check engine light AUDI S8 2010 Owner's Manual

Intelligent technology
'-----------------------------------------------
until the car starts to move . The whee l less ab le to transfer power
spins .
Overheating of brakes
To prevent the disc b rake of the bra ked wheel from ove rhea ting if
subjected to excessive loads, the EDL cuts out temporarily . The
veh icle remains operat ional and beh aves in the same way as a vehicle
without EDL .
As soon as the brake has coo led down, EDL switches on again auto­
matically .
& WARNING
• When a ccelerating on slippery surfaces, such as on ice or snow,
alw ay s be careful when depre ssing the a ccelerator pedal. E ven
with the EDL working, the drive wheel s can spin and reduce your
ability to control your car . Risk of crash !
• The in creased safety afforded by EDL does not mean that you
can take safety ri sks. Always adapt your driving st yle to the road
condition s and traffic situation .
fi Tips
If a fault occurs i n the ABS, the EDL is also no t fu nct ion ing . This is
indicated by the ABS warning light~
page 19. •
Anti-Slip Regulation System (ASR)
The Anti-Slip Regulati on System prevents the driven
wheels from spinning when the car is a ccel erating.
General notes
T he Anti-S lip Regulation System (ASR) is integrated in the electronic
stabilization program (ESP). When the veh icle starts up and acceler­
ates , the wheels are p reve nted from sp inning by adjust ing the eng ine
powe r to match t he amo unt of grip avai lab le from the road s urface.
How the system works
ASR perfo rms au toma tica lly, i .e . witho ut the drive r's in tervent ion .
With the aid of the A BS sensors~
page 256, ASR monitors the speed
of the driven wheels . If the wheels start to spin, the engine powe r is
reduced automat ically u nti l the t ires find enough gr ip to lock onto
the road s urface. The system is active across the entire speed range.
Th e ASR wor ks in con ju nction with the A BS .
If a m alfu nction sho uld
occur in the ABS, the ASR w ill also be out of action.
& WARNING
The increased safety afforded by ASR does not mean that you can
take safety ri sks . Always adapt your driving style to the road
condit ions and traffic situation.
[ i ] Tips
To ensure that the ASR works prope rly, all four wheels must be fitted
w ith ident ic a l ti res Any differences in rollin g radius of the tires can
cause the system to reduce engine power when t his is not desired .
See also ~
page 318, "N ew t ires and replacing tires and whee ls" .•
Braking
General Information
What affects b raking efficiency ?
Operating cond itions and driving habits
Th e bra kes on t oday's automo biles are still subjec t to we ar,
depending large ly on operating conditions a nd driving habits~ &.
O n ve hicles tha t are eithe r driven mostly in stop- and-go city t raff ic or
are drive n hard, the brake pads should be checked by your author ized
Audi de aler more o ften than specified in the
Warranty & Mainte­
nance booklet .
Failure to have your brake pads i nspected can result
in re duced brake pe rformance. .,

lillill.a._...:I:..: n~ t .::.e::::..::.: ll~igent technology ,_ _______________________________________ _
Brake booster
The brake booster adds extra braking power.
The brake booster works with vacuum pressure which is created on ly
w hen the eng ine is ru nn ing =>& .
& WARNING
• Nev er let the vehicle roll to a stop w ith the engine shut off.
• If the brake booster is n ot working , for e xample when towing
your vehicle, or because the brake booster has som ehow been
damaged , the brake pedal must be pressed conside rably harder to
make up for the lack of booster assistan ce. •
Functioning of Anti-Lock Brake System
(ABS)
A BS prevents the wheels fr om locking up under braking.
The ABS co ntributes effectively to ve hicle contro l s i nee it preve nts the
w heels from
locking when the brakes a re applied. T his means that the
vehicle remains steerable and is less likely to skid .
With ABS you do not need to pump the brake. Just hold the brake
pedal down.
However, do not expect the A BS to shorten brak ing distance under all
circumstances. When driving on grave l o r on newly fa llen snow on top
of icy su rfaces, b raking distance may be even longer, therefore, under
these circumstances, it is especially important that you drive slowly
and w ith great care.
How the ABS system works
An automatic check is made w hen a speed of abo ut 4 mph (6 km/h) is
reached . When this happens, a pumping noise can be heard . If a
n ind iv idua l wheel begins to rotate too slow ly in relat ion to ve hicle
speed and tends to lo ck, the ABS automat ically redu ces bra ke pres ­
su re to p revent t hat wheel from lock ing.
Th is automatic adjustment process wi ll cause a
slight vib ration of
t he bra ke pedal and so me noises to al er t you tha t vehicle s peed mus t
be adapted to existing road and traff ic conditions.
& WARNING
Although the ABS is very effective, always remember that braking
capability is limited by tir e traction. Always adjust your driving
speed acco rding to the road and traffic conditions. Do not let the
extra safety afforded by the ABS tempt you into taking extra ri sks .
The ABS cannot ove rcome the laws of physics.
[I) Tips
• If ABS is not funct ioning properly, a warning light will come on.
See=>
page 19.
• If a fa ult occ urs in the ABS, the ED L is also not functioning . This is
ind icated by the A BS warn ing ligh t.•
Brake assistant
T he brake assistant is designed to achi eve the optimum
b ra king effect.
The b rake ass istant helps to i ncrease the effective brak ing power and
thus to achieve a shorter stopping distance. If the driver p resses the
bra ke pedal
very quickly, the brake assistan t automatically boosts t he
brak ing fo rce to the maximum level, up to the po int where the anti­
lo ck bra ke f un ct ion (ABS) intervenes to stop the whee ls from locking.
You shou ld then keep the brake pedal pressed unt il the ve hicle has
bra ked to t he required s peed . T he bra ke ass ist ant sw itches itse lf off
as soon as you re lease the brake pedal. ._

Driving and environment
(I] Tip s
The consumption estimates as pub lished by ENV IRONMENTAL
PROTECTION AGENCY (EPA) and Transport Canada may not corre­
spond to your actual consumption on the road, which will vary
depending upon vehicle load and speed, road and weather conditions,
trip length, etc. •
Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are accelerating .
-Avo id unnecessary accelerating and braking.
Vehicles use the most fue l when they a re accele rating. If you antici­
pate what is going to happen next, you will need to brake less and,
thus, accelerate less. Let the vehicle coast whenever possible -for
example when you see that the next traffic l ight is red. •
Avoid full throttle
Driving at moderate speeds saves fuel and improves your
mileage.
- Try and keep well below your car's maximum speed .
Accelerating gently reduces fuel consumption, engine wear, and does
not disturb the environment.
Fuel consumption, exhaust emissions and engine noise increase
disproportionately at high speeds . If you drive at approx imately three
qua rters of top speed, fuel consumption will be reduced by one half.
Never drive faster than the posted speed limit and weather condi­
tions permit.
a Reducing unnecessary idling
Even when your car is just idling it burns up fuel.
-
Shut the engine off when yo u are not driving the vehicle.
- Do not warm up the vehic le by letting the eng ine run at
idle.
It makes sense to shut off the engine in traffic jams, when waiting for
trains to pass at rai lroad crossings, o r at traffic lights that have long
wa its on red . Turn ing the eng ine off for just 30-40 seconds saves
more fuel than is burned starting the engine again.
It takes a long t ime for the engine to warm up fully when it is running
at idle. Howeve r, wear and noxious emissions are espec ially high
when the eng ine is wa rm ing up. So you sho uld d rive away as soon as
you start the engine and avoid running at hig h rpms while the eng ine
is still warming up.
0 Note
Do not leave engine idling unattended after starting . If warning
lights should come on to indicate improper operation, they would go
unheeded. Extended idling also produces heat, which cou ld result in
overheat ing o r othe r damage to the vehicle or other p roperty. •
Regular maintenanc_e ____________ _
A badly tuned engine unnecessarily wastes a lot of fuel .
- Have your vehicle serviced at regular intervals .
By having yo ur vehicle regularly se rviced by an Audi dealer helps to
ensure that it runs properly and economically . T he condition of your
vehicle not only a ffects its safety and ability to ho ld its va lue, it a lso
affects
fu el con sumption .
Check your o il e ach tim e you fill you r tank.
~

Operating instructions
Maximum trailer weight
A trailer for your vehicle is limited to a typical class 1 or class 2 trailer.
Trailer load distribution
Be sure the load in the trailer is held securely in place to prevent it
from shifting forward, backward or sideways.
Never allow a passenger to ride in a trailer=>
& in "Driving instruc­
tions".
Engine cooling system
Towing a trailer makes the engine work harder. It is important that
the cooling system's performance is up to the additional load. Make
sure that the cooling system has enough fluid.
Tire pressure
When towing a trailer, inflate the tires of your vehicle to the cold tire
pressure listed under "Full load" on the label located either on the
driver's side B -pillar (visible when the door is open) or inside the fuel
filler flap. Inflate trailer tires to trailer and tire manufacturers' spec­
ifications .
Lights
The headlight settings should be checked with the trailer attached
before driving off. Check to make sure both vehicle and trailer lights
are working properly.
Safety chains
Be sure trailer safety chains are properly connected from the trailer
to the hitch on the vehicle. Leave enough slack in the chains to permit
turning corners . When you install safety chains, make sure they will
not drag on the road when you are driving.
The chains should cross under the trailer tongue to prevent it from
dropping in case of separation from the hitch .
Controls and equip­ ment Safety first Vehicle operation
Trailer
towingL_,1!:::!:·~-
0 Note
If you are going to tow a trailer, you must activate the trailer opera­
tion mode =>
page 179, "Towing a Trailer". •
Driving instructions
Driving with a trailer always requires extra care and
consideration .
To obtain the best possible handling of vehicle and trailer,
please note the following:
- Do not tow a loaded trailer when your car itself is not
loaded.
- Be especially careful when passing other vehicles.
- Observe speed limits.
- Do not drive at the maximum permissible speed.
- Always apply brakes early .
- Monitor the temperature gauge.
Weight distribution
Towing a loaded trailer with an empty car results in a highly unstable
distribution of weight. If this cannot be avoided, drive at very low
speeds only to avoid the risk of losing steering control.
A "balanced" rig is easier to operate and control. This means that the
tow vehicle should be loaded to the extent possible and permissible,
while keeping the trailer as light as possible under the circumstances.
Whenever possible, transfer some cargo to the luggage compart­
ment of the tow vehicle while observing tongue load requirements
and vehicle loading considerations.
Vehicle care Do-it-yourself service Technical data

___ C_h_ e_c _k _i_n -=g :a,__ a_n_ d_ f_ i_ l _li _n _,g;._ __________________________________________ _
Checking and filling
Engine hood
Releasing the engine hood
The engine hood is released from inside the vehicle.
Fig . 2 39 Dr iver 's sid e
f oo twell : e ng in e ho od
r elease leve r
-Pull the release lever on the left under the instrument
panel ~ fig. 239 in the dir ect ion of th e arrow .
The hood pops up slightly under spring pressure. •
Opening the engine hood
Fig. 24 0 Rel ease le v er
under the eng ine h ood
Before opening the eng ine hood, make sure that the wi nd­
sh ield wipers are flat against the windshield . Otherwise, t hey
cou ld damage the pa int on the hood.
Lif t the hood slightly~ &.
- Pull u p on t he rel ease un der the hood ~ fig . 240. This
releases the c atch .
- Open t he hood a ll the way.
& WARNING
Hot eng ine coolant can burn you.
• To reduce the risk of being burned , never open the hood if you
see or hear steam or coolant escaping from the engine compart ­
ment . Wait until no ste am or coolant can be seen or heard before
c arefull y opening the hood .•

___ C_h_ e_c _k _i_n -=g :a,__ a_n_ d_ f_ i_ l _li _n _,g;._ __________________________________________ _
& WARNING (continued)
-Always use extreme caution to prevent clothing, jewelry, or
long hair from getting caught in the radiator fan, V-belts or
other moving parts, or from contacting hot parts. Tie back hair
before starting, and do not wear clothing that will hang or
droop into the engine.
• Minimize exposure to emission and chemical hazards=:>
/1::..
& WARNING
California Proposition 65 Warning:
• Engine exhaust, some of its constituents, and certain vehicle
components contain or emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and reproductive harm. In
addition, certain fluids contained in vehicles and certain products
of component wear contain or emit chemicals known to the State
of California to cause cancer and birth defects or other reproduc­
tive harm.
• Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of California
to cause cancer and reproductive harms. Wash hands after
handling.
0 Note
When adding fluids, always make sure that they are poured into the
proper container or filler opening, otherwise serious damage to
vehicle systems wi ll occur.
ci> For the sake of the environment
To detect leaks in time, inspect the vehicle floor pan from underneath
reg ular ly. If yo u see spots from oil or other vehicle fluids, have your
vehicle inspected by an authorized Audi dea ler.•
Engine compartment
Applies to veh icles: w ith 8 -cylinde r engine
Engine compartment overview : a-cylinder
engine
These are the most important items that you can check.
Fig. 241 Typical layout for containers, engine oil dipstick and engine oil filler
cap
© Windshield/headlight washer container (0 ) ....... .
@ Brake fluid reservoir ( ) .................. .. .. . .
® Engine oil filler cap ('l=r.) ............ .. .... .. .. . .
© Engine oil dipstick (orange) .............. .. . ... . .
© Power steering reservoir . .. .. .. .. .. ... .... .. .. . .
© Coolant expansion tank (-L ) ........... .. .. .. .. . .
305
299
294
293
257
297 ..

___________________________________________ C_ h_e _c _k_ i_n ~g_ a_n_ d_ f_ i_ll _i_n _g __ _
the form of Serv ice or Repair O rde rs that all scheduled ma inte nance
w as perfo rm ed in a t im ely mann er.•
Engine oil consumption
Th e e ngin e in your v ehi cle dep ends on an ad equate
amount of oil to lubricate and cool a ll of its movin g parts.
In order to p rovide e ffect ive lubric ation and cooling of inter na l
eng ine components, all internal combust ion eng ines consume a
c ert ain a mo unt o f oil. Oil co nsump tion va ries from e ngine to eng ine
and may change sign ifican tly over the li fe of the engine . Typically,
eng ines w ith a sp ecifie d brea k-in period (s ee =>
page 261) co nsum e
more o il dur ing the break -in period t han they cons ume a fter oil
cons umption has stabilize d.
Under norm al cond itions, th e ra t e of oil con su mp tio n depe nds on t he
quality and v iscosi ty of the oil, the RPM ( revolutions pe r minute) at
w hich the engi ne i s op erate d, the ambie nt te m pe ratu re and r oad
conditions. Further factors are the amount of oi l di lution from water
co ndens ation or f uel re sidue and th e oxid ation level of the oil. As any
eng ine is s ubject to wear as mileage builds up, the oil consumption
may increase over time until replacemen t of wo rn components may
become necessa ry .
With all these varia bles comin g into play, no stan dar d rate of oil
co nsum ption can be establis hed o r spe cified. Th ere is no alte rnative
to regular and frequent chec kin g of the o il level, see
Note .
If the yellow e ngine oil leve l w arning symbol in the ins trumen t
cl uster · .. lights up, yo u should chec k the o il lev el as soon as possible
with the oil dipstick=> page 293 . Top off the oil at yo ur earliest
conveni ence=>
pag e 294 .
& WARNING
Before you check anything in the engine compartment , always
read and heed all WARNINGS=>
& in "Working in the engine
compartment " on
page 289.
Safety first
0 Note
Driv ing with an in sufficie nt o il level is like ly to c ause severe d amage
to the engine .
[ i ] Tips
• The oil pressure warn ing display 'e.::1; is not an indicator of the oil
level. Do not rely on it . Instead, check the oil level in your engine at
regular intervals, preferably each time you refuel, and always
before going on a long trip .
• If you have the impression your eng ine consumes excessive
am ounts of o il, we recom mend that you cons ult your Audi dea le r to
have the cause of your concern properly d iagnosed. Keep i n m ind that
t he accurate meas urement of oil co nsum ption re quires great care
and may take some t ime. Your Audi dealer has instruct io ns about how
t o meas ure o il cons umption a ccu ra tely .•
Checking the engine oil Level
Vehicle care
Fig . 24 3 Illustration
o f principle 1 : M arker s
on oil dipstick ...
Technical data

___________________________________________ C_ h _ e_c _k _ i_n -=g .._ a_n _ d_ f_i _ll _i _ n -=g '--- ....... 1!'1
0 Note
• Before winter sets in, have the coolant checked to see if the
coolant additive in your vehicle is sufficient to meet the climate
conditions. This is especially important if you live in a region where
the winter is extremely cold. If necessary, increase the proportion of
coo lant additive to 60% .
• When adding coolant additive to your cooling system, remember:
-We recommend using only coolant additive G12++ (check the
label) for your vehicle. This coolant additive is available at autho­
r iz ed Audi dealers. Other types of antifreeze can s ignificantly
reduce corrosion protection. The resulting corrosion can cause a
loss of coolant and serious engine damage.
• Do not add any type of radiator leak sealant to your vehicle 's
eng ine coolant. Adding radiator repair fluid may adversely affect the
function and performance of your cooling system and could result in
damage not covered by your New Vehicle Limited Warranty. •
Checking the engine coo lant level
The engine coolant level can be checked with a quick
glance.
.... N
Fig. 247 Engine
compartment: Coolant
expansion tank
Vehicle OP-eration
Before you check anything in the engine compartment,
always read and heed all WARNINGS=> & in "Working in
the engine compartment" on
page 289.
- Turn off the ignition.
- Read the engine coolant level from the coolant expansion
tank=> fig. 247 . With a cold engine, the coolant level
should be between the "min" and "max" markings. When
the engine is warm, the level may be slightly above the
"max'' marking .
The locat ion of the coolant expans ion tank can be seen in the engine
compartment illustration=>
page 290.
To obtain an accurate reading, the engine must be switched off.
The expansion tank in your vehicle is equipped with an electric coolant level sensor .
When the coolant level is too low, the warn ing light in the Auto-Check
System =>
page 29 will blink until you add coolant and the level has
been restored to normal. Even though there is an electric coolant
level sensor, we still recommend you check the coolant level from
time to time.
Coolant loss
Coolant loss may indicate a leak in the cooling system. In the event of
coolant loss, the cooling system should be inspected immediately by
your authorized Audi dealer .
It is not enough merely to add coolant.
In a
sealed system, losses can occur only if the boiling point of the
coo lant is exceeded as a result of overheating.
& WARNING
The cooling system is under pressure and can get very hot. Redu ce
the risk of scalding from hot coolant
by following these steps.
• Turn off the engine and allow it to cool down.
Vehicle care Do-it-yourselt service iTechnical data

lffll __ C_ h_ e_c _k _i _ n _g ~ a_n _d_ f_il _l_in _ g _________________________________________ _
& WARNING (conti nu ed )
• Protect your f ace, hand s and arms from e scaping fluid and
s team by covering the cap with a larg e, thick rag.
• Turn the cap slowl y and ver y ca refull y in a counter-clockwise
direct ion while applying light, downward pre ssure on the top of
the cap.
• To avoid being burned , do not spill antifreeze or coolant on the
exhaust system or hot engine part s. Under certain conditions, the
ethylene glycol in engine coolant can catch fire.
0 Note
Do not add any type of radiator leak sealant to yo ur vehicle's engine
coo lant. Adding radiator repair fluid may adverse ly affect the func­
t ion and perfo rmance of your cooling system and could result in
damage not covered by your New Vehicle Limited Warranty .
[ i J Tips
On vehicles with the 12-cylinder engine, the expansion tank is located
unde r a cover. •
Adding coolant
Be very careful when adding engine coolant.
Before you check anything in the eng ine compartment,
always read and heed all WARNINGS~ & in "Working in
t h e e ngine compar tment" on
page 289 .
-Tur n off the eng ine.
- Let t he engi ne cool down. -
Place a t hick rag over the coolant ex pansio n tank
~ page 297, fig . 247 and carefully twis t the ca p counte r­
clockw ise
~ & .
- Add coo lant.
- Tw ist t he cap on agai n
tightly.
Replacement eng ine coolant must conform to exact specificat ions
=> p age 2 96, "Coolan t". Even in an emergency, if coolan t ad di tive
Gl2 ++, Gl2+ or Gl2 is not available, do
not use a d ifferent addit ive.
Use plain water instead until you can get the correct additive a nd can
restore the correct ratio . This s hou ld be done as soon as possible .
If you have lost a conside rable amount of coolant , then you sho uld
add co ld a ntifree ze a nd cold water only when t he e ngine is cold .
Always use
new engine coo lant when refilling.
Do not fill coolant above t he "MAX" mark. Excess coo lant wi ll be
forced out t hrough the p ressure relief va lve in the cap w hen the
eng ine becomes hot.
& WARNING
• The cooling system is under pressure and can get very hot.
Reduce the risk of scalding from hot coolant by following these
steps.
- Turn off the engine and allow it to cool down .
- Protect your face , hands and arms from escaping fluid and
steam by covering the cap with a large, thick rag.
- Turn the cap slowly and very carefully in a counter-clockwise
direction while applying light, downward pressure on the top
of the cap.
- To avoid being burned , do not spill antifreeze or coolant on
the exh aust system or hot engine parts. Under certain condi-
tions, the ethylene gly col in engine coolant can catch fire. .,

Checking and filling ------------------------------- ---=.:..:..=.:=~..:::..:.....:..:.;__ ___ _::,______,.J
& WARNING (co ntinued )
• Antifreeze is pois onous. Alway s store antifreeze in its original
container and well out of the r each of children.
• If you drain the coolant , it must be caught and safely stored in
a proper container clearly marked "poi son ".
0 Note
• Coolant poll utes the environment and could cause an engine fire .
Excess coolant w ill be forced out throug h the pressure re lief valve in
t he cap when the e ng ine becomes hot .
• If, in an emergency, o nly wate r ca n be adde d, the correct ratio
between water and antifreeze=>
page 296 must be restored as soon
as possib le.
W For the sake of the environment
Dra ined coolant shou ld not be reused. A lways dispose of used coo lant
w hile observ ing a ll enviro nment al regul ations . •
Radiator fan
The radiator fan switches on automatically by itself
T he radi ator fa n is d riven by the engine via th e V-bel t. The v iscous
clutch regu lates the speed of the fan accord ing to the temperature of
t he coolant.
An auxiliary e lectr ic rad iator fan* sw itches on and off depend ing o n
coo la nt tempe rat ur e and othe r vehicle ope ra ting condi tions .
After you switch the engi ne off, the auxilia ry fa n can cont inue r unning
for up to 10 minutes - even w ith the ignition off . It can even switch on
agai n lat er by itse lf => & , if
• the tempe rature of the e ngine coolant rises due to the heat build ­
up from the eng ine in t he engi ne comp art ment, or
Vehicle OP-eration
• the engine compartment heats up because the veh icle is parked in
in tense s unlight.
& WARNING
• To reduce the ri sk of personal injury never touch the radiator
fan.
• The auxiliary electri c fan is temperature controlled and can
switch on suddenly even when the engine is not running .
• The auxiliary radiator fan switches on automatically when the
engine coolant reaches a certain temperature and will cont inue to
run until the coolant temperature drops .•
Brake fluid
Checking brake fluid level
T h e b rake fluid l evel can be ch ecked with a quick glance.
-w ;:;
Fig. 24 8 En gine
compa rtme nt: Brak e
f luid re se rv oi r
Be fore you chec k anyt hin g in the engine compartment,
always read and heed all WARNINGS~ & in "Working in
t h e engine compartm ent" on
page 289 . .,_
Vehicle care Do-it-yourselt service iTechnical data