warning DACIA SOLENZA 2004 Owner's Manual

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 16
Procedures
17. The procedure is finished. Check the engine starting with both keys.
REMARK:
For the RF remote control synchronisation, after the replacement of a kit, take into account
the following situations:
- for the first RF remote control, perform the “ SIMPLE SYNCHRONISED PROCEDURE”;
- for t he second RF re m ote control pe rform the “SPE CIFIC SYNCHRONISE D
PROCEDURE”. C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by means of the CLIP tester. This is possible only
if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed by the
state:
10G ANTI STARTING ……………………………………………….ACTIVE
After getting from DACIA database the repairing code (based on the vehicle chassis series
and on the code from the vehicle’s key head), perform the following operations.
1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle.
2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “B41”;
5. Select the menu “ COMPUTER TEST” then select “ ANTI STARTING”.
6. In the menu “STAT E LIST” find the state 10G “ANTI STARTING” which must be
“ACTIVE”. 7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL CODE INTRODUCTION” where you will write the
repairi ng c ode (form ed of 4 fi gures), then validate it with t he ke y “ ENTER”. The message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”. 9. Now the procedure is finished and you may start the vehicle engine.
AT T E N T I ON!
Yo u may perform three attempts of introducing the repairing code; if after the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then set it
again, then other three attempts may be performed.
REMARK:
This procedure does not decode the injection computer, but is only allowing the start
of the vehicle’s engine. After 10 minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 17
Procedures
D. SIMPLE SYNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations: -the RF remote control c ode is no longer in the range of the E .C.U. decoder reception,
because of blind consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E .C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.);
The following operations will be performed: -take off the contact;
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course;
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/opening course;
-the procedure of synchronisation is finished; check the doors blocking/ unlocking by
pushing the RF remote control.
OBSERVAT ION:
During those 10 seconds you can visualise by means of the CLIP tester t he state 17G
“PROGRAMMING OR TIR/TRF RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E.C.U. decoder
and will be performed as follows:
-connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket)
of the vehicle;
- select the vehicle type “B41”;
- select the menu “ COMPUTERS TEST” then “ ANTI STARTING”;
- enter the menu “COMMAND MODE” and select “CONFIGURATION”;
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course. - during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice t he RF remote control button; the doors will block and then unlock and the
anti starting indicator will turn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 18
Diag nostic
FA ILURES AND STATES INTERPRETATION
1. FAILURE OF COMMUNICATION CLIP TESTER/ E.C.U. DECODER
RECOMMENDATION Check if the lines K and L are not disturbed by another computer of the vehicle.
Check the condition of fuse F 03 from the cockpit fuse box.
Replace the fuse if necessary.
Check if the CLIP tester is not the cause of the failure; check if the tester is communicating
with another computer of the same vehicle (injection computer).
M easure the tension of the vehicle’s battery (U> 12,3V). If necessary, charge the battery.
Check if the E.C.U. decoder is correctly connected to the vehicle’s wiring.
Check the right supply of the E.C.U. decoder:
-presence of the mass at pin A8 of the E .C.U. decoder
- supply + I.C. at pin A9 of t he E .C.U. decoder
Be sure that the diagnostic socket i s proper supplied, according to the circuit diagram.
Check the continuity and the isolation of the electric wiring on the corresponding pins layout.
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the connection tester CLIP – E.C.U. decoder can’t be established, then replace the decoder.
AFTER REPAIRING After establishing the communication with the tester, fix the
possible failures.
Perform a conformity checking.
{ }
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 19
Diag nostic
2. 4D STATE: + 12 V (+DC) SUPPLY, EXISTENT
RECOMMENDATION Observation : - 4D state = ACTIVE when the contact i s on “M” position;
- 4D state = PASSIVE when the contact is not on “M ”position.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
YES
NO Replace the E.C.U. decoder if its communication with t he tester can not be realised.
Repair the electric wiring on the supply layout to the pin A7 of E.C.U. decoder.
Check the F03 fuse condition.
Replace the fuse if necessary.
Place the contact on “M” position and check the presence of +12V at the pin A7 of the
E.C.U. decoder. Is there +12V?
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 20
Diag nostic
3. FAILURE : DOORS BLOCKING SWITCH
Remove the memorised failure by means of the CLIP tester.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
Check the isolation related to the m ass of the
wir ing between the E.C.U. decoder doors’
locking switch B2 pin pole 1
B5 pin pole 5
Is there a correct isolation?
Repair the electric wiring.No
Replace t he doors’ locking switch.
Ye s
RECOMMENDATION Check if the switch does not remain permanently pressed due to a
mechanical blocking.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 21
Diag nostic
4.FAILURE: M ISSING SIG NAL ON TH E CO DED LINE E.C.U. DECO DER-
COMPUTER INJECTION
RECOMMENDATION-
Check the continuity and the isolation related t o the mass and + 12 V of the wiring between
the E .C.U. decoder PinA6 pin58 injection computer.
Fix it if necessary.
.
Set t he contact on and perform the detection test using the CLIP tester at pin A 6 of the ECU
decoder.
Are there any impulses?
YES
NO Replace the ECU injection.
Replace the E .C.U. decoder.
Remove the memorised
failures by means of the CLIP tester.
AFTER REPAIRING Perform a conformity test. Check the operation of the anti starting system.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 22
Diag nostic
5. FAILURE : DEFECTIVE COMMUNICATION ANTI STARTING SYSTEM -
E.C.U. DECODER
RECOMMENDATION -
Check the continuity and the isolation related to the mass and + 12 V voltage of the wiring
between the anti starting system pin 4 pin A2 E.C.U. decoder
Fix it if necessary.
Check the anti starting bushing supply : + 12V to the pin 3 and the mass to pin 2.
Di sconnect the E.C.U. decoder and measure the presence of +12 V at the pin A2 of the
decoder, the contact being taken off. If there it isn’t +12 V, check the fuse condition F03 from
the cockpit fuse box.
If the problem persists, replace the anti starting bushing.
Set the contact on and perform the impulse detection test at the pin A2 of the E.C.U. decoder.
Is there an impulse ?
YES
NO Replace the anti starting bushing.
Replace t he E.C.U. decoder.
Remove the memorised
failures by means of the CLIP tester.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system .
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 23
Diag nostic
6. STATE 11G: ACTIVATE THE RF REMOTE CONTROL/ RECEIVED RF SIGNAL
IN DICATION
If the 17D state is PASSIVE, do not apply the next diagnostic
because the E .C.U. decoder is unused (new).
RECOMMENDATION Perform first the remote control synchronisation.
Do not access the next diagnostic if the state 11G remains
PA SSIVE when activating the RF remote c ontrol at the blocking
and unlocking of the doors.
Check the blocking and unlocking of the doors using the second RF remote control. If this
is one is operating, then the battery of the first RF remote control must be replaced.
Check the presence of +12 V(+DC) at the pin1 of the anti starting bushing.
Is there +12V ?
Pe rform using the CLIP tester, the impulse de tection test at the pin 1 of the anti
starting bushing, when using the RF remote control.
Are any impulses when using the remote control ?
YES Replace the E .C.U. decoder.
NO Replace the anti starting bushing.YES
Check the isolation related to the mass of the electric wiring between:
E.C.U. decoder Pin B1 pol e 1 anti start ing bushi ng Pin B2 pole 1 door locking switch
Pin B5 pole 5
Isolation against mass is good?
YES Fix the electric wiring.
NO Replace the E.C.U. decoder
.
NO
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 24
Diag nostic
7. 11D STATE: OPERATE THE RF REMOTE CONTROL / GOOD RF SIGNAL
INDICATION
Do not access the following diagnostic unless the state 11D
RECOMMENDATION becomes ACTIVE when operating the RF remote control.
Check if the keys belong to the vehicle in question.
There is a desynchronising between the code of the RF remote control and the E.C.U. decoder
if at the activation of the remote control, the 111D state remains PASSIVE a nd the state 11G
becomes ACTIVE for 3 seconds, then becomes PASSIVE. The blocking / unlocking of the
doors is not possible in this case.
Apply the corresponding procedure of resynchronisation (for one or 2 keys).
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 25
Diag nostic
8.14G STATE : DOORS BLOCKING/ UNLOCKING
RECOMMENDATION The state 10G (anti starting) must be ACTIVE .
Check the continuity and the isolation related to the +12 V and to the mass of the electric
wiring on the line E.C.U. decoder
Pin B2 pole 1 door locking switch.
Pin B5 pole 5
Fix the electric wiring if necessary or replace the switch.
If the incident persists, replace the E.C.U. decoder.
vnx.su