battery replacement CHEVROLET CAMARO 1967 1.G Chassis Service Manual

ELECTRICAL-BODY AND CHASSIS 12-43

23.
Install
MCtT
ring over steering shaft using snap ring

installer J-22659 (refer to Section 9).

NOTE: Be sure retaining ring is completely

seated into groove.

24.
Install dial pointer on Chevrolet and Chevelle models

equipped with automatic transmission (if applicable).

25.
Install dial indicator and lamp assembly on Camaro

and Chevy n models equipped with automatic

transmission.

26.
Install mast jacket lower trim covers (if applicable).

27.
Install hazard warning knob and turn signal lever.

28.
Install shift lever.

29.
Install steering wheel.

30.
Install multiple connector to switch wiring using old

harness for wire color guide and connect to body

harness connector.

31.
Connect battery ground cable and check operation of

assembly.

Tilt Steering Column (Fig. 57)

Chevrolet, Chevelle and Camaro

1.
Disconnect battery ground cable.

2.
Disconnect directional switch wiring harness from

body harness at multiple connector under instrument

panel.

3.
Remove steering wheel assembly (refer to Steering,

Section 9).

4.
Remove preload spring and cancelling cam from end

of shaft.

5.
Remove shift lever pin and lever from steering col-

umn (except floor shift).

6. Remove directional le*ver screw and lever.

7.
Push in hazard warning knob and unscrew knob.

8. On Camaro models equipped with automatic trans-

mission, remove quadrant dial and lamp assembly

from column.

9. Remove mast jacket trim cover
(s).

10.
On Chevrolet and Chevelle models with automatic

transmission, loosen set screw and remove quadrant

dial pointer.

11.
Assemble slide hammer Tool J-6585-1 to turn signal

cover remover Tool J-21486. Place cover remover

over turn signal cover, tighten clamp, and pull cover

from end of column with slide hammer (Refer to

Steering, Section 9).

12.
Remove three switch mounting screws, noting short

length of top screw.

13.
Cut multiple connector from switch wiring and slide

switch from end of column.

14.
To install new switch, feed wiring through the bear-

ing housing, around support, and through shift bowl

and shroud.

15.
Feed through wiring protector. If clearance is not

sufficient loosen mast jacket bracket retaining bolts.

16.
Insert switch wiring terminals in multiple connector.

Use old connector
and
wiring for color guide.
17.
Position switch and install three mounting screws

with short screw in top position.

18.
Be sure hazard warning switch is pushed in, then

install turn signal cover using special Tool J-21853.

On automatic columns align key in cover with keyway

in bearing housing.

19.
Install turn signal lever, hazard warning knob and

tilt lever.

20.
Install shift lever and roll pin (where applicable).

21.
Install dial pointer on Chevrolet and Chevelle. On

Camaro install dial indicator and lamp assembly.

22.
Install trim covers and retaining screws.

23.
Install cancelling cam and preload spring.

24.
Install steering wheel (Refer to Section 9).

25.
Connect switch wiring to body harness under instru-

ment panel.

26.
Connect battery ground cable and check operation of

unit.

Standard and Telescoping Steering Column

Corvette (Fig. 58)

1.
Disconnect battery ground cable.

2.
Disconnect signal switch harness wiring from chas-

sis wiring harness at multiple connector under in-

strument panel.

3.
Remove steering wheel assembly as outlined in

Steering, Section 9.

4.
Remove preload spring and cancelling cam.

5.
Remove directional signal lever screw and lever.

6. Push in hazard warning knob, unscrew and remove

knob.

7.
Remove lower trim cover retaining screws and

cover.

8. Remove retaining ring, thrust and wave washers

from upper end of shaft.

9. Cut wiring above connector.

10.
Remove three switch mounting screws, slide switch,

cover and upper bearing housing from column, pull-

ing wire through protector and escutcheon.

11.
To install replacement switch, assemble upper bear-

ing housing and turn signal switch into switch cover,

then feed wiring through escutcheon and protector

until switch can be positioned on mast jacket.

12.
With switch positioned on mast jacket, install three

switch mounting screws.

13.
Install thrust and wave washers and snap lock ring

in place.

14.
Install turn signal lever and hazard warning knob.

15.
Install cancelling cam and upper bearing preload

spring on steering shaft.

16.
Install steering wheel assembly.

NOTE:
Be sure directional signal switch is in

neutral position before installing wheel.

17.
Install connector on directional signal wiring har-

ness and connect to body harness connector.

CHEVROLET CHASSIS SERVICE