trailer DODGE RAM 2002 Service Owner's Guide

FLUID AND FILTER
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - EFFECTS OF
INCORRECT FLUID LEVEL
A low fluid level allows the pump to take in air
along with the fluid. Air in the fluid will cause fluid
pressures to be low and develop slower than normal.
If the transmission is overfilled, the gears churn the
fluid into foam. This aerates the fluid and causing
the same conditions occurring with a low level. In
either case, air bubbles cause fluid overheating, oxi-
dation and varnish buildup which interferes with
valve and clutch operation. Foaming also causes fluid
expansion which can result in fluid overflow from the
transmission vent or fill tube. Fluid overflow can eas-
ily be mistaken for a leak if inspection is not careful.
DIAGNOSIS AND TESTING - CAUSES OF
BURNT FLUID
Burnt, discolored fluid is a result of overheating
which has two primary causes.
(1) A result of restricted fluid flow through the
main and/or auxiliary cooler. This condition is usu-
ally the result of a faulty or improperly installed
drainback valve, a damaged main cooler, or severe
restrictions in the coolers and lines caused by debris
or kinked lines.
(2) Heavy duty operation with a vehicle not prop-
erly equipped for this type of operation. Trailer tow-
ing or similar high load operation will overheat the
transmission fluid if the vehicle is improperly
equipped. Such vehicles should have an auxiliary
transmission fluid cooler, a heavy duty cooling sys-
tem, and the engine/axle ratio combination needed to
handle heavy loads.
DIAGNOSIS AND TESTING - FLUID
CONTAMINATION
Transmission fluid contamination is generally a
result of:
²adding incorrect fluid
²failure to clean dipstick and fill tube when
checking level
²engine coolant entering the fluid
²internal failure that generates debris
²overheat that generates sludge (fluid break-
down)
²failure to reverse flush cooler and lines after
repair
²failure to replace contaminated converter after
repair
The use of non-recommended fluids can result in
transmission failure. The usual results are erratic
shifts, slippage, abnormal wear and eventual failure
due to fluid breakdown and sludge formation. Avoid
this condition by using recommended fluids only.
The dipstick cap and fill tube should be wiped
clean before checking fluid level. Dirt, grease and
other foreign material on the cap and tube could fall
into the tube if not removed beforehand. Take the
time to wipe the cap and tube clean before withdraw-
ing the dipstick.
Engine coolant in the transmission fluid is gener-
ally caused by a cooler malfunction. The only remedy
is to replace the radiator as the cooler in the radiator
is not a serviceable part. If coolant has circulated
through the transmission, an overhaul is necessary.
The transmission cooler and lines should be
reverse flushed whenever a malfunction generates
sludge and/or debris. The torque converter should
also be replaced at the same time.
Failure to flush the cooler and lines will result in
recontamination. Flushing applies to auxiliary coolers
as well. The torque converter should also be replaced
whenever a failure generates sludge and debris. This is
necessary because normal converter flushing procedures
will not remove all contaminants.
STANDARD PROCEDURE
STANDARD PROCEDURE - FLUID LEVEL
CHECK
Low fluid level can cause a variety of conditions
because it allows the pump to take in air along with
the fluid. As in any hydraulic system, air bubbles
make the fluid spongy, therefore, pressures will be
low and build up slowly.
Improper filling can also raise the fluid level too
high. When the transmssion has too much fluid, the
geartrain churns up foam and cause the same condi-
tions which occur with a low fluid level.
Fig. 88 Installing Overdrive Housing Seal
1 - SPECIAL TOOL C-3995-A OR C-3972-A
2 - SPECIAL TOOL C-4471
BR/BEAUTOMATIC TRANSMISSION - 46RE 21 - 157
EXTENSION HOUSING SEAL (Continued)

INSTALLATION
(1) Place seal in position on overdrive housing.
(2) Drive seal into overdrive housing with Seal
Installer C-3995-A (Fig. 82).
(3) Carefully guide propeller shaft slip yoke into
housing and onto output shaft splines. Align marks
made at removal and connect propeller shaft to rear
axle pinion yoke.
FLUID AND FILTER
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - EFFECTS OF
INCORRECT FLUID LEVEL
A low fluid level allows the pump to take in air
along with the fluid. Air in the fluid will cause fluid
pressures to be low and develop slower than normal.
If the transmission is overfilled, the gears churn the
fluid into foam. This aerates the fluid and causing
the same conditions occurring with a low level. In
either case, air bubbles cause fluid overheating, oxi-
dation and varnish buildup which interferes with
valve and clutch operation. Foaming also causes fluidexpansion which can result in fluid overflow from the
transmission vent or fill tube. Fluid overflow can eas-
ily be mistaken for a leak if inspection is not careful.
DIAGNOSIS AND TESTING - CAUSES OF
BURNT FLUID
Burnt, discolored fluid is a result of overheating
which has two primary causes.
(1) A result of restricted fluid flow through the
main and/or auxiliary cooler. This condition is usu-
ally the result of a faulty or improperly installed
drainback valve, a damaged main cooler, or severe
restrictions in the coolers and lines caused by debris
or kinked lines.
(2) Heavy duty operation with a vehicle not prop-
erly equipped for this type of operation. Trailer tow-
ing or similar high load operation will overheat the
transmission fluid if the vehicle is improperly
equipped. Such vehicles should have an auxiliary
transmission fluid cooler, a heavy duty cooling sys-
tem, and the engine/axle ratio combination needed to
handle heavy loads.
DIAGNOSIS AND TESTING - FLUID
CONTAMINATION
Transmission fluid contamination is generally a
result of:
²adding incorrect fluid
²failure to clean dipstick and fill tube when
checking level
²engine coolant entering the fluid
²internal failure that generates debris
²overheat that generates sludge (fluid break-
down)
²failure to reverse flush cooler and lines after
repair
²failure to replace contaminated converter after
repair
The use of non-recommended fluids can result in
transmission failure. The usual results are erratic
shifts, slippage, abnormal wear and eventual failure
due to fluid breakdown and sludge formation. Avoid
this condition by using recommended fluids only.
The dipstick cap and fill tube should be wiped
clean before checking fluid level. Dirt, grease and
other foreign material on the cap and tube could fall
into the tube if not removed beforehand. Take the
time to wipe the cap and tube clean before withdraw-
ing the dipstick.
Engine coolant in the transmission fluid is gener-
ally caused by a cooler malfunction. The only remedy
is to replace the radiator as the cooler in the radiator
is not a serviceable part. If coolant has circulated
through the transmission, an overhaul is necessary.
The transmission cooler and lines should be
reverse flushed whenever a malfunction generates
Fig. 81 Removing Overdrive Housing Yoke Seal
1 - SPECIAL TOOL C-3985-B
2 - SEAL
Fig. 82 Installing Overdrive Housing Seal
1 - SPECIAL TOOL C-3995-A OR C-3972-A
2 - SPECIAL TOOL C-4471
BR/BEAUTOMATIC TRANSMISSION - 47RE 21 - 327
EXTENSION HOUSING SEAL (Continued)

HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER....................8L-6
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER....................8L-6
HIGH PRESSURE FUEL LINES -
DESCRIPTION.......................14-78
HIGH PRESSURE FUEL LINES -
OPERATION.........................14-78
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-46
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-47
HIGH PRESSURE SWITCH -
DESCRIPTION, A/C...................24-20
HIGH PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-20
HIGH PRESSURE SWITCH -
INSTALLATION, A/C...................24-20
HIGH PRESSURE SWITCH - OPERATION,
A/C................................24-20
HIGH PRESSURE SWITCH - REMOVAL,
A/C................................24-20
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-7
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-78
HINGE - INSTALLATION.....23-100,23-72,23-80
HINGE - REMOVAL........23-100,23-72,23-79
HITCH - INSTALLATION, TRAILER.........13-11
HITCH - REMOVAL, TRAILER...........13-11
HOISTING - STANDARD PROCEDURE.......0-9
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-17
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-18
HOLDDOWN - OPERATION, BATTERY.....8F-17
HOLDDOWN - REMOVAL, BATTERY......8F-17
HOLDER - INSTALLATION, CUP........23-110
HOLDER - REMOVAL, CUP............23-109
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-9
HONING - STANDARD PROCEDURE,
CYLINDER BORE..................9-11,9-65
HOOD - INSTALLATION...............23-101
HOOD - REMOVAL...................23-101
HOOK - INSTALLATION, COAT..........23-125
HOOK - INSTALLATION, FRONT TOW.....13-10
HOOK - REMOVAL, COAT.............23-124
HOOK - REMOVAL, FRONT TOW.........13-10
HORN - DESCRIPTION.............8H-1,8H-2
HORN - DIAGNOSIS AND TESTING.......8H-2
HORN - INSTALLATION.................8H-3
HORN - OPERATION...............8H-1,8H-2
HORN - REMOVAL....................8H-2
HORN RELAY - DESCRIPTION.......8W-97-12
HORN RELAY - DESCRIPTION...........8H-3
HORN RELAY - DIAGNOSIS AND
TESTING........................8W-97-12
HORN RELAY - DIAGNOSIS AND
TESTING............................8H-3
HORN RELAY - INSTALLATION.......8W-97-12
HORN RELAY - INSTALLATION...........8H-4
HORN RELAY - OPERATION.............8H-3
HORN RELAY - REMOVAL..........8W-97-12
HORN RELAY - REMOVAL..............8H-4
HORN SWITCH - DESCRIPTION..........8H-4
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-5
HORN SWITCH - OPERATION............8H-5
HORN SWITCH - REMOVAL.............8H-5
HOSE CLAMPS - DESCRIPTION...........7-4
HOSE CLAMPS - OPERATION.............7-4
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-76
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-73
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-77
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-76
HOSES - PRESSURE - DESCRIPTION
.....19-39
HOSES - PRESSURE - OPERATION
.......19-39
HOSES - RETURN - DESCRIPTION
.......19-39
HOSES - RETURN - OPERATION
.........19-39
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT
..............24-43HOSES/TUBES - DESCRIPTION, WASHER . . 8R-8
HOSES/TUBES - OPERATION, WASHER....8R-8
HOUSING - ASSEMBLY, HVAC...........24-36
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH..............................6-9
HOUSING - DISASSEMBLY, HVAC........24-35
HOUSING - INSTALLATION, CLUTCH......6-11
HOUSING - INSTALLATION, GEAR........9-188
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - REMOVAL, CLUTCH..........6-11
HOUSING - REMOVAL, GEAR...........9-187
HOUSING - REMOVAL, HVAC...........24-34
HOUSING BUSHING - INSTALLATION,
EXTENSION..................21-156,21-326
HOUSING BUSHING - REMOVAL,
EXTENSION..................21-156,21-326
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-460,21-497
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION.........21-460,21-497
HOUSING COVER - INSTALLATION, GEAR . 9-190
HOUSING COVER - REMOVAL, GEAR.....9-189
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER.........21-101,21-273
HOUSING INLET BAFFLE -
INSTALLATION, HVAC.................24-36
HOUSING INLET BAFFLE - REMOVAL,
HVAC..............................24-35
HOUSING PLUG - INSTALLATION,
STEERING GEAR.......................19-30
HOUSING PLUG - REMOVAL, STEERING
GEAR..............................19-29
HOUSING SEAL - INSTALLATION,
EXTENSION..................21-156,21-327
HOUSING SEAL - NV4500 -
INSTALLATION, ADAPTER..............21-42
HOUSING SEAL - NV4500 -
INSTALLATION, EXTENSION............21-42
HOUSING SEAL - NV4500 - REMOVAL,
ADAPTER...........................21-42
HOUSING SEAL - NV4500 - REMOVAL,
EXTENSION.........................21-42
HOUSING SEAL - NV5600 -
INSTALLATION, ADAPTER..............21-85
HOUSING SEAL - NV5600 -
INSTALLATION, EXTENSION............21-85
HOUSING SEAL - NV5600 - REMOVAL,
ADAPTER...........................21-85
HOUSING SEAL - NV5600 - REMOVAL,
EXTENSION.........................21-85
HOUSING SEAL - REMOVAL,
EXTENSION..................21-156,21-326
HUB / BEARING - INSTALLATION......2-17,2-9
HUB / BEARING - REMOVAL..........2-16,2-9
HVAC HOUSING - ASSEMBLY...........24-36
HVAC HOUSING - DISASSEMBLY........24-35
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
HVAC HOUSING INLET BAFFLE -
INSTALLATION.......................24-36
HVAC HOUSING INLET BAFFLE -
REMOVAL..........................24-35
HVAC SYSTEM AIRFLOW - DESCRIPTION . 24-30
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-18
HYDRAULIC LIFTERS - CLEANING
....9-37,9-92
HYDRAULIC LIFTERS - INSTALLATION
. 9-37,9-92
HYDRAULIC LIFTERS - REMOVAL
....9-37,9-92
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING
.......21-270,21-98
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS
..............21-132,21-302
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING
........................9-36,9-91
HYDRAULIC/MECHANICAL -
DESCRIPTION
.........................5-4
HYDRAULIC/MECHANICAL - WARNING
.....5-4
HYDROMETER TEST - STANDARD
PROCEDURE
........................8F-11
HYDROSTATIC LOCK - STANDARD
PROCEDURE
................9-11,9-122,9-66
IDENTIFICATION - DESCRIPTION,
FASTENER
.........................Intro.-6
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION
.............8W-01-6
IDENTIFICATION LAMP - INSTALLATION,
OUTBOARD
.........................8L-29IDENTIFICATION LAMP - REMOVAL,
OUTBOARD.........................8L-28
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-1
IDENTIFICATION PLATE - DESCRIPTION,
EQUIPMENT.......................Intro.-3
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-40
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-40
IGNITION - SPECIFICATIONS, TORQUE.....8I-2
IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-17
IGNITION CIRCUIT SENSE - OPERATION . . 8E-19
IGNITION COIL RESISTANCE, 5.9L
ENGINES............................8I-3
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-4
IGNITION SWITCH - DESCRIPTION.......19-11
IGNITION SWITCH - DESCRIPTION,
KEY-IN..............................19-9
IGNITION SWITCH - DIAGNOSIS AND
TESTING...........................19-11
IGNITION SWITCH - INSTALLATION......19-12
IGNITION SWITCH - OPERATION........19-11
IGNITION SWITCH - REMOVAL..........19-12
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING....19-9
IGNITION TIMING, SPECIFICATIONS.......8I-4
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-13
INDEPENDENT FRONT SUSPENSION,
SPECIAL TOOLS.......................2-9
INDICATOR - DESCRIPTION, ABS........8J-14
INDICATOR - DESCRIPTION, AIRBAG.....8J-15
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-15
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-17
INDICATOR - DESCRIPTION, CRUISE.....8J-18
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-20
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-21
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-22
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-26
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-27
INDICATOR - DESCRIPTION, SERVICE
REMINDER..........................8J-27
INDICATOR - DESCRIPTION, TRANS
OVERTEMP.........................8J-31
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-32
INDICATOR - DESCRIPTION, UPSHIFT....8J-32
INDICATOR - DESCRIPTION, VTSS........8Q-3
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-34
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-35
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-36
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-16
INDICATOR - DIAGNOSIS AND TESTING,
FOUR-WHEEL DRIVE..................8J-29
INDICATOR - DIAGNOSIS AND TESTING,
HIGH BEAM.........................8J-21
INDICATOR - DIAGNOSIS AND TESTING,
TURN SIGNAL
.......................8J-32
INDICATOR - DIAGNOSIS AND TESTING,
VTSS
...............................8Q-4
INDICATOR - DIAGNOSIS AND TESTING,
WASHER FLUID
......................8J-35
INDICATOR - OPERATION, ABS
..........8J-14
INDICATOR - OPERATION, AIRBAG
.......8J-15
INDICATOR - OPERATION, BRAKE/PARK
BRAKE
.............................8J-15
INDICATOR - OPERATION, CHECK
GAUGES
............................8J-17
INDICATOR - OPERATION, CRUISE
.......8J-18
INDICATOR - OPERATION, GEAR
SELECTOR
..........................8J-21
INDICATOR - OPERATION, HIGH BEAM
....8J-21
INDICATOR - OPERATION, LOW FUEL
.....8J-22
INDICATOR - OPERATION, OVERDRIVE
OFF
...............................8J-26
INDICATOR - OPERATION, SEATBELT
.....8J-27
16 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE COOLANT..........7-53
THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE COOLANT............7-54
THERMOSTAT - 8.0L - DESCRIPTION,
ENGINE COOLANT.....................7-51
THERMOSTAT - 8.0L - INSTALLATION,
ENGINE COOLANT.....................7-52
THERMOSTAT - 8.0L - OPERATION,
ENGINE COOLANT.....................7-51
THERMOSTAT - 8.0L - REMOVAL,
ENGINE COOLANT.....................7-51
THERMOSTAT - DIAGNOSIS AND
TESTING....................7-48,7-51,7-53
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM.......21-114,21-286
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-9
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN . . 9-11,9-122,9-66
THROTTLE BODY - DESCRIPTION........14-47
THROTTLE BODY - OPERATION.........14-47
THROTTLE CONTROL CABLE -
INSTALLATION.................14-110,14-50
THROTTLE CONTROL CABLE -
REMOVAL....................14-109,14-49
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-50
THROTTLE POSITION SENSOR -
OPERATION.........................14-50
THROTTLE VALVE CABLE -
ADJUSTMENTS, TRANSMISSION . 21-210,21-382
THROTTLE VALVE CABLE -
DESCRIPTION................21-209,21-381
TIMER MODULE - DESCRIPTION,
CENTRAL............................8E-1
TIMER MODULE - DIAGNOSIS AND
TESTING, CENTRAL....................8E-4
TIMER MODULE - INSTALLATION,
CENTRAL............................8E-6
TIMER MODULE - OPERATION, CENTRAL . . 8E-3
TIMER MODULE - REMOVAL, CENTRAL....8E-5
TIMING - DIAGNOSIS AND TESTING,
FUEL INJECTION PUMP...............14-70
TIMING BELT / CHAIN COVER(S) -
INSTALLATION...................9-110,9-54
TIMING BELT / CHAIN COVER(S) -
REMOVAL......................9-110,9-53
TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION...................9-111,9-55
TIMING BELT/CHAIN AND SPROCKETS -
REMOVAL......................9-111,9-54
TIMING CHAIN STRETCH - INSPECTION,
MEASURING....................9-111,9-54
TIMING, SPECIFICATIONS - IGNITION......8I-4
TIMING VERIFICATION - STANDARD
PROCEDURE........................9-187
TIRE - DESCRIPTION, SPARE...........22-10
TIRE - TEMPORARY - DESCRIPTION,
SPARE..............................22-6
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-4
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE INFLATION PRESSURES -
DESCRIPTION........................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-9
TIRE PRESSURE FOR HIGH SPEEDS -
DESCRIPTION........................22-7
TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS
......................22-9
TIRE ROTATION - STANDARD
PROCEDURE
.........................22-2
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING
........................22-8
TIRES - DESCRIPTION
.................22-6
TIRES - DESCRIPTION, RADIAL-PLY
.......22-6
TIRES - DESCRIPTION, REPLACEMENT
....22-7
TOOL, SPECIAL TOOLS - OVERHEAD
CONSOLE SPECIAL
...................8M-9
TOOLS - 5.9L DIESEL ENGINE, SPECIAL
. . 9-128
TOOLS - 5.9L ENGINE, SPECIAL
..........9-18
TOOLS - 8.0L ENGINE, SPECIAL
..........9-72
TOOLS - AUDIO SYSTEMS, SPECIAL
......8A-4
TOOLS - BASE BRAKES, SPECIAL
.........5-4
TOOLS - COOLING, SPECIAL
.............7-18TOOLS - DIESEL FUEL SYSTEM,
SPECIAL...........................14-63
TOOLS - FRONT AXLE, SPECIAL..........3-27
TOOLS - FUEL SYSTEM, SPECIAL . . . 14-35,14-4
TOOLS - HEADLAMP ALIGNMENT,
SPECIAL............................8L-4
TOOLS - INDEPENDENT FRONT
SUSPENSION, SPECIAL..................2-9
TOOLS - LINK/COIL SUSPENSION,
SPECIAL............................2-16
TOOLS - OVERHEAD CONSOLE SPECIAL
TOOL, SPECIAL......................8M-9
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-22
TOOLS - POWER STEERING PUMP,
SPECIAL...........................19-38
TOOLS - PROPELLER SHAFT, SPECIAL......3-6
TOOLS - RE TRANSMISSION, SPECIAL . . 21-146,
21-316
TOOLS - STEERING LINKAGE, SPECIAL . . . 19-41,
19-44
TOOLS - SUSPENSION-REAR, SPECIAL....2-27
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-9
TOOLS, AIRBAG SYSTEM - SPECIAL......8O-6
TOOLS, SPECIFICATIONS - SPECIAL.......8F-7
TOP COVER - INSTALLATION,
INSTRUMENT PANEL.................23-113
TOP COVER - REMOVAL, INSTRUMENT
PANEL............................23-113
TOW HOOK - INSTALLATION, FRONT.....13-10
TOW HOOK - REMOVAL, FRONT.........13-10
TOWING - STANDARD PROCEDURE.......0-10
TRACK - DESCRIPTION, POWER SEAT....8N-21
TRACK - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-22
TRACK - INSTALLATION, EASY ENTRY
SEAT .............................23-143
TRACK - INSTALLATION, POWER SEAT . . . 8N-22
TRACK - INSTALLATION, SEAT.........23-141
TRACK - OPERATION, POWER SEAT.....8N-22
TRACK - REMOVAL, EASY ENTRY SEAT . . 23-143
TRACK - REMOVAL, POWER SEAT.......8N-22
TRACK - REMOVAL, SEAT.............23-141
TRACK - SPLIT BENCH - INSTALLATION,
SEAT .............................23-142
TRACK - SPLIT BENCH - REMOVAL,
SEAT .............................23-142
TRACK ADJUSTER - INSTALLATION,
SEAT .............................23-143
TRACK ADJUSTER - REMOVAL, SEAT....23-143
TRACK BAR - DIAGNOSIS AND TESTING . . . 2-24
TRACK BAR - INSTALLATION............2-24
TRACK BAR - REMOVAL................2-24
TRAC-LOK - ASSEMBLY, DIFFERENTIAL . . . 3-129,
3-70
TRAC-LOK - DISASSEMBLY,
DIFFERENTIAL...................3-128,3-68
TRAC-LOKT- DIAGNOSIS AND TESTING . . 3-128,
3-67
TRAILER HITCH - INSTALLATION........13-11
TRAILER HITCH - REMOVAL............13-11
TRANS. - INSTALLATION, DIESEL WITH
AUTO..........................8P-12,8P-6
TRANS. - REMOVAL, DIESEL WITH AUTO
. . 8P-5,
8P-9
TRANS COOLER - 5.9L - DESCRIPTION
....7-78
TRANS COOLER - 5.9L - OPERATION
......7-78
TRANS COOLER - 5.9L DIESEL -
DESCRIPTION
........................7-84
TRANS COOLER - 5.9L DIESEL -
OPERATION
..........................7-84
TRANS COOLER - 8.0L - DESCRIPTION
....7-81
TRANS COOLER - 8.0L - OPERATION
......7-81
TRANS OVERTEMP INDICATOR -
DESCRIPTION
.......................8J-31
TRANS OVERTEMP INDICATOR -
OPERATION
.........................8J-31
TRANSFER CASE - DIAGNOSIS AND
TESTING
....................21-431,21-467
TRANSFER CASE - NV241 -
DESCRIPTION
.........................0-5
TRANSFER CASE - NV241HD -
ASSEMBLY
.........................21-480
TRANSFER CASE - NV241HD -
CLEANING
.........................21-476TRANSFER CASE - NV241HD -
DESCRIPTION......................21-465
TRANSFER CASE - NV241HD -
DISASSEMBLY......................21-469
TRANSFER CASE - NV241HD -
INSPECTION.......................21-476
TRANSFER CASE - NV241HD -
INSTALLATION......................21-494
TRANSFER CASE - NV241HD -
OPERATION........................21-467
TRANSFER CASE - NV241HD - REMOVAL . 21-469
TRANSFER CASE - NV241LD -
ASSEMBLY.........................21-445
TRANSFER CASE - NV241LD - CLEANING . 21-441
TRANSFER CASE - NV241LD -
DESCRIPTION......................21-430
TRANSFER CASE - NV241LD -
DISASSEMBLY......................21-432
TRANSFER CASE - NV241LD -
INSPECTION.......................21-442
TRANSFER CASE - NV241LD -
INSTALLATION......................21-458
TRANSFER CASE - NV241LD -
OPERATION........................21-430
TRANSFER CASE - NV241LD - REMOVAL . 21-432
TRANSFER CASE, NV241HD...........21-495
TRANSFER CASE, NV241LD...........21-459
TRANSFER CASE SKID PLATE -
INSTALLATION.......................13-11
TRANSFER CASE SKID PLATE -
REMOVAL..........................13-11
TRANSFER CASE, SPECIFICATIONS . 21-458,21-495
TRANSFER PUMP - DESCRIPTION, FUEL . . 14-83
TRANSFER PUMP - INSTALLATION, FUEL . 14-87
TRANSFER PUMP - OPERATION, FUEL....14-83
TRANSFER PUMP - REMOVAL, FUEL.....14-86
TRANSFER PUMP PRESSURE -
DIAGNOSIS AND TESTING, FUEL........14-84
TRANSMISSION - 46RE - DESCRIPTION,
AUTOMATIC.........................21-89
TRANSMISSION - 46RE - OPERATION,
AUTOMATIC.........................21-91
TRANSMISSION - 47RE - DESCRIPTION,
AUTOMATIC........................21-261
TRANSMISSION - 47RE - OPERATION,
AUTOMATIC........................21-263
TRANSMISSION - DESCRIPTION,
MANUAL.............................0-5
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC...........21-268,21-96
TRANSMISSION - INSTALLATION, SHIFT
BOOT - MANUAL....................23-122
TRANSMISSION - REMOVAL, SHIFT
BOOT - MANUAL....................23-122
TRANSMISSION CLUTCH AND BAND
OPERATION - DIAGNOSIS AND
TESTING, AIR TESTING.........21-100,21-272
TRANSMISSION FILL - STANDARD
PROCEDURE
.................21-160,21-330
TRANSMISSION FLUID - DESCRIPTION,
AUTOMATIC
...........................0-6
TRANSMISSION FLUID - OPERATION,
AUTOMATIC
...........................0-6
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITH
RADIATOR IN-TANK
...........7-78,7-82,7-84
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITHOUT
RADIATOR IN-TANK
...........7-79,7-82,7-85
TRANSMISSION, SPECIAL TOOLS - RE
. . 21-146,
21-316
TRANSMISSION, SPECIFICATIONS
......21-144,
21-314
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION
...............21-218,21-390
TRANSMISSION TEMPERATURE SENSOR
- OPERATION
.................21-218,21-390
TRANSMISSION THROTTLE VALVE
CABLE - ADJUSTMENTS
........21-210,21-382
TRANSMITTER - DESCRIPTION, REMOTE
KEYLESS ENTRY
......................8N-7
TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS ENTRY
......8N-8
TRANSMITTER - OPERATION, REMOTE
KEYLESS ENTRY
......................8N-8
32 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page