stop start Citroen BERLINGO 2017 2.G User Guide

55
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
The Stop & Start system
requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type of battery must be done only
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For more information on the 12 V
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If the temperature is high
enough, the warning lamp
comes on for less than
one second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp to go off then operate the starter
(Starting position) until the engine
starts. Door or bonnet open
warning lamp
If this comes on, a door or the bonnet
is
  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (Diesel engine) to
return
  to   idle.
Do not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related to an automatic change to
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it is strongly recommended that you
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For more advice on driving, particularly
on
 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
READY TO GO
3
Stop & Start

57
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Starting and switching off
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
DRIVING RECOMMENDATIONS
Observe the driving regulations and
remain  vigilant   whatever   the   traffic  
conditions.
Pay

  close   attention   to   the   traffic   and  
keep

  your   hands   on   the   wheel   so   that  
you are ready to react at any time to
any

  eventuality.
As a safety precaution, the driver
must only carry out actions requiring
sustained attention when the vehicle is
stationary.
On
  a   long   journey,   a   break   every  
two hours

  is   strongly   recommended.
In
  difficult   weather,   drive   smoothly,  
anticipate

  the   need   to   brake   and  
increase the distance from other
vehicles.
Driving on flooded roads
We strongly advise against driving
on  flooded   roads,   as   this   could   cause  
serious damage to the engine or
gearbox, as well as to the electrical
systems

  of   your   vehicle. If you are obliged to drive through
water:
-
 
check
  that   the   depth   of   water   does  
not

  exceed   15   cm,   taking   account  
of waves that might be generated
by other users,
-

deactivate the Stop & Start system,
-

drive as slowly as possible without
stallin

g.   In   all   cases,   do   not   exceed  6
  mph   (10   km/h),
- do not stop and do not switch of f
the
  engine.
On
  leaving   the   flooded   road,   as   soon  
as

  circumstances   allow,   make   several  
light

  brake   applications   to   dry   the   brake  
discs

  and   pads.
If in doubt on the state of your vehicle,
contact a CITROËN dealer or a
qualified
  workshop.Never
  drive   with   the   parking   brake  
applied

  -   Risk   of   overheating   and  
damage

  to   the   braking   system!
Risk   of   fire!
As the exhaust system of your vehicle
is very hot, even several minutes
after switching off the engine, do not
park   or   leave   the   engine   running   over  
areas

  where   inflammable   substances  
and

  materials   are   present:   grass,  
leaves, etc.
Never leave a vehicle
unsupervised with the engine
running.
  If   you   have   to   leave  your vehicle with the engine running,
apply
  the   parking   brake   and   put   the  
gearbox into neutral or position

N or P,
depending
  on   the   type   of   gearbox.
Important!
READY TO GO
3

59
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
LED DAYTIME RUNNING LAMPS
Rear foglamps (amber,
2nd rotation of the ring
forwards).
Front foglamps (green,
1st
rotation of the ring
forwards). Rotate this ring forwards
to switch on and
rearwards   to   switch   off.
Their   state   is   confirmed   by  
the warning lamps in the
instrument

  panel. Do not forget to switch them off
when   they   are   no   longer   needed.
Operation of the automatic illumination
of headlamps switches off the rear
foglamps, but the front foglamps
remain   on.
To switch off the front and
rear foglamps, turn the
ring rearwards twice in
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the sunshine sensor may detect
sufficient   light.
As a consequence, the lighting
will
  not   come   on   automatically.   If  
necessary

, you must switch on
the dipped
  beam   headlamps   manually.
Do not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination of headlamps and for the
automatic
  rain   sensitive   wipers.
Activation The sidelamps
and dipped beam
headlamps switch
on automatically if
the light is poor, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light becomes bright enough or the
windscreen

  wipers   stop.
On starting the vehicle, in daylight the
LED daytime running lamps come on
automatically.
If the sidelamps and headlamps are
switched on manually or automatically,
the
 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day is not a legal requirement, you can
activate or deactivate the function via
the   configuration   menu.
If the user does not operate any
equipment for 30 minutes, the
Economy mode engages to avoid
discharging
 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp operation is not affected by
Economy
 
mode.
In clear weather or in rain, both day
and night, rear foglamps dazzle and
their  use   is   prohibited.
Refer to chapter 8, "Battery
section".
Front and rear foglamps
They operate with the sidelamps and
dipped
 
beam
 
headlamps.
Turn the ring to the AUTO  position.  The activation of this function is
accompanied by a message in the
screen.
Deactivation
T
urn   the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied by a message in the
screen. This function is not compatible with
daytime
  running   lamps.
Steering mounted controls
EASE OF USE and COMFORT
4

158
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When the engine is warm, the
temperature of the coolant is controlled
by
  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and because the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has dropped, remove the cap and top
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this indicates a fault which must be
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes as soon as possible, when
traffic
  conditions   permit   (until   the  
message disappears and the service
warning

  lamp   goes   off).
During regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating may be heard under the
dashboard.
If the message is still displayed and
if the service warning lamp remains
on, contact a CITROËN dealer or a
qualified

  workshop.
Topping up
The level must be between the MIN
and
 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For optimum cleaning and to avoid
freezing,
  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This additive must be topped up by
a  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
Avoid prolonged contact of used oil
with  the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITROËN dealer (France) or
an

  authorised   waste   disposal   site.
The minimum level of this additive
is indicated by lighting of the service
warning lamp, accompanied by an
audible signal and a message in the
screen.
When this occurs with the engine
running it is due to the start of
saturation
 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

163
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
DIESEL PRIMING
PUMP
If you run out of fuel, it is necessary to
prime
  the   fuel   circuit.
Other HDi engines
- Fill  the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-

Squeeze and release the manual
priming pump, under the bonnet,
under

  the   protective   cover.
-

Operate the starter until the engine
starts.
BlueHDi engine
- Fill   the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-

Switch on the ignition (without
starting

  the   engine).
-

W
ait around 6 seconds and switch
off
  the   ignition.
-
 
Repeat
  the   operation   10   times.
-

Operate the starter to run the
engine.
FUEL CUT- OFF
In a serious collision, a mechanism
automatically prevents fuel from
reaching
  the   engine.
The
  flashing   of   this   warning  
lamp is accompanied by a
message

  in   the   screen.
Check
  that   there   is   no   odour   or  
leakage

  of   fuel   outside   the   vehicle   and  
re-establish

  the   fuel   supply:
-

switch of
f the ignition
(STOP


position),
-
 
remove
  the   key,
-
 
put
  the   key   back   in   the   ignition,
-
 
switch
  on   the   ignition   and   start.
CHECKS
7
AdBlue®

166
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Range indicators
Rules on the display of alertsFor more information on the
displays and warning lamps, refer
to chapter 3, "Instruments and
controls"
  section. Range greater than 1 500 miles
(2 400 km)
No
  information   displayed.
Once   the   1   500   miles   (2   400   km)  
threshold is reached, the UREA


warning lamp comes on temporarily
and the remaining range message is
displayed.
The alert is repeated every 200 miles
(300
  km)   until   the   next   threshold   is  
reached.
Every time the ignition is switched
on, the alert is given, together with an
audible

  signal.
Remaining range less than
1
500 miles (2 400 km) and greater
than 350 miles (600 km)
Driving range
With
  the   touch   screen   tablet:
If the range is greater than 3 100 miles
(5
  000   km),   a   range   value   is   not   given.
Press this button to display
the
  information.
-

select the "Driving
assistance" menu,
-


select "Diagnostic",
-

 
select
  CHECK.
Different levels of alert are triggered
according to the remaining driving
range threshold
You will be informed as each mileage
threshold is reached and the alerts will
change
  from   temporary   to   permanent.
-

The 1st is triggered at a remaining
driving range of 1 500 miles
(2
 
400
  km).
-

The 2nd is triggered at a remaining
driving range of 350 miles
(600
 
km).
-

Up to 0 miles, at which point it will
be impossible to restart the engine
after

 
a
 
stop.
AdBlue®

170
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
BATTERY
Before disconnecting the battery, you
must wait for 2 minutes after switching
off  the   ignition.
Never disconnect a terminal when the
engine
  is   running.
Never
  charge   a   battery   without   first  
disconnecting

  the   terminals.
After every reconnection of the battery,
switch on the ignition and wait 1 minute
before starting to allow the electronic
systems
  to   be   initialised.   If   problems  
remain after doing this, please contact
a

  CITROËN   dealer   or   a   qualified  
workshop.
After changing bulbs, wait
approximately 3 minutes before
reconnecting

  the   battery.
It is advisable to disconnect the
battery if the vehicle is not to be
used for a period of more than
one month.
To charge the battery using a
battery charger
- Disconnect  the   battery.
-
Follow the instructions for use
given by the battery charger
manufacturer

.
-

Reconnect starting with the
negative

  (-)   terminal.
-
 
Check
  that   the   terminals   and  
connectors

  are   clean.   If   they   are  
covered with sulphate (white or
greenish deposit), disconnect them
and

  clean   them.
To start the vehicle from
another battery
- Connect the red cable to the
positive (+) terminals of the
two batteries.
-

Connect one end of the green
or

  black   cable   to   the   negative   (-)  
terminal

  of   the   slave   battery.
-

Connect the other end of the green
or

  black   cable   to   an   earth   point   on  
the

  broken   down   vehicle   as   far   as  
possible

  from   the   battery.
-
 Operate

  the   starter,   let   the   engine   run.
-

W
ait for the engine to return to idle,
then
  disconnect   the   cables.
The presence of this label
indicates the use of a 12 V
lead-acid battery with special
technology
 
and
 
specification,
 
for
 
which
 
the involvement of a CITROËN dealer
or

 
qualified
 
workshop
 
is
 
required
 
when
 
replacing

 
or
 
disconnecting
 
the
 
battery.
Failure to observe this recommendation
may cause premature wear of the
battery.
After
 
refitting
 
the
 
battery,
 
the
 
Stop &
 
Start system will only be active after
several hours depending on the
climatic conditions and the state of
charge of the battery (up to about
8 hours).
The Stop & Start battery does not have
to

 
be
 
disconnected
 
for
 
charging.
Battery

171
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
ECONOMY MODE
After the engine has stopped, with
the
  key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows, courtesy lamps, audio
equipment,
  etc.)   can   only   be   used   for   a  
cumulative duration of thirty minutes, to
prevent

  discharging   of   the   battery.
Once the thirty minutes have elapsed,
the active functions are put on standby
and
  the   battery   warning   lamp   flashes  
accompanied by a message in the
screen.
T

o resume the use of these functions
immediately, start the engine and let it
run
  for   a   few   minutes.
The time available will then be double
the time for which the engine was left
running.
  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery
QUICK HELP
8

199
Berlingo2VP_en_Chap09_Caract-technique_ed02-2016Berlingo2VP_en_Chap09_Caract-technique_ed02-2016
Diesel Engines / Weights
5-seatEngine Gearbox Engine oil
capacity with filter
replacement (litres) Unbraked trailer (kg)
Recommended nose
weight (kg)
1.6 HDi 75 hp 5-speed manual -600 70
1.6 HDi 75 hp FAP 5-speed manual -715 70
BlueHDi 75 hp Euro
65-speed manual
-720 70
1.6 HDi 90 hp 5-speed manual 3.75735 70
1.6 HDi 92 hp FAP 5-speed manual 3.75715 70
1.6 e-HDi 92 hp FAP 5-speed manual 3.75690 70
1.6 BlueHDi 100 hp Euro 6 5-speed manual
3.75600 70
1.6 BlueHDi 100 hp S&S 5-speed manual
3.75600
70
6-speed electronic 60070
1.6 HDi 115 hp FAP 5-speed manual 3.75735 70
1.6 BlueHDi 120 hp Euro 6 6-speed manual
3.75600 70
FA P :
 

particle   filter.
e-HDi :
  model   equipped   with   Stop   &   Start.
TECHNICAL DATA
9
Weights

200
Berlingo2VP_en_Chap09_Caract-technique_ed02-2016Berlingo2VP_en_Chap09_Caract-technique_ed02-2016
7-seatEngine Gearbox Engine oil
capacity with filter
replacement (litres) Unbraked trailer (kg)
Recommended nose
weight (kg)
1.6 HDi 92 hp FAP 5-speed manual 3.75750 70
1.6 BlueHDi 100 hp Euro 6 5-speed manual
3.75600 70
1.6 BlueHDi 100 hp Euro 6 S&S 5-speed manual
3.75600 70
1.6 HDi 115 hp FAP 5-speed manual 3.75750 70
1.6 BlueHDi 120 hp Euro 6 6-speed manual
3.75600 70
FA P :
 

particle   filter.
e-HDi :
  model   equipped   with   Stop   &   Start.
Weights