Citroen C5 DAG 2010.5 (RD/TD) / 2.G Owner's Manual
Manufacturer: CITROEN, Model Year: 2010.5, Model line: C5 DAG, Model: Citroen C5 DAG 2010.5 (RD/TD) / 2.GPages: 336, PDF Size: 18.85 MB
Page 151 of 336
IX
!
130
D R I V I N G
On sloping ground: immobilise
the vehicle by placing the chocks
(if your vehicle has them) in front
or behind the two front wheels,
against the slope
On level ground: immobilise the vehicle by placing the chocks
(if your vehicle has them) in
front and behind one of the front
wheels.
Open the lower compartment of
the centre armrest by pulling it.
Ensure that the cup holder B is
folded away.
Remove the rubber mat covering
the base of the armrest. This strap does not permit
application of the parking
brake.
To re-engage the electric parking
brake (after rectifying the malfunc-
tion or battery failure), give a long
pull on the control A until the park-
i n g b r a k e w a r n i n g l a m p ( ! ) fl a s h e s
on the instrument panel then give a
second long pull until this warning
l a m p i s o n fi x e d .
The time required for the subse-
quent application may be longer
than during normal operation.
It is essential that the ignition is
not switched on until the parking
b r a k e h a s r e - e n g a g e d ( fl a s h i n g o f
the warning lamp (!) on the instru-
ment panel then the warning lamp
o n fi x e d ) t o a v o i d d a m a g e t o t h e
parking brake.
Take care not to allow moisture or
d u s t i n t h e p r o x i m i t y o f t h e d i a g n o s -
tic socket D which is essential for
the maintenance of your vehicle.
Release the strap from its loca-
tion C .
Pull the strap to release the
b r a k e . A l o u d k n o c k c o n fi r m s t h e
release of the brake.
Take care to put the strap back in
its location C correctly. Otherwise,
it will no longer be possible to ap-
ply the brake. Consult a CITROËN
dealer.
Put the rubber mat back in place
on the base of the armrest.
Page 152 of 336
IX
!
131
D R I V I N G
If any of these instances arises, contact a CITROËN dealer as soon as possible.
SITUATION
CONSEQUENCES
1 Electric parking brake fault and display of
message "
Parking brake faulty " and the
following warning lamps: If the electric parking brake fault warning lamp and the servi
ce
w a r n i n g l a m p l i g h t u p , p o s i t i o n t h e v e h i c l e i n a s a f e l o c a t i o n ( o n fl a t
ground, with a gear engaged).
2 Display of the messages "
Parking brake
faulty " and " Anti roll-back
fault " and of the
following warning lamps: - The automatic functions are deactivated.
- The hill start assist is not available.
- The electric parking brake is only available manually.
3 Display of messages "
Parking brake faulty "
and " Anti roll-back
fault " and of the following
warning lamp: - Manual release of the electric parking brake is not availa ble.
- The hill start assist is not available.
- The automatic functions and manual application are still available.
Operating faults
Page 153 of 336
IX
132
D R I V I N G
SITUATION
CONSEQUENCES
4 Display of messages "
Parking brake faulty "
and " Anti roll-back
fault " and of the following
warning lamps:
and/or fl a s h i n g - The automatic functions are deactivated.
- The hill start assist is not available.
To apply the electric parking brake:
Immobilise the vehicle and switch off the ignition
P u l l t h e c o n t r o l l e v e r f o r a t l e a s t 5 s e c o n d s o r u n t i l m a x i m u m
application.
S w i t c h o n t h e i g n i t i o n a n d c h e c k t h a t t h e e l e c t r i c p a r k i n g b r a k e
warning lamps are on.
- Application may take longer than in normal operation.
- I f w a r n i n g l a m p ( ! ) fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer.
To release the electric parking brake:
S w i t c h o n t h e i g n i t i o n .
P u s h t h e c o n t r o l l e v e r a n d h o l d i t f o r a p p r o x i m a t e l y 3 s e c o n d s .
5 Display of message "
Parking brake control
faulty – automatic mode activated " and the
following warning lamps:
and/or fl a s h i n g - Only the functions for automatic application on switchi
ng off the
engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake a nd
dynamic emergency braking are unavailable.
6 Display of message "
Parking brake faulty "
and of the following warning lamp:
fl a s h i n g - Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
W a i t a p p r o x i m a t e l y 3 m i n u t e s .
A f t e r 3 m i n u t e s , i f t h e w a r n i n g l a m p i s s t i l l fl a s h i n g , t r y t o r e i n i -
tialise the parking brake, either by pushing and releasing th e
control A while pressing the brake pedal or by means of a long
pull on control A .
7 Battery fault - Lighting of the battery warning lamp ma
kes it essential to stop
t h e v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r
vehicle.
- Apply the electric parking brake before switching off the engine.
Page 154 of 336
IX!
133
D R I V I N G
HILL START ASSIST
S y s t e m w h i c h k e e p s y o u r v e h i c l e
i m m o b i l i s e d t e m p o r a r i l y ( a p p r o x i -
mately 2 seconds) when starting on
a gradient, the time to move your
foot from the brake pedal to the ac-
celerator pedal.
This function is only active when:
- the vehicle is completely station-ary, with your foot on the brake
pedal,
- in certain conditions on a gradient,
- with the driver’s door closed.
The hill start assist function cannot
be deactivated. Operation
On an ascending gradient, with
the vehicle stationary, the vehicle
is held for a brief moment when
you release the brake pedal:
- p r o v i d e d y o u a r e i n fi r s t g e a r o r n e u t r a l o n a m a n u a l g e a r b o x ,
- provided you are in D or M on an
a u t o m a t i c g e a r b o x .
On a descending gradient, with
the vehicle stationary and reverse
gear engaged, the vehicle is held
for a brief moment when you re-
lease the brake pedal.
D o n o t e x i t t h e v e h i c l e w h i l e
it is being held in the hill start
assist phase.
If you need to leave the vehicle with
the engine running, apply the park-
ing brake manually and ensure that
the parking brake warning lamp (in
t h e i n s t r u m e n t p a n e l ) i s o n fi x e d
( n o t fl a s h i n g ) .
Page 155 of 336
IX
134
D R I V I N G
5-SPEED MANUAL GEARBOX
Starting the vehicle
Check that the gear lever is in
neutral.
Do not touch the accelerator.
For Diesel engines: turn the
key to position M and wait until
the pre-heating warning lamp
switches off if it has come on.
Operate the starter, turning the
key until the engine starts (no
more than ten seconds).
In temperatures lower than 0 °C,
declutch while operating the
starter to facilitate starting. Engaging reverse gear
Push the gear lever to the right
then rearwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
6-SPEED MANUAL GEARBOX
Engaging reverse gear
Raise the ring under the knob
(indicated by the arrow) and
push the gear lever to the left
then forwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
As a safety precaution and to facili-
tate starting of the engine:
- always select neutral,
- press the clutch pedal.
Page 156 of 336
IX
!
135
D R I V I N G
GEAR SHIFT INDICATOR *
S y s t e m w h i c h r e d u c e s f u e l c o n -
sumption by advising the driver to
c h a n g e u p o n v e h i c l e s fi t t e d w i t h a
m a n u a l g e a r b o x .
Operation
The system intervenes only when
driving economically.
Depending on the driving situation
and your vehicle's equipment, the
system may advise you to skip one
or more gears. You can follow this
instruction without engaging the in-
termediate gears.
The gear engagement recommen-
dations must not be considered
c o m p u l s o r y . I n f a c t , t h e c o n fi g u -
ration of the road, the amount of
t r a f fi c a n d s a f e t y r e m a i n d e t e r m i n -
ing factors when choosing the best
gear. Therefore, the driver remains
responsible for deciding whether or
not to follow the advice given by the
system.
This function cannot be deactivated.
* According to engine. E x a m p l e :
- You are in third gear.
- You press the accelerator pedal
moderately.
- The system may suggest that you engage a higher gear, if ap-
propriate. The information appears in the in-
strument panel screen in the form of
an arrow accompanied by the sug-
gested gear.
In the case of driving which
makes particular demands on
the performance of the engine
( fi r m p r e s s u r e o n t h e a c c e l e r a t o r
p e d a l , f o r e x a m p l e , w h e n o v e r t a k -
ing...), the system will not recom-
mend a gear change.
The system never suggests:
- e n g a g i n g fi r s t g e a r ,
- engaging reverse gear,
- engaging a lower gear.
Page 157 of 336
IX
136
D R I V I N G
6-SPEED ELECTRONIC GEARBOX SYSTEM
automatic mode: gear lever in
position A ,
sequential mode: gear lever in
position M ,
SPORT mode: gear lever in po-
sition A and a press on button 1 .
S i x - s p e e d e l e c t r o n i c g e a r b o x s y s -
tem which offers a choice between
the comfort of fully automatic opera-
tion or the pleasure of manual gear
changing.
There are two driving modes:
-
automatic operation for elec-
tronic control of the gears by the
g e a r b o x ,
- manual operation for sequential
gear changing by the driver,
In automated mode, it remains pos-
sible to change gear manually by
using the steering mounted control
p a d d l e s , w h e n o v e r t a k i n g , f o r e x -
ample.
A SPORT programme is available in
automated mode, providing a more
dynamic driving style. Mode selection
The steering mounted paddles
cannot be used to select neutral
or to engage or disengage reverse
gear.
+. Change up paddle to the right of
the steering wheel.
Press the back of the "+" steer-
ing mounted paddle to change
up a gear.
-. Change down paddle to the left of
the steering wheel.
Press the back of the "-" steer-
ing mounted paddle to change
down a gear.
Steering mounted control paddles
Page 158 of 336
IX
137
D R I V I N G
The position of the gear lever the the
driving mode are displayed in dial C
of the instrument panel.
A selection grille alongside the gear
lever also allows you to see the
selected position.
Displays in the instrument panel Moving off
To start the engine, the gear lever
must be in position N .
Press the brake pedal down fully.
Operate the starter
N appears in the instrument panel
screen.
N fl a s h e s i n t h e i n s t r u m e n t p a n e l ,
accompanied by an audible signal
and a message on the multifunc-
tion screen, if the gear lever is not
in position N on starting.
S e l e c t fi r s t g e a r ( p o s i t i o n M or A )
or reverse (position R ).
Release the parking brake un-
less it is programmed in auto-
matic mode.
Release the brake pedal, then
accelerate.
With your foot on the brake, push
the lever forwards.
Reverse
Only engage reverse with
the vehicle immobilised.
To avoid any jerking, wait a
moment before accelerating.
Neutral Never select position N with
the vehicle moving.
Page 159 of 336
IX
138
D R I V I N G
Manual gear changing
This selective gear change mode
e n a b l e s y o u t o o v e r t a k e , f o r e x a m -
ple, while still remaining in automat-
ic mode.
Operate the + or - steering
mounted control paddle.
T h e g e a r b o x e n g a g e s t h e g e a r r e -
quested if the engine speed per-
mits.
After a few moments without any
a c t i o n o n t h e c o n t r o l s , t h e g e a r b o x
resumes automatic control of the
gears.
S e l e c t p o s i t i o n A .
T h e g e a r b o x c o n t i n u o u s l y s e l e c t s
the most suitable gear, depending
on the:
- style of driving,
- p r o fi l e o f t h e r o a d .
- vehicle loading.
Automatic operation
F o r o p t i m u m a c c e l e r a t i o n , f o r e x a m p l e
when overtaking another vehicle, press
t h e a c c e l e r a t o r p e d a l fi r m l y p a s t t h e
point of resistance.
S e l e c t p o s i t i o n M .
Manual operation
On sharp acceleration, the gear-
b o x w i l l n o t c h a n g e u p u n l e s s t h e
driver acts on the gear lever or the
steering mounted paddles.
Never select neutral
N while the
vehicle is moving.
Only engage reverse gear R when
the vehicle is immobilised with the
brake pedal pressed.
The gear change requests are only
carried out if the engine speed per-
mits.
It is not necessary to release the ac-
celerator during gear changes.
When braking or slowing down, the
g e a r b o x c h a n g e s d o w n a u t o m a t i -
cally to allow vehicle to accelerate in
the correct gear.
The
SPORT programme is inopera-
tive with sequential operation.
Page 160 of 336
IX
!
139
D R I V I N G
When immobilising the ve-
hicle, with the engine running,
you must place the gear lever
in neutral N .
Before carrying out any work in the
engine compartment, check that
the gear lever is in neutral N and
that the parking brake is applied.
SPORT programme Stopping the vehicle
Before switching off the engine, you
can choose to:
- move to position N to engage
neutral,
- leave the gear engaged; in this case, it will not be possible to
move the vehicle.
In both cases, you must apply the
parking brake to immobilise the ve-
hicle. Operating fault
W i t h t h e i g n i t i o n o n , t h e fl a s h i n g o f
AUTO , accompanied by an audible
signal and a message on the mul-
tifunction screen, indicates a mal-
f u n c t i o n o f t h e g e a r b o x .
Have it checked by a CITROËN
dealer.
Wit the gear lever at A and the
engine running, press button S to
activate the SPORT programme,
which provides a more dynamic
driving style.
S appears in the instrument panel.
Press the S button again to
switch it off.
S then disappears from the instru-
ment panel screen. You must press the brake pedal
when starting the engine.
Whatever the circumstances, you
must manually apply the parking
brake when parking, unless the
parking brake is programmed in au-
tomatic mode.