battery CITROEN C-ELYSÉE 2016 User Guide

80
C-elysee_en_Chap05_conduite_ed01-2016
There is a risk of damage to the gearbox:
-
 
i
f   you   press   the   accelerator   and  
b

rake   pedals   at   the   same   time,
-
 
i
f   you   force   the   movement   of   the  
s

elector   from   the   P position to
another position when the battery is
discharged.
If the selector is not in position P
,
when
 
the
 
driver's
 
door
 
is
 
opened
 
or
 
a

pproximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F

R

eturn the selector to position P ;
 
t

he
 
message
 
disappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace. To
  reduce   fuel   consumption   when   at  
a

  prolonged   standstill   with   the   engine  
r

unning   (traffic   jam...),   put   the   selector  
i

n the N   position   and   apply   the   parking  
b

rake.
Manual operation
Invalid value during manual
operation
Stopping the vehicle
Before switching off the engine, you can e ngage   position   P or N   to   place   the   gearbox   in  
neu

tral.
In
  both   cases,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle.
Operating fault
F Select position M for sequential c hanging o
f   the   six   gears.
F
 
M
ove   the   selector   towards   the   +   sign   to  
c

hange   up   a   gear.
F
 
M
ove   the   selector   towards   the   -   sign   to  
c

hange   down   a   gear.
It
  is   only   possible   to   change   from   one   gear   to  
a

nother   if   the   vehicle   speed   and   engine   speed  
p

ermit;   other wise,   the   gearbox   will   operate  
t

emporarily   in   automatic   mode.
D
  disappears   and   the   gears  
e

ngaged   appear   in   succession   in   the  
in

strument
 pan
el.
If
  the   engine   speed   is   too   low   or   too   high,   the  
g

ear   selected   flashes   for   a   few   seconds,   then  
t

he   actual   gear   engaged   is   displayed.
It
  is   possible   to   change   from   position   D
(automatic)
  to   position   M   (manual)   at   any   time.
When
  the   vehicle   is   stationary   or   moving  
v

ery   slowly,   the   gearbox   engages   first   gear  
au

tomatically. With
 t he  i gnition  o n,  i llumination  o f  
t

his   warning   lamp,   accompanied  
b

y   an   audible   signal   and   a   message   in   the  
m

ultifunction   screen,   indicates   a   gearbox   fault.
In
  this   case,   the   gearbox   switches   to   back-up  
m

ode   and   is   locked   in   3rd   gear.   You   may   feel  
a

  substantial   knock   when   changing   from   P
to R
  and   from   N to R.
  This   will   not   cause   any  
d

amage   to   the   gearbox.
Do
  not   exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact
  a   CITROËN   dealer   or   a   qualified  
w

orkshop   as   soon   as   possible.
This
  symbol   is   displayed   if   a   gear  
i

s   not   engaged   correctly   (selector  
b

etween   two   positions).
The
  sport   and   snow   programmes   are  
n

ot   available   when   operating   manually.
Driving

83
C-elysee_en_Chap05_conduite_ed01-2016
Going into engine START mode Special cases: START invoked automatically
The "ECO" warning   lamp   goes  o
ff   and   the   engine   starts   with   an  
e

lectronic gearbox :
-
 
g

ear
 
selector   in   position   A or M, when you
release
  the   brake   pedal,
-
 
o

r
 
gear   selector   in   position   N   and   the   brake  
p

edal
  released,   when   you   move   the   gear  
s

elector to position A or M ,
-
 
o

r
 
when   you   engage   reverse   gear.For
  reasons   of   safety   and   for   your   comfort,  S
TART   mode   is   invoked   automatically   when:
-
 
y
ou   open   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   2   mph  
(

3 km/h)   with   an   electronic   gearbox,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   for   control   of   a   system.
The "ECO"
 

warning   lamp   flashes   for  
a

  few   seconds,   then   goes   off.
This operation is per fectly normal.
Special cases: STOP mode not
available
STOP mode is not invoked when:
-  t he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
The "ECO"
 

warning   lamp   flashes   for  
a

  few   seconds   then   goes   off.
This operation is per fectly normal.
5
Driving

84
C-elysee_en_Chap05_conduite_ed01-2016
In the event of a fault with the system, the indicator   lamp   in   the   "ECO OFF" button
flashes
  for   a   few   moments,   then   comes   on  
c

ontinuously.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
In
  the   event   of   a   fault   in   STOP   mode,   the  
v

ehicle   may   stall.   All   of   the   warning   lamps  
i

n   the   instrument   panel   come   on.   It   is   then  
n

ecessary   to   switch   off   the   ignition   and   start  
t

he   engine   again   using   the   key.
Operating fault
The Stop & Start system requires 
a   12   V   battery   with   a   special  
s

pecification
 a
nd
 t
echnology.
All
  work   on   this   type   of   battery   must   be  
c

arried   out   only   by   a   CITROËN   dealer  
o

r   a   qualified   workshop.
For
  more   information   on   the   12   V  
b

attery,   refer   to   the   corresponding  
s

ection.
Press
 
this
 
button
 
to
 
deactivate
 
the
 
system.
Deactivation
 
is
 
confirmed
 
by
 
illumination
 
of
 
the
 i
ndicator
 
lamp
 
in
 
the
 
button
 
and
 
the
 
display
 
of
 
a

 
message.
Pressing
 
this
 
button
 
again
 
reactivates
 
the
 
s

ystem.
The
 
indicator
 
lamp
 
in
 
the
 
button
 
goes
 
off,
 
a

ccompanied
 
by
 
the
 
display
 
of
 
a
 
message.
Deactivation / Manual
reactivation
In certain cases, such as the need to maintain a   comfortable   temperature   in   the   passenger  
c

ompartment,   it   may   be   useful   to   deactivate   the  
S

top   &   Start   system.
The
  system   can   be   deactivated   at   any   time,  
o

nce   the   ignition   is   on.
If
  the   engine   is   in   STOP   mode,   it   then   restarts.
The
  Stop   &   Start   system   is   reactivated  
a

utomatically   every   time   the   ignition   is  
switched
  on.
Opening the bonnet
Before
  doing   anything   under   the  
b

onnet,   deactivate   the   Stop   &   Start  
s

ystem   to   avoid   the   risk   of   injury  
r

elated   to   an   automatic   change   to  
S

TART mode.
Driving on flooded roads
Before
  driving   through   a   flooded   road,  
i

t   is   strongly   recommended   that   you  
d

eactivate   the   Stop   &   Start   system.
For
  more   advice   on   driving,   particularly  
o

n   flooded   roads,   refer   to   the  
c

orresponding
 s
ection.
Driving

94
C-elysee_en_Chap06_visibilite_ed01-2016
In good or rainy weather, both day and   night,   the   front   foglamps   and   the  
r

ear   foglamp   are   prohibited.   In   these  
s

ituations,   the   power   of   their   beams  
m

ay   dazzle   other   drivers.   They   should  
o

nly   be   used   in   fog   or   snow.
In
  these   weather   conditions,   it   is   your  
r

esponsibility   to   switch   on   the   foglamps  
a

nd   dipped   beam   headlamps   manually  
a

s   the   sunshine   sensor   may   detect  
s

ufficient   light.
Do
  not   forget   to   switch   off   the   front  
f

oglamps   and   the   rear   foglamp   when  
t

hey   are   no   longer   necessary.Switching on the lamps
after the ignition is
switched off
To reactivate the lighting control, rotate the   ring   to   the   "0"  position   -   lamps   off,  
t

hen   to   the   desired   position.
On
  opening   the   driver's   door   a  
t

emporary   audible   signal   warns   the  
d

river   that   the   lighting   is   on.
The
  lamps,   with   the   exception   of   the  
s

idelamps,   switch   off   automatically   after  
a

  maximum   duration   of   thirty   minutes   to  
p

revent   discharging   of   the   battery.
Switching off the lamps
when the ignition is
switched off
On switching off the ignition, all of the lamps   turn   off   immediately,   except   for  
d

ipped   beam   if   guide-me-home   lighting  
i

s   activated.
Visibility

163
C-elysee_en_Chap09_info-pratiques_ed01-2016
Fuse N°Rating Functions
F14 15 AHeated
  lower   windscreen.
F15 5 AAir
  conditioning   compressor.
F16 15 AFront
 fo

glamps.
F18 10 ARight
  hand   main   beam   headlamp.
F19 10 ALeft
  hand   main   beam   headlamp.
F29 40 AFront
  wiper   motor.
F30 80 APre-heater
 p

lugs
 (
Diesel).
Access to the fuses
F Unclip  the   cover.
F  C hange   the   fuse   (see   corresponding  
par

agraph).
F
 
W
hen   you   have   finished,   close   the   cover  
c

arefully   to   ensure   correct   sealing   of   the  
f

usebox.
Fuse tableEngine compartment
fuses
The fusebox is placed in the engine c
ompartment   near   the   battery   (left-hand   side).
9
Practical information

164
C-elysee_en_Chap09_info-pratiques_ed01-2016
12 V battery
Procedure for starting the engine using another battery or charging a discharged battery.T he   battery   is   located   under   the   bonnet.
To
  gain   access   to   it:
F
 
o
pen   the   bonnet   using   the   interior   release  
l

ever,   then   the   exterior   safety   catch,
F

s
ecure the bonnet stay,
F
 
r
emove   the   plastic   cover   on   the   (+)   terminal.
Access to the battery
General points
Lead-acid starter batteries
Protect your eyes and face before h
andling   the   battery.
All
  operations   on   the   battery   must   be  
c

arried   out   in   a   well   ventilated   area   and  
a

way   from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   or   fire.
Wash
  your   hands   after wards.
Batteries
 
contain
 
harmful
 
substances
 
s

uch
 
as
 
sulphuric
 
acid
 
and
 
lead.
They
 
must
 
be
 
disposed
 
of
 
in
 
a

ccordance
 
with
 
regulations
 
and
 
must
 
n

ot,
 
in
 
any
 
circumstances,
 
be
 
discarded
 
w

ith
 
household
 
waste.
Take
 
used
 
remote
 
control
 
batteries
 
and
 
v

ehicle batteries to a special collection
point.
Versions
 
equipped
 
with
 
Stop
 
&
 
Start
 
are
 
f

itted
 
with
 
a
 
12
 
V
 
lead-acid
 
battery
 
of
 
s

pecific
 t

echnology
 a

nd
 s

pecification.
Its
 
replacement
 
should
 
be
 
carried
 
out
 
o

nly
 

by
 

a
 

CITROËN
 

dealer
 

or
 

a
 

qualified
 w

orkshop. If
  you   have   an   electronic   or   automatic  
g

earbox,   never   try   to   start   the   engine   by  
p

ushing   the   vehicle. The
  (-)   terminal   of   the   battery   is   not   accessible.  
A

  remote   earth   point   is   located   on   the   engine.
Practical information

165
C-elysee_en_Chap09_info-pratiques_ed01-2016
Starting using another
battery
F Start  the   engine   of   the   vehicle   with   the  g
ood   battery   and   leave   it   running   for   a  
f

ew minutes.
F
 
O
perate   the   starter   on   the   broken   down  
v

ehicle   and   let   the   engine   run.
 I

f   the   engine   does   not   start   straight   away,  
s

witch   off   the   ignition   and   wait   a   few  
m

oments   before   trying   again.
Never
 
try
 
to
 
start
 
the
 
engine
 
by
 
c

onnecting
 
a
 
battery
 
charger.
Never
 
use
 
a
 
24
 
V
 
or
 
higher
 
battery
 
b

o o s t e r.
First
 
check
 
that
 
the
 
slave
 
battery
 
has
 
a
 
n

ominal
 
voltage
 
of
 
12
 
V
 
and
 
a
 
capacity
 
a

t
 
least
 
equal
 
to
 
that
 
of
 
the
 
discharged
 
b

attery.
The
 
two
 
vehicles
 
must
 
not
 
be
 
in
 
contact
 
w

ith
 
each
 
other.
Switch
 
off
 
the
 
electrical
 
consumers
 
on
 
b

oth
 
vehicles
 
(audio
 
system,
 
wipers,
 
l

ighting,
 ...

).
Ensure
 
that
 
the
 
jump
 
lead
 
cables
 
do
 
n

ot
 
pass
 
close
 
to
 
moving
 
parts
 
of
 
the
 
e

ngine
 
(cooling
 
fan,
 
belts,
 
...).
Do
 
not
 
disconnect
 
the
 
(+)
 
terminal
 
when
 
t

he
 
engine
 
is
 
running.
When
 
your
 
vehicle's
 
battery
 
is
 
discharged,
 
the
 e
ngine
 
can
 
be
 
started
 
using
 
a
 
slave
 
battery
 
(

external
 
or
 
on
 
another
 
vehicle)
 
and
 
jump
 
lead
 
c

ables
 
or
 
a
 
battery
 
booster.
F
 
R

aise
 
the
 
plastic
 
cover
 
on
 
the
 
(+)
 
terminal,
 
i

f
 
your
 
vehicle
 
has
 
one.
F
 
C

onnect
 
the
 
red
 
cable
 
to
 
the
 
positive
 
t

erminal
 
(+)
 
of
 
the
 
flat
 
battery
 
A (at
the
 
metal
 
elbow)
 
then
 
to
 
the
 
positive
 
t

erminal (+)
 
of
 
the
 
slave
 
battery
 
B or the
b o o s t e r.
F
 
C

onnect
 
one
 
end
 
of
 
the
 
green
 
or
 
black
 
c

able
 
to
 
the
 
negative
 
terminal
 
(-)
 
of
 
the
 
s

lave battery B or the booster (or earth
point
 
on
 
the
 
other
 
vehicle).
F
 
C

onnect
 
t

he
 
o

ther
 
e

nd
 
o

f
 
t

he
 
g

reen
 
o

r
 
b

lack
 
c

able to the earth point C
 
on
 
the
 
broken
 
d

own
 
vehicle. F
 
W
ait   until   the   engine   returns   to   idle   then  
d

isconnect   the   jump   lead   cables   in   the  
r

everse
 o
rder.
F
 
R
efit   the   plastic   cover   to   the   (+)   terminal,   if  
y

our   vehicle   has   one.
F
 
A
llow   the   engine   to   run   for   at   least  
3

0 minutes,   by   driving   or   with   the   vehicle  
s

tationary, so that the battery reaches an
adequate
  state   of   charge.
Some
  functions,   including   Stop   &   Start,  
a

re not available if the battery is not
sufficiently
 c

harged.
9
Practical information

166
C-elysee_en_Chap09_info-pratiques_ed01-2016
Charging the battery using
a battery charger
For optimum service life of the battery, it is essential   to   maintain   an   adequate   state   of  
c

harge.
In
  some   circumstances   it   may   be   necessary   to  
c

harge   the   battery:
-
 
i
f   you   use   your   vehicle   essentially   for   short  
j

ourneys,
-
 
i
f   the   vehicle   is   to   be   taken   off   the   road   for  
s

everal   weeks.
Contact
  a   CITROËN   dealer   or   a   qualified  
w

orkshop. Never
  try   to   charge   a   frozen   battery.
If the battery has been frozen, have
it
  checked   by   a   CITROËN   dealer   or   a  
q

ualified   workshop,   who   will   check   that  
t

he   internal   components   have   not   been  
d

amaged   and   the   casing   is   not   cracked,  
w

hich   could   cause   a   leak   of   toxic   and  
c

orrosive   acid.
If
  you   envisage   charging   your   vehicle's  
b

attery   yourself,   use   only   a   charger  
c

ompatible   with   lead-acid   batteries   of   a  
n

ominal   voltage   of   12   V.
If this label is present, it is essential
to
  use   only   a   12   V   charger,   to   avoid  
c

ausing   irreversible   damage   to   the  
e

lectrical   components   related   to   the  
S

top   &   Start   system. Follow
  the   instructions   for   use   provided  
b

y   the   manufacturer   of   the   charger.
Never
  reverse   polarities.
It
  is   not   necessary   to   disconnect   the  
b

attery.
F
 
S
witch   off   the   ignition.
F
 
S
witch   off   all   electrical   consumers   (audio  
s

ystem,   lighting,   wipers,   ...).
F
 
S
witch   off   the   charger   B   before   connecting  
t

he   cables   to   the   battery,   so   as   to   avoid   any  
d

angerous
 spar
ks.
F
 
E
nsure   that   the   charger   cables   are   in   good  
c

ondition.
F

R
aise the plastic cover, if your vehicle has
one,
  on   the   (+)   terminal.
F
 
C
onnect   the   charger   B   cables   as   follows:
-
 
t
he   positive   (+)   red   cable  
to
  the   (+)   terminal   of   the   battery   A,
-
 
t
he   negative   (-)   black   cable   to   the   earth  
p

oint C   on   the   vehicle.
F
 
A
t   the   end   of   the   charging   operation,   switch  
o

ff   the   charger   B   before   disconnecting   the  
c

ables   from   the   battery   A.
Practical information

167
C-elysee_en_Chap09_info-pratiques_ed01-2016
Disconnecting the (+) terminal
F Raise the lever A fully to release the clamp  B.
Reconnecting the (+) terminal
F Position   the   open   clamp   B of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   down   on   the   clamp   to   position   it  
c

orrectly   on   the   battery   post.
F
 
L
ock   the   clamp   by   lowering   the   lever   A.
Do
  not   force   the   lever   as   locking   will  
n

ot   be   possible   if   the   clamp   is   not  
p

ositioned   correctly;   start   the   procedure  
ag

ain.
Disconnecting the battery
In order to maintain an adequate state of   charge   for   starting   the   engine,   it   is  
r

ecommended   that   the   battery   be   disconnected  
i

f   the   vehicle   is   taken   out   of   service   for   a   long  
p

eriod.
Wait
  2   minutes   after   switching   off   the   ignition  
b

efore   disconnecting   the   battery:
F
 
c
lose   all   openings   (doors,   boot,   windows,  
r

oof),
F
 
s
witch   off   all   electrical   consumers   (audio  
s

ystem,   wipers,   lighting,   ...),
F
 
s
witch   off   the   ignition   and   wait   for  
f

our minutes.
Having
  exposed   the   battery,   it   is   only  
n

ecessary   to   disconnect   the   (+)   terminal.
Following reconnection of the
battery
After reconnecting the battery, switch on the ignition   and   wait   1   minute   before   starting   to  
a

llow   initialisation   of   the   electronic   systems.
However,
  if   minor   problems   persist   following  
t

his   operation,   contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Referring
  to   the   corresponding   section,   you  
m

ust   yourself   reinitialise   or   reset   certain  
s

ystems,   such   as:
-
 
t
he   remote   control,
-
 
t
he   date   and   time,
-
 
t
he   radio   preset   stations.
Quick release terminal
The Stop & Start system may not be operational   during   the   trip   following   the  
f

irst   engine   start.
In
  this   case,   the   system   will   only   be  
a

vailable   again   after   a   continuous  
p

eriod   of   immobilisation   of   the   vehicle,  
a

  period   which   depends   on   the   ambient  
t

emperature   and   the   state   of   charge   of  
t

he   battery   (up   to   about   8   hours).
9
Practical information

168
C-elysee_en_Chap09_info-pratiques_ed01-2016
System which manages the duration of use of certain functions to retain a sufficient level of
charge
  in   the   battery.
After
  the   engine   has   stopped,   you   can  
s

till   use   functions   such   as   the   audio   and  
t

elematics   system,   windscreen   wipers,   dipped  
b

eam   headlamps,   courtesy   lamps,   etc.   for  
a

  maximum   combined   duration   of   about  
t

hirty
 m
inutes.
Electrical energy economy mode
Switching to economy mode
Once this time has elapsed, a message appears   in   the   screen   indicating   that   the  
v

ehicle   has   switched   to   economy   mode   and   the  
a

ctive   functions   are   put   on   standby.
If
  a   telephone   call   is   being   made   at   this   time,  
it
  will   be   maintained   for   around   10   minutes   with  
t

he   Bluetooth   hands-free   system   of   your   audio  
s

ystem.
Exiting economy mode
These functions are reactivated automatically n ext   time   the   vehicle   is   driven.
F
 
T
o   restore   these   functions   immediately,  
s

tart   the   engine   and   let   it   run   for   at   least  
f

ive
 m
inutes.
A
  flat   battery   prevents   the   engine   from  
s

tarting   (refer   to   the   corresponding  
s

ection).
Load reduction mode
System which manages the use of certain functions   according   to   the   level   of   charge  
r

emaining   in   the   battery.
When
  the   vehicle   is   being   driven,   the   load  
r

eduction   function   temporarily   deactivates  
c

ertain   functions,   such   as   the   air   conditioning,  
t

he   heated   rear   screen...
The
  deactivated   functions   are   reactivated  
a

utomatically   as   soon   as   conditions   permit.
Practical information