DODGE NEON 1997 1.G Wiring Diagrams Manual Online

Downloaded from www.Manualslib.com manuals search engine a change in current draw. The K2 circuit connects to
cavity 26 of the PCM connector.
The PCM provides ground for the engine coolant
temperature sensor signal (circuit K2) through circuit
K4. Circuit K4 connects to cavity 43 of the PCM con-
nector.
HELPFUL INFORMATION
The engine coolant temperature sensor is case
grounded. The case ground provides the ground for
the coolant temperature gauge circuit G20.
Circuit K4 splices to supply ground for the signals
from the following:
²Upstream heated oxygen sensor
²Downstream heated oxygen sensor
²Camshaft position sensor
²Crankshaft position sensor
²Battery temperature sensor
²Throttle position sensor
²Manifold absolute pressure sensor
²Knock sensor
²Intake air temperature sensor
²Vehicle speed sensor
THROTTLE POSITION SENSOR
From the Powertrain Control Module (PCM), cir-
cuit K6 supplies 5 volts to the Throttle Position Sen-
sor (TPS). Circuit K6 connects to cavity 61 of the
PCM connector.
Circuit K22 delivers the TPS signal to the PCM.
Circuit K22 connects to cavity 35 of the PCM connec-
tor.
The PCM provides ground for the TPS signal (cir-
cuit K22) through circuit K4. Circuit K4 connects to
cavity 43 of the PCM connector.
HELPFUL INFORMATION
Refer to Group 14 for TPS operation.
Circuit K6 splices to supply 5 volts to the Manifold
Absolute Pressure (MAP) sensor.
Circuit K4 splices to supply ground for the signals
from the following:
²Upstream heated oxygen sensor
²Downstream heated oxygen sensor
²Battery temperature sensor
²Camshaft position sensor
²Crankshaft position sensor
²Engine coolant temperature sensor
²Manifold absolute pressure sensor
²Knock sensor
²Intake air temperature sensor
²Vehicle speed sensor
MANIFOLD ABSOLUTE PRESSURE SENSOR
From the Powertrain Control Module (PCM), cir-
cuit K6 supplies 5 volts to the Manifold AbsolutePressure (MAP) sensor. Circuit K6 connects to cavity
61 of the PCM connector.
Circuit K1 delivers the MAP signal to the PCM. Cir-
cuit K1 connects to cavity 36 of the PCM connector.
The PCM provides ground for the MAP sensor sig-
nal (circuit K1) through circuit K4. Circuit K4 con-
nects to cavity 43 of the PCM connector.
HELPFUL INFORMATION
Refer to Group 14 for MAP sensor operation.
Circuit K6 splices to supply 5 volts to the Throttle
Position Sensor.
Circuit K4 splices to supply ground for the signals
from the following:
²Upstream heated oxygen sensor
²Downstream heated oxygen sensor
²Battery temperature sensor
²Camshaft position sensor
²Crankshaft position sensor
²Engine coolant temperature sensor
²Throttle position sensor
²Knock sensor
²Intake air temperature sensor
²Vehicle speed sensor
INTAKE AIR TEMPERATURE SENSOR
The intake air temperature sensor provides an
input to the Powertrain Control Module (PCM) on
circuit K21. Circuit K21 connects to cavity 37 of the
PCM connector.
From circuit K21 the intake air temperature sen-
sor draws voltage from the PCM. The sensor is a
variable resistor. As intake air temperature changes,
the resistance in the sensor changes causing a
change in current draw.
The PCM provides ground for the intake air temper-
ature sensor signal (circuit K21) through circuit K4. Cir-
cuit K4 connects to cavity 43 of the PCM connector.
HELPFUL INFORMATION
Circuit K4 splices to supply ground for the signals
from the following:
²Upstream heated oxygen sensor
²Downstream heated oxygen sensor
²Battery temperature sensor
²Camshaft position sensor
²Crankshaft position sensor
²Engine coolant temperature sensor
²Throttle position sensor
²Knock sensor
²Manifold absolute pressure sensor
²Vehicle speed sensor
KNOCK SENSOR
The knock sensor provides an input to the Power-
train Control Module (PCM) on circuit K42. Circuit
K42 connects to cavity 24 of the PCM connector.
PL8W - 30 FUEL/IGNITION SYSTEMS 8W - 30 - 17
DESCRIPTION AND OPERATION (Continued)

Downloaded from www.Manualslib.com manuals search engine The PCM provides ground for the knock sensor sig-
nal (circuit K42) through circuit K4. Circuit K4 con-
nects to cavity 43 of the PCM connector.
HELPFUL INFORMATION
Circuit K4 splices to supply ground for the signals
from the following:
²Upstream heated oxygen sensor
²Downstream heated oxygen sensor
²Battery temperature sensor
²Camshaft position sensor
²Crankshaft position sensor
²Engine coolant temperature sensor
²Throttle position sensor
²Intake air temperature sensor
²Manifold absolute pressure sensor
²Vehicle speed sensor
BATTERY TEMPERATURE SENSOR
From circuit G31 the battery temperature sensor
draws voltage from the Powertrain Control Module
(PCM). The sensor is a variable resistor. As battery
temperature changes, the resistance in the sensor
changes causing a change in current draw. Circuit
G31 connects to cavity 52 of the PCM connector.
The PCM provides ground for the battery tempera-
ture sensor signal (circuit G31) through circuit K4. Cir-
cuit K4 connects to cavity 43 of the PCM connector.
HELPFUL INFORMATION
Circuit K4 splices to supply ground for the signals
from the following:
²Upstream heated oxygen sensor
²Downstream heated oxygen sensor
²Camshaft position sensor
²Crankshaft position sensor
²Engine coolant temperature sensor
²Throttle position sensor
²Manifold absolute pressure sensor
²Knock sensor
²Intake air temperature sensor
²Vehicle speed sensor
FUEL INJECTORS
Circuit A14 is a bus bar in the Power Distribution
Center (PDC), and connects to battery voltage. The
contact side of the Automatic Shut Down (ASD) relay
connects circuit A14 and circuit A142. A 20 amp fuse
in the PDC protects circuits A14 and A142.
Circuit A14 also supplies voltage to the coil side of
the ASD relay. The Powertrain Control Module
(PCM) controls the ground circuit for the coil side of
the ASD relay on circuit K51. Circuit K51 connects to
cavity 67 of the PCM connector.
Circuit A142 supplies voltage for the fuel injectors.
The PCM controls the ground circuit of each injector.²Circuit K11 is the ground circuit for Injector #1.
Circuit K11 connects to cavity 13 of the PCM.
²Circuit K12 is the ground circuit for Injector #2.
Circuit K12 connects to cavity 17 of the PCM.
²Circuit K13 is the ground circuit for Injector #3.
Circuit K13 connects to cavity 7 of the PCM.
²Circuit K14 is the ground circuit for Injector #4.
Circuit K14 connects to cavity 16 of the PCM.
HELPFUL INFORMATION
Circuit A142 splices to supply voltage to the fuel
injectors, ignition coil, ASD relay, generator, and the
upstream and downstream heated oxygen sensors.
The PCM controls the ground circuit for each of the
components powered by circuit A142.
The injectors operate in sequence. Refer to Group
14 for system operation.
IGNITION COIL PACK
Circuit A14 is a bus bar in the Power Distribution
Center (PDC), and connects to battery voltage. The
contact side of the Automatic Shut Down (ASD) relay
connects circuit A14 and circuit A142. A 20 amp fuse
in the PDC protects circuits A14 and A142.
Circuit A14 also supplies voltage to the coil side of
the ASD relay. The Powertrain Control Module
(PCM) controls the ground path circuit for the coil
side of the ASD relay on circuit K51. Circuit K51 con-
nects to cavity 67 of the PCM connector.
Circuit A142 supplies voltage for the ignition coil
pack. The coil pack consists of two individual coils
molded together. The PCM controls the ground cir-
cuit of each coil.
²Circuit K19 is the ground circuit for the ignition
coil that fires spark plugs # 1 and # 4. Circuit K19
connects to cavity 2 of the PCM.
²Circuit K17 is the ground circuit for the ignition
coil that fires spark plugs #2 and # 3. Circuit K17
connects to cavity 3 of the PCM.
HELPFUL INFORMATION
Circuit A142 splices to supply voltage to the fuel
injectors, ignition coil, ASD relay, generator, upstream
heated oxygen sensor and downstream heated oxygen
sensor. The PCM controls the ground circuit for each of
the components powered by circuit A142.
IDLE AIR CONTROL MOTOR
The Powertrain Control Module (PCM) operates
the Idle Air Control (IAC) motor through 4 circuits -
K39, K40, K59, and K60. Each circuit connects to
separate cavities in the PCM connector.
²Circuit K39 connects to cavity 57 of the PCM
connector.
²Circuit K40 connects to cavity 48 of the PCM
connector.
8W - 30 - 18 8W - 30 FUEL/IGNITION SYSTEMSPL
DESCRIPTION AND OPERATION (Continued)

Downloaded from www.Manualslib.com manuals search engine ²Circuit K59 connects to cavity 58 of the PCM
connector.
²Circuit K60 connects to cavity 49 of the PCM
connector.
POWER STEERING PRESSURE SWITCH
The power steering pressure switch opens and
closes circuit K10 between the Powertrain Control
Module (PCM) and ground. Circuit K10 connects to
cavity 45 of the PCM connector.
Circuit Z12 provides ground for the power steering
pressure switch. The grounding point for circuit Z12
is the left side of the radiator closure panel.
TORQUE CONVERTER CLUTCH SOLENOID (TCC)
The Powertrain Control Module (PCM) operates
the TCC solenoid by providing a ground path on cir-
cuit K54. Circuit K54 connects to PCM cavity 79.
Circuit F12 supplies battery voltage to the TCC
solenoid. Circuit F12 connects to a bus bar in the
fuse block fed by circuit A21. A 15 amp fuse in the
fuse block, cavity 10, protects circuit F12. Circuit F12
connects to cavity 20 of the PCM connector.
HELPFUL INFORMATION
Circuit F12 splices to feed the ABS control module,
PCM, EGR solenoid, leak detection pump, and the
duty cycle EVAP/Purge solenoid. The F12 circuit also
connects to a bus bar in the PDC that supplies volt-
age to the coil side of radiator fan relay, A/C clutch
relay, and fuel pump relay.
In the RUN or START position, the ignition switch
connects circuit A1 from the fuse block and circuit
A21. Circuit A1 connects to battery voltage and is
protected by a 30 amp fuse in the PDC.
DUTY CYCLE EVAP/PURGE SOLENOID
Circuit F12 supplies battery voltage to the Duty
Cycle EVAP/Purge solenoid. The Powertrain Control
Module (PCM) switches ground path for the solenoid
ON and OFF through circuit K52.
Circuit F12 connects to a bus bar in the fuse block
fed by circuit A21. A 15 amp fuse in the fuse block,
cavity 10, protects circuit F12. Circuit F12 also con-
nects to cavity 20 of the PCM connector.
Circuit K52 connects to cavity 68 of the PCM, and
cavity 1 of the solenoid connector.
HELPFUL INFORMATION
Circuit F12 splices to feed the ABS control module,
PCM, EET solenoid, leak detection pump, and the
TCC solenoid. The F12 circuit also connects to a bus
bar in the PDC that supplies voltage to the coil side
of radiator fan relays, A/C clutch relay, and fuel
pump relay.
In the START or RUN position, the ignition switch
connects circuit A1 from the fuse block and circuitA21. Circuit A1 connects to battery voltage and is
protected by a 30 amp fuse in the PDC.
EGR TRANSDUCER (EET) SOLENOID
Circuit F12 supplies battery voltage to the EET
solenoid. The Powertrain Control Module (PCM)
switches ground path for the solenoid ON and OFF
through circuit K35.
Circuit F12 connects to a bus bar in the fuse block
fed by circuit A21. A 15 amp fuse in the fuse block,
cavity 10, protects circuit F12. Circuit F12 also con-
nects to cavity 20 of the PCM.
Circuit K35 connects to cavity 40 of the PCM con-
nector.
HELPFUL INFORMATION
Circuit F12 splices to feed the ABS control module,
PCM, Duty Cycle EVAP/Purge solenoid, leak detec-
tion pump, and the TCC solenoid. The F12 circuit
also connects to a bus bar in the PDC that supplies
voltage to the coil side of radiator fan relays, A/C
clutch relay, and fuel pump relay.
In the START or RUN position, the ignition switch
connects circuit A1 from the fuse block and circuit
A21. Circuit A1 connects to battery voltage and is
protected by a 30 amp fuse in the PDC.
LOW FUEL DETECT INPUT
Circuit G4 provides an input to the Powertrain Con-
trol Module (PCM) indicating fuel tank level. This cir-
cuit connects to cavity 23 of the PCM connector.
The G4 circuit is also used for the fuel gauge
located in the instrument cluster. For operation of
the fuel gauge, refer to section 8W-40.
PARK/NEUTRAL POSITION SWITCH INPUT (3±SPD
TRANSMISSION)
On vehicles equipped with the 3±spd automatic
transmission the park/neutral switch provides an
input to the Powertrain Control Module (PCM).
When CLOSED, the park/neutral position switch
provides a ground path on circuit T41 for the coil
side of the engine starter motor relay. The case
grounded switch provides ground for circuit T41.
Circuit A41 from the ignition switch provides bat-
tery voltage to the coil side of the relay.
Circuit T41 splices to cavity 76 of the PCM. The
park/neutral position switch provides an input to the
Powertrain Control Module (PCM).
HELPFUL INFORMATION
In the START position, the ignition switch connects
circuit A1 from the Power Distribution Center (PDC)
to circuit A41. A 30 amp fuse protects circuits A1 and
A41.
PL8W - 30 FUEL/IGNITION SYSTEMS 8W - 30 - 19
DESCRIPTION AND OPERATION (Continued)

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine 8W-35 ANTI-LOCK BRAKES
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATION.......................................................... 6
Component Page
ABS Hydraulic Modulator..............8W-35-4
ABS Pump Motor....................8W-35-3
ABS Pump Motor Relay.............8W-35-2, 3
ABS Relay Box....................8W-35-2, 3
ABS System Relay...................8W-35-2
ABS Warning Lamp..................8W-35-2
Controller Anti-Lock Brake.......8W-35-2, 3, 4, 5
Data Link Connector..................8W-35-3
Fuse 10 (FB)........................8W-35-2
Fuse 10 (PDC).......................8W-35-3
Fuse 25 (PDC).......................8W-35-4
Fuse Block.........................8W-35-2
G101..........................8W-35-2, 3, 4
G102..............................8W-35-4Component Page
Instrument Cluster...................8W-35-2
Left Front Wheel Speed Sensor..........8W-35-5
Left Rear Wheel Speed Sensor..........8W-35-5
Power Distribution Center...........8W-35-3, 4
Pump Motor Driver...................8W-35-3
Right Front Wheel Speed Sensor........8W-35-5
Right Rear Wheel Speed Sensor.........8W-35-5
S101..............................8W-35-4
S103..............................8W-35-3
S104..............................8W-35-4
S108..........................8W-35-2, 3, 4
S109..............................8W-35-2
S210..............................8W-35-3
Stop Lamp Switch....................8W-35-4
8W - 35 - 2 8W - 35 ANTI-LOCK BRAKESPL

Downloaded from www.Manualslib.com manuals search engine 10FUSE15A
10
30
1
10
ABS
RELAY
BOX
F12
18
DG/WT
1547
CONTROLLER
ANTI-LOCK
BRAKEABS
SYSTEM
RELAY
OUTPUT
G101
Z1
14
BK
Z1
14
BK
S108 BLOCK FUSE
ST-RUN A21
7
9
C22
CLUSTER
INSTRUMENT
G19
22
LG/OR
G19
20
LG/BR
1C103
ABS
SYSTEM
RELAY
CONTROL
G19
20
LG/BR
F12
20
DG/WT
6C101
S109
F12
20
DG/WT
B47
20
RD/LB
60
B57
20
BR/BK
ABS
SYSTEM
RELAY LAMP WARNING
ABSABS
PUMP
MOTOR
RELAY
4
57
CONTROLRELAY SYSTEMABSDRIVERLAMP WARNINGABS(8W-11-9)
(8W-15-2) (8W-15-2) (8W-11-2)
(8W-40-5)
(8W-11-9) (8W-10-12)
8W - 35 - 2 8W-35 ANTI-LOCK BRAKESPL-RHD
978W-1PLR03501

Downloaded from www.Manualslib.com manuals search engine 10FUSE40A
73
10
5 7
M
- +
- +
3610
POWER
DISTRIBUTION
CENTER BATT A0
DATA
LINK
CONNECTOR
D21
20
PK
ABS
RELAY
BOX
A20
12
RD/DG
5116 20
CONTROLLER
ANTI-LOCK
BRAKEABS
PUMP
MOTOR
RELAY
CONTROLSENSE MOTORPUMPABS SCI
TRANSMIT
G101
Z1
14
BK
Z1
14
BK
S108
D21
20
PKB116
20
GYB120
12
BR/WT
B120
16
BR/WT
S103
ABS
PUMP
MOTOR
S210
ABS
PUMP
MOTOR
RELAYDRIVER MOTOR
PUMP
(8W-10-7)(8W-10-4) (8W-10-4)
(8W-30-4)
(8W-15-2) (8W-15-2) (8W-11-11)
PL-RHD8W-35 ANTI-LOCK BRAKES 8W - 35 - 3
PLR03502978W-1

Downloaded from www.Manualslib.com manuals search engine LEFT
FRONT
DECAY
SOLENOID
CONTROL CONTROLSOLENOIDDECAYREARLEFT RIGHT
REAR
DECAY
SOLENOID
CONTROL CONTROL SOLENOIDDECAY FRONTRIGHT
LEFT
FRONT
DECAY
SOLENOID
CONTROL CONTROLSOLENOIDDECAYREARLEFT RIGHT
FRONT
DECAY
SOLENOID
CONTROL CONTROLSOLENOIDDECAYREAR RIGHT
65OUTPUTSWITCHLAMPSTOP
S108
5 GROUND
15A
FUSE
25
POWER
DISTRIBUTION
CENTER
25
26
F32
18
PK/DB
5 6
STOP
LAMP
SWITCH
L50
20
WT/TN
S101
L50
20
WT/TN
Z1
18
BKZ1
18
BK
Z1
14
BK
G101
Z12
18
BK/TN
Z12
18
BK/OR
13
B142
20
BR/YL
B146
20
BR/LBB143
20
DG/YLB148
20
DB/LB
42464348
G102 S104 MODULATOR HYDRAULIC
ABSBRAKE ANTI-LOCK
CONTROLLER
BATT A0
4 2 3 1
(8W-15-2)(8W-10-9)(8W-10-4)
(8W-30-12)
(8W-30-12)
(8W-15-2) (8W-15-3)(8W-15-3) (8W-10-4)
8W - 35 - 4 8W-35 ANTI-LOCK BRAKESPL-RHD
978W-1PLR03503

Downloaded from www.Manualslib.com manuals search engine SENSOR SPEED
WHEEL
FRONT
LEFT
LEFT
REAR
WHEEL
SPEED
SENSORRIGHT
FRONT
WHEEL
SPEED
SENSOR
RIGHT
REAR
WHEEL
SPEED
SENSOR
LEFT
FRONT
WHEEL
SPEED
SENSOR
(+)LEFT
FRONT
WHEEL
SPEED
SENSOR
(-) (+)SENSORSPEED WHEELREARLEFT
(-) SENSORSPEED WHEELREARLEFT RIGHT
FRONT
WHEEL
SPEED
SENSOR
(+)RIGHT
FRONT
WHEEL
SPEED
SENSOR
(-) (+)SENSORSPEED WHEELREAR RIGHT
(-) SENSORSPEED WHEELREAR RIGHT
89346712 B8
20
RD/DB
B9
20
RD
34C108
B6
20
WT/DBB7
20
WT
B1
20
WT/BKB2
20
DG/WT
12C108
B2
20
YLB1
20
YL/DBB3
20
LG/DBB4
20
LG
21
21
21
21
B3
20
LG/DBB4
20
LG
CONTROLLER
ANTI-LOCK
BRAKE
PAIR TWISTED
TWISTED
PAIR
TWISTED
PAIR
PAIR TWISTED
PL-RHD8W-35 ANTI-LOCK BRAKES 8W - 35 - 5
PLR03504978W-1

Downloaded from www.Manualslib.com manuals search engine 8W-35 ANTI-LOCK BRAKES
INDEX
page page
DESCRIPTION AND OPERATION
ABS PUMP MOTOR RELAY................ 6
ABS SYSTEM RELAY..................... 6
ABS WARNING LAMP..................... 6
ANTI-LOCK BRAKES..................... 6BRAKE SWITCH INPUT................... 7
DATA LINK CONNECTOR.................. 7
HELPFUL INFORMATION.................. 7
HYDRAULIC MODULATOR................. 6
WHEEL SPEED SENSORS................. 7
DESCRIPTION AND OPERATION
ANTI-LOCK BRAKES
Power for the Anti-Lock brake system is supplied
by two fuses. There is a 15 amp fuse located in the
fuse block cavity 10. This fuse supplies power to the
Controller Anti Lock Brake (CAB), and the ABS sys-
tem relay on the F12 circuit. The F12 circuit also
supplies power to the Powertrain Control Module
(PCM). Power for the fuse is supplied on the A21 cir-
cuit from the ignition switch. This fuse is HOT in the
START/RUN position.
The second fuse is located in the Power Distribu-
tion Center (PDC). It is a 40 amp fuse. This fuse is
HOT at all times and supplies power to the contact
side of the ABS pump motor relay.
There are three grounding points used in the ABS
system. One is a case ground on the CAB. The sec-
ond is the Z12 circuit at the CAB connector cavity 5.
This ground is spliced, and terminates at the left side
of the radiator closure panel.
The third ground is on the Z1 circuit. This ground
is used for the ABS hydraulic modulator, ABS system
relay, and the ABS pump motor. This ground, like the
Z12 ground splices and terminates at the left head-
lamp ground.
Additional information on the circuit function of
the ABS system is listed below. For diagnostic and
testing procedures, refer to the appropriate section of
the Service Manual or the Diagnostic Test Proce-
dures Manual.
ABS WARNING LAMP
The ABS warning lamp is an output from the Con-
troller Anti Lock Brake (CAB) and the ABS relay
box. It is used to alert the operator of a problem in
the ABS system. The G19 circuit from the CAB and
the ABS system relay is used to detect a problem. If
a problem is detected, the CAB grounds the G19 cir-
cuit and illuminates the lamp in the instrument clus-
ter.
Circuit G19 is also an output of the CAB to the
ABS system relay contact side.
ABS SYSTEM RELAY
The system relay is used for the operation of the
ABS system. Power for the relay is supplied on the
B57 circuit from cavity 57 of the Controller Anti Lock
Brake (CAB).
Ground for the relay is on the Z1 circuit. This
ground is spliced in with the pump motor and termi-
nates at the left headlamp ground.
When the system is operating normally power for
the contact side of the relay is supplied from the
CAB on the B57 circuit. It passes through the relay
to the Z1 ground and terminates at the left headlamp
ground. If a problem is detected in the system, the
contact side of the relay switches from the Z1 to the
F12 circuit. This causes the ABS warning lamp in
the instrument cluster to illuminate.
ABS PUMP MOTOR RELAY
The ABS pump motor relay controls when the
pump motor runs. Power for the coil side of the relay
is supplied from cavity 47 of the Controller Anti Lock
Brake (CAB) on the B47 circuit. This circuit also sup-
plies voltage for the contact side of the system relay.
The ground side of the coil is controlled by the B116
circuit. Circuit B116 connects to cavity 16 of the CAB
connector.
Circuit B120 from cavity 20 of the CAB connector
powers the ABS pump motor. This circuit is also used
as an input to the CAB for pump motor monitoring.
HYDRAULIC MODULATOR
The hydraulic modulator is used for the controlling
of the brake system pressure to the wheels. The mod-
ulator is made up of four solenoids.
Circuits involved are, B142 for the left front wheel,
B143 for the right front wheel, B146 for the left rear
wheel, and B148 for the right rear wheel.
The solenoids use a common ground on the Z1 cir-
cuit. There are two Z1 circuits from the modulator.
Both of these grounds terminate at the left headlamp
ground, and are spliced in with the ABS pump motor
and the ABS system relay.
8W - 35 - 6 8W - 35 ANTI-LOCK BRAKESPL