light AUDI TT ROADSTER 2011 Workshop Manual

92 Transmission
-Only use Launch Control when road and
traffic conditions allow it and other driv­
ers will not be endangered or annoyed by
your driving and the acceleration of the
vehicle.
- Make sure that ESP remains enabled.
With the ESP disabled, the vehicle could
brake away, particularly on a slick and
slippery road -risk of skidding!
- Once acceleration is finished, switch ASR
on again by briefly pushing the ESP but­
ton.
Back -up program
In the event of a system malfunction, there is
an back-up program .
In the event of system malfunction, the auto­
matic transmission switches to the fail-safe
mode . All of the selector lever position dis­
plays for the automatic transmission are high­
lighted with a light background in the instru­
ment cluster display . In some cases you can­
not use reverse gear any more.
If the transmission switches to fail-safe
mode, you should take the vehicle to an au­
thorized Audi dealership as soon as possible
to have the condition corrected.
Clutch is overheating
• Clutch is overheating! Please stop vehi­
cle!
If the symbols are illuminated, the clutch is
overheating and could be damaged if you con­
tinue to drive . Stop the vehicle and allow the
transmission to cool with the selector lever in
the
P position while the engine runs at idle. If
the warning does not turn off, do not continue
driving. See your authorized Audi dealer or
qualified repair facility for assistance. Other ­
wise serious transmission damage could re­
sult. Once the indicator light has turned off,
drive to your authorized Audi dealer or quali­
fied repair facility immediately to have the
malfunction corrected.
Selector lever emergency release
If the vehicle 's power supply fails, the selec­
tor lever can be released in an emergency.
-
-
-
-
-
-
---Fig. 102 Selector lever: Removing t he selector lever
boot
Fig. 103 Selector lever: Using the e merge ncy release
to move o ut of the Park pos it ion
The emergency release mechanism is located
in the right front area under the selector lever
shift gate. Using the emergency release can
be complicated. We recommend contacting
your authorized Audi dealer for assistance, if necessary .
Removing the selector lever boot
.. Activate the parking brake.
.. Carefully pry the selector lever boot out of
the trim @ using a small screwdriver .
.. Pull both sides of the selector lever boot up-
ward in the direction of the arrow @.
.. Fold the selector lever boot upward.
Selector lever emergency release
.. Press the release lever down and hold it in
place
~ fig . 103 .
.. Press the release button in the selector lever
© and move the lever into the N position. Iii>

94 Homelin k®
Homelink ®
Universal remote
control
General information
The Homelink ® feature can learn up to three
radio frequency codes for most current trans­
mitters used for operating garage doors, es­ tate gates, home or outdoor lighting sys­
tems , and other devices.
You must first program the Homelink ® trans­
mitter before you can use the system
¢ page 95, Programming the HomeLink ®
transmitter.
In order to program the Home Link ® transmit­
ter for devices utilizing rolling code, a second person on a ladder who can safely reach the
garage door opener motor is recommended.
It is also necessary to locate the "learn" but­
ton on your garage door opener motor . Refer
to the operating instructions for the opener,
as the location and color of this button may
vary by manufacturer .
You can still use the original remote control
for the device at any time.
A WARNING -
- Never use the Homelink® transmitter
with any garage door opener that does
have not the safety stop and reverse fea­
ture as requ ired by federal safety stand­
ards. This includes any garage door open­
er mode l manufactured before April 1,
1982.
- A garage door opener which cannot de­
tect an object, signaling the door to stop
and reverse does not meet current feder­
al safety standards. Using a garage door
opener without these features increases
risk of serious injury or death.
- For safety reasons never release the
parking brake or start the engine while
anyone is standing in front of the vehicle .
- A garage door or an estate gate may
sometimes be set in motion when the Homelink
® remote control is being pro­
grammed. If the device is repeatedly ac­
tivated, this can overstrain motor and
damage its electrical components -an
overheated motor is a fire hazard!
- To avoid possible injuries or property
damage, please always make absolutely
certain that no persons or objects are lo­
cated in the range of motion of any
equ ipment being operated.
0) Tips
- If you would like more information on
Homelink®, where to purchase the
Homelink ® compatible products, or
would like to purchase the Homelink ®
Home Lighting Package, please call toll­
free: 1-800-355-3515.
- For Declaration of Comp liance to United
States FCC and Industry Canada regula­
tions ¢
page 244.

Programming the Homelink®
transmitter
The transmitter is programmed in two phas­
es. For rolling code transmitters, a third
phase is also necessary.
F ig . 104 Overhead console: Homelink ® keypad
Fig. 105 Front bumper, driver side: locat ion of trans ­
mitte r unit
Phase 1:
programming the overhead keypad
1. Make sure your vehicle is w ith in operat ing
ra nge of the remote controlled garage
door opener .
2. Set the parking brake~&.
in General in­
formation on page 94.
3. Turn the ignition on . Do not start the en­
g ine!
4 . Press and hold the two outside Home­
Link ® buttons
(D and @for approxi­
mately 20 seconds until indicator light@
~ fig. 104 begins to flash . Then release
both buttons . Do not hold the buttons for
longer than 30 seconds.
.. This procedure only needs to be performed
once. It erases the factory-set default codes
and does not have to be repeated to pro­
gram additional remote controls .
Homelin k® 95
5. Press and ho ld the Homelink ® button (D ,
@ or§ until the indicator light@
starts flashing
slowly . Release the button.
.. The system will remain in programming
mode for 5 minutes.
Go to the front of the
vehicle and proceed with phase 2 .
Phase 2:
programming the bumper mounted trans
mitter
6. Hold the original remote control at a d is­
tance between
0 -6 in. (0 -15 cm) from the
bumper below the appropr iate headlight
for your vehicleQ
fig . 105 (use the short­
est distance possible) .
7. Aim the remote control just below the
driver side headligh t.
8. Press and hold the activation button on
the remote control.
.. May be different in Canada . If so, press and
re-press (cycle) the activation button on your
remote control every two seconds .
9. The emergency flashers will flash
three
times
(after about 15-60 seconds) when
the programming is successful. Re lease
the button on the remote control.
.. To program more devices, repeat steps 4 to
9.
10. Press and hold the trained Homelink ®
button and observe the indicator light @
Qfig . 104.
.. If the indicator light is solid/continuous,
programm ing is complete and your device
should activate when you press and release
the trained Homelink ® button.
.. If the indicator light blinks rapidly for 2 sec ­
onds and is then a solid/continuous light,
proceed w ith phase 3 to program a rolling
code device.
Phase 3: rolling code programming
.. A second person on a ladder who can safely
reach the garage door opener motor is rec ­
ommended .
11. Locate the "learn" button on the garage
door opener motor (refer to the operating
instructions for the opener, as the loca­
tion of this button may vary by manufac­
turer) .

96 Homelink®
12. Press and release the learn button on the
garage door opener motor.
• Note: once the button is pressed, there are
30 seconds in which to initiate the next
step.
13 . On the Homel ink ® keypad inside the vehi ­
cle, firmly press and hold the Homelink ®
button previously programmed in phases
1 and 2 for two seconds and release. Re­
peat this sequence
twice .
• Some vehicles may require the press/hold/
release sequence up to t hree times to com­
plete the training process.
• HomeLink ® should now activate your rolling
code equipped device.
If the 5 minute time limit is exceeded, the
emergency flashers will flash one time to in­
d icate that the process has been terminated.
In this case, repeat steps 4 through 9 .
If the emergency flashers do not flas h
three
times (after about 15-60 seconds), program­
ming was not successful. In this case, repeat
steps 4 through 9.
Remote control units for garage door openers
i n Canada are set to stop transmitting radio
frequency signals after two seconds. This time
may not be sufficient for the Homelink ® sys­
tem to learn the radio frequency s ignal. Per­
form all other steps as described above .
Operating the Homelink® transmitter
The HomeLink ® transmitter works in the
same manner as the original handheld re­
mote control that came with the system .
Fig. 106 Overhead console: Homelin k® keypad
• Press the appropr iate p rogrammed button
(D, ® or@ to activate the desired remote
contro l function
~ A in General informa­
tion on page 94.
Reprogramming a single button
A HomeLink ® button can be reprogrammed
individually without affecting the other but­
ton allocations.
Programming the overhead keypad
• Press the appropriate Homelink ® button un-
til the indicator light begins flashing slowly.
Programming the bumper mounted trans
mitter
1. Hold the original remote control at a dis ­
tance between
0-5 i n. (0 -13 cm) from the
bumper below the appropriate headlight
for your vehicle (use the shortest distance
possible) .
2. Aim the remote control just below the
driver side headlight .
3 . Press and hold the act ivation button on
the remote control.
4. The emerge ncy flashers will flash
three
times
(after about 15-60 seconds) when
the programming is successful. Now re­
l ease the button on the remote control.
• If the device utilizes a rolling code, please
follow phase 3 of
c:> page 95, Programming
the HomeLink ® transmitter
for rolling code
programm ing .
This procedure will cause the existing pro­
gramming on the Homelink ® button to be
erased!
Erasing the programming of the
Homelink ® transmitter
When you erase the programming, the pro­
gramming on all three of the transmitter
channels with be lost!
.,. Perform steps 1 to 4 as described on
c:> page 95, Phase 1: programming the over-
head keypad . ..,.

98 Driving Safel y
Driving Safely
General notes
Safe driving habits
Please remember -safety first!
This chapter contains important information,
tips, instructions and warnings that you need
to read and observe for your own safety, the
safety of your passengers and others . We have
summarized here what you need to know
about safety belts, a irbags, ch ild restra ints as
well as child safety. Your safety is for us
priori­
ty number 1.
Always observe the info rmat ion
and warn ings in th is sect ion -fo r yo ur own
safety as well as for that of your passengers.
The information in this se ction app lies to all
model ve rsions of your veh icle . Some of the
feat ures desc ribed in this sec tions may be
standa rd equipment on some models, or may
be optional equipment on others . If you are
not sure, ask your authorized Aud i dealer.
A WARNING
- Make certain that you follow the instruc­
t ions and heed the WARNINGS in this
Manual. It is in your interest and in the
interest of your passengers .
- Always keep the complete Owner's Liter­
ature in your Audi when you lend or sell
yo ur vehicle so that this important info r­
mation will a lways be ava ilable to the
dr iver and passenge rs.
- Always keep the Owner's literature handy
so that you can find i t eas ily if yo u have
ques tions.
Safety equipment
The safety features are part of the occupant
restraint system and work together to help
reduce the risk of injury in a wide variety of
accident situations.
Your safety and the safety of your passenge rs
should not be left to chance. Advances in
technology have made a varie ty o f fea tures
avai la bl e to he lp re duce the risk of injury in an accident
. The following is a lis ting o f just a
few of the safety features in your Audi:
- sophis tic ated s afety be lts fo r drive r and a ll
passenger sea ting pos it ions,
- safety belt pre-tensione rs,
- fro nt airbags,
- knee airbags for the front seats,
- side airbags in the front seats,
- LATCH anchorages for child restraints,
- ad justab le steering column .
T hese ind iv idual safety features can wor k to­
ge ther as a sys tem to he lp p rotec t you and
you r passengers in a wide range of accidents.
These features cannot wo rk as a system if
they are not always p roper ly adjusted and
properly used!
Safet y is everybody's re sponsibilit y!
Important things to do before driving
Safety is everybody's job! Vehicle and occu­
pant safety always depends on the informed and careful driver.
For yo ur safe ty and the safety of you r passen­
gers,
befor e driving alwa ys:
"' Make s ure that all lights and signa ls are op­
erati ng correctly .
"' Ma ke su re t hat the t ire p ressu re is co rrec t.
"' Mak e su re that all windows are clean and a f­
ford good vis ibility to the outs ide.
"' Sec ure all luggage and other items caref ully
I:!) page 7 3.
"'Make sure that nothing can interfere with
the pedals.
"' Adjust front seat, head restraint and mirrors
correctly for your height .
"' Inst ruct passe ngers to adjust the head re­
st raints accord ing to the ir height .
"' Ma ke sur e to use the r igh t chi ld restraint
correc tly to protect c hild ren
¢ page 136,
Child Safety .
"'Sit properly in your seat and make sure that
your passengers do the same
I:!) page 66,
General recommendations. .,_

.. Fasten your safety belt and wear it properly.
Also instruct your passengers to fasten the ir
safety belts proper ly ¢
page 107 .
What impairs driving safety?
Safe driving is directly related to the condi­
tion of the vehicle, the driver as well as the
driver's ability to concentrate on the road
without being distrac ted.
The driver is responsible for the safety of the
veh icle and a ll of its occupants . If your ability
to drive is impaired, safety risks for everybody
in the vehicle increase and you also become a
hazard to everyone else on the road ¢
,&..
Therefore:
.,. Do not let yourself be distracted by passen ­
gers or by us ing a cellular telephone .
.. NEVER dr ive when your driv ing ability is im ­
paired (by medicat ions, alcohol, drugs, etc.) .
.. Observe all traffic laws, ru les of the road
and speed limits and plain common sense .
.. ALWAYS adj ust yo ur speed to road, traff ic
and weather condit ions .
.. Take frequent breaks on long trips . Do not
drive for more than two hours at a stretch .
.. Do NOT drive when you are tired , under
pressure or when you are stressed.
A WARNING
Impaired driving safety increases the risk
of serious personal injury and death when­
ever a veh icle is being used .
Drivin g Sa fely 99
Proper occupant
seating positions
Proper seating position for the driver
The proper driver seating position is impor­
tant for safe, relaxed driving.
Fig . 107 The correct d istance betwee n drive r an d
stee ring wheel
Fig . 1 08 Co rrec t head rest raint pos it ion fo r dr ive r
For your own safety and to reduce the risk of
injury in the event of an accident, we recom­
mend that you adjust the driver's seat to the
fol low ing position:
.,. Adjust the driver 's seat so that you can easi­
ly push the pedals all the way to the floor
while keeping your knee(s) slightly bent
<=> ,& .
.. Adjust the angle of the seatbac k so that it is
in an upright position so that your back
comes in full contact with it when yo u drive .
.. Adjust the steering wheel so that there is a
distance of at least 10 inches (25 cm) be­
tween the steering wheel and your breast
bone
c:> fig . 107 . If not possible, see your au ­
thorized Audi dealersh ip about adaptive
equ ipment .
.. Adjust t he steer ing wheel so that the steer­
ing wheel and a irbag cover poi nts at your
chest and not at your face .

100 Driving Safely
• Grasp the top of the steering wheel with
your elbow(s) slightly bent.
• Adjust the head restraint so that the upper
edge is as even with the top of your head as
possible but no lower than eye level and so
that it is as close to the back of your head as
possible
t::;> fig. 108 .
• Fasten and wear safety belts correctly
t::;> page 110.
• Always keep both feet in the footwell so
that you are in control of the vehicle at all
times.
For detailed information on how to adjust the
driver's seat, see
¢page 67 .
.&_ WARNING
Drivers who are unbelted, out of position
or too close to the airbag can be seriously
injured by an airbag as it deploys. To help
reduce the risk of serious personal injury:
- Always adjust the driver's seat and the
steering wheel so that there are at least
10 inches (25 cm) between your breast­
bone and the steering wheel.
- Always adjust the driver's seat and the
steering wheel so that there are at least
4 inches (10 cm) between the knees and
the lower part of the instrument panel.
- Always hold the steering wheel on the
outside of the steering wheel rim with
your hands at the 9 o'clock and 3 o'clock positions to help reduce the risk of per­
sonal injury if the driver's airbag inflates.
- Never hold the steering wheel at the
12 o'clock position or with your hands at
other positions inside the steering wheel
rim or on the steering wheel hub. Hold­
ing the steering wheel the wrong way
can cause serious injuries to the hands,
arms and head if the driver's airbag in­
flates
- Pointing the steering wheel toward your
face decreases the ability of the supple­
mental driver's airbag to protect you in a
collision.
- Always sit in an upright position and nev­
er lean against or place any part of your body too close to the area where the air­
bags are located.
- Before driving, always adjust the front
seats and head restraints properly and make sure that all passengers are prop­
erly restrained .
- Never adjust the seats while the vehicle
is moving. Your seat may move unexpect­
ed Ly and you could lose control of the ve­
hicle .
- Never drive with the backrest reclined or
tilted far back! The farther the backrests
are tilted back, the greater the risk of in­
jury due to incorrect positioning of the safety belt and improper seating posi­
tion .
- Children must always ride in child seats
t::;> page 136. Special precautions apply
when installing a child seat on the front
passenger seat
t::;> page 115.
Proper seat ing position for the front
passenger
The proper front passenger seating position
is important for safe, relaxed driving.
For your own safety and to reduce the risk of
injury in the event of an accident, we recom­
mend that you adjust the seat for the front
passenger to the following position :
• Adjust the angle of the seatback so that it is
in an upright position and your back comes
in full contact with it whenever the vehicle is
moving.
• Adjust the head restraint so that the upper
edge is as even with the top of your head as possible but not lower than eye level and so
that it is as close to the back of your head as
possible
¢ page 101.
• Keep both feet flat on the floor in front of
the front passenger seat.
• Fasten and wear safety belts correctly
t::;> page 110.
For detailed information on how to adjust the
front passenger's seat, see
¢ page 66.

Safety belts
General notes
Always wear safety belts!
Wearing safety belts correctly saves lives!
This chapte r exp lains why safety be lts a re nec­
essary, how they work and how to adjust and
wear them correctly.
~ Read a ll the informat ion that fo llows and
heed all of the inst ruct ions and WARNINGS.
A WARNING
Not wearing safety belts or wearing them
imp roperly increases the risk of ser ious
personal in jury and death .
- Safety belts are the sing le most effective
means availab le to red uce the r isk of se­
rious injury and death in a utomob ile acci­
dents . For your prot ecti on and that of
yo ur passenge rs, always co rrec tly wear
sa fe ty bel ts when the ve hicle is mov ing.
- P re g nant women, injured, or physically
impa ired perso ns must also use safe ty
belts. L ike a ll vehicle occup ants, they are
more like ly to be ser ious ly injure d if they
do not wea r safety be lts . The best way to
protect a fet us is to protect the mother -
thro ughout the entire pregnancy.
Number of seats
Your Audi TT Roadster has two seating posi­
tions. Each seat ing pos ition has a safety be lt.
A WARNING
Not wearing safety belts or wearing them
improper ly increases the risk of ser ious
personal in jury and death.
- Never st rap more than one person, in­
clu ding small ch ild ren, into any belt. It is
especially dangerous to place a safety
belt over a child s itting on yo ur lap.
- Never let mo re people ride in the ve hicle
t h an t he re a re safety be lts ava ilable.
Sa fety belts 107
- Be s ure everyone riding in the vehicle is
properly restrained w ith a separate sa fe­
ty belt or child restra int.
4 Safety belt warning light
Your vehicle has a warning system for the
driver and front seat passenger to remind you
about the importance of buckling-up.
Fi g. 1 10 Safety be lt warn ing lig ht in the instr ume nt
cl uster -enla rged
Befor e driv ing off, always :
~ Fasten your sa fe ty belt and make su re you
wear it p roperly.
~ Make s ure that yo ur passenge rs a lso buck le
up and properly wear their safety be lts.
~ Protect childre n with a child rest raint sys-
tem appropriate for the size and age .
The wa rning light . in the instrument cluster
li ghts up w hen the ig nit ion is switched on as a
remi nder to fasten the safety belts. In addi­
tion , you will hear a warning tone for a certa in
per iod of t ime .
Fasten your safety belt and make sure that
your passengers also properly put on their saf ety belts .
A WARNING
-Safety belts are the s ingle most effect ive
means ava ilable to reduce t he risk of se­
rio us i nju ry and de ath in au tomobile a cci­
dents . Fo r yo ur pro tection and tha t of
your passen gers, a lways correctly wear
safety belts when t he ve hicl e is moving .
- Fail ure to p ay att ent io n t o the wa rni ng
lig ht that come on , could lead to person ­
a l injury . •
•

During normal driving the belt lets you move
freely.
Safety belt pretensioners
The safety belts are equipped with a belt p re­
tensione r that helps to t igh ten the safety be lt
and remove s lack when the pretensione r is ac­
tivated. The function of the pretensioner is monitored by a warning light
¢ page 16.
Switchable locking feature
Every safe ty belt excep t the one on the driver
seat is eq uipped w ith a switchab le locking fea­
ture that
mu st be used when the safety belt is
used to attach a child seat . Be s ure to read the
important informat ion about th is f eature
c:;, page 144.
A WARNING
Improperly positioned safety belts can
cause serious injury in an accident
¢ page 111, Safety belt position .
-Safety belts offer optimum protection
only when the seatback is upright and
belts are properly positioned on the
body .
-
-Never attach the safety belt to the buck ­
le for another seat . Attach ing the belt to
the wrong buckle will reduce safety belt effect iveness and ca n cause seri ous per­
sonal in jury.
- A passenger who is no t properly rest rain­
ed can be se rio usly inju red by the safety
belt itself when it moves from the stron­
ger parts of the body into critical areas
like the abdomen .
- Always lock the convert ible locking re ­
tractor when yo u are secur ing a chi ld
seat in the vehicle
c:;, page 146 .
Safety belts 111
Safety belt position
Correct belt position is the key to getting
maximum protection from safety belts .
Fig . 1 16 Head restra int a nd safety be lt pos it io n as
see n fr om t he side
Use the height adjustment to change the posi­
tion of the shoulder straps of the fro nt seat
safety belts .
A WARNING
Imp roperly posit ioned safety be lts can
cause ser ious persona l injury in an acci­
dent.
- The shou lder belt portion of the safety
be lt must be posi tioned over the midd le
of the occupant's shoulder and never
across the neck or throat.
- The safety be lt must lie fla t and sn ug on
the occupant's upper body¢
fig. 116.
Pull on the belt to tighten if necessary.
-
- The lap be lt po rtion of the safety belt
must be posit ioned as low as possib le
across pelvis and never over the abdo ­
men. Make sure the belt lies flat and
snug ¢
fig. 116 . Pull on the belt to tight­
en if necessary .
- A loose-fitting safety belt can cause seri­
ous injuries by shifting its pos it ion on
your body from the strong bones to more
vulne rable , soft tissue and cause ser ious
in jury .
- Always read and heed all WARNINGS and
other important information
¢page 109.

Safety Standard 208 as applicable at the time
your vehicle was manufactured.
The Standard requires the front a irbag on the
passenger side to be t urned off ("sup­
pressed") if a child up to about one year of
age restrained in one of the rear -facing or for­
ward -facing infant restra ints listed in Federal
Motor Vehicle Safety Standard 208 with wh ich
the Advanced Airbag System in your vehicle
was certified has been installed o n the front
passenger seat. Fo r a listing of the child re­
straints that were used to certify compliance
with the US Safety Standard
q page 138.
The PASSENG ER AIR BAG OFF light in the in­
strument panel tells you when the front Ad­
vanced A irbag on the passenger side has bee n
turned off by the e lectronic control u nit.
Each t ime you turn on the ignition, the
PAS ­
SENGER AIR BAG OFF
l ight w ill come on for a
few seco nds and:
- will stay on if the front passenger seat is not
occupied,
- will stay on if there is a small child or ch ild
restraint on the front passenger seat,
- wi ll go off if the front passenger seat is oc­
cupied by an adult as registered by the
weight-sensing mat
q page 125, Monitor­
ing the Advanced Airbag System.
The PASSENGER AIR BAG OFF light comes on
when the control un it detects a total weight
on the front passenger seat that requires the
front airbag to be tu rned off .
If the total weight on the front passenger
seat is more than that of a typical 1 year-old
chi ld but less than the weight of a sma ll
ad ult, the front airbag on the passenge r side
can dep loy (the
PASSENGER AIR BAG OFF
light does not come o n). If the PASSENGER
AIR BAG OFF
l igh t does not come on, the
front airbag on the passenger side has not
been turned off by the electronic control unit
and can dep loy if the control u nit senses an
impact that meets the conditions stored in its
memory.
For example , the airbag may deploy if :
Airbag system 117
- a small ch ild that is heav ie r th an a typical 1
year -old chi ld is o n the front passenger seat
(regard less o f whether the child is in one o f
the child safety seats listed
q page 138), or
- a child who has outgrown child restraints is
on the front passenger seat.
I f the front passenger ai rbag is turned off, the
PASSENGER AIR BAG OFF light comes on in
the instr ument cluster and stays on .
T he front airbag on the passenge r side may
not deploy (t he PASSENGER AIR BAG OFF
light does not illuminate a nd stay lit) even if a
small ad ult o r teenager, or a passenger who is
not sitting upright with their back against a
non-recl ined backrest w ith their feet on the
vehicle floor in front of the seat is on the front
passenger seat ¢
page 99, Proper seating po ­
sition for the driver.
If the front passenger airbag dep loys, the
Federa l Standard requ ires the airbag to meet
t h e "low risk" dep loyment criteria to reduce
t h e risk of injury th rough inte ract ion w ith the
airbag. "Low risk" deployment occurs in those
crashes that ta ke pla ce at lower dece le rat io ns
as de fined in the e lectronic co ntrol unit
¢ page 1 26, PASSENG ER AIR BAG O FF light.
Always remember, a c hild safety seat o r in fant
car rie r in st alled on the fron t seat may be
stru ck and kno cked ou t of po sitio n by the rap­
i dly i nflat ing passenger 's airbag in a fronta l
collision. The ai rbag co uld great ly red uce the
effectiveness of the chi ld restraint and even
seriously in jure the child during inflation.
For t his reason, and because the back seat is
the safest place for c hildren - when proper ly
rest rained according to their age and size -we
strong ly recommend that chi ldren a lways sit
i n the back seat¢
page 136, Child Safety .
A WARNING
-
A child in a rearward-facing ch ild safety
seat ins talled on the fron t passenger seat
will be ser io us ly injure d and can be killed if
the front airbag inflates -even with an Ad-
v anc ed Airbag System . ..,_
•
•