boot Citroen C3 PICASSO 2008.5 1.G User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008.5, Model line: C3 PICASSO, Model: Citroen C3 PICASSO 2008.5 1.GPages: 204, PDF Size: 11 MB
Page 83 of 204
LAYOUT Storage tray
Opening
Lower the storage shelf.
P r e s s t h e fl a p o p e n i n g c o n t r o l .
L o w e r t h e fl a p .
Load the objects from inside the
boot.
Ski flap
Device for storing and transporting long
objects.
Side blinds may be available on the
sliding side doors.
Pull the side blind by the tab to install
it.
Always guide the blind slowly using the
tab, both when raising and when lower-
ing.
Side blinds
When unfolded, this provides a storage
area split into 2 sections.
Page 85 of 204
LAYOUT Storage tray
Opening
Lower the storage shelf.
P r e s s t h e fl a p o p e n i n g c o n t r o l .
L o w e r t h e fl a p .
Load the objects from inside the
boot.
Ski flap
Device for storing and transporting long
objects.
Side blinds may be available on the
sliding side doors.
Pull the side blind by the tab to install
it.
Always guide the blind slowly using the
tab, both when raising and when lower-
ing.
Side blinds
When unfolded, this provides a storage
area split into 2 sections.
Page 86 of 204
77
LAYOUT
BOOT LAYOUT
1. Storage net on left-hand boot trim.
2. Open storage compartments.
3. Torch.
4. M o v a b l e b o o t fl o o r .
5. Carrier bag hook
6. Securing rings.
7. Storage area under boot carpet
8. Luggage cover.
Page 87 of 204
i
78
LAYOUT
Movable boot floor
T h i s m o v a b l e b o o t fl o o r w i t h t w o p o s i -
tions allows you to:
- maximise the volume of the boot,
- partition the boot (storing of the rear shelf...),
- o b t a i n a fl a t fl o o r f r o m t h e b o o t opening to the front seats, when the
rear bench seat is in the retracted
position. P l a c i n g t h e m o v a b l e b o o t fl o o r i n
the low position
Press to release the handle located
at the boot opening.
U n l o c k t h e m o v a b l e b o o t fl o o r b y
lifting the handle.
M a n o e u v r e t h e m o v a b l e b o o t fl o o r
rearwards, then downwards, using
the handle, following the slides on
the sides.
Lock it by folding down the handle. P l a c i n g t h e m o v a b l e b o o t fl o o r i n
the high position
Press to release the handle.
U n l o c k t h e m o v a b l e b o o t fl o o r b y
lifting the handle.
Use the handle to manoeuvre the
m o v a b l e b o o t fl o o r r e a r w a r d s , t h e n
upwards to its high position.
Lock it by folding down the handle.
In the high position, the movable boot
fl o o r p e r m i t s s t o r i n g o f t h e r e a r s h e l f
and fragile objects.
T h e m o v a b l e b o o t fl o o r i s fi t t e d w i t h f o u r
stowing rings to secure your loads using
the net available as an accessory.
Ensure that your boot is empty
before handling the movable boot
fl o o r .
Page 88 of 204
79
LAYOUT
Hooks
The hooks permit the securing of shop-
ping bags. Load space cover
This consists of three sections.
T h e f r o n t s e c t i o n i s fl e x i b l e , a n d t h e
central and rear sections are rigid.
The rear section is secured to the tail-
gate by two cords.
To remove it from the boot:
unhook the two cords,
gently lift up the cover to remove it
f r o m i t s fi x i n g s ,
remove the cover.
It can be stored under the movable boot
fl o o r , i f t h i s i s i n i t s h i g h p o s i t i o n .
Page 125 of 204
i
113
PRACTICAL INFORMATION
CHANGING A WHEEL
The tools are installed under the boot
fl o o r .
To gain access to them:
open the boot,
r e m o v e t h e m o v a b l e b o o t fl o o r ,
lift up the boot carpet,
remove the box containing the
tools,
remove the polystyrene storage
b o x . A l l o f t h e s e t o o l s a r e s p e c i fi c t o y o u r
v e h i c l e . D o n o t u s e t h e m f o r o t h e r
p u r p o s e s .
1. W h e e l b r a c e .
Permits removal of the wheel trim a n d r e m o v a l o f t h e w h e e l fi x i n g
b o l t s .
2. J a c k w i t h i n t e g r a l h a n d l e .
P e r m i t s r a i s i n g o f t h e v e h i c l e .
3. " B o l t c o v e r " t o o l .
Permits removal of the bolt pro- t e c t o r s ( c o v e r s ) o n a l l o y w h e e l s .
List of tools
Other accessories
6. R e m o v a b l e t o w i n g e y e .
Refer to the paragraph "Towing the
v e h i c l e " .
Access to the tools
Wheel with trim
When removing the wheel , de-
t a c h t h e t r i m fi r s t u s i n g t h e w h e e l -
brace 1 pulling at the valve pas-
s a g e h o l e .
W h e n r e fi t t i n g t h e w h e e l , r e fi t t h e
trim starting by placing its notch fac-
ing the valve and press around its
e d g e w i t h t h e p a l m o f y o u r h a n d .
4. C e n t r i n g g u i d e .
P e r m i t s t h e r e fi t t i n g o f a n a l l o y w h e e l o n t h e h u b .
5. Socket for the anti-theft bolts (lo-
c a t e d i n t h e g l o v e b o x ) .
Permits adaptation of the wheel- brace to the special "anti-theft"
b o l t s .
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
v i d e d w i t h t h e v e h i c l e .
Page 133 of 204
121
PRACTICAL INFORMATION
Changing fog/reversing light bulbs
open the boot,
press on the tabs using 2 screwdrivers,
disconnect the light connector,
t u r n t h e b u l b h o l d e r b y a q u a r t e r
turn,
r e m o v e t h e b u l b a n d r e p l a c e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r . Changing the third stop light bulbs
(4 x W 5 W bulbs)
open the boot,
remove the two plugs located on the
boot inner panel,
press on the body of the light with
2 screwdrivers to remove it from its
housing,
turn the corresponding bulb-holder
a q u a r t e r t u r n ,
p u l l t h e b u l b a n d r e p l a c e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r . Changing the number plate light
bulbs (W 5 W)
insert a thin screwdriver into one of
the lens' exterior holes,
push it outwards to unclip,
remove the lens,
p u l l t h e b u l b a n d r e p l a c e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r .
Page 134 of 204
122
PRACTICAL INFORMATION
Interior lighting
Interior lamps (1/W 5 W)
D e t a c h t h e c o v e r o f t h e i n t e r i o r l a m p 1
with a thin screwdriver, close to the but-
t o n , t o a c c e s s t h e f a u l t y b u l b .
Map reading lamps (2/W 5 W)
D e t a c h t h e c o v e r o f t h e i n t e r i o r l a m p . T o
access the faulty bulb, detach the par-
tition for the reading lamp 2 concerned,
a s n e c e s s a r y . Footwell lamps (W 5 W)
Unclip the cover using a thin screwdriver
t o a c c e s s t h e f a u l t y b u l b .
Boot lamps (W 5 W)
D e t a c h t h e u n i t b y p u s h i n g i t r e a r w a r d s . Torch (Krypton 3.6 V)
O p e n t h e t a b .
P u s h w i t h a fl a t s c r e w d r i v e r i n t h e
hole under the tab and recover the
b u l b u n i t .
Open the bulb unit fully to change
t h e b u l b .
Exterior mirror lamps (W 5 W)
Unclip the cover using a thin screwdriver
t o a c c e s s t h e f a u l t y b u l b .
Page 145 of 204
i!
132
PRACTICAL INFORMATION
TOWING THE VEHICLE
Access to the tools Towing your vehicle
On the front bumper, unclip the cov-
e r b y p r e s s i n g a t t h e b o t t o m .
S c r e w t h e t o w i n g e y e i n f u l l y .
I n s t a l l t h e t o w b a r .
Switch on the hazard warning lights
o n t h e t o w e d v e h i c l e .
P l a c e t h e g e a r l e v e r i n n e u t r a l .
On the rear bumper, unclip the cover
b y p r e s s i n g a t t h e b o t t o m .
S c r e w t h e t o w i n g e y e i n f u l l y .
I n s t a l l t h e t o w b a r .
Switch on the hazard warning lights
o n t h e t o w e d v e h i c l e .
Towing another vehicle
The towing eye is installed under the
b o o t fl o o r .
To gain access to it:
open the boot,
r e m o v e t h e m o v a b l e b o o t fl o o r ,
lift up the boot carpet,
remove the towing eye from the tool
h o l d e r . When towing with all four wheels
on the ground, always use a tow-
b a r .
When towing with only two wheels
on the ground, always use profes-
s i o n a l l i f t i n g e q u i p m e n t .
When towing with the engine off,
there is no longer any braking or
s t e e r i n g a s s i s t a n c e .
Failure to observe this special con-
dition could result in damage to
certain braking components and
the absence of braking assistance
t h e n e x t t i m e t h e e n g i n e i s s t a r t e d .
Procedure for having your vehicle towed
or for towing another vehicle using a re-
m o v a b l e t o w i n g e y e .
Page 148 of 204
i
!
135
PRACTICAL INFORMATION
ACCESSORIES
You can obtain a wide range of accessories and genuine parts from the CITROËN
n e t w o r k .
T h e y a l l b e n e fi t f r o m t h e C I T R O Ë N w a r r a n t y a n d r e c o m m e n d a t i o n .
These accessories and parts, having been tested and approved f or reliability and
s a f e t y , a r e a l l a d a p t e d t o y o u r C I T R O Ë N v e h i c l e .
The product range offered by Accessories is structured around 5 categ ories:
P R O T E C T I O N - T O U R I N G - I N - C A R T E C H N O L O G Y - S T Y L I N G - U N I V E R S A L .
"Styling":
seat covers compatible with side air
bags, aluminium gear lever knob, fog
l a m p s , s u n r o o f , d o o r d e fl e c t o r s , s p o i l e r ,
styling strips, alloy wheels, trims, sport
e x h a u s t , b o d y w o r k k i t . . .
"Protection":
anti-theft alarm, window engraving,
w h e e l l o c k s , fi r s t a i d k i t , w a r n i n g t r i a n -
gle, safety jacket, stolen vehicle track-
i n g s y s t e m , d o g g u a r d , s n o w c h a i n s . . .
* To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned and secured correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
"In-car technology":
Bluetooth
®
hands free kit, audio sys-
tems, portable navigation system,
a u x i l i a r y a u d i o c a b l e ( e . g . f o r a n M P 3
connection), loudspeakers, USB Box,
p o r t a b l e v i d e o s c r e e n . . .
"Touring":
mats * , boot tray, sun blinds, roof bars,
towbar, bicycle carrier, ski carrier, dog
guard, luggage net, booster seats and
c h i l d s e a t s . . . "Universal":
screenwash, interior and exterior main-
t e n a n c e a n d c l e a n i n g p r o d u c t s .
D e p e n d i n g o n t h e c o u n t r y i n w h i c h
the vehicle is sold, it is compulsory
to have a safety jacket, warning tri-
angle and spare bulbs available in
t h e v e h i c l e .
T h e fi t t i n g o f e l e c t r i c a l e q u i p m e n t
or accessories which are not rec-
ommended by CITROËN may re-
sult in a failure of your vehicle's
e l e c t r o n i c s y s t e m .
P l e a s e n o t e t h i s s p e c i fi c w a r n -
i n g . Y o u a r e a d v i s e d t o c o n t a c t
a CITROËN representative to be
shown the range of recommended
e q u i p m e n t a n d a c c e s s o r i e s .