r a time distance of 3.6 seco nds.
A WARNING
When setting the distance, the driver is re­
sponsible for adhering to any applicab le lega l
regulations.
(D Tips
Depending on the selected driving mode in
drive se lect* and the set distance, the driving
behavior will vary from dynamic to comforta­
ble when accelerating
c::;, page 129.
Setting Audi adaptive cruise control
App lies to: ve hicles w ith Aud i adapt ive cruise co ntro l
-
.. Se lect in the Infotainment system: I MENU I but­
ton
> Vehicle > left control button > Driver as­
sistance
> Audi adaptive cruise control.
1) In prepa ra tio n at the t ime of print ing. T his funct ion is not
ava ilable in every vehicle .
108
Storing the last distance1
)
The last distance that was set will be stored after
the ignition is switched off. If the distance is not
stored,
Distance 3 is a utomatica lly set eve ry time
the ignit ion is switched on.
(D Tips
Your settings are automatically stored and as­
signed to the remote control key being used.
Driver intervention request
Applies to : vehicles wi th Aud i adap tive c ru ise con trol
Fig. 104 Instrument cluster: request for driver interve n­
t ion
The reques t for driver in tervention inst ructs you
to take over if the adaptive cruise control braking
function is not able to maintain a suffic ient dis­
tance to the vehicle driving ahead
r:!> fig. 104.

Ass is tanc e system s
-when it is dark
- if the camera window or the windshie ld is
dirty, iced over, damaged or covered
- when driving on snow, ice or loose gro und
- i n cu rves
- if t he ESC was restr icted o r switched off
- when tow ing a tra ile r
- when the driver's seat belt is unfastened
- up to ten seconds after sw itching on the ig-
nition
@ Note
Impacts or damage to the camera mount on
the windshield can disp lace the sensor . Pre
sense city can be impa ired by this. Have an au­
thorized Audi dealer or authorized Aud i Serv­
ice Facility check the ir funct ion.
(D Tips
- You can cancel the system braking interven ­
tion if you accelerate considerably or swerve
away .
- Keep in m ind that pre sense city can brake
unexpected ly. Always secure any cargo or
objects that you are transport ing to reduce
the r isk of damage or injur y.
- Specific pre sense city funct ions sw itch off
when the ESC is limited o r switched off
~ page 143 or the hill desce nt assist is
switched on
~ page 144 .
-When there is a malfunct ion in the camera,
the pre sense city funct ions also sw itc h off.
Settings in the Infotainment system
Applies to: vehicles with Aud i pre sense
.,. Se lect in the Infota inment system: IMENU I but­
t on
> Vehicle > left contro l bu tton > Driv er a s­
si stance
> Audi pre s ense .
Turn on/ off Audi pre s ense -
the pre sense fu nc­
tions c an be t urned o n and off.
If t he system is switched off, it switches o n aga in
automatically once the ignition is sw itched on
again.
116
Prewarning -the early warning can be sw itched
off or the pre sense city/front warning point can
be set
( Early /Medium /Late) .
Set the warn ing t ime for the early wa rning to
Earl y at first . If this causes undesi red ear ly warn­
ings to appear, then set the warning time to
Me­
dium .
The Late warning time should on ly be set
i n spec ial circumstances, for examp le, when driv­
i ng with a very dynamic style.
(D Tips
Your settings are automatically stored and as ­
signed to the remote contro l key being used.
Messages
Applies to: vehicles with Audi pre sense
IIJ Audi pre se n se: mal function! Pl ease con tac t
Service
This message appears when the pre sense func­
tion is affected . For example, th is cou ld be
caused by a faulty sensor. Drive to an authorized
Audi dealer or author ized Audi Service Fac il ity im ­
med iate ly to have the ma lfu nction corrected .
II] Audi pre sense: currently limited . Sensor
v iew lim ited due to surroundings. See owner 's
manual
This message appears if the radar sensor and camera view is obstructed, for example by leaves,
snow, heavy spray or dirt . If necessary, clean the
sensors and the area around the camera
~ page 103, fig . 95 or ~page 121, fig . 115 .
II] Audi pre sense: currently limited . Trailer
towing mod e
For vehicles with a trai ler hitch installed at the
factory, the pre sense rear functions switc h off
when the electrical connector at the socket is
plugged in . There is no guarantee the functions
will switc h off when us ing a retrofitted trailer
hitc h.
II] Audi pre sense: currently restricted
This message appears if the ESC is restricted or
switched off, for example. .,,.

Ass is tance sy stem s
potential for hydroplaning . Using active lane
assist under these conditions may increase
the risk of a crash.
Switching on /off
A pp lies to: ve hicles w ith Audi active lane assist
F ig. 109 Turn signal lever: button for active lane ass ist
F ig .1 10 Windsh ie ld: camera window for act ive lane ass ist
.,.. Press the button to switch the system on and
off
c!;> fig. 109. The indicator light in the instru­
ment cluster turns on or off.
118
Analog lnstru- Audi virtual Meaning on
ment cluster cockpit /head- the corre-
up display* sponding side
Green Li ne(s) Green line(s) Active lane as-
(left/right) (left/r ight) sist is activat-
., -J ed and ready
to provide
warnings.
-Red line Active lane as-
(left/r ight) sist warns you
-J before leaving
a lane. In addi-
tion, the steer-
i ng whee l vi-
brates light ly.
Yellow line(s) Gray
li ne(s) Active lane as-
(left/right) (left/r ight) sist is activat-
·/ ed, but is not
r eady to g ive
warning
If the system is switched on but is not ready to
provide warnings, one of the following could be
the cause:
- There is no lane marker line .
- The relevant lane marker lines are not detected
(for example, markings in a construction zo ne
or because they are obstructed by snow, dirt,
wate r or light ing) .
- The vehicle speed is below the activation speed
of approximately 40 mph (65 km/h).
- The lane is too narrow or too wide .
- The curve is too narrow.
- The driver's hands are not on the steering
wheel.
(D Tips
- Make sure the camera window ¢fig . 110 is
not covered by stickers or other objects. For
information on cleaning, see
¢ page 351.
- In certain markets: if the system is switched
on, it will switch on automatically each time
the ignition is sw itched on.

a co ...... N r--. N ...... 0
0
:E ' Exit warning
Applies to: ve hicles with exit warning system
Fig . 116 Example dis play
Fig. 117 Door: warning str ip
When the vehicle is stationary, the exit warning
system warns the passengers of a possible colli ­
sion when opening the door . Within the limits of
the system, the system monitors the areas be­
hind and next to the vehicle using the radar sen­
sors
c::¢> page 121, fig. 115 . Moving objects that
are approaching from behind, such as cars, are
detected
c::¢> fig. 116.
When you open the door, the warning str ip on
the affected door blinks ¢
fig. 117 if another
r oad user is detected and the situation is classi­
f ied as critical. The display in the exterior mirror
on the affected side flashes at the same time . If
the door is already open and another road user is
detected and the situation is classified as critical,
then the corresponding displays turn on .
A WARNING
-Always pay attention to traffic and to the
area around your vehicle. The exit warning
system does not replace the attention of the
passengers. The vehicle passengers are al-
Assistance systems
ways responsible for opening the doors and
exiting the vehic le.
- The exit warning system can be available for
up to approximately three minutes after un­
locking the vehicle and opening the door as
well as after switching off the ignition . Then
the system switches off with a brief flashing
of the displays.
- The exit warning system cannot notify you
of every approaching object or person, such
as joggers or pedestrians .
A WARNING
The exit warning system is subject to limita­
tions and cannot warn you before every im­
pending coll is ion:
- If the veh icle is too wide for the parking
space and covered by the neighboring
veh icles.
- Approaching objects or peop le such as cy­
clists or skateboarders may not be detected
under certain circumstances.
- The system does not react to stat ionary ob­
jects.
- The view of the radar sensors may be im­
paired by leaves, snow, heavy spray or dirt .
Clean the area in front of the sensors
c::¢> page 121, fig. 115.
(D Note
Also read the information in c::¢,(D in General
information on page 122 .
(D Tips
-The exit warning system is switched on and
off through the side ass ist
c::¢> page 122. The
ex it warning indicators turn on dur ing the
adjustment process.
- The display brightness for the exit warning
system cannot be adjusted.
- T he system is not availab le when tow ing a
trailer.
-
123

Ass is tance sy stem s
Switching on/off
Applies to: vehicles with night vision assist
F ig. 125 Are a aro und th e light sw itc h: night vis ion assist
butto n
Requiremen t: sw itch the ignition on and turn the
light switch to the
AUTO position.
.. Press the~ button ~
fig. 125 . The heat image
from the nig ht vision camera appears in the in­
str ument cluster d isplay.
.. Press the~ button again to switch the night
vision assist off .
If condit ions are b right enough, night vision as­
sis t can be sw itched on withou t mov ing the light
switch to the
AUTO position. Pedestrian and wild
an imal highlighting and warnings are only active
when it is dark outside and the headlights are
sw itched on .
Adjusting the contrast
Applies to: vehicles with night vision assist
.. Select in the Infotainment system: IM ENU I but­
ton
> Vehicl e > left control button > Driver a s­
si stance
> Nig ht vis ion as sist contra st .
When the night vision assist is switched on and
the image is visible in the instrument cluster d is ­
p lay , you can adjust the contrast in the image
from
Min to Ma x.
Messages
App lies to: vehicles with night vision assist
• Night vi sion a ssist : malfunction! Plea se con ­
tact Ser vic e
The system cannot guarantee correct function
and is switched off. See a n author ized Audi deal-
128
er or authori zed Aud i Service Facility fo r assis ­
tance .
a Night vi sio n assi st: c urrently unav ail able .
See owner's manual
The system cannot guarantee correct funct ion at
th is time and is switched off .
a Night vision ass ist: currently un av ailabl e.
Plea se turn on the lights
Night vision assist only works when it is dark out­
side and the headlights are on.
a Night vision ass ist: pedestr ian h ighlighting
curr ent ly unavailable. See owne r's manual
The pedestrian and wi ld animal marki ng was
switched off by the system .
Audi drive select
Introduction
App lies to: vehicles with Aud i drive se lect
Drive select makes it possible to exper ience dif­
ferent types of vehicle sett ings in one veh icle .
You can select the d riving modes
Offroad * or
Lift / Offroad *, Allroad *, Comfort , Auto and Dy ­
namic
in the Infota inment system, for example
to switch from a sporty to a comfo rtable driving
mode. In the
I ndividual mode, the settings can
be adjusted to your personal preferences. This
makes it possible to combine sett ings such as a
sporty engine setting with light steer ing .
Description
Applies to: vehicles with Audi drive select
The following systems, among other th ings, are
i nfluenced by dr ive se lec t:
Engine and automatic tran smis sion
Depend ing on the mode, the engine and auto ­
matic transmission respond more quickly or in a
more balanced manner to accelerator pedal
movements . In the sporty
Dynam ic mode, the
transm iss ion shifts at higher speed ranges .

a co .... N r--. N .... 0
0
:E ' CD Note
The lift/ Offroad mode switches to Allroad
mode when dr iving above approximately
20 mph (30 km/h) and the veh icle automati­
cally lowers again. These modes may only be
used on a temporary bas is and are not intend­
ed for continuous d riving.
(D Tips
- The filled-in boxes in the Infotainment sys­
tem represent the current vehicle level. If
the box is wh ite or the boxes are blinking,
the veh icle is lift ing or lowe ring. If on ly the
bottom box is fi lled in, the vehicle is at the
l owest level ( le a st amount of g round clear ­
ance) . If all the segme nts are fi lled in, then
the vehicle is at the highest level (highest
ground clear a nee) .
- The target level is hig hligh ted wi th a
red
frame while the vehicle is lifting o r lower­
i ng. The frame is then hidden when the ve­
hicle reaches the target level.
- The vehicle lifts up to the highest level
when you se lect
lift / Offroad . Select an ­
other mode to lower the vehicle again.
Rear lowering
App lies to: vehicl es with air suspe nsio n
The rear of the vehicle con be lowered to make
loading and unloading easier .
Fig . 12 7 Sect ion of l uggage co mpa rt m ent: rear lower ing
b ut ton
Req uirement: a ll vehicle doors must be closed .
" Open the l uggage compa rtment lid .
" Press the lower section of the button
¢fig . 127 @. The rear of the veh icle lowers .
Assi st a nce systems
" Press the upper section of the butto n (D. The
rear of the vehicle raises again.
T he rear lower ing a utomat ica lly deac tiva tes
when you select another mode or when the vehi ­
cle speed exceeds approximately 2 mph (2 km/
h).
T he L ED in the button t urns on while the ve hicl e
is lowering . When the loading level has been
reached, the LE D stays on as long as the rear of
t h e vehicle is lowered . The LED turns off when
the vehicle returns to the original level.
CD Note
- Before the rea r lowering e nds, make sure
there is enough clearance above the vehicle
and the l uggage compartment lid, if it is
open.
- Do not park the vehicle in a lowered load ing
level.
(D Tips
- The ve hicle w ill not lowe r if one of the vehi­
cle doors is open
or when the ignition is
switched off and the compressed air reser­
voir is empty . The butto n LED bli nks three
times .
- If the compressed air reservoir is empty, it
is refilled while driving at speeds above
25 mph (40 km/h).
Messages
Applies to: vehicles with air suspension
rl A ir s uspension: vehicle current ly too h igh.
Controlling level. ..
rl Air suspension: vehicle currently too low.
Controlling level. ..
The message turns off when t he leve l cont rol
process is complete .
131

Multi Media Interface
-Switching off manually : press and hold the
On/Off knob@¢
fig. 150 until the MMI
switches off . If the M MI has been sw itched off
manually, it does
not switch on again automati­
ca lly the next time the ignition is switched on.
Additional functions:
- Adjusting the volume:
turn the On/Off knob (D
¢fig . 150 .
-Muting : press the On/Off knob (D ¢ fig. 150
briefly.
-Selecting the previous/next function (for ex­
ample, a radio station/track):
press the On/Off
knob
(D ¢ fig . 150 briefly toward the left l rightl>t>f .
-Fast forwarding/rewinding (for example
songs) :
press and hold the On/Off knob (D
¢ fig. 150 toward the left lt>f .
.8. WARNING
Adjust the volume of the audio system so that
signals from outside the vehicle, such as po­
lice and fire sirens, can be heard easily at all
times.
(D Tips
The MMI switch es off automatically if the en­
gine is not r unning and the vehicle battery is
low.
Infotainment system
display
Switching on/off
" Press the to l button to switch the Info tainment
system on and off.
When the MMI is switched on and the display is
switched off, you can operate ce rtain funct ions
using the On/Off knob with the MMI joystick
function
¢ page 149.
(D Tips
There may be delays when switching on the
display.
150
Information on display images
The display version depends on vehicle equip­
ment.
Fig. 151 Disp lay ve rs ion A
Fig. 15 2 Disp lay ve rs ion B
Additional content (such as album cover and map
material) is shown on display version B, if appli­
cable
(D ¢ fig. 152. Because the other content
shown on the displays is nearly identical between
the two vers ions, this manual will primarily de­
scribe display version A.

Cl a:, ...... N
" N ...... 0
0
::r ' Voice recognition system Operating
Applies to: vehicles with voice recognitio n system
You con operate many Infotainment functions
conveniently by speaking.
Requirement: the ignition and the MM I must be
switched on ¢
page 149, there must not be any
phone call in progress and the park ing system
must not be active .
~ Switching on: briefly press th e ~ button @
¢page 15, fig. 11 on the m ultifunction steer ­
ing whee l and say the desired command after
the
Beep .
~ Switching off : press and hold the~ button.
Or: press the [2] butto n.
~ Pausing : say the command Pause . To resume,
press the~ button .
~ Correcting : say the com mand Correction . Or :
simp ly say a new command du ring an an ­
no uncement
¢ page 245.
Input assistance
The system gu ides you throug h the input with
v isua l and audio feedbac k.
- Visual input assistance : after switching on
vo ice recogn it ion, a display w ith a selection of
poss ible commands appea rs . This command
display can be sw itched on o r off . Se lect:
IMENU I button> Se ttings > left cont rol button
> MMI settings > Speech dialog system .
- Audio input a ssis tance :
to have the poss ible
comma nds read, tu rn t he voice recogn ition sys ­
tem o n an d say
Help.
For the system to understand you:
Speak clearly and dis tinct ly at a normal vo lume .
Speak lo uder when d riving faste r.
Emphasize the words in the commands even ly
a n d do not leave long pauses .
C lose the doors, the windows and the sunroof* to
reduce background noise . Make su re that passen­
gers are not speaking when you are giving a voice
command .
Voice recognition system
Do not d irect the vents towa rd the hands -free mi ­
c ro p hone, which is in the roof head liner nea r the
front interior lig hts.
Only use the system from the dr ive r's seat be ­
ca use the hands -free microphone is di rected to ­
ward that seat .
Additional settings
See¢ page 245, Spee ch dialog system .
_&. WARNING
- Dir e ct y our full atte nti on to dr iv ing. As the
d river, you have com plete re sponsibility fo r
safety in traff ic . O nly use the functions in
such a way t hat you a lways maintai n com ­
p lete contro l over your vehicle in all traffic
situations.
- Do not use t he voice recognition system in
emergencies beca use your voice may change
in stressfu l situations. It may take longe r to
d ia l the number o r th e system may not be
ab le to d ia l it at all. Dia l the emergency
number manually.
(D Tips
-The d ialog pauses w hen the re is a n incom­
ing phone call a nd will cont inue if yo u ig­
nore the call. The d ia log ends if yo u answer
t he ca ll.
- Yo u can select an item in the list us ing ei­
t her the vo ice recogn it io n sys tem o r the
cont ro l knob .
Command overview
information
Applies to: vehicles with voice recognition system
T he following overv iews des cribe the comm ands
t h at can be used to ope rate the MMI using the
vo ice recognit ion system.
Alte rnative comm ands ar e separate d using a"/",
f o r ex ample say:
Telephone / (or) Navigation /
(or) Radio.
Sequences of commands used to perfo rm an ac­
t io n a re iden tified w it h a "> ", fo r ex am ple s ay:
Enter address > ( then) Enter country/state . ..,
167

Cl a:, ...... N
" N ...... 0
0
::r ' The ignition and the MMI must be switched on.
No phone call is in progress.
T he parking aid as well as the Audi voice recogni­
tion system must not be active .
A cell phone must be connected to the MMI with
the
Handsfree profile ¢ page 174.
The cell phone being connected must have voice
control that can be controlled externally .
.. Switching on: press and hold the 5) button on
the multifunction steering wheel* and say the
desired command after the external speech di­
alog begins .
.. Continuing/resuming the dialog: the system
remains ready to use for a short time after end­
ing the dialog. You can start a new external dia­
log during this time . Press the
51 button if
needed, and say a new command .
Or: select
and confirm
Resume on the MMI control panel.
.,. Switching off: press and hold the 5) button .
Or: select and confirm Cancel on the MMI con­
trol panel.
(D Tips
- There are no voice guidance* prompts when
a dialog is active.
- This function depends on the cell phone
used. You can obtain more information
from your cell phone service provider or
from your cell phone user guide.
- AUDI AG simply provides access to control
your cell phone with voice operation and
does not take any responsibility for the con­
tents and commands within the external
voice control.
Voice recognition system
173

Tele phone
Telephone
Introduction
Applies to: vehicles with telephone
To make phone coils in your vehicle using the
/11/111, connect your cell phone to the /11/111 via
Bluetooth.
Hand sfree
After you have connected your ce ll phone to the
MMI via Bluetooth, you can use the handsfree
system and operate telephone functions through
your MMI. You can make calls using the antenna
on your cell phone.
A WARNING
- Medical experts warn that cell phones can
interfere w ith the funct ion of pacemakers .
Always mainta in a m inimum d istance of
about 8 inches (20 cm) between the ce ll
phone antenna and the pacemaker.
- Do not carry the cell phone in a pocket di ­
rectly over the pacemaker when the phone
is switched on.
- Sw itch the cell phone off immediately if
you suspect it may be interfering w ith the
pacemaker.
- Do not use the vo ice recognit ion system*
<=) page 167 in emergencies because your
vo ice may change in stressful situations. It
may take longer to dial the number or the
system may not be able to dia l it at all. Dial
the emergency n umbe r manua lly.
- Switch your cell phone off in areas where
there is a ris k of an exp losion . These loca­
tions are not always clearly mar ked. This
may include gas stations, fuel and chemical
storage facilities or transport vehicles, o r lo ­
cations where fue l vapors (such as propane
or gaso line vapor in vehicles or bui ldings),
chemicals or large quantities of dust parti ­
cles (such as flour, sawdust or metal) may
be present in the air . This also applies to all
other locations where you would normally
turn your vehicle engine off .
- The demands of traffic requ ire your full at­
tent io n. Always read the chapter
Q page 149, Traffic safety information.
174
-
@ Note
Always fo llow the information found in Q @ in
Wi -Fi hotspot on page 194.
(D Tips
- Th e Bluetooth connect ion range is limited
to inside the vehicle. It can also be affected by local conditions and interference with
other devices .
- To learn which Bluetooth connections and
wh ich of the funct ions in your ce ll phone are
supported, check with your cell phone serv­
ice provider or the database for mob ile devi­
ces at www .aud iusa .com/bluetooth.
Setup
Connecting a cell phone using Bluetooth
Applies to: vehicles with telephone
Fig . 172 D isp layin g the PIN for enter ing in t he cell phone
R equi rem ent
The vehicle must be stationary and the ignition
must be switched on.
The Bl uetooth settings m ust be open on your cell
phone during the connection setup.
The Bluetooth funct io n and v is ib il ity of the MMI
Q page 248 and cell phone must be sw itched on.
The cell phone to be connected must not be con­ nected to any other Bluetooth device .
The MMI must not be connected to a cell phone.
Conn ecting a c ell phon e
.. Select: IMENU I button> Telephone > Connect
mobile de vice > Find new de vic es > Next.
The
avai lab le Bluetooth devices are shown in the In-
fotainment system display.
Or select: ! MENUI 1111-