ESP AUDI TT ROADSTER 2016 Owner's Guide

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
......
0
,.....
Vl
CX) consumed,
but only a small amount is supplied.
The situation is also critical if electrical equip­
ment is in use when the engine is not running. In
this case power is consumed when none is being
generated.
In these situations you will be aware that the
power management system is intervening to con­
trol the distribution of electrical power.
When the vehicle is parked for long periods
If you do not drive your vehicle for a period of
several days or weeks, the power management
will gradually shut off the on-board systems one
by one, or reduce the amount of current they are
using. This limits the amount of power consumed
and helps to ensure reliable starting even after a
long period. Certain convenience features, such
as remote control unlocking, may not be availa­
ble. These functions will be restored when you
switch on the ignition and start the engine.
With the engine switched off
If you listen to the radio or use the other info­
tainment functions when the engine is not run­
ning, this will discharge the vehicle battery.
The infotainment display will show a warning
message before the battery power drops to a lev­
el where the starting ability is impaired. This
message warns you that the system you are using
will soon be switched off automatically. You
should therefore start the engine if you wish to
continue using the system.
When the engine is running
Although the alternator generates electrical
power, the vehicle battery can still become dis­
charged while the vehicle is being driven. This can
occur when a lot of power is being consumed but
only a small amount supplied, especially if the
vehicle battery is not fully charged initially.
To restore the necessary energy balance, the sys­
tem will then temporarily shut off the electrical
components that are using a lot of power, or re­
duce the current they are consuming. Heating
systems in particular use a large amount of elec­
trical power. If you notice, for instance, that the
seat heating* or the rear window heater is not Intelligent
technology
working, they may have been temporarily switch­
ed off or regulated to a lower heat output. These
systems will be available again as soon as suffi­
cient electrical power is available.
You may also notice that the engine runs at a
slightly faster idling speed. This is quite normal,
and no cause for concern. The increased idling
speed allows the alternator to meet the greater
power requirement and charge the vehicle bat­
tery at the same time.
Information saved in the
control units
The vehicle is fitted in the factory with electronic
control units that, among other things, control
the engine and the gearbox. The control units al­
so monitor the exhaust system and the airbags.
The control units continually analyse data rele­
vant to the vehicle while you are driving. In the
event of faults or anomalies in the vehicle data,
only these data are saved. As a rule, faults are
shown by the warning lamps in the instrument
cluster.
Data saved in the control units can only be read
and analysed with special equipment.
A qualified workshop is only able to recognise
and deal with faults by using the relevant saved
data. Among other things, the saved data may
contain the following information:
- Data relating to the engine and the gearbox
-Speed
- Direction of travel
- Braking force
- Seat belt warning system data
The control units installed will not under any cir­
cumstances record conversations in the vehicle.
Event data recorder
Your vehicle is not equipped with an event data
recorder.
In an event data recorder, information about
the
vehicle is temporarily saved. In the event of an
accident, you can therefore obtain detailed infor-
mation about the course of events. On vehicles ...,.
119

Downloaded from www.Manualslib.com manuals search engine Multi
Media Interface
signals (such as the sirens of police and emer­
gency vehicles) clearly -failure to do so could
result in an accident.
(© Note
If the engine is switched off and the vehicle
battery charge level is low, the MMI system
will be switched off automatically.
How to use the MMI
Selecting and confirming a function
Fig. 125 How to use the rotary pushbutton
Selecting and confirming a function in a
menu/list
... To select a function: Turn the rotary pushbut­
ton (D ¢ Fig. 125 to the desired function (e.g.
setting a frequency) .
... To confirm the select ion: Press the rotary
pushbutton @¢ Fig. 125.
Returning to the previous function level
... Press the I
B
A CK
I button
0 ¢ page 121,
Fig. 123.
122 Calling
up the main menu/menu
Fig. 126 Illustration: Main menu
Calling up the main menu
... Press the button marked I MENU I®
¢ page 121, Fig. 123. The MMI menus (e.g. Ra­
dio) will be displayed ¢ Fig. 126. You can then
use the rotary pushbutton to select and con­
firm a function.
Calling up a menu directly
... Press the corresponding button to call up me­
nus directly ®¢ page 121, Fig. 123 in the di­
rection of the menu you require (e.g. !RA
DIO!).
You can then use the rotary pushbutton to se­
lect and confirm a function.

Downloaded from www.Manualslib.com manuals search engine Multi
Media Interface
Speller for Letters/numbers
Fig. 135 Illustration: Speller for letters/numbers
You can use the speller for letters/numbers to
enter letters, numbers and characters in the
MMI. This option is available while the entry field
@ is active ¢ Fig. 135.
- To call up/close the speller for letters/num­
bers: Push the rotary pushbutton upwards/
downwards while the entry field is active. Or:
Select the right control button > Open speller/
Close speller.
- To enter a letter/number: With the selection
line activated, turn the rotary pushbutton @
¢ Fig. 135 to select the desired letter/number.
Press the rotary pushbutton to confirm the let­
ter/number. Your entry will appear in the entry
field @. When you have entered all characters,
select and confirm I LIST !@ .
Or: Push the rota­
ry pushbutton downwards.
- To enter diacritics (e.g. a,�. ii, o)*: With the
selection line activated, turn the rotary push­
button to select a letter @¢ Fig. 135. To open
the corresponding set of diacritics, press and
hold the rotary pushbutton. Turn the rotary
pushbutton to select a diacritic while in the
character selection line@¢ Fig. 135. Press the
rotary pushbutton to apply the diacritic. To
close the set of diacritics without selecting a
character, press and hold the rotary pushbut­
ton again. Or: Select and confirm la ou lQ)
¢ Fig. 135. Select and confirm a diacritic.
-To delete a character: Select and confirm �@
¢Fig. 135. To delete all characters in the entry
128 field,
select� @¢ Fig. 135 and press and
hold the rotary pushbutton until all characters
have been deleted.
- To enter a special character: Select and confirm
! !&?! @¢Fig. 135 or!123! @. Use the speller
for numbers to select and confirm the special
character desired (such as a hyphen or full
stop).
- Input help: In some cases (such as in the navi­
gation system*), the system will suggest a
word* to complete your entry while you are still
making it@ ¢ Fig. 135. You can confirm the
word by pushing the rotary pushbutton up­
wards.
- Results list: In some cases (such as in the direc­
tory), the system will switch to the results list
@ ¢Fig. 135 automatically. Select and confirm
a suggestion from the list.
Requirement: The entry field@¢ Fig. 135 must
be active.
- To switch between the speller and the MMI
touch pad*: The handwriting recognition fea­
ture is automatically activated for the MMI
touch pad*, which means you can simply start
writing.
Overview of the symbols in the speller
The symbols of the speller for letters/numbers
are explained in the following table:
�

Downloaded from www.Manualslib.com manuals search engine Speech
dialogue system
the operating instructions for your mobile
phone.
- AUDI AG only enables you to access your
mobile phone's speech dialogue system and
accepts no responsibility for the content
and commands of the external speech dia­
logue system.
140

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,..... Read
1
)
You can have the MMI read an opened text mes­
sage to you.
Text message settings*
Activate Text message notifications to have a no­
tification displayed when a new text message is
received. An envelope symbol 121 is displayed in
the status line of the infotainment display if
there are any new text messages.
The number of your mobile network service pro­
vider's Text message centre is displayed. If no
number has been stored, you can enter the num­
ber of the text message centre. For more infor­
mation, contact your service provider.
Conne ction manager
Refer to¢ page 213.
Telephone settings
Refer to ¢page 155.
� Note
Messages deleted using the MMI are also au­
tomatically deleted on the mobile phone.
E-mail*
Applies to: mobile phones with Bluetooth Message Access
Profile
Depending on your mobile phone, you may be
able to send and receive e-mails via the MMI.
Important: Your mobile phone must have mes­
sage access rights activated in its Bluetooth set­
tings (MAP -Message Access Profile) and must be
connected to the MMI ¢ page 142. Please refer
to the operating instructions for your mobile
phone to find out whether it supports this func­
tion.
.,. Select: IM E
N u
I button > Telephone > left con­
trol button > E-mail (myPhone)/E-mail (addi­
tional phone)*.
N
......
0
,.....
� 1}
Not available in all langu ages. Telephone
Write new e-mail
- To
use
a template: Select and confirm the tem-
plate you require from the list.
- Enter one or more recipients.
- Select and confirm Send.
lnbox
All the e-mails you have received are displayed.
Sent
All the e-mails you have sent are displayed.
Outbox
All the e-mails to be sent are displayed.
Drafts
All the e-mails which have been stored but not
yet sent are displayed.
CD CAUT
ION
Please always observe the information ¢(Din
Wi-Fi hotspot on page 166.
((D) Note
- For more information on which mobile
phones are supported, please go online
(e.g. www.audi.com/bluetooth) or contact
an Audi dealer.
- Please connect your mobile phone to the ve­
hicle's Wi-Fi hotspot* so that the e-mail app
on your mobile phone retains access to the
Internet. This helps to ensure that e-mails
can be sent and received. If you cannot re­
ceive e-mails despite being successfully con­
nected, please contact your e-mail service
provider or your mobile network provider.
Message options
Applies to: mobile phones with Bluetooth Message Access
Profile
.,. Select: I M
ENU
I button >Telephone > left con­
trol button > E-mail (myPhone)/E-mail (addi­
tional phone)* > lnbox/Sent/Outbox > right
control button.
...,
151

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
......
0
,.....
Vl
CX) device
1/USB device 2 >All> Start import/
Start export.
- To import contacts from your myAudi ac­
count l
): Select and confirm Import contacts >
myAudi account. Enter your myAudi user data.
You must have a myAudi account before you can
import contacts from the myAudi account. You
only have to enter your myAudi user data/myAudi
PIN once. When you store a vehicle in your myAu­
di account, you will receive the myAudi PIN in the
account.
- Please always note the information in the
chapter¢ page 167, Notes on Audi con­
nect.
- For more information on the myAudi ac­
count, please refer to my.audi.com.
- The imported contacts are stored in the lo­
cal memory of the directory you are using.
- You can import up to 1000 contacts. You
can call up the memory capacity of the di­
rectory any time¢ page 156.
- Never store important data on SD cards or
USB mass storage devices. Audi shall not ac­
cept any liability whatsoever for the loss of
data or media.
- It is not possible to export contacts which
have been downloaded from a mobile
phone.
- There should be no files or directories on
the storage medium other than the contacts
you wish to import.
Settings Telephone settings
Applies to: vehicles with telephone
� Select: I MENU
I button
>Telephone > right con­
trol button > Telephone settings.
1} The conditions for using Audi connect services* must be
met and you must have created a myAudi account at
my.audi.com, added a vehicle to the account and stored
contacts. Telephone
Call options*
Call forward: Forwarding of incoming calls to
your mailbox or to another phone number can be
switched on/off. You can use Check status to
check whether this function is activated or deacti­
vated.
Call waiting: If this option is activated �, you
will be informed of incoming calls when you are
on the phone. You can use Check status to check
whether this function is activated or deactivated.
Transmit caller ID: Sending your telephone num­
ber in outgoing calls can be activated/deactiva­
ted. With the Network-dependent option, the
setting agreed in your mobile network service
contract will be used. The settings apply only to
the Telephone menu in the MMI system. When
the Bluetooth connection has been terminated,
the settings of your mobile phone apply. You can
use Check status to check whether this function
is activated or deactivated.
Telephone mode*
On vehicles with a car telephone kit, you can
choose between three different telephone modes
to optimise the network response:
-Automatic: The car telephone automatically
switches between the GSM (2G), UMTS (3G)
and LTE networks. This depends on the net­
work, the network reception, and the position
of the vehicle. In this mode, there might be re­
strictions when using Google Earth or Wi-Fi.
- Telephony optimised: The car telephone kit
registers with the GSM network (2G). In this
mode, the reception is prioritised for making
and receiving calls. There may be restrictions
when using Google Earth or Wi-Fi.
- Data service optimised: The car telephone reg­
isters with the GSM (2G), UMTS (3G) or LTE net­
work. This depends on the network, the net­
work reception, and the position of the vehicle.
In this mode, the reception is prioritised for the ...,
155

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
......
0
,.....
Vl
CX) Export
contacts
Refer to ¢page 154, Importing/exporting con­
tacts.
Download directory
To update the contacts in the MMI, you can
download the contacts from your mobile phone
manu ally. Depending on the mobile phone you
are using, the Bluetooth connection may have to
be disconnected and re-established before you
can update the contacts.
Hiding contacts without a number
If this function is switched on� and if no num­
ber has been stored for a contact, the contact is
displayed greyed out in the direc tory.
Seat belt microphone
Applies to: vehicles with seat belt microphone
The seat belt microphone is ideally positioned
for the best possible communication quality
when using the handsfree system, irrespective of
your height and sitting position.
Fig. 149 Seat belt microphone Telephone
The seat belt microphone is activated as soon as
you put on the seat belt. Make sure that the mi­
crophones are on the outside of the seat belt
¢Fig. 149.
When the driver's seat belt is unbuc kled, the sys­
tem switches from the seat belt microphone to
the roof microphone.
@ Note
- If you switch off* the passenger's airbag,
the passenger's seat belt microphone is de­
activated even if the belt is buckled.
- If the opening for a microphone is dirty, this
can impair the quality of handsfree commu­
nication. In this case, clean the seat belt mi­
crophone using a fine brush.
157

Downloaded from www.Manualslib.com manuals search engine Audi
connect
... Select: Online news > desired news feed> a
headline.
{Q')) Note
If you have not yet subscribed to any personal
news feeds in your myAudi account, pre-con­
figured news feeds will be shown.
Twitter
Applies to: vehicles with Audi connect
You can access the most important functions of
your Twitter account via the MMI.
Important: You must have linked your myAudi account to
Twitter. For more information, please refer to
my.audi.com.
You must have linked your vehicle to myAudi
¢page 162.
... Select Twitter > left control button > function
desired (e.g. Trends).
You can choose the following categories in the
Twitter menu:
- My tweets: New tweets and tweets you have
composed are listed.
- Home: All the tweets from people you are fol­
lowing are displayed.
- Trends: Topics currently being favoured for dis-
cussion within a particular country.
Different functions will be available depending
on the Twitter category you choose:
- New tweet: You can send a new tweet with the
help of ready-made templates or text blocks
personalised in your myAudi account.
- Refresh: The selected Twitter function is upda­
ted.
- Favourite: You can "favourite" a tweet to show
that you like it.
- Retweet: You can repost a tweet to share it
with other people.
164 (I))
Note
- For more information on how to connect
your myAudi account to Twitter, please see
my.audi.com.
- Further settings (such as your account, lan­
guage, Tweet privacy, and location settings)
cannot be changed in the MMI. If you wish
to change anything in these menus, please
do so on the Twitter website itself.
- Further information on the individual tem­
plates can be found at my.audi.com.
- You can only connect one Twitter account to
your myAudi account.
- Audi connect enables you to access the Twit­
ter service. Audi cannot guarantee that
these services will be available indefinitely;
this is the responsibility of Twitter.
Audi connect services in the navigation
system
Applies to: vehicles with navigation system and Audi connect
The following Audi connect services are currently
available:
- Navigation with Google Earth and Google
Street View ¢page 181.
- Online point of interest search with speech
dialogue system (e.g. restaurants): For plan­
ning a route via the MMI control console and
the speech dialogue system ¢page 133.
-Adding a destination to your MMI via your
my Audi account ¢ page 173 or Google Maps
¢page 181.
- Online traffic information*: Up-to-the-minute
reception of information on accidents, road­
works and other incidents ¢page 182.
- myAudi special destinations*: Your personal
special destinations can be imported to your
MMI via an SD card.
- Map update*: Navigation map updates can be
imported to your MMI using an SD card.
(D) Note
- The Audi connect map update service using
an SD card allows you to find out which soft­
ware version is installed in your vehicle. You
can then check whether a new version is
�

Downloaded from www.Manualslib.com manuals search engine Audi
connect
Netwo rk search*
A List of the Wi-Fi networks available near you is
displayed.
Connection to personal hotspot1
)
The Wi-Fi hotspot of the MMI is activated. The
MMI can establish an Internet connection to a
personal Wi-Fi hotspot (e.g. smartphone). You
can search for your personal hotspot and connect
to the MMI using Network search. For more in­
formation, please refer to ¢ page 161.
This mode is not available if your own SIM card is
inserted in the SIM card reader.
A WARNING
- Do not allow the features of the Wi-Fi hot­
spot to distract you from watching the traf­
fic -taking your eyes off the road can cause
an accident.
- Mobile devices, tablet and laptop computers
and devices of a similar weight can only be
operated safely when the vehicle is station­
ary. Like any loose object, they can be cata­
pulted through the vehicle in an accident
and cause serious injuries. Always make sure
that such devices are securely stowed while
you are driving.
- No Wi-Fi devices may be used in the areas
around the airbags while the vehicle is being
driven. Please also observe the safety warn­
ings in the chapter on¢ page 235.
- Depending on the configuration of the Wi-Fi
device you are using (refer to the operating
manual of your Wi-Fi device for more de­
tails), the SIM card of the device may be
used in certain
cases
to provide the data
connection for Internet-supported apps and
services which use the MMI Wi-Fi hotspot.
Depending on your network provider, you
may be charged for this service, especially if
you are using the system abroad. We there­
fore strongly recommend that you use an
unlimited data plan. For more information,
l l
Not available in all markets.
166 contact
your service provider. Some exam­
ple cases are described below:
- Data plan expired/used up
- Data plan not valid abroad
- SIM card in the card reader* is not a data
SIM card
- SIM card in the card reader* is defective/
not valid
- Network is switched automatically due to
a low signal strength/data rate of the Wi­
Fi hotspot, the eSIM* or the SIM card in
the card reader*
- Connection to Wi-Fi hotspot interrupted
- Please note that it is your responsibility to
. take
precautions regarding data protection,
anti-virus protection and protection against
loss of data on mobile devices used to con­
nect to the Internet via the Wi-Fi hotspot.
1 Note
- You might require a separate mobile phone
contract with extra costs before you can use
the Wi-Fi hotspot. For more information,
contact your service provider.
- In vehicles without Audi connect*, the Wi-Fi
hotspot can only be used for the Wi-Fi audio
player*. A data connection to the Internet
cannot be established.
- Further information can be found on the In­
ternet at www.audi.com.
Configuring the data
connection
Applies to: vehicles with Audi connect
You must configure a data connection before you
can use Audi connect services.
� Select: I MENU
I button > right control button >
Connection manager.
� Select: right control button > Online settings >
Data connection settings.
You can select when you would Like the system to
establish an Internet connection in the Data con­
nection settings menu. The online connection is �

Downloaded from www.Manualslib.com manuals search engine severed
automatically when data packets are no
longer required.
The following options are available:
Connection setup
- with request: A data connection will only be es­
tablished on request.
- without request: A data connection will be es­
tablished automatically for the use of Audi con­
nect services.
- never: A data connection will not be establish­
ed. It is then not possible to call up Audi con­
nect services.
When a data connection has been established, a
symbol indicating the type of connection and the
signal strength will appear in the status line of
the infotainment display®/@ ¢ page 130,
Fig. 137.
You can cancel an active data connection manual­
ly by setting the Connec tion setup option to nev­
er.
Data roaming
The Data roaming function is deactivated when
the vehicle leaves the factory. Data roaming
must be activated (�) before you can use a data
connection abroad. This setting is saved for the
current SIM card/the mobile phone currently
connected.
Audi connect (MMI)
With this function, you can allow or deny the use
of Audi connect services if the connection is set
to no request or if requested.
Connection settings
Depending on the SIM card used, the connection
may be configured automatically. However, these
settings can be changed. For more information,
contact your service provider.
-APN: The system access point depends on your
mobile network service provider and is assigned
automatically.
� -
User name: The user name for your on line pro-
� file is assigned by your mobile network service
,.....
� provider.
0
,.....
Vl
CX) Audi
connect
- Password: The password for your on line profile
is assigned by your mobile network service pro­
vider.
To store changed connection settings: Press the
I BACK!
button.
Reset configuration
An online profile is created and configured auto­
matically. The Connection settings you have
changed manually are reset to the default set­
tings.
@ Note
- According to the factory settings, the data
connection will be interrupted initially when
you travel abroad to protect you from unex­
pected roaming charges. If you want to use
Audi connect services abroad, you must first
activate the Data roaming option.
- For more information on roaming charges,
contact your service provider.
- Further information can be found on the In­
ternet at www.audi.com.
Notes on Audi connect
Audi connect services
Applies to: vehicles with Audi connect
{(D) Note
- Audi connect services are only available with
an existing mobile phone contract (or one
set up separately) and if you are in an area
with mobile phone network coverage. De­
pending on your mobile phone tariff, you
may be charged for receiving data packets
on line, especially if you are using the sys­
tem abroad. Because of the high level of da­
ta usage, we strongly recommend using an
unlimited data plan.
- The mobile phone standard LTE* is not
available for use in all countries. For further
information, please consult an Audi dealer
or your mobile network service provider.
- In order to use Audi connect services, you
will need a mini SIM card with a data op­
tion; to use LTE*, the SIM card will also
need to have an LTE data option.
167