ignition AUDI RS5 CABRIOLET 2015 Repair Manual

160 Child Safety
belts, ¢page 131, Airbag system and
c:> page 152, Important things to know.
A WARNING
If exceptional circumstances require the
use of a forwa rd-facing child restraint on
the front passenger's seat, the child's safe­
ty and well-being require that the follow­ ing special precautions be taken:
- Make sure the forward-facing seat has
been designed and certified by its manu­
facturer for use on a front seat with a
passenger front and side airbag.
-Always follow the manufacturer's in­
structions provided with the child safety
seat or infant carrier.
- Always move the front passenger seat in­
to the rearmost position of the passen­
ger seat's fore and aft adjustment range,
and as far away from the airbag as possi­
ble before installing the child restraint.
- Always make sure that nothing prevents
the front passenger's seat from being
moved to the rearmost position in its
fore and aft adjustment range.
- Always make sure the backrest is in an
upright position.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched on.
- If the light does not stay on, perform the
checks¢
page 141, Monitoring the Ad·
vanced Airbag System.
- Take the child restraint off the front pas­
senger seat and install it properly at one
of the rear seat positions if the
PASSEN­
GER AIR BAG OFF
light does not stay on
whenever the ignition is switched on.
Booster seats and safety belts
Properly used booster seats can help protect
children weighing between about 40 lbs. and
80 lbs . (18 kg and 36 kg) who are
less than 4
ft. 9 in. (57 inches/1.45 meters) tall.
Fig. 161 Rear seat : chil d p roperly rest rai ned in a boos ­
ter seat
The vehicle's safety belts alone will not fit most children until they are at least 4
ft. 9 in .
(57 inches/1.45 meters) tall and weigh about
80 lbs.
(36 kg). Booster seats raise these chil­
dren up so that the safety belt will pass prop­
erly over the stronger parts of their bodies
and the safety belt can help protect them in a
crash.
.. Do not use the convertible locking retractor
when using the vehicle's safety belt to re­ strain a child on a booster seat.
.. The shoulder belt must lie as close to the
center of the ch ild's collar bone as possible
and must lie flat and snug on the upper
body.
It must never lie across the throat or
neck . The lap belt must lie across the pelvis
and never across the stomach or abdomen .
Make sure the belt lies flat and snug. Pull on
the belt to tighten if necessary .
.. Secure unused safety belts on the rear seat
c:>page 157.
Children up to about 40 lbs. (18 kg) are best
protected in child safety seats designed for
their age and weight. Experts say that the
skeletal structure, particularly the pelvis, of
these children is not fully developed, and they
must not use the vehicle safety belts without
a suitable child restraint.
...

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
It is usually best to put these children in ap­propriate booster seats. Be sure the booster
seat meets all applicable safety standards.
Booster seats raise the seating position of the
child and reposition both the lap and shoulder
parts of the safety belt so that they pass
across the child 's body in the right places. The
routing of the belt over the child's body is very
important for the child's protection, whether
or not a booster seat is used . Children age 12
and under must always ride in the rear seat.
Children who are at least 4
ft. 9 in. (57 in­
ches/1.45 meters) tall can generally use the
vehicle's three point lap and shoulder belts .
Never use the lap belt portion of the vehicle's
safety belt alone to restrain any child, regard­ less of how big the child is. Always remember
that children do not have the pronounced pel­
vic structure required for the proper function
of lap belt portion of the vehicle's three point
lap and shoulder belts. The child's safety ab­
solutely requires that a lap belt portion of the
safety belt be fastened snugly and as low as
possible around the pelvis. Never let the lap
belt portion of the safety belt pass over the
child's stomach or abdomen.
In a crash, airbags must inflate within a blink
of an eye and with considerable force. In order
to do its job, the airbag needs room to inflate
so that it will be there to protect the occupant
as the occupant moves forward into the air­ bag.
A vehicle occupant who is out of position and
too close to the airbag gets in the way of an
inflating airbag. When an occupant is too
close, he or she will be struck violently and
will receive serious or possibly even fatal in­
jury.
In order for the airbag to offer protection, it is
important that all vehicle occupants, especial­
ly any children, who must be in the front seat
because of exceptional circumstances, be
properly restrained and as far away from the
airbag as possible. By keeping room between
the child's body and the front of the passen­
ger compartment, the airbag can inflate com-
Child Safety 161
pletely and provide supplemental protection
in certain frontal collisions.
A WARNING
Not using a booster seat, using the boos­
ter seat improperly, incorrectly installing a
booster seat or using the vehicle safety
belt improperly increases the risk of seri­
ous personal injury and death in a collision
or other emergency situation. To help re­
duce the risk of serious personal injury
and/or death:
- The shoulder belt must lie as close to the
center of the child's collar bone as possi­ ble and must lie flat and snug on the up­
per body. It must never lie across the
throat or neck. The lap belt must lie
across the pelvis and never across the
stomach or abdomen. Make sure the belt lies flat and snug. Pull on the belt to
tighten if necessary .
- Failure to properly route safety belts
over a child's body will cause severe inju­
ries in an accident or other emergency
situation
~page 123.
- The rear side of the child safety seat
should be positioned as close as possible
to the backrest on the vehicle seat .
- Children on the front seat of any car, even with Advanced Airbags, can be seri­
ously injured or even killed when an air­
bag inflates .
- Never let a child stand or kneel on any
seat .
- Never let a child ride in the cargo area of
your vehicle.
- Always remember that a child leaning
forward, sitting sideways or out of posi­
tion in any way during an accident can be
struck by a deploying airbag. This will re­
sult in serious personal injury or death .
- If you must install a booster seat on the
front passenger seat because of excep­
tional circumstances the
PASSENGER
AIR BAG OFF
light must come on and
stay on, whenever the ignition is switch­
ed on. •
•
-

162 Child Saf ety
- If the PASS ENGER AIR BAG O FF li ght
does not come on and stay on, perform
the checks described
c:> page 141, Moni­
toring the Advanced Airbag System .
-Take the child restraint off the front pas­
senger seat and install it properly at one
of the rear seat positions if the
PASSEN­
GER AIR BAG OFF
light does not stay on
whenever the ignition is switched on.
- Always read and heed all WARNINGS whenever using a child rest rained in ave­
hicle is being used
c:> page 123, Safety
belts,
c:> page 131, Airbag sy st em and
c:> page 15 2, Important things to know.
Installing a child safety
seat
Securing a child safety seat using a
safety belt
Safety belts for the rear seats and the front
pas senger 's seat can be locked with the con­
vertible locking retractor to properly secure
child safety seats.
The safe ty belts eme rgency lock ing re tractors
fo r the re ar seats safe ty belts and for the
fro nt passenger's seat safety belt have a con­
vertible locking retracto r fo r child restraints.
The safety belt must be locked so that belt
webbing cannot unree l. The retractor can be
activated to lock the safety be lt and prevent
the safety belt webbing from loosening up
during normal driving . A child safety seat can
only be properly installed when the safety belt
i s locked so that the child and child safety
seat will stay in place.
A lways remember: Even thoug h your veh icle is
eq uipped w it h an Advanced A irbag system, all
ch ildren , espec ia lly those 12 yea rs and yo ung­
e r, should always ride in the ba ck seat proper­
l y res traine d for thei r age and weig ht.
_& WARNING
Imprope rly insta lled child sa fe ty seats in ­
crease the risk of ser ious personal inju ry
and death in a collision. -
Always make sure that the safety belt re­
tractor is locked when insta lling a child
safety seat. An unlocked safety belt re­
tractor cannot hold the child safety seat in place dur ing no rma l dr iving o r in a
crash .
- Always buckle the child safety seat firmly in place even if a ch ild is not sitt ing in it .
A loose child safety seat can fly aroun d
du ring a s udden sto p or in a colli sion.
- I f the backrest is not securely la tched,
the child and the child restraint will be
throw n forward toge ther with t he ba ck­
rest and will strike par ts of the vehicle
interior. The child can be se riously in ­
jured or killed.
- Never inst all rearward-facing child safety
seats or infant ca rr iers on the front pas­
senger seat . A child will be serious ly in­
jured and can be killed when the passen­
ger airbag i nflates.
- The inflating airbag will h it the ch ild
safety seat or infant carrier with great
force and will smash the child safety seat
and child aga inst the back rest , center
armrest, doo r or roof.
- Always install rearward-facing ch ild safe­
ty seats or infa nt carriers on the rea r
seat .
- Forwa rd-facing child safety seats or in­
fant car riers installed on the front pas­
senger's seat may interfere with t he de­
p loyment of t he a irbag and cause serious
i njur y to the child .
-It is safer to ins tall a forward-facing
child safety seat on the rear seat.
- Always read and heed all WAR NIN GS
whe neve r using a child restrai ned in ave­
h icle i s being u sed
c:> page 152. Special
p reca utions apply when ins tal ling a child
safety seat on the fron t passenger seat
c:> page 132, Child restraints on the front
seat -some important things to know.
_& WARNING
--
Always take specia l precautions if you
must install a forwa rd or rearward-facing

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
child restraint on the front passenger's
seat in exceptional situations:
- Whenever a forward or rearward-facing
child restraint is installed on the front
passenger seat, the
PASSENGER AIR
BAG OFF
light must come on and stay on
whenever the ignition is switched on .
-If the PASSENGER AIR BAG OFF light
does not come on and stay on, perform
the checks described
~ page 141, Moni­
toring the Advanced Airbag System .
- Take the child restraint off the front pas­
senger seat and install it properly at one
of the rear seat positions if the
PASSEN·
GER AIR BAG OFF
light does not stay on
whenever the ignition is switched on.
- Improper installation of child restraints
can reduce their effectiveness or even
prevent them from providing any protec­
tion.
- An improperly installed child restraint
can interfere with the airbag as it de­
ploys and seriously injure or even kill the
<;hild.
- Always carefully follow the manufactur­
er's instructions provided with the child
safety seat or carrier.
- Never place additional items on the seat
that can increase the total weight regis­
tered by the weight-sensing mat and can cause injury in a crash.
_&. WARNING
Forward-facing child restraints:
- Always make sure the forward-facing
seat has been designed and certified by
its manufacturer for use on a front seat
with a passenger front and side airbag.
- Never put the forward-facing child re·
straint up, against or very near the in­
strument panel.
- Always move the passenger seat into its
rearmost position in the seat's fore and
aft adjustment range, as far away from
the airbag as possible before installing
the forward-facing child restraint. The
Child Safety 163
backrest must be adjusted to an upright
position.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched
on .
_&. WARNING
"' Rearward-facing child restraints:
-A child in a rearward-facing child safety
seat installed on the front passenger
seat will be seriously injured and can be
killed if the front airbag inflates - even
with an Advanced Airbag System .
- The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat
and child against the backrest, center
armrest, door or roof.
-Always be especially careful if you must
install a rearward facing child safety seat
on the front passenger seat in exception­
al circumstances.
-A tight tether strap on a rearward-facing
child restraint attached to the front pas­
senger seat can put too much pressure
on the weight-mat in the seat and regis­
ter a heavier weight in the Advanced Air­ bag System. The heavier weight regis­
tered can make the system work as
though an adult were on the seat and de­
ploy the Advanced Airbag when it must
be suppressed causing serious or even
fatal injury to the child.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched
on.
- If the PASSENGER AIR BAG OFF light
does not come on and stay on, immedi­
ately install the rearward-facing child
safety seat in a rear seating position and
have the airbag system inspected by your
authorized Audi dealer. •
•

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
capacity is limited by tire traction. You
should therefore not drive at excessive
speeds on icy or slippery road surfaces.
- On wet road surfaces, be careful not to
dr ive too fast because the front wheels
cou ld beg in to slide on top of the water
(aquaplaning) . If this should occur, you
will have no warning from a sudden in­
crease in engine speed as with a front·
wheel drive vehicle . A lways d rive at
speeds wh ich are suited to the road con­
ditions -risk of crash.
Energy management
Starting ability is optimized
Energy management controls the distribution
of electrical energy and thus optimi zes the
availabili ty of electrical energy for s tarting
the engine .
If a vehicle with a conventional energy system
is not driven for a long period of time, the bat­
tery is discharged by idling current consumers
(e .g . immobilizer) . In certain c ircumstances it
can result in there being insufficient energy
avai lab le to start the engine.
Intell igent energy management in your vehi­
cle hand les the d istribution of electrical ener ·
gy. Starting ab il ity is markedly improved and
the life of the battery is extended .
Basically, energy management consists of
battery diagno sis, idling current manag e­
m ent
and dynamic en erg y manag ement.
B attery diagnosi s
Battery diagnosis continuously determines
the state of the battery. Sensors determ ine
battery vo ltage, battery current and battery
temperature . This determ ines the current
state of charge and the powe r of the battery.
Idling current management
Idling current management reduces energy
consumption while the vehicle is s tand ing.
W ith the ignition switched off, it contro ls the
energy supply to the various electr ica l compo·
Int ellig ent technolog y 177
nents . Data from batte ry diagnos is is cons id ­
ered.
Depend ing o n the ba ttery's state of cha rge ,
individ ua l cons umers are g radually turned off
to prevent excessive discharge of the battery
and t hus maintain sta rting capability.
Dynamic energy management
While t he vehi cle is being d riven, dynamic e n­
ergy ma nagement dis trib utes the energy ge n­
era ted accord ing to the needs of the individ u­
al components. It regulates consumption, so
that more e lectrical energy is not bei ng used
than is being generated and ensures an opti­
mal state of charge for t he battery.
(D Tips
- But even ene rgy management cannot
negate the limits of physics. Consider
that the power and life of a battery are
limited.
- If start ing ability is threatened, the indi­
cator light (•) ::ippears
¢ page 16.
What you should know
The highest priority is given to maintaining
star ting capability.
The battery is severe ly taxed in short-distance
driving, in city traff ic and during the cold time
of year. Ab undant electrica l energy is re­
quired, but on ly a little is generated . It is also
critical if the engi ne is not running and electri­
ca l components are turned on . In this in ­
stance ene rgy is be ing consumed but none is
being ge nerated .
It is in precisely these situations that you will
notice energy management active ly regu lat ·
ing the d istribut ion of energy .
Vehicle stands for an extended period
If you do not drive your vehicle over a period
of several days or weeks, e lectr ica l compo­
nents are gradually cut back or switched off.
This reduces energy consumption and ma in·
ta ins start ing capability over a longer period .
Some of the convenience func tions may not .,.
•
•

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
(D Note
-Be aware that just one tank fi lling with
le ad ed fuel will already seriously de­
grade the performance of the catalytic
converter.
- Do not exceed the correct engine oil leve l
c>page 199.
-Do not drive until the fuel tank becomes
complete ly empty. The engine could mis ­
fire. Unburned fuel could also get into
the exhaust system and this could cause
the catalyt ic converter to overheat.
- Do not turn off the ignition while the ve­
hicle is moving .
- Do not continue to operate your vehicle
under these condit ions, as otherwise fuel
can reach the catalytic converter. This
could result in overheat ing of the con­
verter, requ iring its replacement.
- To assure efficient operat ion of the Emis­
s ion Control System:
- Have your vehicle maintained properly
and in accordance with the service rec­
ommendations in your Warranty
&
Ma intenance booklet.
- Lack of proper maintenance as well as
improper use of the vehicle will impa ir
the funct ion of the emission control
system and could lead to damage .
@) For the sake of the environment
Even when the Emission Control System is
operating properly, the exhaust gas can
have a sulfur-like exhaust gas smell under
some operating states. This depends on
the s ulfur content of the fuel being used.
Using a d ifferent brand of fuel may help,
or filling the tank w ith lead-free super
grade gasoline .
Shutting down vehicle
If you would like your veh icle to remain inop­
erat ive for a longer period of time, contact an
Audi or other specialized dealer. They can ad­
vise you on necessary precautions e .g. corro ­
sion prevention, maintenance and storage.
Dri vin g and en vironm ent 181
Pay attention to additional information con ­
cerning the battery . Refer to
c> page 205 .
Operate your vehicle
economically and
minimize pollution
General
Your personal style of driving will determine
the economy of your vehicle, as well as ex ­
haust and noise levels.
Fuel economy, environmenta l impact, and
wear on your engine, brakes and tires largely depend on three factors:
- your personal d riving style
- operating conditions
- technical limitat ions
If you ant ic ipate what you need to do next and
drive economically, you can easily cut your
fuel consumpt ion by 10-15 percent . This sec­
tion w ill give you some tips on how you can
help the env ironment and your pocketbook.
(D Tips
The consumption estimates as published
by ENVIRONMENTAL PROTEC TION AGENCY
( E PA) and Transpo rt Canada may not cor re­
spond to your actual consump tion on the
road, which will vary depending upon vehi­
cle load and speed, road and weather con ­
dit ions, trip length, etc.
Drive smoothly and keep a lookout
ahead
Vehicles use the most fuel when they are ac­
celerating.
.,. Avoid unnecessary accelerating and braking.
Vehicles use the most f uel when they a re ac­
ce lerat ing. If you ant icipate what is going to
happe n next, you will need to brake less and,
th us, acce lerate less . Let the vehicle coast
whenever possible -for examp le when you see
that the next traff ic light is red.
•
•

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
Vehicl e ca re a nd cl eanin g 18 5
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft mi­
crofiber cloth.
Rinse the vehicle tho roughly again and let it
air dry. Remove any water residue using a
shammy .
A WARNING
-Only wash the vehicle when the ignition
is off and follow the instructions from
the car wash operator to reduce the risk of accidents .
- To reduce the risk of cuts, protect your­
self from sharp metal components when
wash ing the underbody or the inside of
the wheel housings .
- After washing the vehicle, the braking ef­
fect may be delayed due to mo isture on
the brake rotors or ice in the winter. The
brakes must be dried first with a few
careful brake applicat ions.
- If you wash the vehicle in an automatic car wash, you must fold the exterior m ir­
rors in to reduce the r is k of damage to
the mirrors. Power folding exterior m ir­
rors* must only be folded in and out us­
i ng the power folding function. -
To prevent paint damage, do not wash
the vehicle in direct sunlight.
- T o reduce the r isk o f damage, do not
wash the power top with a pressure
washer.
- To reduce the risk of damage to the sur ­
face, do not use insect removing spong­
es, kitchen sponges or similar items.
- Matte finish painted vehicle compo­ nents:
- To reduce the risk of damage to the surface, do not use polishing agents or hard wax.
- Never use car wash cycles that apply
protective wax. It can destroy the
matte fin ish effect.
- Do not place any stickers or magnet ic
signs on vehicle parts painted w ith
matte fin ish paint. The paint cou ld be
damaged when the stickers o r magnets
are removed.
@ For the sake of the environment
Only wash the vehi cle in facilities spec ial ly
designed for that purpose. This will red uce
the risk of dirty water contaminated with
oil from entering the sewer system.
Cleaning and care information
When clean ing and caring for individua l vehi ­
cle components, refer to the fo llowing tab les.
The information contained there is simply rec­ ommendations . For questions or for compo- nents that are not listed, re
fer to an author­
ized Audi dea ler or qualified workshop . A lso
follow the information found in
Q & .
Cle anin g ext erio r
Component Situation Solution
Wipe r bl ade s
Dirty <=> page 5 7, Cleaning windshield wiper blades
Hea dli ght s/ Dir ty Soft sponge with a m
ild soap solutional
tail li ghts
S en so rs /
Dirty Sensors: soft cloth with a so lvent-free cleaning product
c a mera l ense s Camera lenses: soft cloth with an alcohol -free cleaning
solution
Snow/ice Hand brush/so
lvent-free de-icing spray
•
•

"' N
a: LL co
rl I.O
"' rl
"' rl
Checking and filling Engine hood
Releasing and opening the engine hood
The engine hood is released from inside the
vehicle .
Fig . 172 Dr iver's side footwell: eng ine hood release
lever
F ig . 173 Re lease lever un der the engine hood
Before opening the engine hood, make sure
that the windshield w ipers are flat against the
windshield. Otherwise, they could damage the
paint on the hood.
.. With the driver's door open, pu ll the lever
under the instrument panel in the direction
of the arrow
q fig. 172.
.. Raise the hood slightly q &.
.. Press the rocker switch under the hood up­
ward
c::> fig . 173 . This re leases the catch .
.,. Open the hood.
& WARNING
Hot engine coo lant can burn you.
- To redu ce the r isk of being burned, never
open the hood if yo u see or hear steam
or coolant escaping from the engine
compartment. Wait until no steam or
Checkin g and fillin g 195
coolant can be seen or heard before care­
fully opening the hood.
Closing the engine hood
.. Pull the hood down until the pressure from
the struts is reduced .
.. Let the hood
drop down and latch in place .
Do not try to push it shut; it may fail to en­
gage
q &, .
_&. WARNING
-
A hood that is not comple tely latched
could fly up and b lock your view while dr iv­
ing.
- When you close the engine hood, chec k it
to make sure the safety catch has p ro pe r­
ly engaged . The hood sho uld be flush
with the surrounding vehicle body parts .
-If you notice while driv ing that the hood
is not secured prope rly, stop at once and
close it.
Working in the engine compartment
Be especially careful whenever you work in the engine compartment .
Whenever yo u mu st p erform an y w or k in th e
eng in e compa rtment, for example checking
and filling differ ent fluid s, there i s a ri sk of
injury , burns and accidents. To prevent per­
sonal injury always obser ve the following
WARNINGS . The eng ine compa rtment of an y
v ehicle is a hazardous are a
q A.
_&. WARNING
To help avoid injury, before you check any­
thing under the hood:
- Turn off the engine.
- Remove the ignition key.
- Apply the parking brake .
- Move selector lever of automatic trans -
mission to "P" (Park).
- Always le t the engine cool down . Hot
components wi ll bur n skin on contact .

196 Checking and filling
-To reduce the risk of being burned, never
open the hood if you see or hear steam
or coolant escaping from the engine
compartment . Wait until no steam or
coolant can be seen or heard before care­
fully opening the hood .
- Keep children away from the engine com ­
partment .
- Never spill fluids on hot engine compo­
nents. They can cause a fire.
- Never touch the radiator fan. The auxili­
ary electric fan is temperature controlled
and can switch on suddenly.
- Never open the coolant reservoir cap
when the engine is still warm. The cool­
ant system is pressurized and hot cool­
ant could spray out.
- Protect your face, hands and arm from
steam or hot engine coolant by placing a
thick rag over the cap when you open the
coolant reservoir .
- Do not remove the engine cover under
any circumstances. This increases the
risk of burns.
- If work on the fuel system or the electri­
cal system is necessary:
- Always disconnect the battery.
- Never smoke or work near heaters or
open flames. Fluids in the engine com­ partment could start a fire.
- Keep an approved fire extinguisher im­
mediately available.
- To avoid electrical shock and personal in­
jury while the engine is running or being
started, never touch:
- Ignition cables
- Other components of the high voltage
electronic ignition system.
- If you must perform a check or repair
with the engine running:
- First, fully apply the parking brake,
move selector lever of automatic trans­
mission to "P" (Park). -
Always use extreme caution to prevent
clothing, jewelry, or long hair from get­
ting caught in the radiator fan, V-belts
or other moving parts, or from contact­ ing hot parts . Tie back hair before
starting, and do not wear clothing that
will hang or droop into the engine.
- Minimize exposure to emission and
chemical hazards~& .
A WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain
or emit chemicals known to the State of
California to cause cancer and birth de­
fects and reproductive harm. In addition,
certain fluids contained in vehicles and
certain products of component wear con­
tain or emit chemicals known to the
State of California to cause cancer and birth defects or other reproductive harm.
- Battery posts, terminals and related ac­
cessories contain lead and lead com·
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive harms . Wash hands after handling .
(I) Note
When adding fluids, always make sure that
they are poured into the proper container
or filler opening, otherwise serious dam ­
age to vehicle systems will occur.
@) For the sake of the environment
To detect leaks in time, inspect the vehicle
floor pan from underneath regularly. If
you see spots from oil or other vehicle flu­
ids, have your vehicle inspected by an au­
thorized Audi dealer.

"' N
a: LL co
rl I.O
"' rl
"' rl
-If you have the impression your engine
consumes excessive amounts of oi l, we
recommend that you consult an author­
ized Audi dealer to have the cause of
your concern properly diagnosed. Keep in mind that the accurate measurement of
oil consumption requires great care and may take some time. An authorized Audi
dealer has ins tructions about how to
measure oil consumpt ion accura tely.
Checking the engine oil level
F ig. 175 MMI Display: Oil leve l indicator
Read oil le vel
"' Park your vehicle so that it is horizonta lly
level.
"' Shut the engine off when it is at operating
temperature.
"' Switch only the ignition back on .
"' Wa it approx. two minutes.
"' Se lect: Funct ion button
I _C_A_R_I > Oil l e v e l. Or
"' Se lect: Funct ion button
I CARI > Car sy s-
tem s* control button > Servicing & check s >
Oil level.
"' Read the oil leve l in the MMI* Display
r:::> fig. 175. Add engine oi l if the bar of the
o il level indicator is near "min"
r:::> page 199
Depending on the way the vehicle is driven
and the operating conditions, oil consumption
can be up to 1 quart per 600 mi les (0.8 liter
per 1,000 km). Consumption may be higher
within the first 3,000 miles (5,000 km) .
(D Tips
The oil level indicator in the MMI* Disp lay
is only an information display . If the oil
level is too low, a min imum oil warning ap-
Checkin g and fillin g 199
pears in the instrument cl uster . Add oil
Q page 199. If the hood has been opened,
the current oil leve l is shown in the instr u­
ment cluster the next time the ignition is
switc hed on.
F ig . 17 6 En gin e compart ment: Cover on the oil filler
n eck
"' Before you check anything in the engine
compa rtment,
alwa ys read and h eed all
WARNINGS r::> .&. in Working in the engine
compartment on page 195.
"' Shu t the eng ine off.
"' Unscrew the cap
't::::r. to the engine oil filling
hole
¢ fig. 176, ¢page 197, fig. 174.
"'Carefully top off with 0 .5 quarts (0 .5 liters)
of the appropr iate oil
¢page 197.
"'Check the oil level again after two minutes
r:::> page 199, Checking the engine oil level.
"'Top off the o il aga in, if necessary .
"' Screw the cap back on the fi lling hole .
.&_ WARNING
-W hile topping off, the o il m ust n ot come
in contact with hot e ngine parts -fir e
hazard !
- Th e oi l filler cap mus t be p roperly se­
cured to prevent oil from being sp rayed
on the hot engine and exhaus t system
when the engine is runn ing -fire haza rd!
- If you r skin has come in contact wi th the
e ngine o il, you must subse quently
cleanse it thorough ly.
(D Note
- Check the oil leve l using the r adio or
M MI*. I f the message
Plea se reduce oil