Citroen BERLINGO MULTISPACE RHD 2015 2.G Owner's Manual

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
169
3. d irection indicators
type B

,   PY21W   -   21W   (amber)
-
 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-
 
T
urn   the   bulb   holder   a   quarter  
turn

  anticlockwise.
-
 
Remove
  the   bulb   by   pressing  
it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure
correct

  sealing.
2.
Sidelamps


type A

, W5W - 5W
-
 
Remove

 
the
 
cover
 
by
 
pulling
 
the
 
flexible

 
rubber
 
tab.
-
 
Remove

 
the
 
bulb
 
holder
 
fitted
 
by
 
pressure

 
by

 
pullin

g
 
the

 
connector

.
-
 
Change

 
the
 
bulb.
-
 
Ensure

 
that
 
the
 
cover
 
is
 
refitted
 
correctly all round to assure
correct

 
sealing.
FrOnt LAMPS
1. d ipped / Main beam headlamps
type

c , H4 - 55W
-
 
Remove
  the   centre   cover   by  
pullin

g   the   flexible   rubber   tab.
-
d isconnect the electrical
connector.
-
 
Release
  the   retaining   tab.
-
 
Change
  the   bulb   taking   care  
to

  align   the   metal   part   with   the  
grooves

  on   the   lamp.
-
 
Reposition
  the   retaining   tab.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure
correct

  sealing.
Changing a bulb
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
170
4. Foglamps type
c , H1 - 55W
-
 
Remove
  the   three   clips   and   the  
screw securing the wheelarch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheelarch   liner   upwards.
-
 
Remove
  the   foglamp   by   removing  
the screw

, which can be accessed
via the hole provided for this
purpose
  in   the   bumper,   using   a  
T

orx
© 30 screwdriver.
-
 Unclip   the   foglamp   by   squeezing  
the

 
clip   to   release   it.
-

Remove the foglamp from the outside.- Turn the yellow cover a 1/4 turn to open.- Separate the clips which secure
the base of bulb on each side to
release   the   bulb.
-
 
Remove
  the   bulb   by   pulling,  
keeping

  it   straight.
-

Insert the new bulb, reposition the
clips around the base of the bulb
and carry out the operations in
reverse

  order   to   put   the   lamp   unit  
and

  the   bumper   back   in   position.
SIdE rEPEAtE r
type A,   WY5W   -   5W   (amber)
-
Push the repeater towards the rear
and disengage it by pullin

g the
front.
-

Contact a CITR
o Ë n dealer to
obtain a new repeater which is a
sealed
  component.
-
 
T
o   refit,   engage   the   repeater  
towards the rear and bring it
towards

  the   front.
cOurtESY LAMPS
type A, 12V5W - 5W
-
Unclip the lens by sliding a
screwdriver in the slots on each
side

  of   the   courtesy   lamp.
-
 
Pull
  the   bulb   out   and   change   it.
-

Clip the lens in its housing and
ensure

  that   it   is   secured   correctly.
Front /
r ear
Changing a bulb

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
171
rEAr LAMPS
This procedure requires the use of the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the supply
wire correctly to avoid trapping


the
  wire.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time  
is
  above   2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
concerning
 
the
 bulbs,
 
refer
 
to
 
the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


type B

,
 
P21/5W
 
-
 
21/5W
2.
d
irection indicators
type B

,
 
PY21W
 
-
 
21W
 
(amber)
3.
r
eversing lamps
type B

, P21W - 21W
4.

Foglamps


type B

, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the faulty bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
Changing a bulb
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
172
nuMBEr PLAtE LAMPS
- Unscrew  the   two   nuts.
-  
Push
  the   pins.
-

If necessary
, disconnect the
connector
  to   remove   the   lamp.
-
 
Change
  the   bulb.
With tailgate
-
d
isengage the plastic lens using a
screwdriver.
-
 
Change

 
the
 
bulb.
-

Replace the plastic lens and press
on

 
it.
tHIrd BrAKE LAMP
type A ,   W16W   -   16W
With hinged doors
-
 
Unclip

 
the
 
interior
 
trim.
-
d
isconnect the connector by
moving
 
aside
 
its
 
tab.
-
 
T

urn
 
the
 
bulb
 
holder
 
a
 
quarter
 
turn
 
anticlockwise.
-

 
Change

 
the
 
bulb.
-
 
Put

 
the
 
bulb
 
holder
 
back
 
in
 
place
 
and

 
reconnect
 
the
 
connector.
-
 
Put

 
the
 
trim
 
back
 
in
 
place.type A
, W5W - 5W
Changing a bulb

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
173
cHAnGInG A FuSE
The fuseboxes are located:
-
in the lower dashboard on the left-
hand side (behind the cover),
-

 
under
  the   bonnet   (near   the   battery).
The
  information   given   concerns   only  
those fuses which can be changed by
the user using the tweezer

, located
behind the dashboard storage
compartment
  on   the   right-hand   side.  
For

  any   other   work,   visit   a   CITROËN  
dealer

  or   a   qualified   workshop.
removing and fitting a fuse
Always replace a failed fuse with
a fuse of the same rating.
Motor
 
trade
 
technicians:
 
for
 
complete

 
information
 
on
 
the
 
fuses
 
and relays, refer to the "Repair
Manual"

 
diagrams
 
via
 
the
 
dealer
 network.
CITR
o
Ë
n
will not accept responsibility
for the cost incurred in repairing
your vehicle or for rectifying the
malfunctions
 
resulting
 
from
 
the
 
installation of accessories not
supplied

 
and
 
not
 
recommended
 
by
 
the
 
CITROËN

 
network
 
and
 
not
 
installed
 
in accordance with its instructions,
in

 
particular
 
when
 
the
 
combined
 
consumption

 
of
 
all
 
of
 
the
 
additional
 
equipment

 
connected
 
exceeds
 
10 millia

mperes. Before replacing a fuse, the cause of
the
 
incident
 
must
 
be
 
identified
 
and
 
rectified.
●

 
Use

 
the
 
tweezer.
Changing a fuse
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
174
dASHBOArd FuSES
Tilt the cover to gain access to the
fuses.Fuses
F Amperes  Aa
llocation
1 15 Rear wiper
2 - Spare
3 5
a

irbag
4 10 Air
  conditioning,   diagnostic   socket,   mirror   control,  
headlamp

  beam
5 30 Electric windows
6 30Locks
7 5Rear
  courtesy   lamp,   front   map   reading   lamp,   roof  
console
8 20 Audio

  equipment,   screen,   tyre   under-inflation  
detection,

  alarm   and   siren
9 30Front
  and   rear   12V   socket
10 15 Central
  column
11 15 Low current ignition switch
12 15 Rain and sunshine sensor, airbag
13 5 Instrument
  panel
14 15 Parking
  sensors,   digital   air   conditioning   controls,  
hands-free

  phone   kit
15 30 Locks
16 - Spare
17 40Rear
  screen/mirrors   demist/defrost
Changing a fuse

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
175
PASSEnGEr cOMPArtMEnt FuSES
Fuses F Amperes
 
Aa
llocation
1 - Spare
2 20 Heated seats
3 - Spare
4 15 Folding
  mirrors   relay
5 15 Refrigeration
  equipment   socket   relay
Changing a fuse
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
176
FuSES undEr tHE BOnnEt
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
  the   fuses. Fuses
F Amperes  Aa
llocation
1 20 Engine
  management
2 15 Horn
3 10 Front
  and   rear   wash-wipe   pump
4 20 Headlamp
  wash   pump
5 15 Engine
  components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
  switch,   clutch   switch
8 25 Starter
9 10Headlamp
  beam   motor,   parc   management   unit
10 30 Engine
  components
11 40 Spare
12 30 Wipers
13 40 Built-in
  systems   interface
14 30 Pump
15 10 Right-hand
  main   beam   headlamp
16 10Left-hand
  main   beam   headlamp
17 15Right-hand
  dipped   beam   headlamp
18 15 Left-hand
  dipped   beam   headlamp
Changing a fuse

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
177
Placing the windscreen wiper
blades in the special position
- Less  than   a   minute   after   switching  of
f  the  ignition,  press  the  wiper  stalk  
downwards to position the wiper
blades along the windscreen pilla

rs
(special
  position).
c
hanging a front wiper blade
-  
Lift
  the   wiper   arm.
-  Unclip   the   blade   and   remove   it.
-  Fit   the   new   blade.
-
 
Push
  back   the   wiper   arm.
To return the windscreen wipers to
their
  normal   position,   switch   on   the  
ignition

  and   operate   the   wiper   stalk.
c
hanging the rear wiper blade
-  
Lift
  the   wiper   arm,   then   unclip   the  blade
  and   remove   it.
-  Fit   the   new   blade   and   push   back  
the

  wiper   arm.
cHAnGInG A WIPEr BLAdE
Changing a wiper blade
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
178
Without lifting (4 wheels on the
road)
You should always use a towing bar.
BEInG tOWEd
Ths procedure involves the use of the
towing eye supplied with the tools for
changing
  a   wheel.
From the front
- Unclip the cover by pressing the
bottom  part.
-
 
Fully
  screw   in   the   removable   towing  
eye.
From the rear
- Unclip the cover using a coin or the
flat  part   of   the   towing   eye.
-
 
Fully
  screw   in   the   removable   towing  
eye. When towing with the engine
switched

  off,   there   is   no   braking   or  
steering

  assistance.
Lifting (only 2 wheels on the
road)
It is preferable to raise the vehicle
using
  professional   lifting   equipment.
Vehicles fitted with a manual
gearbox (d iesel version)
In the case of vehicles fitted with a  manual   gearbox,   the   gear   lever  
must

  be   in   neutral,   failure   to   observe  
this

  special   condition   may   result   in  
damage

  to   transmission   and   braking  
components

  and   the   absence   of  
braking

  assistance   when   the   engine   is  
started

  again.
Chapter
 
9,
 
"Changing
 
a
 
wheel"
 
section.
Having your vehicle towed