AUDI S8 2010 Manual PDF

Instrument panel switch
-Press the G!;l switch to extend or retract the electric
sunshade for the rear window =>
page 68, fig. 62.
Rear switch
Press the rn switch to extend or retract the electric
sunshade for the rear window:::;,
page 68, fig. 63.
After the sun shade for the rear window has reached either of its end
positions, it turns off automat ically .
Briefly press the switch a second time to reverse the movement of the
sun shade before it reaches its end position . If the ignition is turned
off while the shade is still moving, the shade will continue until it
reaches the end position before turning off.
The rear w indow sun shade can be set in the MMI so that it retracts
automatically when driving in reverse. Select function button
I CAR I>
Systems > Window > Rear window sun shade> On to do th is . The sun
shade is extended again as soon as the vehicle is traveling forward at
a speed greater than 9 mph (15 km/h) if the ign ition has not been
switched off in the meantime . The current setting is automatically
stored and assigned to the remote key.
[ i ] Tips
• If the sun shade is operated repeatedly within a short time, the
built- in overload protection circuit may be tripped . If this occurs, you
will have to wait briefly before you can operate the shade again.
• Because of the decrease in the flexibility of the shade material at
temperatures below freezing, the e lectrica l circuit which operates
the shade shuts off when the temperature in the vehicle falls below
23 °F
( - 5 °C) . The shade cannot be operated until the passenger
compartment warms up above this temperature .•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
App lies to veh icles : wi th electric sunshad e fo r the r ear sid e w in dow s
Electric sunshade for the rear side windows
Each rear side window is equipped with an electric
sunshade.
Fig. 64 Roofli ning in
the rear: electric
su nshade but ton
You can operate the rear side window sunshades either by
using the power window switches in the driver's door, the
power window switches in the rear doors or the button
located in the rooflining in the rear of the vehicle .
Buttons in the rear of the vehicle
-Press the right or left button to lower or raise the
sunshade=> fig. 64.
Power window switch in the rear side doors
- Pull the switch to its second position and hold it there
briefly to lower the sunshade .
- Press the switch to its second position to raise the
sunshade.
Vehicle care Do-it-yourselt service iTechnical data

Clear vision Powe r window switch in th e driver's door
- Pull either of the two switches to its second position and
hold it there briefly . The sunshade will automatically
lower.
- Press the switch to its second position and the sunshade
automatically raises.
& WARNING
W hen lowe ring or r aisi ng th e s unshad e, make sur e there is
n othing in its w ay and tha t it h as a free path t o tra vel. Thi s could
ca us e pers onal in jury.
(I) Tips
The sunshade works only if the window is closed .•
App lie s to veh icles : w ith rear va nity mirro rs
Rear vanity mirrors
A pair of mirrors is mounted overhead within easy reach
of the rear passengers. When not in use, the mirrors are
folded up flush in the rooflining.
,--Fig. 65 Left rear roof­
lin ing: Vani ty mirror
f ol ded up flu sh Fi
g. 66 Left rear roof·
l ini ng: Vanity m irror
fo lded dow n
-To fold down, tap the rear edge of the mirror as indicated
by arrow =:, fig . 65 .
As the mirro r folds down , it au tomatically ill uminates .•
Wiper and washer system
,v,
Windshield wiper~
The windshield wiper lever controls both the windshield
wipers and the washer system.
0
"' M ~ w ;A
Fig . 67 Wi ndshie ld
wipe r leve r
The w indshield w iper lever =:, fig . 67 has the following posi­
tions :

Intermittent wiping ~l (acti vating rain
sensor )
- Move the lever up to position (D.
- Move switch @up or down , to adjust the sensitivity of the
rain sensor.
Low wip er sp eed
- Move the lever up to position@.
High wiper speed
- Move the lever up to position ®·
One-touch wiping
- Move the lever to position@, when you want to wipe the
windshield
briefly .
Automatic wiper /washer
- Pull the lever to position © (toward the steering wheel)
and hold.
- Release the lever . The washer stops and the wipers keep
going for about four seconds.
Turning off the wipers
- Move the lever back to positio n@ .
The windshield wipe rs and washer only work when the ignition is
turned on.
T he rain sensor is only activated with the wiper leve r set to position
@ . When i t starts to rain, the rain sensor will automatically activate
the intermittent wiping mode .
T o red uce the sensit iv ity of the senso r, move sw itch @down. To
increase the sensitivity, move the switch up . The higher you adjust the
Controls and equip ­
ment Safety first
Clear v
ision
sensitivity, the faster the sensor will react when it senses mo isture on
t he windsh ie ld. T he rain senso r wiper inte rvals depend on the sensi­
tiv ity setting as well as vehicle speed . During brief stops, w iper
motion will adj ust in relation to the amount of rain on the winds hield.
Dur ing b rief stops, e .g . at a red light , w iper motion will automatically
be reduced to the next lower speed. Wipers already turn ing at low
speed. c hange to intermittent w iping.
When the ign ition is turned on, the washer jets are heated.
With the low beam headlights switched on, pull the wiper lever
towards you o nly
briefly to clean the w indshield . Holding the wiper
lever would also engage the headlight washer system each time you
clean the w indshield and would d rain the washer fluid rese rvoir
prematurely .
& WARNING
• Wiper bl ade s a re cruci al for safe dri ving! Only when the y are in
good condition are th ey able to clear the wind ows properly to
pro vide uncompr omi sing visibilit y. Worn or damaged wipe r
blade s ar e a safet y hazard =>
pag e 73, "In stalling new wiper
blades "!
• The rain sensor i s only des igned t o assist and support the
dri ver. It rem ain s entirely the d river's re spon sibility to m onito r
out side weather condition s and to manually a ctivate the wipers as
soon a s rain or dr izzle reduce s visibil ity th rough the windshield.
• The win dshield mu st not be treated with wat er- re pellent
m aterial s. They c an in crease gla re under po or visibilit y condit ions
s u ch as wetn ess, darkne ss, or when the sun i s low on the horizon .
In addition , they can cause the wi ndshield wipers to chatter.
0 Note
In freezing or near freezing conditions:
• Always check that the wiper blades a re not frozen to the glass
before you turn the wipers on. Loosen a wiper blade which is fro zen in ..,
Vehicle care Technical data

Clear vision
place before operating the wipers to prevent damage to the wiper
blade o r th e wiper motor.
• Do not use the wipers to clear a frosted window. Us ing the wipers
as a convenie nt ice scraper wi ll dest roy the w iper blades .
• Before you take your vehicle to an automatic car wash, make sure
you have the w ind shield wipe r sys tem sw itched off (lever in posi tion
0), otherw ise the windshie ld wiper system cou ld get damaged in the
car w ash if i t shou ld sudden ly come on.
[ i ] Tips
• Make s ure the washe r flu id reservoir in the eng ine compa rtment is
topped off before going on a long trip . Look up~
page 305 for
check ing and filling the washer conta iner.
• If you switch off the ignition with the w indshield wiper lever still
in the inte rval wipe posit io n and then come bac k a w hile la ter and
dr ive off, the rain sensor will reactivate itself afte r the ve hicle speed
has exceeded 4 mph (6 km/h).
• Worn or d irty windshield w iper blades cause smear ing which can
affect the operation o f the rain senso r. Check the cond it io n of your
w indshield wiper b lades regularly .•
Headlight washer system
The headlight washer system cleans the headlights.
- Operate the wi ndsh ield wip er/was her syst em ® with the
headlig hts turned on by hold ing the lever for lo nger than
one second=>
page 70, fig. 67 .
The washer je ts extend fo rwa rd o ut of the front bumper driven by
water pressure to spray the front headlights w ith water .
You should inspect the headlights regu larly (for example when refu­
eling) and clean off a ny solid dirt o r insects from the lenses. To ensure the system works properly in winter, keep the washer jets
free o
f snow and remove any ice using a de- ic ing spray. •
Service position
The wiper blades can only be changed in the service posi ­
tion.
- At below freezing outside temperatures, make sure first
that the wiper blades are not frozen to the windshield .
- Select: Function b utt on
I CAR ]> System s > Windshield
wipers .
- Select Serv ice position on t o tu rn th e service position on
or
off to return t he windsh ield w iper to its or ig inal pos i­
tion.
You must only attempt to change the wiper b lades when the service
position is act ivated. This way, when you are working on the wind­
shield wipe rs, you can avoid damaging the paint on the engine hood.
[ i ] Tips
• You can also turn on the se rvice position, for examp le, if you want
to protect the windshield from ic ing, using a cover .
• T he service position t urns itself
off , whenever yo u use the w ind­
shield wiper lever .•

Installing new wiper blades
Wiper blades in good condition help keep the windshield
clear .
Removing a wiper blade
Fig. 68 Rem ov in g th e
wi per bla des
F ig . 69 Installi ng
wip er b lad es
- Bring the windshield wipers to the se rvice posi tion
~ page 72.
- Lift the wiper arm away from the windshield .
- Push the locking piece on the wiper blade in the direct ion
of t he arrow @~ fig . 68 . Ho ld the wipe r blade firmly.
- Remove the w iper blade@.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
Installing wiper blade
- Place the new wiper b lade in th e retaine r on the wiper arm
@ ~fig. 69.
- Push the locking piece on the wiper blade in the direction
o f the arrow ® until you feel it click into place on the
wrper arm.
Clean your wiper blades regular ly with a windshie ld washer so lution
to p revent streaking.
If the b lades are very dirty, for example wi th
insects, carefu lly clean the blades with a sponge or a soft brush .
If the w iper blades begin to streak the w indshield, this could be
caused by res idue left on the windsh ie ld by au tomatic car washes .
Fill the windshie ld washer container with a specia l solution availab le
a t you r author ized A udi dealer to remove the res idue.
& WARNING
Be sur e to in spe ct the conditi on of your wiper blades regularly . See
your authorized Audi de ale r for replacement blades .
0 Note
To prevent damage to the wiper system:
• Always loosen blades wh ich are frozen to the wi ndshield before
operating wipers.
• Do not use gasoline , ke rosene, paint th inner, or ot her solvents on
or near the wiper blades .
• Do not at tempt to move the w ipers by hand.
[I] Tips
Commercial hot waxes applied by automatic car washes affect the
cleanability of the windshield. •
Vehicle care Do-it-yourselt service iTechnical data

Clear vision
Mirrors
Rear view mirror
When the ignition is on, t he interior m irro r will darken automatically
depending on t he amo unt of light strik ing the m irro r (such as head­
lights shin ing into the veh icle from the rear) . The mirro r will retu rn to
the o rigi na l state (anti -glare off) when yo u move the manua l gear­
shift/gear se lector lever into
Reverse or w he n you turn o n the in te rior
lights .
& WARNING
Broken glass of automatic dimming mirror can cause electrolyte
fluid l eakage . Electrolyte fluid can irritate skin, eyes, and respira­
tory system .
• Repeated or prolonged exposure to electrolyte can cause irrita ­
tion to the respiratory system , especially among people with
asthma or other respiratory conditions . Get fresh air immediately
by leaving the vehicle or , if that is not possible , open windows and
doors all the way .
• If electrolyte gets into the eyes , flush them thoroughly with
large amounts of clean water for at least 15 minutes; medical
attention is recommended.
• If electrolyte contacts skin, flush affected area with clean
water for at least 15 minutes and then wash affected area with
soap and water; medical attention is recommended. Thoroughly
wash affected clothing and shoes before reuse.
• If swallowed and person is conscious, rinse mouth with water
for at least 15 minutes. Do not induce vomiting unless instructed
to do so by medical professional. Get medi cal attention immedi­
ately.
[I] Tips
T he au tomati c anti-glare feature on the mi rro r will not operate prop­
erly if the lig ht shini ng on the inside mir ror is blocked by othe r
objec ts. •
Outside mirrors
The outside mirrors are elec trically a djust ed.
Adjusting the outside mirrors
Fig . 70 F orw ard
section of d river 's
armrest : power mi rro r
c on trols
- Tur n th e ad jus ting k nob to posi tion (0 ~ fig. 7 0 to ad just
the outside m irror on the drive r's s ide.
- Tur n the k nob to posit io n ® to adjust t he out side mirror
on the passe nger side.
- Pr ess t he knob i n th e ap propriate direc tion to move t he
mirror s urf a ce so tha t you have a goo d view to the r ear .
Folding both outside mirrors in flush
- Turn the knob to@ .
The m irro r sur faces are heated whe never you switch on the rear
w indow defogger in re sponse to the o utside temperature.

You are well-advised to fold the outside mirrors in when maneuvering in tight spaces or w hen leaving t he car pa rked close to othe r vehicles.
Tilting the passenger's side outside mirror
When yo u move the se lecto r lever in to R (Reve rse), the mi rror on the
front passenger's door (knob turned to® =>
page 74, fig . 70) w ill tilt
sligh tly downw ard. This make is easier for you to see the curb when
you are back ing into a parking space .
The mirror returns to its initial position as soon as reverse gear is disengaged and vehicle speed is above about 9 mph (15 km/h). The
mirror also returns to its initia l position if the switch is moved to the
dr iver's ou ts ide mir ror © or Neutral @ .
Memory setting for the outside mirrors
When the seat position is saved in memo ry, t he position of the
outs ide mirrors is saved at the same time=>
page 84.
Automatic anti-glare for the outsid e mirro rs
The o utside mir rors dim at the same time as the inside mirro r. When
the ign ition is sw itched on, the mirrors automatically dim depend ing
on the amo unt of light strik ing the m irro rs (such as head lights
shini ng into the veh icle from t he rear) .
When you turn on the inter ior light, or when you move the se lector
lever in to R (Reve rse), the anti-glare f unct ion s tops and the mir rors
return to their orig inal condition (not darkened) .
& WARNING
Broken glass of automatic dimming mir ro r can cause electrolyte
fluid leakage . Electrolyte fluid c an irritat e skin, eye s, and respira­
tory system.
• Repeated or prolonged e xposure to electrolyte can cause irrita ­
tion to the resp iratory system, especially among people w ith
asthma or other re spiratory condition s. Get fresh air immediately
by leaving the vehicle or, if that is not possible , open windows and
door s all the way.
Controls and equip ­
ment Safety first
Clear v
ision
& WARNING (co ntinued )
• If electrolyte get s into the eye s, flu sh them thoroughly with
large amount s of clean water for at l east 15 minut es; medical
attention i s re commended .
• If electrolyte contact s skin, flush affected area w ith clean
water for at least 15 minute s and then wash affe cted area with
soap and water; medical attention is recommend ed . Thoroughly
wash affected clothing and shoes befo re reu se.
• If swa llowed and person is consciou s, rinse mouth with water
for at least 15 minutes. Do not induce vomiting unle ss instructed
to do so by medical prof essional. Get medi cal attention immedi­
atel y.
0 Note
• Curved (i.e. convex) mirror surfaces increase yo ur field of v iew .
Remembe r th at vehicles or o ther objects will appea r smalle r and
farther away than when seen in a flat mirror. If you use this mirror to es tima te dist ances of following veh icles whe n chang ing lanes, yo u
cou ld estimate incorrectly and cause an acc ident .
• If the mirror ho using is moved un intent io na lly (for examp le, w hile
parking your ve hicle), then you must first fold the mirror electr ically.
Do not read just the mirro r ho using manually. Yo u could damage the
motor w hich controls the mirror .
[ i ] Tips
• If
there should be a malfunction in the electrical system, you can
sti ll adjust the outs ide mir rors by pressing the edge of the mirror .
• The au tomatic anti-glare feature on the mirror will not operate
prope rly if the light sh ining on the i nside m irro r is bloc ked by ot her
objects .•
Vehicle care Technical data

Seats and storage
Seats and storage
General recommendations
Why is your seat adjustment so important?
The safety belts and the airbag system can only provide
maximum protection if the front seats are correctly
adjusted.
Th ere a re va rious ways of ad justing t he fro nt seats to provide safe and
comfor ta ble suppo rt for th e dr iver and the front passenger . Ad just
your sea t properly so that :
• you can eas ily and quickly reach all the switches and controls in t he
in st rumen t pa nel
• your body is prope rly s upported th us reducing phys ica l stress and
f a tigue
• the safety be lts and airbag system can offe r maxim um protection
:::;, pag e 206.
In the following sect ions, you will see exactly how you can best ad just
your sea ts .
Th ere a re sp ecial regulations and instr uct io ns for installing a ch ild
sea t on the front passenge r's sea t. Always follow t he informat ion
r e gar ding ch ild safety provided in ::;,
pag e 231, "C hi ld Safety ".
L1}. WARNING
Incor rect seat ing position of the driver and all othe r passengers
can result in serious personal injury .
• Always keep your feet on the floor when the vehicle is in
motion -never put your feet on top of the instrument panel , out
of the window or on top of the seat cushion . This applies especially
to the passengers. If your seating position is incorrect, you
increase the risk of injury in the case of sudden braking or an acci-
& WARNING ( continued )
dent. If the airbag inflates and the seating position is incorrect,
this could result in personal injury or even death.
• It is important for both the driver and front passenger to keep
a distance of at least 10 inches (25 cm) between themselves and
the steering wheel and /or instrument panel. If you 're sitting any
closer than this , the airbag system cannot protect you properly. In
addition, the front seats and head restraints must be adjusted to
your body height so that they can give you maximum protection.
• Always try to keep as much distance as possible between your­
self and the steering wheel or instrument panel.
• Do not adjust the dr iver's or front passenger's seat while the
vehicle i s moving. Your seat may move unexpectedly , causing
sudden loss of vehicle control and personal injury. If you adjust
your seat while the vehicle is moving , you are out of position.•
Driver's seat
Th e correct seat p osition is important for safe and
re lax ed driving.
W e recomme nd that you a djust t he dr ive r's sea t in t he
follow ing ma nne r:
- Adjust t he seat i n fore and aft d irect ion so t hat you can
easily p ush t he peda ls to the floor whi le keep ing your
k n ees sli ghtly bent =>
& in " Why is yo ur seat adjust men t
so impo rtan t?".
- Adjust t he seatback so t hat wh en you s it with you r bac k
agai nst t he seatbac k, you can st ill g rasp t he top of t he
steer ing wheel. ..,_

-Position the head restraint according to the occupant's
height ~
page 81. For maximum protection, the top of
the head restraint should be at least at eye level, prefer­
ably higher and ideally level with the top of the head
~ page 191, fig. 200.
& WARNING
Never place any objects in the driver's footwell. An object could
get into the pedal area and interfere with pedal function. In case
of sudden braking or an accident, you would not be able to brake
or accelerate. •
Front passenger's seat
Always move the front passenger seat into the rearmost
position.
To avoid contact with the airbag while it is deploying, do not
sit any closer to the instrument panel than necessary and
always wear the three-point safety belt provided adjusted
correctly. We recommend that you adjust the passenger 's
seat in the following manner:
- Move the front passenger seat into the rearmost position
of the fore and aft adjustment range~
& in "Why is your
seat adjustment so important?" on
page 76.
- Bring the backrest up to an (almost) upright position.
Do
not ride with the seat reclined.
- The ideal position for the head restraint is with the upper
edge of the restraint level with the top of your head
~ page 81. You should not lower the top of the restraint
below the level of your eyes.
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Seats and storage
-Place your feet on the floor in front of the passenger's
seat. •
Power seat
Controls
The operating logic for the switches corresponds to the
construction and function of the seat.
Fig. 71 Power seat:
Controls for seat
adjustment
The switches to adjust the seats correspond to the layout, the design
and the function of the seat. The seats are adjusted by moving the
switches following this logic.
© Upper thigh support~ page 78
@ Seat adjustment ~ page 78
© Massage funct ion* ~ page 79
@ Seatback angle~ page 79 and head restraint~ page 81 adjust-
ment
© Separa te adjustmen t of upper sea tback section ~ page 79
© Adjusting the lumbar support~ page 80
© Safety belt height adjustment~ page 204 ..,
Vehicle care Do-it-yourselt service iTechnical data

Seats and storage
& WARNING
• Never adjust the driver's or front passenger's seat while the
vehicle is moving. If you do this while the vehicle is moving, you
will be out of position. Always adjust the driver's or front passenger's seat when the vehicle is not moving.
• Be careful when adjusting the seat height. Check to see that no
one is in the way, or serious injury could result!
• Because the seats can be electrically adjusted with the ignition
key removed, never leave children unattended in the vehicle.
Unsupervised use of the electric seat adjustments may cause
serious injury. •
Upper thigh support
The adjustable upper thigh support provides optimal
support for the upper thigh when driving.
___ .. _:_·_-_.-_--·-·------·---.... _-_ ---.. ·-:.-_
Fig. 72 Power seat:
Switch for upper thigh
support
- To extend the upper thigh support , push the switch
forward.
- To make the upper thigh support shorter, push the switch
to the rear.
& WARNING
Never adjust the seat cushion while the vehicle is moving. If you
adjust your seat while the vehicle is moving, you are out of posi­
tion. Always adjust the seat cushion when the vehicle is not
moving. •
Seat adjustment
Fig. 73 Power seat:
Switch for seat adjust­
ment
Moving the seat forward and backward (D
- Press the switch forward or backward horizontally=>&.
Adjusting the seat height 0 and ® together
-Pull the switch evenly at both ends to raise the seat =:>& .
-Push the switch evenly at both ends to lower the seat
=> & .
Angling the seat cushion up and down@ or®
-To angle the seat cushion up, pull the switch at the front
only =>& .
-Alternatively, push the switch at the rear only=>& . .,_