light CHEVROLET CAMARO 1967 1.G Chassis Workshop Manual

ELECTRICAL-BODY AND CHASSIS 12-3

Fig.
2 - T-3 Safety Aimer

wearing away the insulation due to vibration.

By referring to the wiring diagrams, circuits may be

tested for continuous circuit or shorts with a conventional

test lamp or low reading volt meter.

HEADLAMP ADJUSTMENT-

T-3 HEADLAMPS

CAUTION: Check and tighten radiator support

grille retaining bolts prior to attempting head-

lamp aiming. Distorted grille or supports in

this area will hinder proper aiming of head-

lamps. On Corvette models make sure head-

lamp panel is adjusted properly - refer to

"Headlamp Panel Travel Adjustment".

When aiming headlamps, vehicle should be filled to ca-

pacity with gas, oil, and water but no load. Tires should

be uniformly inflated to recommended pressure.

the T-3 Safety Aimer-Type B (fig. 2), is used for the

headlamp aiming description that follows. An adapter is

required with the Type B T-3 Aimer when adjusting the 7

inch headlamp used on the Chevy n vehicle.

1.
Drive vehicle onto selected aiming area. Bounce

vehicle several times and allow to settle.

2.
Remove headlamp bezels.

3.
Mount the T-3 Aimers on either the No. 1 or No. 2

pair of headlamps so that "the points of the headlamps

engage the smooth inner ring of the aimers.
HORIZONTAL

AIMING

SCREW

STRING OVER

"2R" ON AIMER ARM

Fig.
4—-Headlamp Horizontal Adjustment

NOTE:
In the dual headlamp installation, the

inboard unit is designated No. 1 and the outboard

unit is designated No. 2.

4.
Secure the aimers to the headlamp units by firmly

pressing knob at center of each aimer (fig. 3). Ro-

tate crossarms inboard to approximate horizontal

position.

NOTE:
Moisten suction cups slightly to obtain

maximum holding force.

5. With both aimers in place, knot both ends of elastic

string and, using slots provided, fasten string across

horizontal crossarms of each aimer.

6. Rotate both aimers so that the string just clears the

points on the crossarms.

HORIZONTAL ADJUSTMENT

7. a. Turn horizontal aiming screw, Figure 4, on left-

VERTICAL ADJUSTMENT SCREW

Fig.
3 - Installing Aimer on Headlamp Unit
Fig.
5 - Headlamp Vertical Adjustment

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-5

Fig.
8—Turning Level Adjusting Screw to Calibrate Aimer

HEADLAMP PANEL TRAVEL ADJUSTMENT

Corvette (Fig. 9)

The headlamp panel travel is limited by two adjusting

screws which are located on the arms of the shaft

mounted stop.
Fig.
9—Headlamp Panel Travel Adjusting Screw

1.
Raise hood and as a safety precaution install a bolt

through the hole in the hood support - secure bolt

with a nut.

2.
Adjusting screw (A) limits headlamp panel travel in

open position - adjust this screw so that mounting

face of panel is within 2 degrees of vertical in the

fully open position.

NOTE: Each headlamp operates independently

of the other, therefore individual adjustment is

required for each panel.

3.
Adjusting screw (B) limits headlamp panel travel in

closed position - adjust this screw so that panel is

flush to upper body panel in the fully closed position.

4.
Lock both screws by tightening lock nut against stop.

5.
Remove safety bolt as installed in Step 1 and close

the hood.

SERVICE OPERATIONS

FRONT LIGHTING

HEADLAMP REPLACEMENT (Figs. 10 and 13)

1.
On Corvette and Camaro Rally Sport models, rotate

the headlamp panel to the open position.

2.
Remove headlamp bezel retaining screws and remove

bezel. On Chevrolet, Chevelle and Camaro models

lift bezel to disengage retaining tabs from slots in

filler panel.

3.
On Chevy n models remove three retaining ring at-

taching screws. On other models disengage spring

from the retaining ring and remove two attaching

screws.

4.
Remove retaining ring, disconnect sealed beam unit

at wiring connector and remove the unit.

5.
Attach connector to replacement unit and position

unit in place making sure the number molded into the

lens face is at the top.

NOTE: In the dual headlamp installation the

inboard unit (NO. 1) takes a double connector, the
outboard unit (No. 2) takes a triple connector

plug.

6. Position retaining ring into place and install the re-

taining ring attaching screws and spring (as

applicable).

7.
Check operation of unit and install the headlamp

bezel.

PARKING LAMP REPLACEMENT

Bulb

1.
Remove two lens retaining screws and disengage lens

from housing.

2.
Replace bulb, check operation of lamp, reinstall lens

and retaining screws.

Lamp Housing

Chevrolet, Chevelle and Chevy II (Figs. 10 and 11)

1.
Disconnect lamp wire assembly in-line connector

from wiring harness.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-8

is inserted through radiator support opening.

Remove two screws retaining lamp assembly to

lower sheet metal.

Remove three screws retaining lamp assembly to

lender.

To replace lamp assembly, reverse removal proce-

dure and check operation of the unit.
is aligned with flat on pivot shaft. Install stop lock

bolt and torque bolt to 45-60 in, lbs. Make sure that

side-to-side panel alignment is not changed when in-

stalling and tightening the stop.

CAUTION: Do not exceed specified torque

when tightening stop lock bolt.

HEADLAMP PANEL REPLACEMENT-CORVETTE

Refer to Figure 13 for Panel Mounting details.

1.
Remove engine compartment hood as outlined in

Section 1.

2.
Actuate headlamp panel to the open position.

NOTE:
In the event headlamp motor is inop-

erative, manual positioning of the panel can be

accomplished by turning the knurled knob at in-

board end of motor. As an assist in manual

operation of panel, apply light hand pressure to

panel in desired direction of rotation.

3.
Remove positive lead from battery terminal.

4.
Remove headlamp bezel retaining screws and bezel.

5. Remove the sealed beam housing unit as an assem-

bly - disconnect sealed beam leads at harness con-

nector and remove connector from sealed beam

leads;
remove the housing-to-panel retaining screws

and remove housing unit and wiring from panel.

6. Remove motor from panel pivot shaft - see motor

removal procedure. Then remove the panel stop

from panel inboard pivot shaft, and disconnect switch

lead wires from panel, support-mounted motor

switch.

7. Remove the panel retaining bolt access hole plugs

from inside the panel then rotate panel as required

and remove the retaining bolts and slide supports

from ends of panel pivot shaft. Remove bearing, felt

seal, retainer and washer from inboard pivot shaft.

8. Remove panel from its location by alternately disen-

gaging pivots from their retaining slots and with-

drawing unit forward through opening in body (fig.

14).

9. Loosen alien screw in spacer and disassemble parts

from the panel outboard pivot shaft.

10.
Install washer, retainer, felt seal, bearing and

spacer, in that order, to panel outboard pivot shaft.

Do not tighten spacer on shaft at this time.

11.
Position panel in body opening and index panel pivot

shafts in retaining slots; then loosely install support

retaining bolts.

12.
Install washer, retainer, felt seal, bearing and sup-

port, in that order, to panel inboard pivot shaft, and

loosely install support retaining bolts. -

13.
Check side-to-side alignment of panel, making sure

that there is no panel-to-body contact; position

spacer snugly against bearing; then tighten spacer

seat screw to 30-50 in. lbs.

14.
Install stop on panel inboard shaft so that it rests

against bearing, being sure that index mark on stop
15.
Check and align panel to body as follows:

a. Tighten panel pivot support bolts snugly but still

allowing panel to" be moved by applying hand

pressure.

b.
Position panel to the closed position and align

with body so that all surfaces are flush.

c. With the panel in the closed position the outboard

access hole is aligned with the forward bolt head.

Tighten this bolt with the panel in the closed

position - access to bolt head can be obtained by

working through opening between the hood and

body.

d. Rotate panel to obtain access to each bolt head

and torque bolts to 100-140 in. lbs.

e. Connect switch lead wires to support-mounted

limit switch.

16.
Install seaLed beam housing unit and at the same time

position sealed beam lead wires through panel out-

board pivot shaft. Install housing unit retaining

screws and install lead wires in connector, making

sure to match colors between harness and connector.

17.
Install motor assembly - see motor replacement

procedure.

18.
Connect positive lead to battery terminal.

19.
Adjust headlamp panel as outlined under "Headlamp

Panel Travel Adjustment".

20.
Adjust headlamp aiming as outlined under "Headlamp

Adjustment".

21.
Install headlamp bezel and engine compartment

hood - refer to Section 1 for hood installation.

Fig.
14
- Headlamp Panel Removal (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-10

10.
To install, replace motor assembly, and reverse re-

moval procedure.

REAR LIGHTING SERVICE

TAIL, STOP AND DIRECTIONAL LAMPS

Bulb Replacement (Fig. 17)

1.
Disconnect lamp socket from rear of lamp unit and

remove bulb from socket.

NOTE:
Bulb removal on station wagon models

and Corvette requires, removal of the lens to

gain access to the bulb.

2.
Replace bulb and plug socket back into lamp housing.
Lamp Housing Replacement

Chevrolet, Chevelle Station Wagon,

Camaro and Chevy II (Fig. 17)

1.
Disconnect bulb socket from rear of lamp unit.

NOTE:
On station wagons remove lens to gain

access to lamp or screws securing lamp housing

to body.

2.
Remove nuts at rear of housing retaining lamp hous-

ing to vehicle body, remove housing from vehicle.

3.
Remove lens retaining screws or nuts, remove lens

and transfer to new housing unit.

4.
To install reverse removal procedure and check op-

eration of lamp unit.

HEADLAMP

WIRING ASSEMBLY
MOTOR

INSTALLATION

TO PARKING LAMP

TO RETR. HDLP. MOTOR

TO HEADLAMP
HEADLAMP

DOOR ASSEMBLY

Fig.
16- Headlamp Motor Installation (Comoro)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-11

CHEVELLE STATION WAGON

CHEVROLET STATION WAGON

CHEVELLE WAGON

CHEVROLET SEDAN

OPERATION

Bulb

Replacement

Lens

Replacement

Housing

Replacement
METHOD

Remove Lens (Outside)

Remove Socket (Inside Rear

Compartment)

Remove Retaining Screws (Outside)

Remove Housing and Disassemble

Remove From Outside (Retaining

Nuts in Rear Compartment

Remove From Inside

Remove From Outside (Retaining

Bolts Under Lens)

Lower Rear Bumper
BODY TYPE

Chevelle

X

X

X
Chevelle

35

X

X

X
Chevrolet

X

X

X
Chevrolet

35-45

X

i

•x

X
Camaro

F

X

-

X

X
Chevy II

X

X

X

X

Fig.
17 - Rear Lighting Composite (Exc. Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-12

NOTE:
Gasket must be carefully installed to

prevent body leaks.

Corvette (Fig. 18)

1.
Working at the underside of the body rear panel, dis-

connect the harness connector at the lamp assembly;

then remove the lamp assembly retaining nuts and

remove lamp assembly from recess in body panel.

NOTE:
Remove tail pipe extensions and rear

body valance panel to facilitate removal of the

outboard lamp assemblies.
2.
Position lamp assembly in body panel recess so that

studs are aligned with holes in panel.

3.
Position lamp assembly ground wire over stud; then

install remaining nuts and tighten securely.

4.
Install harness connector to lamp assembly and test

operation of light.

Bulb Replacement (Fig. 19)

1.
Remove lens retaining screws and disengage lens

from housing.

2.
Replace bulb, check operation of unit.

3.
Reinstall lens and retaining screws.

VIEW B

BACKING LAMPS

Fig.
18 - Rear Lighting (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-15

Fig.
21 - Qlal Quadrant Assembly ~ Camaro

SEAT SEPARATOR CONSOLE LAMPS

COMPARTMENT LAMP REPLACEMENT (Fig.
22)

1.
Remove (pry up) switch assembly from console open-

ing in.the instrument compartment.

2.
Remove bulb from the socket.

3.
Replace bulb and install switch assembly in console

opening.

COURTESY LAMP REPLACEMENT (Fig. 22)

1.
Remove two screws and lens at rear of console.

2.
Remove bulb from retainer.

3.
Replace the bulb, position the lens and install attach-

ing screws.

QUADRANT LAMP REPLACEMENT (Fig. 22)

1.
Remove Dial Quadrant Trim plate retaining screws

and lift trim plate assembly from console opening.

2.
Disconnect lamp socket from the retainer and re-

move bulb from the socket.

3.
To install, insert bulb into the socket and snap the

socket assembly into the retainer.

Position the trim plate assembly into the console

opening and install the retaining screws.
4.

LIGHTING SWITCH REPLACEMENT (Fig. 24)

1.
Disconnect battery ground cable.

2.
Pull control knob out of headlamp ON position.

3.
Reach under instrument panel and depress the switch

shaft retainer (Fig. 25) and remove knob and shaft

assembly.

4.
Remove ferrule nut using Tool J-21932 and remove

switch assembly from instrument panel.

NOTE:
Some Chevelle models require use of

ToolJ-4880.

5. Disconnect the multi-plug connector from the lighting

switch. A screw driver may be inserted in the side
of the switch to pry the connector from the switch.

6. Connect the multi-plug connector to the replacement

switch (Fig. 23). Connect battery cable to battery

terminal and check operation of the light switch'in all

positions.

NOTE:
Ground switch- to check dome lamp

operation.

7. Position switch and bezel to panel mounting hole and

install ferrule jmt.

8. Insert switch control knob and shaft assembly into

switch until retainer engages shaft.

WIPER SWITCH REPLACEMENT (Fig. 26)

1.
Disconnect battery ground cable.

2.
Remove the connectors from the rear of the switch.

NOTE:
On Air Conditioned models it is nec-

essary to remove left A/C outlet duct for acces-

sibility to rear of switch.

3.
Loosen set screw and pull knob from switch shaft.

4.
Remove retaining nuts using special Tool J-21932

and withdraw wiper switch from behind console.

NOTE:
Some Chevelle models require special

ToolJ-4880.

5. To install, reverse removal procedure and check

operation of wipers.

STOPLIGHT SWITCH REPLACEMENT (Fig. 27)

1.
Disengage retaining fingers, disconnect wiring har-

ness connector from switch and unscrew switch from

mounting clip.

2.
Depress brake pedal and push new switch into clip

until shoulder bottoms out against clip.

3.
Check switch position for proper operation. Elec-

trical contact should be made when the brake pedal is

depressed 3/8" to 5/8" from fully released position.

DIMMER SWITCH REPLACEMENT (Fig. 28)

1.
Fold back upper left corner of front floor mat, disen-

gage connector lock fingers, and disconnect multi-

plug connector from dimmer switch.

2.
Remove two screws retaining dimmer switch to toe

pan.

3.
Connect multi-plug connector to new switch and

check operation. Install new switch to toe pan with

two screws. Replace floor mat.

BACKING LAMP SWITCH REPLACEMENT

Located on Mast Jacket (Fig. 29)

1.
Disconnect wiring connector at switch terminals.

2.
Remove switch attaching screws and switch from

mast jacket.

3.
Position new switch to mast jacket, install the re-

taining screws and connect wire connector to switch.

NOTE:
Position gear shift in neutral before

assembling switch to mast jacket.

4.
Check operation of switch.

Located on Transmission (Fig. 30)

1.
Raise and support vehicle.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-16

BACK-UP LAMP CONN.

CONSOLE CTSY

LAMP CONN

CLOCK CONN

NEUTRAL SAFETY SWITCH

Fig.
22 - AutoTrans — Seat- Separator Wiring — Chevelle

TAIL

PANEL Ll<

J
TAIL

LIGHTS ^^g

9

""TUtflll -^ ""

DOME
LIGHT

r

•I

m

/

LIGHTS
FUSE HEADLIGHTS

9R

jl PARKING LIGHTS

*^ R ATTPRY

Fig.
23 - Light Switch Terminal Connections
Fig.
24 - Light Switch and Cigarette

Lighter Installation

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-17

Fig.
25 - Shaft Retainer

2.
Disconnect switch wiring from harness wiring at

in-line connector.

3.
Remove bolt retaining wiring attaching clip to

transmission. *
• '
•

4.
Remove wire clip retaining reverse lever rod to

switch.

5. Remove screws retaining switch and shield assembly

to transmission, remove switch.

NOTE:
Do not remove transmission-to-bracket

retaining bolts.

6. To install, reverse removal procedure and check

switch for operation in transmission reverse range.
.38-.64"

VIEW A

Fig.-27 - Stoplight Switch Assembly

NEUTRAL SAFETY SWITCH REPLACEMENT

Column Shift (Fig. 31)

1.
Disconnect wiring harness connectors at switch ter-

minals..

2.
Remove switch retaining screws and switch from

mast jacket.

3.
To install, position shift lever in drive and locate

lever tang against transmission selector plate.

4.
Align slot in contact support with hole in switch and

insert pin (3/32" dia.) to hold support in place.

Switch is now in drive position.

5. Place contact support drive slot over shifter tube

drive tang and tighten screws. Remove clamp and

pin.

6. Connect wiring harness to switch terminals and

check operation of switch.

Floor Shift

Chevrolet, Chevelle, Chevy II and Camaro

(Fig.
31)

1.
Position shift lever in drive position. Remove ash

Fig.
26 - Windshield Wiper Switch

Fig.
28 - Dimmer Switch

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-19

VIEW A
•CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

PAWL
CONTACT POINT B

CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

FLOOR SHIFT

(EXCEPT CAMARO)
COLUMN SH

Fig.
31 - Neutral Safety Switches

PARKING BRAKE ALARM SWITCH REPLACEMENT

Corvette (Fig. 33)

1.
Remove seat belt retainer and parking brake cover

assembly from center console.

2.
Disconnect wire from brake alarm switch.

3.
Remove retaining screw and switch from

reinforcement.

4.
Position new switch to reinforcement and install re-

taining screw.

5. Connect switch wire and check operation of switch.

6. Install cover and seat belt retainer assembly.

Chevrolet, Chevelle, Chevy II and Camaro (Fig. 34)

1.
Disconnect wiring connector at switch terminal.

2.
Remove nut and lock washer or retaining bolt and

disengage switch from brace.

3.
To install, reverse removal procedure.

INSTRUMENT PANEL COMPARTMENT

LAMP/SWITCH REPLACEMENT

1.
Disconnect battery ground cable.

2.
Reach into glove box, depress bulb in end of switch
and turn counterclockwise to remove bulb.

3..
Remove switch from socket. Carefully detach wire

and terminal from switch.

NOTE:
On some model switches, the wire and

terminal cannot be detached from the switch

making it necessary to cut and splice the switch

wire.

4.
Insert wire and terminal into new switch.

5. Push switch into place and install bulb by setting it in

place, depressing and turning it clockwise.

CIGARETTE LIGHTER REPLACEMENT

Chevrolet, Chevy II, Camaro and Corvette (Fig. 23)

1.
Disconnect battery ground cable.

2.
Disconnect wire connector at rear of lighter unit

under dash.

3.
Remove retainer from rear of housing assembly and

disengage lighter unit from panel.

4.
To install, reverse removal procedure.

Chevelle (Fig. 35)

1.
Disconnect battery ground cable.

CHEVROLET CHASSIS SERVICE MANUAL