CADILLAC DTS 2010 1.G Owners Manual

It is recommended that the vehicle is taken to yourdealer/retailer for service if the headlamps need to bere-aimed. It is possible however, to re-aim theheadlamps as described.
Notice:To make sure the headlamps are aimedproperly, read all the instructions before beginning.Failure to follow these instructions could causedamage to headlamp parts.
The vehicle should:
•Be placed so the headlamps are 25 ft. (7.6 m) from
a light colored wall.
•Have all four tires on a level surface which is level
all the way to the wall.
•Be placed so it is perpendicular to the wall.
•Not have any snow, ice, or mud on it.
•Be fully assembled and all other work stopped while
headlamp aiming is being performed.
•Be normally loaded with a full tank of fuel and one
person or 160 lbs (75 kg) sitting on the driver seat.
•Have all tires properly inflated.
•Have the spare tire is in its original location in the
vehicle.
Headlamp aiming is done with the vehicle’s low-beamheadlamps. The high-beam headlamps will be correctlyaimed if the low-beam headlamps are aimed properly.
To adjust the vertical aim:
1. Open the hood. SeeHood Release on page 6-11for more information.
2. Find the center line running through the lens of theheadlamp.
3. Record the distance from the ground to the centerline running through the lens of the headlamp.
6-41

4. At a wall, measure from the ground upward (A) tothe recorded distance from Step 3 and mark it.
5. Draw or tape a horizontal line (B) the width of thevehicle at the wall where it was marked in Step 4.
Notice:Do not cover a headlamp to improve beamcut-off when aiming. Covering a headlamp maycause excessive heat build-up which may causedamage to the headlamp.
6. Turn on the low-beam headlamps and place apiece of cardboard or equivalent in front of theheadlamp not being aimed. This should allow onlythe beam of light from the headlamp beingaimed to be seen on the flat surface.
7. Locate the vertical headlamp aiming screws. Theyare located under the hood near each headlampassembly. First lift the flap to access either of them.Each one is the top outboard screw by the “ V” on thecover panel next to the aiming flap.
The adjustment screw can be turned with a 6 mmhex wrench.
8. Turn the vertical aiming screw until the headlampbeam is aimed to the horizontal tape line. Turn itclockwise or counterclockwise to raise or lower theangle of the beam.
The top edge of the cut-off should be positioned atthe bottom edge of the horizontal tape line.
6-42

9. Make sure that the light from the headlamp ispositioned at the bottom edge of the horizontal tapeline. The lamp on the left (A) shows the correctheadlamp aim. The lamp on the right (B) shows theincorrect headlamp aim.
10. Repeat Steps 7 through 9 for the oppositeheadlamp.
Bulb Replacement
It is recommended that all bulbs be replaced by yourdealer/retailer.
High Intensity Discharge (HID)
Lighting
{WARNING:
The low beam high intensity discharge lighting
system operates at a very high voltage. If you try to
service any of the system components, you could
be seriously injured. Have your dealer/retailer or a
qualified technician service them.
The vehicle may have HID headlamps. After an HIDheadlamp bulb has been replaced, you may notice thatthe beam is a slightly different shade than it wasoriginally. This is normal.
6-43

Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected for wearor cracking. SeeScheduled Maintenance on page 7-3for more information on wiper blade inspection.
Replacement blades come in different types and areremoved in different ways. Here is how to remove thewiper blade:
1. Turn the engine off.
2. Lit the windshield wiper arm and blade away fromthe windshield.
3. Pull the clip up from the blade connecting point andpull the blade assembly down toward the windshieldto remove it from the wiper arm.
4. Install the new wiper blade onto the wiper arm andfirmly press down on the clip to snap it into place.
6-44

To remove and replace the wiper blade element:
1. The wiper blade element has two notches at oneend which are engaged by the bottom claw set ofthe wiper blade. At the notched end of the wiperblade, pull the wiper blade element from the wiperblade assembly.
2. Replace the element by starting at the heel end ofthe wiper blade, which is the end nearest to thebase of the wiper arm, and slide the wiperblade element, notched end last, into the wiperblade claw sets.
3. Engage the last claw into the notched end of thewiper blade element by squeezing the wiper bladeelement at the notched area, and push the wiperblade element so the claw fits into the notch.
4. Be sure the two wiper blade element notches areengaged by the last claw set and all the otherclaws are properly engaged in the slots of the wiperblade element on both sides.
A. Correct Installation
B. Incorrect Installation
For the proper type and size windshield wiper blades,seeMaintenance Replacement Parts on page 7-10.
6-45

Tires
Your new vehicle comes with high-quality tiresmade by a leading tire manufacturer. If you everhave questions about your tire warranty and whereto obtain service, see your vehicle Warrantybooklet for details. For additional information referto the tire manufacturer.
{WARNING:
•Poorly maintained and improperly used
tires are dangerous.
•Overloading your tires can cause
overheating as a result of too muchflexing. You could have an air-out and aserious accident. SeeLoading theVehicle on page 5-18.
WARNING: (Continued)
WARNING: (Continued)
•Underinflated tires pose the same danger
as overloaded tires. The resultingaccident could cause serious injury.Check all tires frequently to maintain therecommended pressure. Tire pressureshould be checked when your tires arecold. SeeInflation - Tire Pressure onpage 6-54.
•Overinflated tires are more likely to be
cut, punctured, or broken by a suddenimpact — such as when you hit apothole. Keep tires at the recommendedpressure.
•Worn, old tires can cause accidents. If
your tread is badly worn, or if your tireshave been damaged, replace them.
SeeHigh-Speed Operation on page 6-56forinflation pressure adjustment for high speeddriving.
6-46

Tire Sidewall Labeling
Useful information about a tire is molded into itssidewall.
(A) Tire Size:The tire size is a combination ofletters and numbers used to define a particulartire’s width, height, aspect ratio, construction typeand service description. See the “Tire Size”illustration later in this section for more detail.
(B) TPC Spec (Tire Performance CriteriaSpecification):Original equipment tires designedto GM’s specific tire performance criteria havea TPC specification code molded onto the sidewall.GM’s TPC specifications meet or exceed allfederal safety guidelines.
(C) DOT (Department of Transportation):TheDepartment of Transportation (DOT) codeindicates that the tire is in compliance with theU.S. Department of Transportation Motor VehicleSafety Standards.
(D) Tire Identification Number (TIN):The lettersand numbers following the DOT code are theTire Identification Number (TIN). The TIN showsthe manufacturer and plant code, tire size,and date the tire was manufactured. The TIN ismolded onto both sides of the tire, althoughonly one side may have the date of manufacture.
Passenger Car Tire Example
6-47

(E) Tire Ply Material:The type of cord andnumber of plies in the sidewall and underthe tread.
(F) Uniform Tire Quality Grading (UTQG):Tiremanufacturers are required to grade tiresbased on three performance factors: treadwear,traction and temperature resistance. For moreinformation seeUniform Tire Quality Grading onpage 6-67.
(G) Maximum Cold Inflation LoadLimit:Maximum load that can be carried and themaximum pressure needed to support thatload. For information on recommended tirepressure seeInflation - Tire Pressure on page 6-54andLoading the Vehicle on page 5-18.
(A) Temporary Use Only:The compact spare tireor temporary use tire has a tread life ofapproximately 3,000 miles (5 000 km) and shouldnot be driven at speeds over 65 mph (105 km/h).The compact spare tire is for emergency use whena regular road tire has lost air and gone flat.SeeSpare Tire on page 6-90andIf a Tire GoesFlat on page 6-70.
Compact Spare Tire Example
6-48

(B) Tire Ply Material:The type of cord andnumber of plies in the sidewall and under thetread.
(C) Tire Identification Number (TIN):The TireIdentification Number (TIN). The TIN showsthe manufacturer and plant code, tire size, anddate the tire was manufactured. The TIN is moldedonto both sides of the tire, although only oneside may have the date of manufacture.
(D) Maximum Cold Inflation LoadLimit:Maximum load that can be carried and themaximum pressure needed to support thatload. SeeInflation - Tire Pressure on page 6-54andLoading the Vehicle on page 5-18.
(E) Tire Inflation:The temporary use tire orcompact spare tire should be inflated to 60 psi(420 kPa). For more information on tire pressureand inflation seeInflation - Tire Pressure onpage 6-54andSpare Tire on page 6-90.
(F) Tire Size:A combination of letters andnumbers define a tire’s width, height, aspect ratio,construction type and service description. Theletter T as the first character in the tire size meansthe tire is for temporary use only.
(G) TPC Spec (Tire Performance CriteriaSpecification):Original equipment tires designedto GM’s specific tire performance criteria havea TPC specification code molded onto the sidewall.GM’s TPC specifications meet or exceed allfederal safety guidelines.
6-49

(A) Tire Size:The tire size code is a combinationof letters and numbers used to define a particulartire’s width, height, aspect ratio, constructiontype and service description. See the “Tire Size”illustration later in this section for more detail.
(B) TPC Spec (Tire Performance CriteriaSpecification):Original equipment tires designedto GM’s specific tire performance criteria havea TPC specification code molded onto the sidewall.GM’s TPC specifications meet or exceed allfederal safety guidelines.
(C) Dual Tire Maximum Load:Maximum loadthat can be carried and the maximum pressureneeded to support that load when used in a dualconfiguration.
(D) DOT (Department of Transportation):TheDepartment of Transportation (DOT) codeindicates that the tire is in compliance with theU.S. Department of Transportation Motor VehicleSafety Standards.
(E) Tire Identification Number (TIN):The lettersand numbers following DOT code are the TireIdentification Number (TIN). The TIN showsthe manufacturer and plant code, tire size, anddate the tire was manufactured. The TIN is moldedonto both sides of the tire, although only oneside may have the date of manufacture.
Light Truck Tire Example
6-50