ignition Citroen C4 2016 2.G Service Manual

125
C4-2_en_Chap04_eclairage-et-visibilite_ed02-2015
Model without AUTO lighting
Model with AUTO lighting
A. Main  lighting   mode   selection   ring:   turn   it  t
o   position   the   symbol   required   facing   the  
ma

rk.
Manual controls
Lighting off (ignition off) /
D aytime   running   lamps   (engine   running).
Automatic illumination of headlamps.
B.
 S

talk
 
for   switching   headlamps:   pull  
t

he
 
stalk   towards   you   to   switch   the  
l

ighting   between   dipped   and   main   beam  
h

eadlamps.
In
 
the
 
lamps   off   and   sidelamps   modes,   the  
d

river
 
can
  switch   on   the   main   beam   headlamps  
t

emporarily   ("headlamp   flash")   by   maintaining   a  
p

ull
 
on
 
the   stalk.
Sidelamps.
Dipped
  headlamps   or   main   beam  
h

eadlamps.
Displays
The lighting is controlled directly by the driver by   means   of   the   ring   A   and   the   stalk   B. Illumination
  of   the   corresponding   indicator  l
amp   in   the   instrument   panel   confirms   that   the  
l

ighting   selected   is   on.
4
Lighting and visibility

127
C4-2_en_Chap04_eclairage-et-visibilite_ed02-2015
In good or rainy weather, by both day and   night,   the   front   foglamps   and   the  
r

ear   foglamps   are   prohibited.   In   these  
s

ituations,   the   power   of   their   beams  
m

ay   dazzle   other   drivers.   They   should  
o

nly   be   used   in   fog   or   falling   snow.
In these weather conditions, you should
switch
  on   the   foglamps   and   dipped  
b

eam   headlamps   manually,   as   the  
s

unshine   sensor   may   detect   sufficient  
l

ight.
Do
  not   forget   to   switch   off   the   front   and  
r

ear   foglamps   when   they   are   no   longer  
n

ecessary.Switching off the lighting when
switching off the ignition
When the ignition is switched off, all of the lamps   switch   off   immediately,   except   for t

he   dipped   beam   headlamps   if   automatic
 g

uide-me-home   lighting   is   activated.
Switching on the lighting
when switching on the
ignition
To reactivate the lighting control stalk, turn   the   ring   A to position "0"  -   lighting  
o

ff,   then   to   the   position   of   your   choice.
When
  the   driver's   door   is   opened,   a  
t

emporary   audible   signal   warns   you   that  
t

he   vehicle's   lighting   is   on.
They
  switch   off   automatically   after   a  
p

eriod which depends on the state of
charge
  of   the   battery   (entry   to   energy  
ec

onomy
 mo
de).
4
Lighting and visibility

128
C4-2_en_Chap04_eclairage-et-visibilite_ed02-2015
Parking lamps
F Depending  on   version,   within   one   minute  o
f   switching   off   the   ignition,   operate   the  
l

ighting   control   stalk   up   or   down   depending  
o

n   the   traffic   side   (for   example:   when  
p

arking   on   the   left;   lighting   control   stalk  
u

pwards;   the   right   hand   sidelamps   are   on).
This
  is   confirmed   by   an   audible   signal   and  
i

llumination   of   the   corresponding   direction  
i

ndicator   warning   lamp   in   the   instrument   panel.
To
  switch   off   the   parking   lamps,   return   the  
l

ighting   control   stalk   to   the   central   position.
Manual guide-me-home
lighting
The temporary illumination of the dipped beam headlamps   after   the   vehicle's   ignition   has   been  
s

witched   off   makes   the   driver's   exit   easier  
w

hen   the   light   is   poor.
Switching on
F With  the   ignition   off,   "flash"   the   headlamps  u
sing   the   lighting   stalk.
F
 
A
  further   "headlamp   flash"   switches   the  
f

unction   off.
Switching off
The manual guide-me-home lighting switches off   automatically   after   a   set   time.Side
  markers   for   the   vehicle   by   illumination   of  
t

he   sidelamps   on   the   traffic   side   only.
Daytime running lamps
Daytime lighting which comes on automatically w
hen   the   engine   is   started   making   the   vehicle  
m

ore   visible   to   other   users.
This
  function   is   assured   by   dedicated   lamps.
Lighting and visibility

130
C4-2_en_Chap04_eclairage-et-visibilite_ed02-2015
Switching off
The welcome lighting switches off automatically after   a   programmed   time,   when   the   ignition   is  
s

witched   on   or   on   locking   the   vehicle.
Welcome lighting
Switching on
F Press  the   open   padlock   on   the  r
emote   control   or   one   of   the   front  
d

oor handles with the "Keyless
Entry
  and   Starting"   system.
The
 
remote   switching   on   of   the   lighting   makes  
y

our
 
access   to   the   vehicle   easier   in   poor   light.  
I

t
 
is
 
activated   depending   on   the   ambient   light  
l

evel
 
detected   by   the   sunshine   sensor.
The
 
sidelamps   and   dipped   beam   headlamps,  
a

s
 
well
 
as
  the   side   spotlamps,   located   under  
t

he
 
door
 
mirrors,   come   on;   your   vehicle   is   also  
u

nlocked.
Programming
Activation or deactivation, as well as
the   duration   of   the   lighting   duration  
f

or   the   welcome   lighting   can   be   set  
v

ia   the   vehicle   configuration   menu.
Automatic guide-me-home
lighting
When the automatic illumination of headlamps functions   is   activated,   if   the   ambient   light   level  
i

s   low   the   dipped   beam   headlamps   remain   on  
w

hen   switching   off   the   ignition.
Settings
Activation and deactivation, as
well  as   the   duration   of   the   guide-
me-home
  lighting   can   be   set   in   the  
v

ehicle   configuration   menu.
Lighting and visibility

133
C4-2_en_Chap04_eclairage-et-visibilite_ed02-2015
Directional lighting
Programming
with directional lighting
without directional lighting
When
 
the
 
dipped
 
or
 
main
 
beam
 
headlamps
 
a

re
 
on,
 
this
 
function,
 
allows
 
the
 
light
 
beams
 
to
 
b

etter
 
follow
 
the
 
road.
The use of this function, coupled with the
xenon
 
headlamps
 
and
 
the
 
cornering
 
lighting,
 
c

onsiderably
 
improves
 
the
 
quality
 
of
 
your
 
l

ighting
 r

ound
 b

ends.
Operating fault
If a fault occurs, this warning lamp f lashes   in   the   instrument   panel,  
a

ccompanied   by   a   message   in   the  
sc

reen.
Contact
 
a
  CITROËN   dealer   or   a   qualified  
w

orkshop.
This
 
function   is   inactive:
-

w

hen stationary or at low speeds,
-
 w

hen
 r
everse
 i
s
 enga
ged.
The   system   is   activated   or  
d

eactivated in the vehicle
configuration
 m
enu.
 T

he
 
system   is   activated   by   default.
The
 
state
 
of   the   system   stays   in   memory   on  
s

witching
 
off   the   ignition.
4
Lighting and visibility

136
C4-2_en_Chap04_eclairage-et-visibilite_ed02-2015
Automatic rain sensitive
windscreen wipers
Briefly push stalk A downwards.
Switching onSwitching off
Briefly push stalk A downwards
ag ain.
The
  automatic   rain   sensitive  
w

indscreen   wipers   must   be   reactivated  
i

f
 
the   ignition   has   been   off   for   more   than  
o

ne minute.
The
 
instruction
 
is
 
confirmed
 
by
 
a
 
wiping
 
cycle,
 
a

ccompanied
 
by
 
illumination
 
of
 
this
 
warning
 
l

amp
 
in
 
the
 
instrument
 
panel
 
and
 
an
 
activation
 
m

essage. The
 
instruction   is   confirmed   by   this   warning  
l

amp
 
going   off   in   the   instrument   panel   and/or  
t

he
 
display   of   a   deactivation   message.
The
 
windscreen
 
wipers
 
operate
 
automatically,
 
w

ithout any action on the part of the driver, if
rain
 
is
 
detected
 
(sensor
 
behind
 
the
 
rear
 
view
 
m

irror),
 
adapting
 
their
 
speed
 
to
 
the
 
intensity
 
of
 
t

he
 
rainfall.
Operating fault
If an automatic rain sensitive wiper malfunction o
ccurs,   the   wipers   will   operate   in   intermittent  
m

ode.
Contact
  a   CITROËN   dealer   or   a   qualified  
w

orkshop. Do
  not   cover   the   rain   sensor,   linked   with
 t

he sunshine sensor and located in the
centre of the windscreen behind the rear
view
  mirror.
Switch
  off   the   automatic   rain   sensitive
 w

ipers   when   using   an   automatic   car   wash.
In winter, it is advisable to wait until the
windscreen
  is   completely   clear   of   ice
 b

efore   activating   the   automatic   rain
 sen

sitive
 w
ipers.
Lighting and visibility

137
C4-2_en_Chap04_eclairage-et-visibilite_ed02-2015
Special position of the
windscreen wipers
This position permits release of the windscreen wiper   blades.
It
  is   used   for   cleaning   or   replacement   of   the  
b

lades.   It   can   also   be   useful,   in   winter,   to  
d

etach   the   blades   from   the   windscreen.
F
 
A
ny   action   on   the   wiper   stalk   in   the   minute  
a

fter   switching   off   the   ignition   places   the  
b

lades   vertically   on   the   screen.
F
 
T
o   park   the   blades   again,   switch   on   the  
i

gnition   and   operate   the   wiper   stalk.To
  maintain   the   effectiveness   of   the   flat  
w

iper   blades,   it   is   advisable   to:
-
 
h
andle   them   with   care,
-
 
c
lean   them   regularly   using   soapy  
w

ater,
-
 
a
void   using   them   to   retain  
c

ardboard on the windscreen,
-
 
r
eplace   them   at   the   first   signs   of  
w

e a r.
Windscreen and headlamp
wash
Low screenwash / headlamp
wash fluid level
On vehicle fitted with headlamp washers, the low   level   of   this   fluid   is   indicated   by   gauge   in  
t

he   reservoir   filler   neck   under   the   bonnet.
Checking
  and   topping   up   this   fluid   can   should  
b

e   done   with   the   engine   off.
The
  level   of   this   fluid   should   be   checked  
r

egularly,
 par
ticularly
 d
uring
 w
inter.
For
  more   information   on   checking   the  
s

creenwash   /   headlamp   wash   level,   refer   to   the  
c

orresponding
 s
ection.
F
 
P
ull   the   windscreen   wiper   stalk   towards  
y

ou.   The   windscreen   wash   then   the  
w

indscreen   wipers   operate   for   a   fixed  
p

eriod.
The   headlamp   washers   only   operate   when   the
dipped or main beam headlamps are on , with
the vehicle moving .
To   reduce   the   consumption   of   the   fluid  
b

y   the   headlamp   washers,   they   operate  
o

nly with every seventh use of the
screenwash   or   every   25   miles   (40   km)  
d

uring   a   given   journey.
4
Lighting and visibility

139
C4-2_en_Chap05_securite_ed02-2015
Hazard warning 
lam
ps
Visual warning by means of the direction i
ndicators to alert other road users to a vehicle
breakdown,
  towing   or   accident.
F

P
ress this button, the direction indicators
flash.
They
  can   operate   with   the   ignition   off.
Automatic operation of
hazard warning lamps
When braking in an emergency, depending on the   deceleration,   the   hazard   warning   lamps  
c

ome   on   automatically.
They
  switch   off   automatically   the   first   time   you  
a

ccelerate.
F
 
Y
ou   can   also   switch   them   off   by   pressing  
t

he   button.
Horn
Audible warning system to alert other road users   to   an   imminent   danger.
F
 
P
ress   the   central   part   of   the   multifunction  
s

teering
 w
heel.
Use
  the   horn   moderately   and   only   in  
s

ituations   allowed   by   the   motoring  
r

egulations   in   the   country   you   are  
d

riving   in.
Emergency or 
a

ssistance call
This system allows you to make an emergency o
r   assistance   call   to   the   emergency   services   or  
t

o   the   dedicated   CITROËN   service.
For
  more   information   on   the   use   of   this  
f

unction,   refer   to   the   "Audio   and   telematics"  
s

ection.
5
Safety

142
C4-2_en_Chap05_securite_ed02-2015
Reactivation
These systems are reactivated automatically each   time   the   ignition   is   switched   back   on   or  
f

rom   30   mph   (50   km/h).
F
 
P
ress   this   button   again   to   reactivate   them  
m

anually.
The
  illumination   of   the   indicator  
l

amps   in   the   instrument   panel   and  
i

n   this   button,   accompanied   by   an  
a

udible   signal   and   a   message   in   the  
s

creen, indicates a fault with these
systems.
Operating fault
The trajectory control systems offer i ncreased   safety   in   normal   driving,   but  
t

his   should   not   encourage   the   driver   to  
t

ake   extra   risks   or   drive   at   high   speed.
The
  correct   functioning   of   these  
s

ystems   is   assured   provided   that  
m

anufacturer's   recommendations   are  
ob

served
 on
:
-
 
w
heels   (tyres   and   rims),
-
 
b
raking   components,
-
 el

ectronic
 c
omponents,
-
 
a
ssembly   and   repair   procedures.
After
  an   impact,   have   these   systems  
c

hecked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
q

ualified
 w

orkshop.
Safety

143
C4-2_en_Chap05_securite_ed02-2015
F To  lower   the   attachment   point,   squeeze   the  c
ontrol A   and   slide   it   downwards.
F
 
T
o   raise   the   attachment   point,   slide   the  
c

ontrol A  
up
wards.
Height adjustment
Seat belts
Front seat belts
The front seat belts are fitted with a
pretensioning  and   force   limiting   system.
This
  system   improves   safety   in   the   front  
s

eats   in   the   event   of   a   front   or   side   impact.  
D

epending   on   the   severity   of   the   impact,   the  
p

retensioning   system   instantly   tightens   the   seat  
b

elts   against   the   body   of   the   occupants.
The
  pretensioning   seat   belts   are   active   when  
t

he   ignition   is   on.
The
  force   limiter   reduces   the   pressure   of   the  
s

eat belt on the chest of the occupant, so
improving
  their   protection.Fastening
F Pull  the   strap,   then   insert   the   tongue   in   the  buc
kle.
F
 
C
heck   that   the   seat   belt   is   fastened  
c

orrectly   by   pulling   the   strap.
Unfastening
F Press  the   red   button   on   the   buckle.
F  G uide   the   seat   belt   as   it   reels   in.
5
Safety