height DODGE RAM 2001 Service Manual PDF

should remain on the fence. Do not grind off or com-
pletely remove all old urethane from the fence, the
paint finish and bonding strength will be adversely
affected.
(1) Place replacement windshield into windshield
opening and position glass in the center of the open-
ing against the support spacers. Mark the outside
surface of the glass at the support spacers with a
grease pencil or pieces of masking tape and ink pen
to use as a reference for installation. Remove replace-
ment windshield from windshield opening (Fig. 9).
(2) Position the windshield inside up on a suitable
work surface with two padded, wood 10 cm by 10 cm
by 50 cm (4 in. by 4 in. by 20 in.) blocks, placed par-
allel 75 cm (2.5 ft.) apart (Fig. 10).
(3) Clean inside of windshield with MOPAR Glass
Cleaner and lint-free cloth.
(4) Apply clear glass primer 25 mm (1 in.) wide
around perimeter of windshield and wipe with a new
clean and dry lint- free cloth.
(5) Apply the molding to the windshield:
(a) Press the upper corners of the molding onto
the windshield.
(b) Press the header section onto the windshield.
(c) Press the A-Pillar sections onto the wind-
shield.
(6) Apply black-out primer onto the glass using the
windshield molding as a guide. The primer should be
15 mm (5/8 in.) wide on the top and sides of the glass
and 25 mm (1 in.) on the bottom of windshield. Allow
at least three minutes drying time.
(7) Locatenewsupport spacers on support brack-
ets and adjust to lowest height.
(8) Position one 5 mm (3/16 in.) soft spacer (p/n
55028214) at the bottom of the windshield fence (Fig.
11).(9) Apply a 13mm (1/2 in.) high and 10mm (3/8 in.)
wide bead of urethane around the perimeter of wind-
shield. At the bottom, apply the bead 7 mm (1/4 in.)
inboard from the glass edge. On the three sides
where the molding is on the glass, follow the edge of
molding. The urethane bead should be shaped in a
triangular cross-section, this can be achieved by
notching the tip of the applicator (Fig. 12).
(10) With the aid of a helper, position the wind-
shield over the windshield opening. Align the refer-
ence marks at the bottom of the windshield to the
support spacers.
Fig. 8 Cut Urethane Around Windshield
1 - WINDSHIELD
2 - COLD KNIFE
Fig. 9 Center Windshield and Mark at Support
1 - WINDSHIELD
2 - INDEX MARKS
3 - SUPPORT SPACERS
Fig. 10 Work Surface Set up
1 - WINDSHIELD AND MOULDINGS
2 - URETHANE BEAD AROUND GLASS 7mm (.3 in.) FROM
EDGE
3 - BLOCKS
BR/BESTATIONARY GLASS 23 - 149
WINDSHIELD (Continued)

(4) Check that safety labels regarding the use of
seat belts and air bags are in place (such as on the
sun visors) (Fig. 30).
(5) Ensure head restraints are properly installed.
Inspect the height adjustment for ease of operation.
INSPECTION - SEATS
(1) Remove protective seat, carpet and door covers
(if being delivered) where applicable.
(2) Check that manual/power seat adjustments
work properly for all seats (Fig. 31).²Inspect the operation of front seat mechanical
slides and power adjusters (Fig. 31)
²Check the seatback recliner for ease of release
and operation
²Check the rear seatback latches for ease of
release
²On fold-down rear seats, latch the rear seats
and pull forward on the seats to check that the
latches hold
(3) Check the seat heaters on vehicles equipped
with heated seats.
(4) Check that all seats are securely located in
their adjustable tracks (Fig. 31).
Fig. 31 SEAT CONTROLS
Fig. 28 HEADLAMP SWITCH
Fig. 29 EMERGENCY FLASHER SWITCH
Fig. 30 SEAT BELT LABELS
BR/BENEW VEHICLE PREPARATION 30 - 13
BODY INTERIOR (Continued)

ABS INDICATOR - DESCRIPTION.........8J-14
ABS INDICATOR - OPERATION..........8J-14
A/C APPLICATION TABLE,
SPECIFICATIONS......................24-8
A/C COMPRESSOR - DESCRIPTION......24-46
A/C COMPRESSOR - DIAGNOSIS AND
TESTING...........................24-46
A/C COMPRESSOR - INSTALLATION......24-47
A/C COMPRESSOR - OPERATION........24-46
A/C COMPRESSOR - REMOVAL.........24-47
A/C COMPRESSOR CLUTCH -
DESCRIPTION.......................24-13
A/C COMPRESSOR CLUTCH -
INSPECTION........................24-16
A/C COMPRESSOR CLUTCH -
INSTALLATION.......................24-16
A/C COMPRESSOR CLUTCH -
OPERATION.........................24-13
A/C COMPRESSOR CLUTCH - REMOVAL . . 24-14
A/C COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE...............24-13
A/C COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-13
A/C COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-17
A/C COMPRESSOR CLUTCH RELAY -
DIAGNOSIS AND TESTING.............24-17
A/C COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-18
A/C COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-17
A/C COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-18
A/C CONDENSER - DESCRIPTION........24-48
A/C CONDENSER - INSTALLATION.......24-49
A/C CONDENSER - OPERATION..........24-48
A/C CONDENSER - REMOVAL...........24-49
A/C EVAPORATOR - DESCRIPTION.......24-52
A/C EVAPORATOR - INSTALLATION......24-53
A/C EVAPORATOR - OPERATION.........24-53
A/C EVAPORATOR - REMOVAL..........24-53
A/C HEATER CONTROL - DESCRIPTION . . . 24-18
A/C HEATER CONTROL - DIAGNOSIS
AND TESTING.......................24-19
A/C HEATER CONTROL - INSTALLATION . . . 24-20
A/C HEATER CONTROL - OPERATION.....24-18
A/C HEATER CONTROL - REMOVAL......24-19
A/C HIGH PRESSURE SWITCH -
DESCRIPTION.......................24-20
A/C HIGH PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-20
A/C HIGH PRESSURE SWITCH -
INSTALLATION.......................24-21
A/C HIGH PRESSURE SWITCH -
OPERATION.........................24-20
A/C HIGH PRESSURE SWITCH -
REMOVAL..........................24-21
A/C LINE COUPLERS - DESCRIPTION.....24-40
A/C LINE COUPLERS - OPERATION......24-41
A/C LINE COUPLERS - STANDARD
PROCEDURE........................24-43
A/C LOW PRESSURE SWITCH -
DESCRIPTION.......................24-21
A/C LOW PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-21
A/C LOW PRESSURE SWITCH -
INSTALLATION.......................24-22
A/C LOW PRESSURE SWITCH -
OPERATION.........................24-21
A/C LOW PRESSURE SWITCH -
REMOVAL..........................24-21
A/C ORIFICE TUBE - DESCRIPTION.......24-53
A/C ORIFICE TUBE - OPERATION........24-53
A/C ORIFICE TUBE - REMOVAL..........24-54
A/C PERFORMANCE - DIAGNOSIS AND
TESTING............................24-2
ACCELERATOR PEDAL - INSTALLATION . . . 14-37
ACCELERATOR PEDAL - REMOVAL.......14-37
ACCELERATOR PEDAL POSITION
SENSOR - DESCRIPTION
...............14-91
ACCELERATOR PEDAL POSITION
SENSOR - INSTALLATION
..............14-93
ACCELERATOR PEDAL POSITION
SENSOR - OPERATION
................14-91
ACCELERATOR PEDAL POSITION
SENSOR - REMOVAL
..................14-91
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING
................7-24,7-27,7-31ACCUMULATOR - DESCRIPTION.........24-54
ACCUMULATOR - DESCRIPTION . 21-191,21-362,
21-537,21-707
ACCUMULATOR - INSPECTION . . 21-192,21-363,
21-538,21-708
ACCUMULATOR - INSTALLATION........24-55
ACCUMULATOR - OPERATION..........24-54
ACCUMULATOR - OPERATION . . . 21-191,21-362,
21-537,21-708
ACCUMULATOR - REMOVAL............24-54
ACTUATION TEST MODE - DESCRIPTION,
CIRCUIT.............................25-1
ACTUATOR - INSTALLATION, BLEND
DOOR.............................24-26
ACTUATOR - INSTALLATION, HEAT/
DEFROST DOOR.....................24-27
ACTUATOR - INSTALLATION, INSIDE
HANDLE.......................23-71,23-80
ACTUATOR - INSTALLATION, PANEL/
DEFROST DOOR.....................24-27
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-28
ACTUATOR - REMOVAL, BLEND DOOR....24-25
ACTUATOR - REMOVAL, HEAT/DEFROST
DOOR.............................24-26
ACTUATOR - REMOVAL, INSIDE HANDLE . 23-71,
23-80
ACTUATOR - REMOVAL, PANEL/DEFROST
DOOR.............................24-27
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-27
ADAPTER - INSTALLATION, DEFROSTER
AND DEMISTER DUCT.................24-35
ADAPTER - REMOVAL, DEFROSTER AND
DEMISTER DUCT.....................24-35
ADAPTER BRACKET - INSTALLATION,
CAB CHASSIS........................13-9
ADAPTER BRACKET - REMOVAL, CAB
CHASSIS............................13-9
ADAPTER HOUSING SEAL -
INSTALLATION.................21-132,21-87
ADAPTER HOUSING SEAL - REMOVAL . . 21-132,
21-87
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE................7-16
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING..................7-16
ADHESIVE LOCATIONS, SPECIFICATIONS
- STRUCTURAL......................23-44
ADJUSTER - DIAGNOSIS & TESTING,
POWER LUMBAR....................8N-18
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-29
ADJUSTER - INSTALLATION, SEAT
TRACK............................23-143
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-29
ADJUSTER - REMOVAL, SEAT TRACK....23-143
ADJUSTER ASSEMBLY - INSTALLATION,
ROCKER ARM........................9-85
ADJUSTER ASSEMBLY - REMOVAL,
ROCKER ARM........................9-85
ADJUSTER ASSY - CLEANING, ROCKER
ARM ..............................9-262
ADJUSTER ASSY - DESCRIPTION,
ROCKER ARM.......................9-261
ADJUSTER ASSY - INSPECTION,
ROCKER ARM.......................9-262
ADJUSTER ASSY - INSTALLATION,
ROCKER ARM.............9-142,9-200,9-263
ADJUSTER ASSY - REMOVAL, ROCKER
ARM ....................9-142,9-200,9-261
ADJUSTER KNOB - INSTALLATION,
TURNING LOOP HEIGHT...............8O-30
ADJUSTER KNOB - REMOVAL, TURNING
LOOP HEIGHT.......................8O-30
ADJUSTMENT - STANDARD
PROCEDURE, COMPASS VARIATION......8M-4
ADJUSTMENT AND VERIFICATION -
STANDARD PROCEDURE, VALVE LASH....9-256
ADJUSTMENT, BANDS . . . 21-193,21-364,21-539,
21-709
ADJUSTMENT, CABLE TENSIONER
........5-40
ADJUSTMENT, CARGO DOOR
...........23-78
ADJUSTMENT, CENTER BEARING -
CENTER BEARING
.....................3-10
ADJUSTMENT, FRONT DOOR FORE/AFT
. . . 23-68
ADJUSTMENT, FRONT DOOR IN/OUT
.....23-69ADJUSTMENT, FRONT DOOR LATCH......23-72
ADJUSTMENT, FRONT DOOR UP/DOWN . . . 23-69
ADJUSTMENT, FRONT FASCIA...........13-2
ADJUSTMENT, HOOD................23-100
ADJUSTMENT, LATCH................23-100
ADJUSTMENT, LATCH STRIKER........23-102
ADJUSTMENT, REAR BRAKE DRUM.......5-34
ADJUSTMENT, SHIFT LEVER....21-853,21-888,
21-925
ADJUSTMENT, SHIFT MECHANISM.....21-252,
21-423,21-596,21-769
ADJUSTMENTS, FOG LAMP UNIT........8L-12
ADJUSTMENTS, FRONT AXLE - 216FBI....3-17
ADJUSTMENTS, FRONT AXLE - 248FBI....3-50
ADJUSTMENTS, GEAR.................19-16
ADJUSTMENTS, HEADLAMP UNIT.......8L-21
ADJUSTMENTS, REAR AXLE - 248RBI....3-114
ADJUSTMENTS, REAR AXLE - 267RBI....3-145
ADJUSTMENTS, REAR AXLE - 286RBI....3-174
ADJUSTMENTS, REAR AXLE - 9 1/4 .......3-84
ADJUSTMENTS, TRANSMISSION
THROTTLE VALVE CABLE . 21-254,21-425,21-598,
21-771
ADJUSTMENTS, VALVE BODY . . . 21-304,21-476,
21-646,21-818
AFTER AN AIRBAG DEPLOYMENT -
STANDARD PROCEDURE, SERVICE.......8O-4
AIR BLEED - STANDARD PROCEDURE....14-57
AIR CHECKING TRANSMISSION CLUTCH
AND BAND OPERATION - DIAGNOSIS
AND TESTING................21-147,21-318
AIR CLEANER ELEMENT - INSTALLATION . . 9-245
AIR CLEANER ELEMENT - REMOVAL.....9-244
AIR CONDITIONER - DESCRIPTION,
HEATER .............................24-1
AIR CONDITIONER - OPERATION,
HEATER .............................24-1
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE WITH.......7-77
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE
WITHOUT............................7-78
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITH.............7-74
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITHOUT..........7-77
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-41
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-41
AIR COOLER AND PLUMBING -
CLEANING, CHARGE..................11-18
AIR COOLER AND PLUMBING -
DESCRIPTION, CHARGE...............11-17
AIR COOLER AND PLUMBING -
INSPECTION, CHARGE.................11-18
AIR COOLER AND PLUMBING -
INSTALLATION, CHARGE...............11-18
AIR COOLER AND PLUMBING -
OPERATION, CHARGE.................11-17
AIR COOLER AND PLUMBING -
REMOVAL, CHARGE..................11-17
AIR DAM - INSTALLATION, FRONT........13-2
AIR DAM - REMOVAL, FRONT...........13-1
AIR EXHAUSTER - INSTALLATION.......23-77
AIR EXHAUSTER - REMOVAL...........23-77
AIR HEATER - DESCRIPTION, INTAKE....14-100
AIR HEATER - INSTALLATION, INTAKE . . . 14-101
AIR HEATER - OPERATION, INTAKE.....14-100
AIR HEATER - REMOVAL, INTAKE.......14-100
AIR HEATER RELAY - DESCRIPTION,
INTAKE............................14-101
AIR HEATER RELAY - INSTALLATION,
INTAKE............................14-102
AIR HEATER RELAY - OPERATION,
INTAKE............................14-102
AIR HEATER RELAY - REMOVAL, INTAKE . 14-102
AIR IN FUEL SYSTEM - DIAGNOSIS AND
TESTING...........................14-56
AIR INJECTION PUMP - DESCRIPTION....25-28
AIR INJECTION PUMP - DIAGNOSIS AND
TESTING...........................25-28
AIR INJECTION PUMP - INSTALLATION . . . 25-29
AIR INJECTION PUMP - OPERATION
.....25-28
AIR INJECTION PUMP - REMOVAL
.......25-29
AIR INJECTION SYSTEM - DESCRIPTION
. . 25-25
AIR INJECTION SYSTEM - OPERATION
....25-27
AIR INJECTION SYSTEM - TORQUE
......25-28
BR/BEINDEX 1
Description Group-Page Description Group-Page Description Group-Page

HEAD - INSPECTION, CYLINDER . . . 9-137,9-193,
9-23,9-250,9-80
HEAD - INSTALLATION, CYLINDER . 9-137,9-193,
9-23,9-250,9-80
HEAD - OPERATION, CYLINDER . 9-136,9-22,9-79
HEAD - REMOVAL, CYLINDER . 9-137,9-192,9-23,
9-246,9-80
HEAD COVER GASKET - DESCRIPTION,
CYLINDER...........................9-22
HEAD COVER GASKET - OPERATION,
CYLINDER...........................9-22
HEAD COVER(S) - CLEANING, CYLINDER . 9-138,
9-194,9-24,9-253,9-81
HEAD COVER(S) - DESCRIPTION,
CYLINDER..........................9-194
HEAD COVER(S) - INSPECTION,
CYLINDER........9-138,9-194,9-24,9-253,9-81
HEAD COVER(S) - INSTALLATION,
CYLINDER........9-138,9-194,9-24,9-253,9-81
HEAD COVER(S) - REMOVAL, CYLINDER . 9-138,
9-194,9-24,9-253,9-81
HEAD GASKET FAILURE - DIAGNOSIS
AND TESTING, CYLINDER . 9-136,9-191,9-22,9-79
HEAD RESTRAINTS - INSPECTION, SEAT
BELTS, SHOULDER BELTS,
RETRACTORS.......................30-12
HEADLAMP - DESCRIPTION............8L-13
HEADLAMP - DIAGNOSIS AND TESTING . . 8L-13
HEADLAMP - INSTALLATION............8L-16
HEADLAMP - OPERATION..............8L-13
HEADLAMP - REMOVAL...............8L-16
HEADLAMP ALIGNMENT, SPECIAL
TOOLS..............................8L-4
HEADLAMP RELAY - DESCRIPTION......8L-16
HEADLAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-17
HEADLAMP RELAY - INSTALLATION......8L-18
HEADLAMP RELAY - OPERATION........8L-17
HEADLAMP RELAY - REMOVAL.........8L-18
HEADLAMP SWITCH - DESCRIPTION.....8L-18
HEADLAMP SWITCH - DIAGNOSIS AND
TESTING...........................8L-18
HEADLAMP SWITCH - INSTALLATION....8L-20
HEADLAMP SWITCH - OPERATION.......8L-18
HEADLAMP SWITCH - REMOVAL........8L-19
HEADLAMP UNIT - ADJUSTMENTS......8L-21
HEADLAMP UNIT - INSTALLATION.......8L-20
HEADLAMP UNIT - REMOVAL...........8L-20
HEADLINER - INSTALLATION..........23-125
HEADLINER - REMOVAL..............23-125
HEAT SHIELDS - DESCRIPTION.........11-10
HEAT SHIELDS - INSTALLATION.........11-10
HEAT SHIELDS - REMOVAL.............11-10
HEAT/DEFROST DOOR - INSTALLATION . . . 24-39
HEAT/DEFROST DOOR - REMOVAL.......24-38
HEAT/DEFROST DOOR ACTUATOR -
INSTALLATION.......................24-27
HEAT/DEFROST DOOR ACTUATOR -
REMOVAL..........................24-26
HEATED MIRROR GRID - DESCRIPTION . . . 8G-4
HEATED MIRROR GRID - DIAGNOSIS
AND TESTING........................8G-4
HEATED MIRROR GRID - OPERATION.....8G-4
HEATED MIRROR SWITCH - DIAGNOSIS
AND TESTING........................8G-3
HEATED MIRROR SYSTEM -
DESCRIPTION........................8G-1
HEATED MIRROR SYSTEM - DIAGNOSIS
AND TESTING........................8G-2
HEATED MIRROR SYSTEM - OPERATION . . . 8G-2
HEATED SEAT ELEMENT - DESCRIPTION . . 8G-10
HEATED SEAT ELEMENT - OPERATION....8G-10
HEATED SEAT ELEMENT AND SENSOR -
DIAGNOSIS & TESTING...............8G-11
HEATED SEAT RELAY - DESCRIPTION....8G-11
HEATED SEAT RELAY - DIAGNOSIS &
TESTING...........................8G-12
HEATED SEAT RELAY - INSTALLATION....8G-13
HEATED SEAT RELAY - OPERATION......8G-12
HEATED SEAT RELAY - REMOVAL.......8G-13
HEATED SEAT SWITCH - DIAGNOSIS &
TESTING
.......................8G-14,8G-8
HEATED SEAT SYSTEM - DESCRIPTION
....8G-5
HEATED SEAT SYSTEM - DIAGNOSIS &
TESTING
............................8G-6
HEATED SEAT SYSTEM - OPERATION
.....8G-6
HEATER - 3.9L/5.2L/5.9L -
DESCRIPTION, ENGINE BLOCK
...........7-45HEATER - 3.9L/5.2L/5.9L -
INSTALLATION, ENGINE BLOCK..........7-45
HEATER - 3.9L/5.2L/5.9L - OPERATION,
ENGINE BLOCK.......................7-45
HEATER - 3.9L/5.2L/5.9L - REMOVAL,
ENGINE BLOCK.......................7-45
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-47
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-47
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-47
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.......................7-47
HEATER - 8.0L - DESCRIPTION, ENGINE
BLOCK..............................7-46
HEATER - 8.0L - INSTALLATION, ENGINE
BLOCK..............................7-46
HEATER - 8.0L - OPERATION, ENGINE
BLOCK..............................7-46
HEATER - 8.0L - REMOVAL, ENGINE
BLOCK..............................7-46
HEATER - DESCRIPTION, FUEL..........14-62
HEATER - DESCRIPTION, INTAKE AIR....14-100
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-62
HEATER - INSTALLATION, INTAKE AIR . . . 14-101
HEATER - OPERATION, FUEL............14-62
HEATER - OPERATION, INTAKE AIR.....14-100
HEATER - REMOVAL, INTAKE AIR.......14-100
HEATER - REMOVAL/INSTALLATION,
FUEL................................14-63
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DESCRIPTION, A/C . . . 24-18
HEATER CONTROL - DIAGNOSIS AND
TESTING, A/C.......................24-19
HEATER CONTROL - INSTALLATION, A/C . . 24-20
HEATER CONTROL - OPERATION, A/C....24-18
HEATER CONTROL - REMOVAL, A/C......24-19
HEATER CORE - DESCRIPTION..........24-55
HEATER CORE - INSTALLATION.........24-56
HEATER CORE - OPERATION............24-55
HEATER CORE - REMOVAL.............24-56
HEATER CORE GROUND STRAP -
INSTALLATION.......................8A-15
HEATER CORE GROUND STRAP -
REMOVAL..........................8A-14
HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-6
HEATER RELAY - DESCRIPTION, FUEL....14-63
HEATER RELAY - DESCRIPTION, INTAKE
AIR ..............................14-101
HEATER RELAY - DIAGNOSIS AND
TESTING, FUEL......................14-64
HEATER RELAY - INSTALLATION, FUEL . . . 14-65
HEATER RELAY - INSTALLATION, INTAKE
AIR ..............................14-102
HEATER RELAY - OPERATION, FUEL......14-63
HEATER RELAY - OPERATION, INTAKE
AIR
..............................14-102
HEATER RELAY - REMOVAL, FUEL
.......14-65
HEATER RELAY - REMOVAL, INTAKE AIR
. 14-102
HEATER SWITCH - DESCRIPTION,
DRIVER SEAT
........................8G-7
HEATER SWITCH - DESCRIPTION,
PASSENGER SEAT
....................8G-13
HEATER SWITCH - INSTALLATION,
DRIVER SEAT
........................8G-9
HEATER SWITCH - INSTALLATION,
PASSENGER SEAT
....................8G-16
HEATER SWITCH - OPERATION, DRIVER
SEAT
...............................8G-7
HEATER SWITCH - OPERATION,
PASSENGER SEAT
....................8G-14
HEATER SWITCH - REMOVAL, DRIVER
SEAT
...............................8G-9
HEATER SWITCH - REMOVAL,
PASSENGER SEAT
....................8G-15
HEATER/AIR CONDITIONER -
INSPECTION
........................30-17
HEAVY DUTY ENGINE (FEDERAL ONLY -
2500 8.0L HD AND 3500 5.9L& 8.0L
MODELS) MAINTENANCE SCHEDULES
- DESCRIPTION
.......................0-17HEAVY DUTY/8.0L - DESCRIPTION,
CATALYTIC CONVERTER - 5.9L...........11-6
HEAVY DUTY/8.0L - INSPECTION,
CATALYTIC CONVERTER - 5.9L...........11-7
HEAVY DUTY/8.0L - INSPECTION,
EXHAUST PIPE - 5.9L..................11-9
HEAVY DUTY/8.0L - INSPECTION,
TAILPIPE - 5.9L......................11-12
HEAVY DUTY/8.0L - INSTALLATION,
CATALYTIC CONVERTER - 5.9L...........11-7
HEAVY DUTY/8.0L - INSTALLATION,
EXHAUST PIPE - 5.9L..................11-9
HEAVY DUTY/8.0L - INSTALLATION,
TAILPIPE - 5.9L......................11-12
HEAVY DUTY/8.0L - OPERATION,
CATALYTIC CONVERTER - 5.9L...........11-6
HEAVY DUTY/8.0L - REMOVAL,
CATALYTIC CONVERTER - 5.9L...........11-6
HEAVY DUTY/8.0L - REMOVAL,
EXHAUST PIPE - 5.9L..................11-8
HEAVY DUTY/8.0L - REMOVAL, TAILPIPE
- 5.9L..............................11-12
HEIGHT ADJUSTER KNOB -
INSTALLATION, TURNING LOOP.........8O-30
HEIGHT ADJUSTER KNOB - REMOVAL,
TURNING LOOP.....................8O-30
HIGH BEAM INDICATOR - DESCRIPTION . . 8J-21
HIGH BEAM INDICATOR - DIAGNOSIS
AND TESTING.......................8J-22
HIGH BEAM INDICATOR - OPERATION....8J-22
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER....................8L-6
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER....................8L-6
HIGH PRESSURE FUEL LINES -
DESCRIPTION.......................14-74
HIGH PRESSURE FUEL LINES -
OPERATION.........................14-74
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-46
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-46
HIGH PRESSURE SWITCH -
DESCRIPTION, A/C...................24-20
HIGH PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-20
HIGH PRESSURE SWITCH -
INSTALLATION, A/C...................24-21
HIGH PRESSURE SWITCH - OPERATION,
A/C................................24-20
HIGH PRESSURE SWITCH - REMOVAL,
A/C................................24-21
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-74
HINGE - INSTALLATION......23-71,23-79,23-99
HINGE - REMOVAL.........23-70,23-79,23-99
HITCH - INSTALLATION, TRAILER........13-10
HITCH - REMOVAL, TRAILER...........13-10
HOISTING - STANDARD PROCEDURE......0-28
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-18
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-18
HOLDDOWN - OPERATION, BATTERY.....8F-18
HOLDDOWN - REMOVAL, BATTERY......8F-18
HOLDER - INSTALLATION, CUP........23-111
HOLDER - REMOVAL, CUP............23-110
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-6
HONING - STANDARD PROCEDURE,
CYLINDER BORE........9-10,9-126,9-180,9-69
HOOD - ADJUSTMENT
...............23-100
HOOD - INSTALLATION
...............23-100
HOOD - REMOVAL
...................23-100
HOOD LATCH/SAFETY CATCH -
INSPECTION
.........................30-4
HOOK - INSTALLATION, COAT
..........23-125
HOOK - INSTALLATION, FRONT TOW
.....13-10
HOOK - REMOVAL, COAT
.............23-124
HOOK - REMOVAL, FRONT TOW
..........13-9
HORN - DESCRIPTION
.............8H-1,8H-2
HORN - DIAGNOSIS AND TESTING
.......8H-2
HORN - INSPECTION
..................30-19
HORN - OPERATION
...............8H-1,8H-2
HORN RELAY - DESCRIPTION
...........8H-3
BR/BEINDEX 17
Description Group-Page Description Group-Page Description Group-Page

INTAKE/EXHAUST VALVES & SEATS -
VALVE SERVICE......................9-195
IN-TANK TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLER AND TUBES - WITHOUT
RADIATOR...................7-80,7-83,7-86
IN-TANK TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITH
RADIATOR...................7-79,7-83,7-85
INTERIOR - CAUTION................23-118
INTERLOCK SYSTEM - INSPECTION,
SHIFT/CLUTCH.......................30-19
INTERMEDIATE - INSTALLATION, AXLE
SHAFTS.............................3-28
INTERMEDIATE - REMOVAL, AXLE
SHAFTS.............................3-28
INTERMEDIATE AXLE - INSTALLATION.....3-61
INTERMEDIATE AXLE - REMOVAL.........3-60
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-6
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-3
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS . . 9-118,9-173,9-3
INTRODUCTION - DIAGNOSIS AND
TESTING-ENGINE DIAGNOSIS............9-61
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
IOD FUSE - DESCRIPTION...........8W-97-4
IOD FUSE - INSTALLATION...........8W-97-5
IOD FUSE - OPERATION.............8W-97-5
IOD FUSE - REMOVAL................8W-97-5
ISO FLARING - STANDARD PROCEDURE....5-8
ITEMS - INSTALLATION, SHIPPED LOOSE . 30-14
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - DIAGNOSIS AND TESTING,
UPPER BALL.........................2-12
JOINT - INSTALLATION, LOWER BALL.....2-25
JOINT - INSTALLATION, UPPER BALL.....2-25
JOINT MOLDING - INSTALLATION, ROOF . . 23-91
JOINT MOLDING - REMOVAL, ROOF......23-91
JOINTS - DISASSEMBLY, SINGLE
CARDAN UNIVERSAL..................3-11
JOINTS - INSTALLATION, SINGLE
CARDAN UNIVERSAL..............3-34,3-66
JOINTS - REMOVAL, SINGLE CARDAN
UNIVERSAL......................3-33,3-65
JOUNCE BUMPER - DESCRIPTION.....2-28,2-9
JOUNCE BUMPER - OPERATION.......2-28,2-9
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD
BEARING AND CRANKSHAFT...........9-274
JUMP STARTING - STANDARD
PROCEDURE.........................0-27
JUNCTION BLOCK - DESCRIPTION.....8W-97-6
JUNCTION BLOCK - INSTALLATION....8W-97-7
JUNCTION BLOCK - OPERATION......8W-97-6
JUNCTION BLOCK - REMOVAL........8W-97-6
KEEPER - INSTALLATION, BACKLITE
LATCH ............................23-146
KEEPER - REMOVAL, BACKLITE LATCH . . 23-146
KEY LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH............19-10
KEY-IN IGNITION SWITCH -
DESCRIPTION........................19-9
KEYLESS ENTRY - INSPECTION.........30-11
KEYLESS ENTRY SYSTEM -
DESCRIPTION, REMOTE................8N-2
KEYLESS ENTRY SYSTEM - DIAGNOSIS
AND TESTING, POWER LOCK &
REMOTE............................8N-4
KEYLESS ENTRY SYSTEM - OPERATION,
REMOTE............................8N-3
KEYLESS ENTRY TRANSMITTER -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-7
KEYLESS ENTRY TRANSMITTER -
OPERATION, REMOTE..................8N-7
KNOB - INSTALLATION, TURNING LOOP
HEIGHT ADJUSTER
...................8O-30
KNOB - REMOVAL, TURNING LOOP
HEIGHT ADJUSTER
...................8O-30
KNUCKLE - DESCRIPTION
............2-20,2-9
KNUCKLE - INSTALLATION
..........2-10,2-20
KNUCKLE - OPERATION
............2-10,2-20KNUCKLE - REMOVAL..............2-10,2-20
LABEL - DESCRIPTION, VECI.........Intro.-10
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION....................Intro.-12
LABEL - OPERATION, VECI...........Intro.-10
LABELS - STANDARD PROCEDURE,
INSPECTION - INFORMATION...........30-22
LAMP - DESCRIPTION, READING........8L-36
LAMP - DESCRIPTION, TAIL............8L-29
LAMP - DIAGNOSIS AND TESTING, FOG . . . 8L-9
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - INSTALLATION, CLEARANCE......8L-6
LAMP - INSTALLATION, DOME..........8L-33
LAMP - INSTALLATION, FOG............8L-11
LAMP - INSTALLATION, LICENSE PLATE . . 8L-22
LAMP - INSTALLATION, MARKER........8L-23
LAMP - INSTALLATION, OUTBOARD
IDENTIFICATION.....................8L-29
LAMP - INSTALLATION, PARK/TURN
SIGNAL............................8L-29
LAMP - INSTALLATION, READING........8L-36
LAMP - INSTALLATION, TAIL...........8L-30
LAMP - INSTALLATION, UNDERHOOD....8L-32
LAMP - INSTALLATION, VANITY.........8L-37
LAMP - OPERATION, READING..........8L-36
LAMP - OPERATION, TAIL..............8L-29
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - REMOVAL, CLEARANCE..........8L-6
LAMP - REMOVAL, DOME..............8L-33
LAMP - REMOVAL, FOG...............8L-11
LAMP - REMOVAL, LICENSE PLATE......8L-22
LAMP - REMOVAL, MARKER...........8L-22
LAMP - REMOVAL, OUTBOARD
IDENTIFICATION.....................8L-28
LAMP - REMOVAL, PARK/TURN SIGNAL . . 8L-29
LAMP - REMOVAL, READING...........8L-36
LAMP - REMOVAL, TAIL...............8L-29
LAMP - REMOVAL, UNDERHOOD........8L-31
LAMP - REMOVAL, VANITY.............8L-37
LAMP AND SWITCH - INSTALLATION,
GLOVE BOX.........................8L-35
LAMP AND SWITCH - REMOVAL, GLOVE
BOX ...............................8L-35
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-24
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR.............8J-24
LAMP MODULE - DESCRIPTION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - INSTALLATION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - OPERATION, DAYTIME
RUNNING............................8L-9
LAMP MODULE - REMOVAL, DAYTIME
RUNNING............................8L-9
LAMP SWITCH - DESCRIPTION, BRAKE....8L-4
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE......................8L-5
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-5
LAMP SWITCH - OPERATION, BRAKE......8L-4
LAMP SWITCH - REMOVAL, BRAKE.......8L-5
LAMP UNIT - ADJUSTMENTS, FOG.......8L-12
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-6
LAMP UNIT - INSTALLATION, FOG.......8L-12
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-22
LAMP UNIT - INSTALLATION, PARK/
TURN SIGNAL.......................8L-29
LAMP UNIT - INSTALLATION, TAIL.......8L-30
LAMP UNIT - INSTALLATION,
UNDERHOOD........................8L-32
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP UNIT - REMOVAL, FOG...........8L-11
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-22
LAMP UNIT - REMOVAL, PARK/TURN
SIGNAL............................8L-29
LAMP UNIT - REMOVAL, TAIL...........8L-30
LAMP UNIT - REMOVAL, UNDERHOOD . . . 8L-32
LASH ADJUSTMENT AND VERIFICATION
- STANDARD PROCEDURE, VALVE
.......9-256
LATCH - ADJUSTMENT
...............23-100
LATCH - ADJUSTMENT, FRONT DOOR
....23-72
LATCH - INSTALLATION
....23-100,23-64,23-72
LATCH - INSTALLATION, SAFETY
.......23-102LATCH - LOWER - INSTALLATION........23-80
LATCH - LOWER - REMOVAL...........23-80
LATCH - REMOVAL........23-100,23-64,23-72
LATCH - REMOVAL, SAFETY...........23-102
LATCH - UPPER - INSTALLATION........23-81
LATCH - UPPER - REMOVAL............23-81
LATCH AND KEEPER - INSTALLATION,
BACKLITE.........................23-146
LATCH AND KEEPER - REMOVAL,
BACKLITE.........................23-146
LATCH HANDLE - INSTALLATION........23-65
LATCH HANDLE - REMOVAL............23-65
LATCH RELEASE CABLE - INSTALLATION . 23-101
LATCH RELEASE CABLE - REMOVAL....23-101
LATCH STRIKER - ADJUSTMENT.......23-102
LATCH STRIKER - INSTALLATION . 23-102,23-65,
23-73
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-113
LATCH STRIKER - LOWER -
INSTALLATION.......................23-82
LATCH STRIKER - LOWER - REMOVAL....23-82
LATCH STRIKER - REMOVAL.....23-102,23-65,
23-73
LATCH STRIKER - REMOVAL, GLOVE
BOX ..............................23-113
LATCH STRIKER - UPPER -
INSTALLATION.......................23-82
LATCH STRIKER - UPPER - REMOVAL....23-82
LATCH/SAFETY CATCH - INSPECTION,
HOOD..............................30-4
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID . . . 21-148,21-319,
21-491,21-662
LEAK DETECTION PUMP - DESCRIPTION . . 25-33
LEAK DETECTION PUMP - INSTALLATION . 25-34
LEAK DETECTION PUMP - REMOVAL.....25-34
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE..............14-2
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE....9-124,
9-179,9-67,9-9
LEAKAGE - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD.....9-110,9-165,9-222,9-53
LEAKAGE - DIAGNOSIS AND TESTING,
POWER STEERING GEAR..............19-14
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-31
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-5
LEAKS - DIAGNOSIS AND TESTING,
ENGINE OIL...........9-104,9-160,9-215,9-47
LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL LINE............14-74
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA.....................9-10
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-43
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURES,
REPAIRING..........................22-8
LEFT FRONT FENDER - INSTALLATION....23-93
LEFT FRONT FENDER - REMOVAL.......23-92
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID . . 21-199,21-370,
21-545,21-715
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-14
LEVEL - STANDARD PROCEDURE,
CHECKING BATTERY ELECTROLYTE.......8F-8
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-57
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-16
LEVEL CHECK - STANDARD
PROCEDURE, FLUID.....21-199,21-370,21-545,
21-715
LEVEL, OIL - STANDARD PROCEDURE-
ENGINE OIL
.........................9-295
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
..............14-7,14-73
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
..................14-9
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
................14-7,14-73
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-8
20 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - INSTALLATION,
WASHER FLUID......................8R-8
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-7
LEVEL SWITCH - REMOVAL, WASHER
FLUID..............................8R-8
LEVELS - INSPECTION, FLUID...........30-4
LEVER - ADJUSTMENT, SHIFT . . . 21-853,21-888,
21-925
LEVER - INSTALLATION, GEAR SHIFT.....19-13
LEVER - INSTALLATION, SHIFT . . 21-853,21-888,
21-924
LEVER - REMOVAL, GEAR SHIFT........19-13
LEVER - REMOVAL, SHIFT......21-852,21-887,
21-924
LICENSE PLATE LAMP - INSTALLATION . . . 8L-22
LICENSE PLATE LAMP - REMOVAL.......8L-22
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-22
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-22
LID - INSTALLATION, CENTER CONSOLE . 23-132
LID - REMOVAL, CENTER CONSOLE.....23-131
LIFTERS - CLEANING, HYDRAULIC . . 9-152,9-208
LIFTERS - INSTALLATION, HYDRAULIC . . . 9-152,
9-208
LIFTERS - REMOVAL, HYDRAULIC . . 9-152,9-207
LIFTERS (CAM IN BLOCK) - CLEANING,
HYDRAULIC......................9-39,9-96
LIFTERS (CAM IN BLOCK) -
INSTALLATION, HYDRAULIC.........9-39,9-96
LIFTERS (CAM IN BLOCK) - REMOVAL,
HYDRAULIC......................9-39,9-96
LIFTERS/TAPPETS - CLEANING, SOLID....9-281
LIFTERS/TAPPETS - INSPECTION, SOLID . . 9-281
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-281
LIFTERS/TAPPETS - REMOVAL, SOLID....9-280
LIGHT DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L) MAINTENANCE
SCHEDULES, MAINTENANCE
SCHEDULES..........................0-7
LIGHTER - DIAGNOSIS & TESTING,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - INSTALLATION,
CIGAR...........................8W-97-3
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-3
LIGHTS - INSPECTION, GAUGES/
WARNING..........................30-19
LIGHTS AND SWITCHES - INSPECTION . . . 30-12
LINE - INSTALLATION, LIQUID..........24-52
LINE - INSTALLATION, SUCTION AND
DISCHARGE.........................24-51
LINE - REMOVAL, LIQUID..............24-52
LINE - REMOVAL, SUCTION AND
DISCHARGE.........................24-50
LINE COUPLERS - DESCRIPTION, A/C....24-40
LINE COUPLERS - OPERATION, A/C......24-41
LINE COUPLERS - STANDARD
PROCEDURE, A/C....................24-43
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-74
LINER - INSTALLATION, REAR
WHEELHOUSE.......................23-96
LINER - REMOVAL, REAR WHEELHOUSE . . 23-96
LINES - CLEANING AND INSPECTION,
OIL COOLER........................9-296
LINES - DESCRIPTION, FUEL.......14-73,14-9
LINES - DESCRIPTION, HIGH PRESSURE
FUEL..............................14-74
LINES - INSTALLATION, FUEL...........14-77
LINES - OPERATION, HIGH PRESSURE
FUEL..............................14-74
LINES - REMOVAL, FUEL..............14-75
LINES/HOSES - INSPECTION.............30-6
LINK CONNECTOR - DESCRIPTION, DATA . 8E-12
LINK CONNECTOR - OPERATION, DATA . . . 8E-12
LINKAGE - 2WD - DESCRIPTION........19-38
LINKAGE - 2WD - INSTALLATION........19-39
LINKAGE - 2WD - REMOVAL
............19-38
LINKAGE - 4WD - DESCRIPTION
........19-40
LINKAGE - 4WD - INSTALLATION
........19-41
LINKAGE - 4WD - REMOVAL
............19-40
LINKAGE - DESCRIPTION
...............6-19LINKAGE - INSTALLATION...............6-20
LINKAGE - OPERATION.................6-20
LINKAGE - REMOVAL..................6-20
LINKAGE, SPECIAL TOOLS - STEERING . . . 19-39,
19-42
LINK/COIL SUSPENSION - STANDARD
PROCEDURES, ALIGNMENT..............2-5
LINK/COIL SUSPENSION, SPECIAL
TOOLS..............................2-16
LIQUID LINE - INSTALLATION...........24-52
LIQUID LINE - REMOVAL..............24-52
LOAD TEST - STANDARD PROCEDURE....8F-14
LOADS - STANDARD PROCEDURE,
TESTING FOR SHORT TO GROUND ON
FUSES POWERING SEVERAL.........8W-01-7
LOCATIONS - DESCRIPTION, SPLICE . . . 8W-95-1
LOCATIONS, SPECIFICATIONS - BODY
SEALER............................23-47
LOCATIONS, SPECIFICATIONS -
STRUCTURAL ADHESIVE...............23-44
LOCATIONS, SPECIFICATIONS - WELD.....23-4
LOCK & REMOTE KEYLESS ENTRY
SYSTEM - DIAGNOSIS AND TESTING,
POWER.............................8N-4
LOCK - STANDARD PROCEDURE,
HYDROSTATIC.....9-11,9-125,9-181,9-238,9-68
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY....19-10
LOCK CYLINDER - INSTALLATION.......23-73
LOCK CYLINDER - REMOVAL...........23-73
LOCK CYLINDER HOUSING -
INSTALLATION.......................19-11
LOCK CYLINDER HOUSING - REMOVAL . . . 19-10
LOCK CYLINDERS - DESCRIPTION........23-1
LOCK MOTOR - DESCRIPTION, POWER....8N-6
LOCK MOTOR - DIAGNOSIS AND
TESTING, POWER.....................8N-7
LOCK MOTOR - OPERATION, POWER.....8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - DESCRIPTION, POWER . . . 8N-8
LOCK SWITCH - DIAGNOSIS & TESTING,
DOOR CYLINDER.....................8N-5
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-8
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER...........................8N-6
LOCK SWITCH - OPERATION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - OPERATION, POWER.....8N-8
LOCK SWITCH - REMOVAL, DOOR
CYLINDER...........................8N-6
LOCK SYSTEM - DESCRIPTION, POWER . . . 8N-1
LOCK SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LOCK SYSTEM - OPERATION, POWER.....8N-3
LOCKS - INSPECTION, DOORS AND
DOOR.............................30-11
LOCKS - INSPECTION, WINDOWS,
DOORS............................30-14
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-29
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-29
LOOP HEIGHT ADJUSTER KNOB -
INSTALLATION, TURNING..............8O-30
LOOP HEIGHT ADJUSTER KNOB -
REMOVAL, TURNING.................8O-30
LOOSE ITEMS - INSTALLATION, SHIPPED . 30-14
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-23
LOW FUEL INDICATOR - OPERATION.....8J-23
LOW MOUNTED - INSTALLATION, SIDE
VIEW MIRROR.......................23-98
LOW MOUNTED - REMOVAL, SIDE VIEW
MIRROR...........................23-98
LOW PRESSURE SWITCH -
DESCRIPTION, A/C...................24-21
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-21
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-22
LOW PRESSURE SWITCH - OPERATION,
A/C
................................24-21
LOW PRESSURE SWITCH - REMOVAL,
A/C
................................24-21
LOWER - INSTALLATION, LATCH
........23-80
LOWER - INSTALLATION, LATCH
STRIKER
...........................23-82LOWER - REMOVAL, LATCH............23-80
LOWER - REMOVAL, LATCH STRIKER....23-82
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-10
LOWER BALL JOINT - INSTALLATION......2-25
LOWER CONTROL ARM - INSTALLATION . . 2-10,
2-20
LOWER CONTROL ARM - REMOVAL . . 2-10,2-20
LOWER FASCIA - INSTALLATION, FRONT . . . 13-3
LOWER FASCIA - REMOVAL, FRONT......13-3
LUBRICANTS - STANDARD PROCEDURE,
CLASSIFICATION OF....................0-3
LUBRICATION - DESCRIPTION.....9-102,9-158,
9-214,9-292,9-45
LUBRICATION - DIAGNOSIS AND
TESTING...............9-123,9-178,9-66,9-8
LUBRICATION - OPERATION . 9-102,9-158,9-214,
9-292,9-45
LUBRICATION - STANDARD PROCEDURE . 19-38,
19-40
LUMBAR ADJUSTER - DIAGNOSIS &
TESTING, POWER....................8N-18
LUMBAR CONTROL SWITCH -
DESCRIPTION.......................8N-17
LUMBAR CONTROL SWITCH -
OPERATION.........................8N-18
LUMBAR CONTROL SWITCH - REMOVAL . 8N-18
LUMBAR MOTOR - DESCRIPTION.......8N-18
LUMBAR MOTOR - OPERATION.........8N-18
LUMBAR SUPPORT - INSTALLATION....23-133
LUMBAR SUPPORT - REMOVAL........23-133
MACHINING - STANDARD PROCEDURE,
BRAKE DRUM........................5-33
MAIN BEARING CLEARANCE -
STANDARD PROCEDURE...............9-275
MAIN BEARING FITTING - STANDARD
PROCEDURE....................9-203,9-33
MAIN BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT........9-146,9-90
MAIN BEARINGS - DESCRIPTION,
CRANKSHAFT...............9-146,9-32,9-90
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT..........9-147,9-204,9-34,9-90
MAIN BEARINGS - OPERATION,
CRANKSHAFT...............9-146,9-32,9-90
MAIN BEARINGS - REMOVAL,
CRANKSHAFT..........9-147,9-204,9-33,9-90
MAINTENANCE SCHEDULE (8.0L 2500 &
3500 MODELS - CALIFORNIA ONLY) -
DESCRIPTION, MEDIUM DUTY TRUCK.....0-13
MAINTENANCE SCHEDULES - 24-VALVE
CUMMINS TURBO DIESEL -
DESCRIPTION........................0-22
MAINTENANCE SCHEDULES -
DESCRIPTION, HEAVY DUTY ENGINE
(FEDERAL ONLY - 2500 8.0L HD AND
3500 5.9L& 8.0L MODELS)..............0-17
MAINTENANCE SCHEDULES - LIGHT
DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L) MAINTENANCE
SCHEDULES..........................0-7
MAINTENANCE SCHEDULES,
MAINTENANCE SCHEDULES - LIGHT
DUTY ENGINE (1500 AND 2500
MODELS EXCEPT 8.0L)..................0-7
MALFUNCTION INDICATOR LAMP (MIL) -
DESCRIPTION.......................8J-24
MALFUNCTION INDICATOR LAMP (MIL) -
OPERATION.........................8J-24
MANAGER - DESCRIPTION, TASK........25-15
MANAGER - OPERATION, TASK.........25-19
MANIFOLD - CLEANING, EXHAUST . 9-112,9-168,
9-225,9-304,9-55
MANIFOLD - CLEANING, INTAKE . . . 9-110,9-166,
9-223,9-302,9-53
MANIFOLD - DESCRIPTION, EXHAUST . . . 9-112,
9-168,9-224,9-55
MANIFOLD - DESCRIPTION, FUEL DRAIN . . 14-86
MANIFOLD - DESCRIPTION, INTAKE
.....9-109,
9-165,9-222,9-52
MANIFOLD - INSPECTION, EXHAUST
.....9-112,
9-168,9-225,9-304,9-55
MANIFOLD - INSPECTION, INTAKE
. 9-110,9-166,
9-223,9-302,9-53
MANIFOLD - INSTALLATION, EXHAUST
. . . 9-113,
9-168,9-225,9-304,9-55
MANIFOLD - INSTALLATION, FUEL
DRAIN
.............................14-86
BR/BEINDEX 21
Description Group-Page Description Group-Page Description Group-Page

TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLER AND TUBES - WITHOUT
RADIATOR IN-TANK...........7-80,7-83,7-86
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITH
RADIATOR IN-TANK...........7-79,7-83,7-85
TRANSMISSION OVERTEMP INDICATOR
- DESCRIPTION......................8J-31
TRANSMISSION OVERTEMP INDICATOR
- OPERATION........................8J-31
TRANSMISSION, SPECIAL TOOLS -
NV5600 MANUAL...................21-127
TRANSMISSION, SPECIAL TOOLS - RE . . 21-534,
21-704
TRANSMISSION, SPECIFICATIONS......21-186,
21-532,21-702
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION . . . 21-262,21-433,21-606,21-779
TRANSMISSION TEMPERATURE SENSOR
- OPERATION.....21-262,21-433,21-606,21-779
TRANSMISSION THROTTLE VALVE
CABLE - ADJUSTMENTS . 21-254,21-425,21-598,
21-771
TRANSMISSIONS, SPECIAL TOOLS - RE . 21-188,
21-359
TRANSMISSION/TRANSFER CASE -
INSPECTION........................30-15
TRANSMITTER - DESCRIPTION, REMOTE
KEYLESS ENTRY......................8N-7
TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS ENTRY......8N-7
TRANSMITTER - OPERATION, REMOTE
KEYLESS ENTRY......................8N-7
TRANSMITTER BATTERIES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE, RKE...........8N-8
TRAY - DESCRIPTION, BATTERY.........8F-24
TRAY - INSTALLATION, BATTERY........8F-25
TRAY - INSTALLATION, REAR FLOOR
STOWAGE.........................23-121
TRAY - OPERATION, BATTERY..........8F-25
TRAY - REMOVAL, BATTERY............8F-25
TRAY - REMOVAL, REAR FLOOR
STOWAGE.........................23-121
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-7
TRIM - INSTALLATION, A-PILLAR.......23-119
TRIM - INSTALLATION, B-PILLAR.......23-120
TRIM - INSTALLATION, C-PILLAR.......23-128
TRIM - INSTALLATION, DOOR SILL.....23-121
TRIM - INSTALLATION, GLOVE BOX
OPENING UPPER....................23-114
TRIM - INSTALLATION, REAR CLOSURE
PANEL............................23-121
TRIM - REMOVAL, A-PILLAR..........23-119
TRIM - REMOVAL, B-PILLAR..........23-120
TRIM - REMOVAL, C-PILLAR..........23-128
TRIM - REMOVAL, DOOR SILL.........23-121
TRIM - REMOVAL, GLOVE BOX OPENING
UPPER............................23-114
TRIM - REMOVAL, REAR CLOSURE
PANEL............................23-120
TRIM COVER - INSTALLATION, COWL . . . 23-120
TRIM COVER - REMOVAL, COWL.......23-119
TRIM PANEL - INSTALLATION......23-74,23-84
TRIM PANEL - INSTALLATION, QUARTER . 23-128
TRIM PANEL - REMOVAL.........23-74,23-84
TRIM PANEL - REMOVAL, QUARTER....23-127
TRIP COMPUTER/MAINTENANCE
REMINDER - INSPECTION..............30-17
TRIP DEFINITION - DESCRIPTION........25-18
TROUBLE CODES - DESCRIPTION,
DIAGNOSTIC.........................25-2
TRUCK MAINTENANCE SCHEDULE (8.0L
2500 & 3500 MODELS - CALIFORNIA
ONLY) - DESCRIPTION, MEDIUM DUTY....0-13
TUBE - DESCRIPTION, A/C ORIFICE
......24-53
TUBE - DIAGNOSIS AND TESTING, FIXED
ORIFICE
............................24-54
TUBE - OPERATION, A/C ORIFICE
........24-53
TUBE - REMOVAL, A/C ORIFICE
.........24-54
TUBES - WITH RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS
...................7-79,7-83,7-85TUBES - WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLER....................7-80,7-83,7-86
TURBO DIESEL - DESCRIPTION,
MAINTENANCE SCHEDULES -
24-VALVE CUMMINS...................0-22
TURBOCHARGER - CLEANING..........11-16
TURBOCHARGER - DESCRIPTION........11-13
TURBOCHARGER - INSPECTION.........11-16
TURBOCHARGER - INSTALLATION.......11-16
TURBOCHARGER - OPERATION.........11-13
TURBOCHARGER - REMOVAL...........11-15
TURN AND EMERGENCY SIGNALS -
INSPECTION........................30-19
TURN SIGNAL & HAZARD WARNING
SYSTEM - DESCRIPTION...............8L-2
TURN SIGNAL & HAZARD WARNING
SYSTEM - DIAGNOSIS AND TESTING......8L-3
TURN SIGNAL & HAZARD WARNING
SYSTEM - OPERATION.................8L-2
TURN SIGNAL CANCEL CAM -
DESCRIPTION.......................8L-30
TURN SIGNAL CANCEL CAM -
OPERATION.........................8L-31
TURN SIGNAL INDICATORS -
DESCRIPTION.......................8J-32
TURN SIGNAL INDICATORS - DIAGNOSIS
AND TESTING.......................8J-32
TURN SIGNAL INDICATORS -
OPERATION.........................8J-32
TURNING LOOP ADJUSTER -
INSTALLATION, SEAT BELT..............8O-29
TURNING LOOP ADJUSTER - REMOVAL,
SEAT BELT .........................8O-29
TURNING LOOP HEIGHT ADJUSTER
KNOB - INSTALLATION................8O-30
TURNING LOOP HEIGHT ADJUSTER
KNOB - REMOVAL....................8O-30
TWEETER SPEAKER - INSTALLATION,
A-PILLAR...........................8A-19
TWEETER SPEAKER - REMOVAL,
A-PILLAR...........................8A-19
UNDERHOOD LAMP - INSTALLATION.....8L-32
UNDERHOOD LAMP - REMOVAL.........8L-31
UNDERHOOD LAMP UNIT -
INSTALLATION.......................8L-32
UNDERHOOD LAMP UNIT - REMOVAL....8L-32
UNIT - ADJUSTMENTS, FOG LAMP.......8L-12
UNIT - ADJUSTMENTS, HEADLAMP......8L-21
UNIT - ASSEMBLY, OVERDRIVE . . 21-225,21-395,
21-569,21-742
UNIT - CLEANING, OVERDRIVE . . 21-224,21-394,
21-568,21-741
UNIT - DIAGNOSIS AND TESTING, FUEL
GAUGE SENDING......................14-8
UNIT - DISASSEMBLY, OVERDRIVE.....21-217,
21-387,21-562,21-734
UNIT - INSPECTION, OVERDRIVE......21-224,
21-394,21-569,21-741
UNIT - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP.................8L-6
UNIT - INSTALLATION, FOG LAMP.......8L-12
UNIT - INSTALLATION, HEADLAMP.......8L-20
UNIT - INSTALLATION, LICENSE PLATE
LAMP..............................8L-22
UNIT - INSTALLATION, OVERDRIVE.....21-234,
21-404,21-577,21-750
UNIT - INSTALLATION, PARK/TURN
SIGNAL LAMP.......................8L-29
UNIT - INSTALLATION, TAIL LAMP.......8L-30
UNIT - INSTALLATION, UNDERHOOD
LAMP..............................8L-32
UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP.................8L-6
UNIT - REMOVAL, FOG LAMP...........8L-11
UNIT - REMOVAL, HEADLAMP..........8L-20
UNIT - REMOVAL, LICENSE PLATE LAMP . . 8L-22
UNIT - REMOVAL, OVERDRIVE . . 21-216,21-387,
21-560,21-733
UNIT - REMOVAL, PARK/TURN SIGNAL
LAMP
..............................8L-29
UNIT - REMOVAL, TAIL LAMP
...........8L-30
UNIT - REMOVAL, UNDERHOOD LAMP
. . . 8L-32
UNIT / SENSOR - DESCRIPTION, FUEL
LEVEL SENDING
.................14-7,14-73
UNIT / SENSOR - INSTALLATION, FUEL
LEVEL SENDING
......................14-9UNIT / SENSOR - OPERATION, FUEL
LEVEL SENDING.................14-7,14-73
UNIT / SENSOR - REMOVAL, FUEL
LEVEL SENDING......................14-8
UNIVERSAL JOINTS - DISASSEMBLY,
SINGLE CARDAN......................3-11
UNIVERSAL JOINTS - INSTALLATION,
SINGLE CARDAN..................3-34,3-66
UNIVERSAL JOINTS - REMOVAL, SINGLE
CARDAN........................3-33,3-65
UP/DOWN - ADJUSTMENT, FRONT DOOR . 23-69
UPPER - INSTALLATION, LATCH.........23-81
UPPER - INSTALLATION, LATCH
STRIKER...........................23-82
UPPER - REMOVAL, LATCH............23-81
UPPER - REMOVAL, LATCH STRIKER.....23-82
UPPER BALL JOINT - DIAGNOSIS AND
TESTING............................2-12
UPPER BALL JOINT - INSTALLATION......2-25
UPPER CONTROL ARM - INSTALLATION . . . 2-13,
2-24
UPPER CONTROL ARM - REMOVAL . . . 2-13,2-23
UPPER CORNER SEAL - INSTALLATION,
FRONT DOOR......................23-154
UPPER CORNER SEAL - REMOVAL,
FRONT DOOR......................23-154
UPPER TRIM - INSTALLATION, GLOVE
BOX OPENING......................23-114
UPPER TRIM - REMOVAL, GLOVE BOX
OPENING..........................23-114
UPSHIFT INDICATOR - DESCRIPTION.....8J-33
UPSHIFT INDICATOR - OPERATION.......8J-33
USAGE - DESCRIPTION, FASTENER.....Intro.-6
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
V-10 - DESCRIPTION, 8.0L..............8I-1
V-10 - OPERATION, 8.0L................8I-1
V-10 ENGINE - IGNITION COIL
RESISTANCE, 8.0L.....................8I-3
V-10 ENGINE - SPARK PLUG CABLE
ORDER, 8.0L.........................8I-2
V-6 ENGINE - ENGINE FIRING ORDER,
3.9L................................8I-2
V-6/V-8 - DESCRIPTION.................8I-1
V-6/V-8 - OPERATION..................8I-1
V-6/V-8 ENGINES - DESCRIPTION........25-35
V-6/V-8 ENGINES - DIAGNOSIS AND
TESTING, PCV VALVE.................25-36
V-6/V-8 ENGINES - OPERATION.........25-35
V-8 ENGINES - ENGINE FIRING ORDER,
5.2L/5.9L............................8I-2
VACUUM CHECK VALVE - DESCRIPTION . . 24-28
VACUUM CHECK VALVE - INSTALLATION . . 24-29
VACUUM CHECK VALVE - OPERATION....24-28
VACUUM CHECK VALVE - REMOVAL......24-29
VACUUM MOTOR - ASSEMBLY, AXLE . . 3-33,3-65
VACUUM MOTOR - DESCRIPTION, AXLE . . . 3-29,
3-62
VACUUM MOTOR - DIAGNOSIS AND
TESTING........................3-31,3-63
VACUUM MOTOR - DISASSEMBLY, AXLE . . 3-33,
3-65
VACUUM MOTOR - INSTALLATION, AXLE . . 3-33,
3-65
VACUUM MOTOR - OPERATION, AXLE . 3-30,3-62
VACUUM MOTOR - REMOVAL, AXLE . . 3-33,3-65
VACUUM PUMP - 5.9L DIESEL -
DESCRIPTION........................7-34
VACUUM PUMP - 5.9L DIESEL -
INSTALLATION
........................7-37
VACUUM PUMP - 5.9L DIESEL -
OPERATION
..........................7-35
VACUUM PUMP - 5.9L DIESEL -
REMOVAL
...........................7-35
VACUUM PUMP OUTPUT - DIAGNOSIS
AND TESTING
........................7-35
VACUUM RESERVOIR - DESCRIPTION
....24-29
VACUUM RESERVOIR - DESCRIPTION
....8P-13
VACUUM RESERVOIR - INSTALLATION
....24-30
VACUUM RESERVOIR - INSTALLATION
. . . 8P-14
VACUUM RESERVOIR - OPERATION
......24-29
VACUUM RESERVOIR - REMOVAL
.......24-30
VACUUM RESERVOIR - REMOVAL
.......8P-13
VACUUM SCHEMATICS - DIAGNOSIS
AND TESTING
.......................25-37
VACUUM SUPPLY - DIAGNOSIS AND
TESTING
............................8P-2
BR/BEINDEX 37
Description Group-Page Description Group-Page Description Group-Page