AUDI S3 2010 Workshop Manual

Reactivating the system after battery
disconnection Reactivating the convenience close/open feature
If the vehicle battery is disconnected and then reconnected,
the automatic closing and opening function will not work until it is reactivated. To reactivate this feature, perform the
following steps:
Reactivating close/open feature
-Pull and hold the power window switch until the window
is completely closed.
- Release the switch .
- Pull the switch again for one second. The automatic
closing/opening is now reactivated. •
Panoramic sliding sunroof
Applies to veh icles: with pano ram ic slid ing sunroof
Description
The panoramic sliding sunroof is operated with the toggle switch
=> fig. 39 wh en the ignition in on .
The panoramic sliding sunroof can still be opened or closed for
about 10 minutes after the ignition has been switched off. However,
as soon as the driver's or passenger's door is opened, the switch for
the roof is inoperative. •
Con tro ls and eq uip­
ment
Opening and closing
Applies to veh icles: wit h pano ram ic sliding sunroof
Opening and closing panoramic sliding
sunroof
.... ........... ...... ....................... .
;;;;;;;;;; ;;;;;::: ::::· ::;:;;::;;;;;;;;;; ;;;;i
1·············~1
.............. . ............. . ............. . .............. . ............ ..
• •
Fig. 39 Section of the
roof liner Toggle switch
for the panoramic
sliding sunroof
The panoramic sliding sunroof is opened in two stages.
First, the roof lifts up and then it can be opened.
Lifting
- Tap the switch G) ~ fig. 39 briefly, and the roof lifts auto­
matically (pop-up position) .
Opening automatically (independent operation)
-Tap the switch G)~ fig. 39 briefly, and the roof moves to
the lift position .
- Tap the switch
G) briefly a second time, and the roof
moves to the low wind noise comfort position .
- Press the switch
G) until the roof is fully open. In this
position increased wind noise may occur.
Opening manually (manual operation)
- Press the switch G) ~ fig. 39, starting from the "lift posi -
tion" unt il the roof has reached the desired position.
~
Vehicle care I I Technical data

Opening and closing
Closing completely
-Press the switch 0 => page 49, fig. 39 until the roof is
completely closed => & .
Closing partially
- Press the switch 0 => page 49, fig. 39 until the roof has
reached the desired position => & . If the roof is almost
closed and you interrupt the operation, the roof opens
automatically to a minimum setting; this is the smallest
possible opening that can be set.
If you park your vehicle in the sun, we recommend that you close the
sun blind. You should especially make certain that the panoramic
sliding sunroof is closed when the sun blind is closed when parked
or if there is a sudden rain shower.
The sun blind has two positions : completely open or completely
closed. The sun blind is manually operated.
& WARNING
Never close the panoramic sliding sunroof carelessly or without
watching -there is a risk of personal injury . For this reason , always
remove the ignition key when leaving the vehicle.
[ i J Tips
• When you park your vehicle, we generally recommend closing
the panoramic sliding sunroof and the sun blind.
• When the vehicle is parked, a wet roof should be dried lightly
with a soft cloth
before it is opened so that water does not drip into
the interior.
• In an emergency, the panoramic sliding sunroof can be closed
manually =>
page 50, "Emergency mechanical closing for the
panoramic sliding sunroof".•
Applies to vehicles: with panoramic sliding sunroof
Comfort closing
The open roof can also be closed from the outside.
-Hold the key in the driver's door lock in the lock position
until the roof is closed=>& .
& WARNING
Never close the panoramic sliding sunroof carelessly or without
watching -there is a risk of personal injury. •
Emergency mechanical closing for
the panoramic sliding sunroof
App lies to vehicles: with panoramic sliding sunroo f
Uncovering the light unit
In an emergency, the panoramic sliding sunroof can be
closed manually. Removal of the light unit requires some
dexterity.
Fig. 40 Light unit in
the headliner :
removing the glass

Fig. 41 Light unit in
the headliner:
removing the switch
cover
Please switch off all lamps before removing the light unit
=:>& .The glass and the switch cover simply click into place
for insta llation. Be sure they are positioned correctly for
installation .
Removing the glass
-Take the screwdriver from the vehicle tool kit.
- Use the flat end of the reversible screwdriver blade.
- Insert the screwdriver carefully between the light unit
and the glass into the visible marks (arrows)=:>
page 50,
fig. 40.
- Pry the glass out carefully.
Removing the switch cover
-Push the flat blade of the screwdriver several times in
succession between the light unit and the switch cover at
different places on the left and right and carefully lift the
switch cover as you do this =:> fig. 41. On vehicles with
additional equipment you can allow the cover to hang by
the wire, otherwise place the loose cover to one side.
Con tro ls and eq uip­
ment
Opening and closing
& WARNING
Before working on the front light unit switch the integral lamps off
- otherwise you risk being burned. •
Applies to veh ic les : with panoramic sli d ing sunroof
Removing the light unit
Removing the light unit requires some dexterity.
1111111111111111111111111111111
Fig . 42 Light unit in
the headliner:
removing screws in the
light unit
Fig . 43 Removing the
light unit
Installation of the light unit follows the steps used in
removal, but in reverse order.
- Install the Phillips head blade in the screwdriver.
Vehicle care I I irechnical data

Opening and closing
- Turn the two screws in the light unit in a counter-clock­
wise direction to remove=>
page 51, fig. 42.
Pull the light unit out of the headliner by the front end
(arrow) =>
page 51, fig. 43.
Allow the light unit to hang by the wire. •
Applies to vehicles: w ith panoramic s liding sunroof
Closing the open sky roof manually
Fig. 44 Left end face of
the instrument panel:
fuse cover with hand
crank
Fig. 45 Light unit in
the headliner : crank for
emergency operation
You can close the panoram ic sliding sunroof using the hand
crank located on the inside of the fuse box cover.
- Install the flat blade in the screwdriver . - Use the screwdriver to remove the
fuse box cover
=> fig. 44.
- Remove the crank from the fuse box cover.
- Remove the blade from the screwdriver handle.
- Install the end of the screwdriver handle onto the short
side of the crank to help you turn it=> fig. 44
G).
- Push the long end of the crank@=> fig. 45 all the way
into the hexagonal hole@.
- Hold the crank down and turn it with the screwdriver
handle to close the roof.
- Install the light unit first and then the glass. For installa­
tion, reverse the removal sequence.
- Return the crank to its location in the fuse box cover
=> fig. 44 and install the cover.
- Have the problem corrected.
[ i ] Tips
• To turn the crank for emergency closing more easily, you should
use the screwdriver handle as an aid. First, remove the screw driver
from the handle, then push the handle onto the crank.
• The crank should be turned slowly; turning it quickly only
increases the effort required. •

Clear vision
Lights
Switching the headlights on and off ·'t!-·
"' ~ a'.. a,
"'
Fig. 46 In strument
pane l: lig ht switch
Fi g. 47 Instrument
pane l: Light swi tch
with dayti me running
ligh ts (DR L)
The light switch must not be overturned past the stops in
either direc tion.
Switching on automatic headlight control*
- Tur n the lig ht swi tch to AUTO* :::> fig. 46.
Con tro ls and eq uip­
ment
Clear vision
Switching on the side marker lights
- Tur n t he lig ht sw itch to ~oo~ .
Switching on the headlights and high beam
-Turn the light sw itch to ;:o.
P ush th e high b eam lev er fo rward t owards th e ins tru­
ment pan el
=:> page 57.
Switching off the lights
- Turn t he ligh t switch to 0.
The head lights on ly work when the ignition is switched on. While
sta rting the engine or whe n switching off the igniti on, the head ­
lights wil l go off and only the side marker lights wil l be on.
Daytime running lights (DRL ) (USA models )
The daytime running lights can be turned on or off using this func ­
t ion . If the f unc tion is ac tive, the dayt ime running lights a re tu rned
on automatically when the ignition is switched on.
The daytime runn ing lights are activated
only w hen the light switch
i s at the
AUTO* or DRL * positi on.
Daytime running lights (Canada models only )
The daytime running lights are activated only when the light switch
~ fig. 46 is either at the O or the ;oo: position. When the ignition is
switched on, there is a difference betwe en v ehicles with b i-xenon
lights and halogen lamps:
• On vehicles with bi-xe non lights only the daytime runni ng lamps
in the headlights will come on .
• On ve hic les with halogen lights the fron t fog lights, s ide marker
lights and tail lights come on automatically
~
Vehicle care I I irechnical data

Clear vision
The daytime running lights function cannot be turned off .
Automatic headlight control *
In the switch position AUTO the automatic he adlight contro l is
turned on . The low beams are turned o n automatically through a
light sensor as soon as ambient brightness (e .g. when driving into a
t unnel) falls below a value preset at the factory. When ambien t
brightness increases again, the low beams are turned off again
aut omatically ==>&, .
In the
AUTO position the low beams are switched off automatically
when the ignition is turned off.
Light S ensor M alfun ction *
In the even t of a light sensor malfunct ion, the driver is notified in the
instrument cluster display :
Automatic headlights /automati c w ipers defe ctive
For safety reasons the low beams are turned o n permanently w ith
the switch in AUTO *. However , you can continue to turn the lights
on and off us ing the l ight switch . Have the lig ht sens or checked as
soon as possib le at a dealership .
Coming home /leaving home function *
The function is switched on when the switch is in the AUTO* posi ­
tion and the f unction is shown as ac tive in t he d river info rmat ion
system .
The
c oming home function illuminates the area around the vehicle
when the ignition is switched off a nd the driver's door is opened.
The length of time the lights remain on can be set in the menu
display
(Illumination > Exterior lights > coming home ).
The leaving home function illuminates the area around the vehicle
whe n unlocking it .
& WARNING
• Nev er use daytime run ning light s to see whe re you are going .
They are not bright enough and will not let you see far enough
ahead for safety , espe cially at du sk or when it i s da rk . Al way s
s w itch on the low beam s at du sk or when it i s dark .
• Automatic headlight s are only intended to assist the driver .
They do not relieve the driver of hi s responsibility to check the
head light s and to turn them on manually according to the cu rrent
light and visibility conditions . For example , fog and rain cannot be
detected b y the l ight sen sor s. S o alwa ys switch on th e headl ight s
under these weather conditions and when driving in the dark
io.
• Cra she s c an happen when you cannot see the road ahead and
when you cannot be seen by other motor ists.
- Alway s turn on the hea dlight s so that you can see ahead a nd
so that other s can see your car from the ba ck.
[ i ] Tips
• With the swi tch in AUTO front fog ligh ts cannot be turned on in
addition.
• The light sensor for head light contr ol is located in the rear view
mirror mount. Do not apply any stickers to the windshie ld in this
area to p revent malfunctions or failures.
• Some exterior lighting functions can be adjusted in the driver
informa tion system
==> page 23.
• I f you remove the ignition from the ignition lock while the head ­
l ights are still on, a bu zzer w ill sound as long as the driver's door is
open to remind you to turn off the lights.
• Always observe t he specific local regulations for your area as to
when to use your lights.
• With automatic headl ights, the high -beam function is also avai l­
able, but with one restriction : If you have not switched the high
bea ms back to low beams duri ng automatic headlight operation (for
example , after driving through a tunne l), on ly the low beams come .,,_

on the next time automatic headlights are switched on. To use the
high beams, you first have to pull the high beam lever back and then
push the lever forward again.
• In cool or damp weather, the inside of the headlights, turn
signals and tail lights can fog over due to the temperature differ­
ence between the inside and outside. They will clear shortly after
switching them on. This does not affect the service life of the
lighting.
• Frequent use of the coming home/leaving home function for
approaching and departing a vehicle parked in the dark will strain
the battery . This applies particularly if only short distances are
driven between stops. Occasionally drive longer distances to make
sure the battery is recharged sufficiently. •
Applies to vehicles: with Adap tive Light
Adaptive light
When driving around bends, the relevant area of the road
is better illuminated.
Fig. 48 Adaptive light
when driving
The benefit of adaptive light is that the curve and the edge of the
road are better illuminated::::} fig . 48 . The adaptive light is controlled
automatically, depending on vehicle speed and steering wheel
angle.
Con tro ls and eq uip­
ment
Clear vision
When driving around bends, the headlights are controlled
according to steering wheel angle. So that there is no black area
ahead of the vehicle, the two main beams pivot at different angles .
[ i] Tips
The system works above a speed of about 6 mph (10 km/hl. •
Front fog lights !O
Use the light switch to turn on the front fog lights.
Fig. 49 Fog light acti­
vation: light switch
position on vehicles
WITHOUT sensor light
Switching on the front fog lights !D
Do not turn the light switch ·'ti-·~ fig. 49 toward the fog
light symbol
Turn the light switch to
~oo: or to io.
Pull the light switch to the first stop G).
When the front fog lights are on, the symbol }O next to the light
switch will illuminate.•
Vehicle care I I Technical data

Clear vision
Instrument panel illumination
The ill umination of the instrumen ts, dis plays an d the
center cons ole c an be adjusted .
"' ;
a'.. ., m
Fig. 50 In stru men t
pan el illumi nat ion
You re gul ate the br ight ness o f the ins tru ments wit h the lef t
th um bw heel
C'1 => fi g. 50 .
Ignition ON , light switch at @ .
With the ignition switched ON, the g low of instrument needles can
be adjuste d to a ppear brigh ter or dimmer .
Ignition ON , light switch at ~oo : or tD.
With the l ights switched o n, the brightness of instrument c luster
(i.e . ne edles, gauges and displays) and center console il lumination
can be adjusted.
0 Note
The instrument cl uster and cente r console illumination (gauges and
needles) comes on when you switch on the ignition and the
v ehi cle
headlights are off.
Be aware of the f ollowi ng differe nce betwee n
models built to US or Canadian specifications :
• USA model s: illumination of the instrument cluster (gauges and
needles ), dash and center console around the gearshift leve r is
contr olled by a light sensor l ocated in the instrument panel. The i
nstrument panel illumination will autom ati cally be come dimmer
as the daylight fades away and eventually will go out completely
when out side light i s very low . Thi s is to rem ind you , the dri ver , to
sw itch on the headlights before it gets too dark.
• Canada models : in strument panel illumin ation will sta y bri ght
regardle ss of the inten sity of amb ient light . Alway s be aware of
c hange s in outside light conditions while you are d riving . Re spond
in time to fading dayl ight by turning the light switch to position
tD
(or" AUTO" if your car is equipped with this feature) to turn on your
he adl ights. •
Emergency flasher ~
The emergency flasher makes other motorists aware that
you or your vehicle are in an emergency situation.
1 1 0. -II 0 Ii i
11
u
I ] '
' F ig . 51 Center
c o ns ole : em erge ncy
fla sher swit ch
Pr ess th e sw itch ~=>fig. 51, to sw itch the em ergency
flas her on or off.
When the eme rgency flasher is on, al l four turn sig nal blink at the
same time . The turn signal indicator lights
¢i ¢ in the instrument
clu ster, as well as the light in the emergency flasher switch~ blink
likewise .
The emergency flasher will automatically switch on if you are in an accident where the airbag has deployed . _,,.

[ i J Ti ps
You should switch on the emergency flasher when:
• you are the last vehicle standing in a traffic jam so that any other
vehicles coming can see you, or when
• your vehicle has broken down or you are in an emergency s itua ­
tion, or when
• your vehicle is being towed by a tow truck or if you are towing
another vehicle behind you .•
Turn signals -¢ ¢ and high beam ~D lever
The lever on the left side of the steering column is used to
operate the turn signals and the high beam as well as the
headlight flasher .
-"' M
-w ... m
Fig. 52 Tu rn sign al and
hig h beam l ever
The turn signal and high beam lever has the following func­
tions:
Turn sign als
¢ ¢
- Lift the lever up all the way:::::, fig. 52 G), to use the right
turn s ignals, or push the lever down all the way@ to use
the left turn signals.
Con tro ls and eq uip­
ment
C lea r v is ion
Auto-blink
- Move the lever (up or down) just to the point of resis­
tance to use the turn signals for as long as you need
them, for example when changing lanes .
- Briefly move the lever up or down just to the point of resistance and then release it to flash the turn signals
three times in succession. This feature allows to indicate
lane changes clearly and with minimum effort when
driving on highways.
Hi gh b eam
~D
- Push the lever forward 0 to switc h on the high beam.
- P ull the lever back towards y ou to sw itch off the high
beam.
H eadlight flasher
~D
Pu ll the lever toward the steering wheel G) to use the
headlight flasher .
Note s on these features
• The turn signals only work with the ignition switched on. The
indicator lights
¢i or ¢ in the instrument cluster:::::, page 11 also
blink .
• After you have turned a corner, the turn signal switches off auto­
matically.
• The high beam works only when the headlights are on . The indi ­
cator light ~Din the instrument cluster illuminates when the high
beams are on.
• The headlight flasher works only as long as you hold the lever -
even if there are no lights switched on. The indicator light ~D in the
instrument cluster illuminates when you use the headlight flasher . .,
Vehicle care I I Technical data

Clear vision
0 Note
Do not use the high beam or headlight flasher if you know that these
could be blinding oncoming traffic. •
Interior lights
Interior lights and glove compartment light
The interior lights include the both reading lights for the
driver and the front passenger.
Fig. 53 Control panel
above windshield : inte­
rior light switches
Light switch => fig. 53 has the following functions:
Door contact activation
-Move the sw itch to the center position. The forward
dome light is turned on/off by the contact switches on
any of the doors .
Forward dome light on
-Move the switch to position I. The forward dome light
goes on and stays on regardless of door position.
Forward dome light off
- Move the sw itch to position 0 . The light w ill not go on
regardless of door position.
Glove compartment light
-Open the glove compartment -the light in the glove
compartment automatically illuminates as long as the
side marker lights or headlights are on. When you close
the glove compartment, the light goes off .
With the interior light switch at the door contact (center) position,
the forward dome light illuminates whenever you unlock the vehicle or op en a door . The dome light goes out after approximately 30
seconds after you have closed the door. Likewise , when you lock
your vehicl e or switch on the ignition, th e dome light goes out .
If you leave a door open, the dome light will go out after ten minutes
to conserve battery charge.
A dimmer automatically controls the brightn ess of th e lights when
they are switched on. •