engine Citroen C4 2016 2.G Repair Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2016, Model line: C4, Model: Citroen C4 2016 2.GPages: 396, PDF Size: 10.22 MB
Page 186 of 396
184
C4-2_en_Chap06_conduite_ed02-2015
These two special programmes supplement the automatic operation in very specific conditions
o
f use.
Sport programme "S"
F Press button "S" , after starting the engine.
The gearbox automatically favours a dynamic
s
tyle of driving.
S
appears in the instrument panel.
Snow programme "T"
F Press button " T", after starting the engine.
The gearbox adapts to driving on slippery
r
oads.
This
programme improves starting and drive
w
hen traction is poor.
T
appears in the instrument panel.F
A
t any time, press the button selected
a
gain to leave the special programme
e
ngaged and return to auto-adaptive mode.
Sport and snow
programmes
Return to auto-adaptive
mode
Driving
Page 187 of 396
185
C4-2_en_Chap06_conduite_ed02-2015
Manual operation
D disappears and the gears engaged appear in succession on
t
he instrument panel.
Invalid value during manual
operation
This symbol is displayed if a gear is not engaged correctly (selector
b
etween two positions).
Stopping the vehicle
If the selector is not in position P ,
when the driver's door is opened or
a
pproximately 45 seconds after the
i
gnition is switched off, there is an
a
udible signal and a message appears.
F
R
eturn the selector to position P ;
t
he audible signal stops and the
m
essage
d
isappears.
F
Sel
ect position M for sequential
c
hanging
o
f
the
six
gears.
F
P
ush the selector towards the +
sign
to
c
hange
up
a
gear.
F
P
ull the selector towards the -
sign
to
c
hange
down
a
gear.
It
is
only
possible
to
change
from
one
gear
to
a
nother
if
the
vehicle
speed
and
engine
speed
p
ermit;
other wise,
the
gearbox
will
operate
t
emporarily
in
automatic
mode.
If
the
engine
speed
is
too
low
or
too
high,
the
g
ear
selected
flashes
for
a
few
seconds,
then
t
he
actual
gear
engaged
is
displayed.
When
the
vehicle
is
stationary
or
moving
v
ery
slowly,
the
gearbox
selects
gear
1
automatically.
It is not necessary to release the accelerator
when
c
hanging
g
ear.
It
is
possible
to
change
from
position
D
(automatic)
to
position
M
(manual)
at
any
time.
The
sport
and
snow
programmes
do
not
o
perate
in
manual
mode. Before
s
witching
o
ff
t
he
e
ngine,
p
ut
t
he
s
elector
i
n position P or N to place the gearbox in
neu
tral.
In
both cases, apply the parking brake to
i
mmobilise the vehicle, unless it is programmed
t
o
automatic mode.
6
Driving
Page 189 of 396
187
C4-2_en_Chap06_conduite_ed02-2015
Gear shift indicator*
Depending on the driving situation and your vehicle's equipment, the system may advise
y
ou to skip one (or more) gear(s). You can
f
ollow this instruction without engaging the
i
ntermediate
g
ears.
The
gear engagement recommendations must
n
ot be considered compulsory. In fact, the
c
onfiguration of the road, the amount of traffic
a
nd safety remain determining factors when
c
hoosing the best gear. Therefore, the driver
r
emains responsible for deciding whether or not
t
o follow the advice given by the system.
This
function cannot be deactivated. -
Y
ou press the accelerator pedal.
Example:
-
Y ou are in third gear.
-
T
he system may suggest that you engage
a
higher gear.
The
information appears in the instrument
p
anel in the form of an arrow.
System
which reduces fuel consumption by recommending the most appropriate gear.
With an automatic gearbox, the system is only
a
ctive in manual mode.
* Depending
on engine.
On
vehicle fitted with a manual gearbox,
t
he arrow may be accompanied by the gear
re
commended. The
system adapts its gear change
r
ecommendation according to the
d
riving conditions (slope, load, ...) and
t
he demands of the driver (power,
a
cceleration, braking, ...).
The
system never suggests:
-
e
ngaging first gear,
-
enga
ging
r
everse
g
ear.
Operation
On BlueHDi Diesel 150 versions with
manual gearbox, the system may
s
uggest changing into neutral so that
t
he engine can go into standby (STOP
m
ode with Stop & Start), in certain
d
riving conditions. In this case, N is
displayed
in the instrument panel.
6
Driving
Page 190 of 396
188
C4-2_en_Chap06_conduite_ed02-2015
Stop & Start
Operation
Going into engine STOP mode
The "ECO" warning lamp comes on i
n the instrument panel and the engine g
oes into standby automatically:
-
w
ith a manual gearbox , at speeds below
12
m
ph
(
20
k
m/h),
o
r
v
ehicle
s
tationary
w
ith
P
ureTech 130 petrol and BlueHDi 115 and
1
20
Diesel versions, when you put the gear
l
ever into neutral and release the clutch
pedal,
If your vehicle is fitted with the
system,
a time counter calculates
t
he sum of the periods in STOP
m
ode during a journey. It resets
i
tself to zero every time the
i
gnition is switched on with the
k
ey or the "START/STOP" button.
-
w
ith an automatic gearbox, vehicle
stationary,
when you press the brake pedal
o
r
place the gear selector in position N.
Special cases: STOP mode
unavailable
STOP mode is not invoked when:
- t he vehicle is on a steep slope (up or
d
ow n),
-
t
he driver's door is open,
-
t
he driver's seat belt is not fastened,
-
t
he vehicle has not exceeded 6 mph
(
10 km/h) since the last engine start (using
t
he key or the "START/STOP" button),
-
t
he electric parking brake is applied or
be
ing
a
pplied,
-
t
he engine is needed to maintain a
c
omfortable temperature in the passenger
c
ompartment,
-
d
emisting is active,
-
s
ome special conditions (battery charge,
e
ngine temperature, braking assistance,
a
mbient temperature...) where the engine is
n
eeded to assure control of a system.
In this case, the "ECO"
warning lamp
f
lashes for a few seconds, then goes
o
f f.
This operation is perfectly normal.
The
Stop
&
Start system
puts
the
engine
temporarily
into
standby
-
STOP
mode
-
during
stops
in
the
traffic (red lights, traffic jams, or other...). The
e
ngine
restarts
automatically
-
START
mode
-
as
soon
as
you
want
to
move
off.
The
restart
takes
place
instantly, quickly and silently.
Per fect
for
urban
use,
the
Stop
&
Start
system
reduces
fuel
consumption
and
exhaust
emissions
as
well
as the noise level when stationary.
Never
refuel
with
the
engine
in
STOP
m
ode;
you
must
switch
off
the
ignition
w
ith
the
key
or
the
"START/STOP"
b
utton.
STOP
mode
does
not
affect
the
f
unctionality of the vehicle, such as
braking,
power
steering,
for
example.
Driving
Page 191 of 396
189
C4-2_en_Chap06_conduite_ed02-2015
Deactivation
Going into engine START mode
At any time, press the "ECO OFF" switch to
d eactivate the system.
This
is confirmed by the switch warning lamp
c
oming on accompanied by the display of a
m
essage.
Special cases: START invoked
automatically
The "ECO" warning lamp goes off a
nd the engine starts automatically:
-
w
ith a manual gearbox , when you fully
depress the clutch pedal,
-
w
ith an automatic gearbox:
●
g
ear selector in position D or M, when
you
release the brake pedal,
●
o
r
gear selector in position N and brake
p
edal released, when you place the gear
s
elector in position D or M ,
●
o
r
when you engage reverse gear.For
safety reasons or to ensure smooth o
peration, START mode is invoked
a
utomatically
w
hen:
-
y
ou open the driver's door,
-
y
ou unfasten the driver's seat belt,
-
t
he speed of the vehicle exceeds 15 mph
(
25 km/h) with a manual gearbox (3 km/h
(
2 mph) with PureTech 130 petrol and
B
lueHDi Diesel 115 and 120 versions) or
2 m
ph (3 km/h) with an automatic gearbox,
-
t
he electric parking brake is being applied,
-
s
ome special conditions (battery charge,
e
ngine temperature, braking assistance,
a
mbient temperature...) where the engine is
n
eeded to assure control of a system.
In this case the "ECO"
warning lamp
f
lashes for few seconds, then goes
o
f f.
This operation is perfectly normal.
With
a manual gearbox in STOP mode,
i
f
a
gear is engaged without fully
d
epressing the clutch pedal, a warning
l
amp comes on or an alert message
i
s
displayed asking you to depress the
c
lutch pedal to restart the engine. If
the system has been deactivated
i
n STOP mode, the engine restarts
i
mmediately.
6
Driving
Page 192 of 396
190
C4-2_en_Chap06_conduite_ed02-2015
Maintenance
In the event of a malfunction with the system, the "ECO OFF" switch warning lamp flashes,
t
hen comes on continuously.
have
it checked by a CITROËN dealer or a
q
ualified
w
orkshop.
Operating fault
This system requires the use of a 12 V battery of specific technology and characteristics
(
reference numbers available from a CITROËN
d
ealer or a qualified workshop).
Fitting
a battery not listed by CITROËN would
i
ntroduces the risk of faults with the system.
Before
doing any work under the
b
onnet, deactivate the Stop & Start
system to avoid the risk of injury related
t
o an automatic change to START
m
ode.
The Stop & Start system makes use of
a
n advanced technology. All work on
t
his type of battery must only be carried
o
ut by a CITROËN dealer or a qualified
w
orkshop.
In
the
event
of
a
fault
in
STOP
mode,
t
he
vehicle
may
stall.
All
of
the
i
nstrument
panel
warning
lamps
come
o
n.
Depending
on
version,
an
alert
m
essage
may
also
be
displayed
asking
y
ou
to
put
the
gear
lever
into
position
N
and
put
your
foot
on
the
brake
pedal.
It is then necessary to switch off the
ignition,
then
restart
the
engine
using
t
he
key
or
the
"START/STOP"
button.
Reactivation
The system is reactivated automatically a t every new start using the key or the
"
START/STOP" button.
Press the "ECO OFF"
switch again.
The
system is active again; this is confirmed
b
y
the
switch warning lamp going off and the
d
isplay of a message.
Driving
Page 193 of 396
191
C4-2_en_Chap06_conduite_ed02-2015
Hill start assist
On an ascending slope, with the vehicle
stationar y, the vehicle is held for a brief
moment when you release the brake pedal:
-
i
f you are in first gear or neutral with a
m
anual
g
earbox,
-
i
f you are in position D or M with an
automatic
gearbox.
Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held for a brief moment when you
release the brake pedal.
Operating fault
If a fault occurs with the system, these warning lamps come on. Contact a CITROËN dealer
o
r a qualified workshop to have the system
c
hecked.
System
which
keeps
your
vehicle
immobilised
t
emporarily
(approximately
2
seconds)
when
s
tarting
on
a
gradient,
the
time
it
takes
to
m
ove
your
foot
from
the
brake
pedal
to
the
a
ccelerator
ped
al.
This
function
is
only
active
when:
-
t
he
vehicle
is
completely
stationary,
with
y
our
foot
on
the
brake
pedal,
-
w
hen
certain
conditions
of
gradient
are
m
et,
-
w
ith
the
driver’s
door
closed.
The hill start assist function cannot be
deactivated.
Do
not
leave
the
vehicle
while
it
is
being
h
eld
in
the
hill
start
assist
phase.
If you need to leave the vehicle while
the
engine
is
running,
apply
the
parking
b
rake
manually
then
ensure
that
the
p
arking
brake
warning
lamp
is
on
(not
f
lashing)
in
the
instrument
panel.
6
Driving
Page 196 of 396
194
C4-2_en_Chap06_conduite_ed02-2015
Lane departure warning system
Activation
Deactivation
DetectionOperating fault
System which detects the involuntary crossing o
f longitudinal traffic lane markings on the
g
round (solid or broken line).
Sensors,
fitted below the front bumper, trigger
a
warning if the vehicle drifts over a lane
m
arking (speed higher than 50 mph (80 km/h)).
This
system is particularly useful on motor ways
a
nd main roads. In
the event of a malfunction, the
s
ervice warning lamp comes on,
a
ccompanied by an audible signal
a
nd a message in the screen.
Contact a CITROËN dealer or a qualified
w
orkshop.
The lane departure warning system
c
annot in any circumstances replace
t
he need for vigilance on the part of the
d
river.
It
is necessary to observe driving
r
egulations and take a break every
t
wo hours. The
detection may be impeded:
- i f the sensors are dirty (mud, snow...),
-
i
f the markings on the ground are
w
orn,
-
i
f there is little contrast between the
markings
on the ground and the
r
oad sur face.
You
are warned by the vibration of the driver's
s
eat cushion:
-
o
n the right-hand side, if the marking on
t
he ground has been crossed on the right,
-
o
n the left-hand side, if the marking on the
g
round has been crossed on the left.
No
warning is transmitted while the direction
i
ndicator is active and for approximately
2
0 seconds after the direction indicator is
switched
off.
A
warning may be transmitted if a direction
m
arking (e.g. arrow) or non-standard marking
(
e.g. graffiti) is crossed.
F
W
hen switching the ignition on or with
t
he engine running, press this button; the
i
ndicator lamp comes on.
F
P
ress this button again, the indicator lamp
g
oes off.
The status of the system remains in the m
emory when the ignition is switched off.
Driving
Page 197 of 396
195
C4-2_en_Chap06_conduite_ed02-2015
Blind spot sensors
This driving assistance system warns the driver of the presence of another vehicle in the blind
spot
angle of their vehicle (areas masked from
t
he driver's field of vision), as soon as this
p
resents a potential danger.
Operation
F On switching on the ignition, or engine r
unning, press this button to activate the
f
unction; the warning lamp comes on.
Sensors
fitted in the front and rear bumpers
m
onitor the blind spots.
A
warning
lamp
appears
in
the
door
mirror
on
t
he
side
in
question:
-
i
mmediately,
when
being
overtaken,
-
a
fter a delay of about one second, when
overtaking
a
vehicle
slowly.
This
system
is
designed
to
improve
s
afety
when
driving
and
is
in
no
c
ircumstances
a
substitute
for
the
use
o
f
the
interior
rear
view
mirror
and
door
m
irrors.
It
is
the
driver's
responsibility
to
c
onstantly
check
the
traffic,
to
assess
t
he distances and relative speeds
of other vehicles and to predict their
movements
before
deciding
whether
to
c
hange
lan
e.
The
blind
spot
sensor
system
can
never
r
eplace
the
need
for
vigilance
on
the
p
art
of
the
driver.
6
Driving
Page 210 of 396
208
C4-2_en_Chap07_infos-pratiques_ed02-2015
TOTAL & CITROËN
Partners in performance and
protecting the environment
Innovation in the search for
performance
For over 40 year, the TOTAL Research and
Development departments h ave d eveloped l
ubricants for CITROËN, to match the latest
t
echnical innovations on CITROËN vehicles, both for
competition
and for everyday motoring.
For you, this is an assurance that you will obtain the
best
per formance from your engine.
Optimum protection for
your engine
By having your CITROËN vehicle serviced with TOTAL lubricants, you are
contributing
towards improving the life
a
nd per formance of your engine, while
a
lso protecting the environment.
Practical information