ECU DODGE RAM SRT-10 2006 Service Repair Manual

INSTALLATION
1. Install the window regulator (4) through the opening
in the door (2).
2. Engage the two regulator bolts (6) to the door.
3. Install the two bolt (5) that secure the window reg-
ulator to the door and tighten all four regulator bolts
to 10 Nꞏm (89 in. lbs.).
4. Position the regulator stabilizer (1) into the door
and install the two nuts (3). Tighten the nuts to 10
Nꞏm (89 in. lbs.).
5. Raise the window regulator (2) to the position
shown and remove the manual window crank.
6. Support the window glass and remove the wooden
wedge or equivalent.
7. Position the window glass to the window regulator
and install the two nuts (1) thought the two sight
windows (3 and 4). Tighten the nuts to 10 Nꞏm (89
in. lbs.).
8. Install the waterdam (Refer to 23 - BODY/DOOR -
FRONT/WATERDAM - INSTALLATION).
9. Install the inner belt molding (Refer to 23 - BODY/
WEATHERSTRIP/SEALS/FRONT DOOR INNER
BELT WEATHERSTRIP - INSTALLATION).

DOOR
REMOVAL
1. Disconnect and isolate the negative battery cable.
2. Disconnect the door wire harness connector (5)
from the body wire harness (8).
3. Using a grease pencil or equivalent, mark the loca-
tion of the door hinges (2 and 7) on the door (4).
NOTE: The epoxy bonded washers do not need to
be separated from the hinges. If the washers are
removed,thedoormayneedtobere-adjusted.
4. Support the door with a suitable lifting device and
remove the two nuts (1) and two bolts (9) that
secure the door to the hinges.
5. Carefully remove the door from the hinges.
6. If required, remove the two studs (3 and 6) from
the door.
INSTALLATION
1. If removed, install the two studs (3 and 6) into the
door (4).
2. Carefully position the door onto the hinges (2 and
7) and support the door with a suitable lifting
device.
NOTE: If the epoxy bonded washers are separated
from the hinges, the door may need to be
adjusted.
3. If removed, install the epoxy bonded washers.
4. Loosely install the two nuts (1) and the two bolts
(9) that secure the door to the hinges.
5. Align the door to the hinges using the reference
marks made during the removal procedure and
tighten the nuts and bolts to 28 Nꞏm (21 ft. lbs.).
6. Connect the door wire harness (5) to the body wire
harness (8).
7. Reconnect the negative battery cable.
8. If necessary, adjust the door (Refer to 23 - BODY/
DOORS - REAR/DOOR - ADJUSTMENTS).

DOOR GLASS
REMOVAL
NOTE: Quad Cab model shown, Mega Cab models
are similar.
1. Remove the inner belt molding (Refer to 23 -
BODY/WEATHERSTRIP/SEALS/REAR DOOR
INNER BELT MOLDING - REMOVAL).
2. Remove the waterdam (Refer to 23 - BODY/
DOORS - REAR/WATERDAM - REMOVAL).
3. Install the manual window crank or reconnect the
electric window switch to the door wire harness
(depending on application) and raise the door glass
to the position shown.
4. Remove the two nuts (1) that secure the door glass
(2) to the window regulator (3) through the speaker
opening (5) and the sight window (4) and disen-
gage the door glass from the regulator.
5. Remove the two bolts (1) that secure the front
glass run channel (2) to the door and remove the
run channel through the door panel opening.
6. Disengage the door glass from the window regula-
tor and lower the glass into the door.
7. Carefully rotate the door glass within the door and
remove the glass from the window opening.

INSTALLATION
1. Carefully lower the door glass into the door through
the window opening.
2. Rotate the door glass into position and engage it to
the window regulator.
3. Position the front glass run channel (1) into the
door through the door panel opening.
4. Install the two bolts (1) that secure the front glass
run channel to the door. Tighten the bolts to 10
Nꞏm (89 in. lbs.).
NOTE: Quad Cab model shown, Mega Cab models
are similar.
5. Install the two nuts (1) that secure the door glass
(2) to the window regulator (3) through the sight
window (4) and the speaker opening (5). Tighten
thenutsto10Nꞏm(89in.lbs.).
6. Lower the door glass into the door and remove the
manual window crank or disconnect the electric
window switch from the door wire harness
(depending on application).
7. Install the waterdam (Refer to 23 - BODY/DOORS
- REAR/WATERDAM - INSTALLATION).
8. Install the inner belt molding (Refer to 23 - BODY/
WEATHERSTRIP/SEALS/REAR DOOR INNER
BELT MOLDING - INSTALLATION).

EXTERIOR HANDLE
REMOVAL
1. Remove the front glass run channel (Refer to 23 -
BODY/DOORS - REAR/GLASS RUN CHANNEL -
REMOVAL).
2. Disconnect the actuator rod (1) from the exterior
door handle (2).
3. Remove the two nuts (3) that secure the exterior
door handle to the door and remove the handle.
INSTALLATION
1. Position the exterior handle (2) into the door.
2. Install the two nuts (3) that secure the exterior han-
dle to the door. Tighten the nuts to 10 Nꞏm (89 in.
lbs.).
3. Connect the actuator rod (1) to the exterior handle.
4. Install the front glass run channel (Refer to 23 -
BODY/DOORS - REAR/GLASS RUN CHANNEL -
INSTALLATION).

GLASS RUN CHANNEL
REMOVAL
FRONT
1. Raise the window glass to the full up position and
remove the window regulator (Refer to 23 - BODY/
DOORS - REAR/WINDOW REGULATOR -
REMOVAL).
2. Remove the two bolts (1) that secure the front
glass run channel (2) to the door and remove the
run channel through the door panel opening.
3. If required, remove the weatherstrip from the front
glass run channel.
Mega Cab Models
1. Raise the window glass to the full up position and
remove the window regulator (Refer to 23 - BODY/
DOORS - REAR/WINDOW REGULATOR -
REMOVAL).
2. Remove the two bolts (1 & 3) that secure the front
glass run channel (2) to the door and remove the
run channel through the door panel opening.
3. If required, remove the weatherstrip from the front
glass run channel.

REAR
1. Raise the window glass to the full up position and
remove the window regulator (Refer to 23 - BODY/
DOORS - REAR/WINDOW REGULATOR -
REMOVAL).
2. Remove the two bolts (2) that secure the rear glass
run channel (1) to the door and remove the run
channel through the door panel opening.
3. If required, remove the weatherstrip from the rear
glass run channel.
INSTALLATION
FRONT
1. If removed, install the weatherstrip onto the front
glass run channel (2).
2. Position the front glass run channel into the door
through the door panel opening.
3. Install the two bolts (1) that secure the front glass
run channel to the door. Tighten the bolts to 10
Nꞏm (89 in. lbs.).
4. Install the window regulator and verify correct win-
dow operation (Refer to 23 - BODY/DOORS -
REAR/WINDOW REGULATOR - INSTALLATION).

Mega Cab Models
1. If removed, install the weatherstrip onto the front
glass run channel (2).
2. Position the front glass run channel into the door
through the door panel opening.
3. Install the two bolts (1 & 3) that secure the front
glass run channel to the door. Tighten the bolts to
10 Nꞏm (89 in. lbs.).
4. Install the window regulator and verify correct win-
dow operation (Refer to 23 - BODY/DOORS -
REAR/WINDOW REGULATOR - INSTALLATION).
REAR
1. If removed, install the weatherstrip onto the rear
glass run channel (1).
2. Position the rear glass run channel into the door
through the door panel opening.
3. Install the two bolts (2) that secure the rear glass
run channel to the door. Tighten the bolts to 10
Nꞏm (89 in. lbs.).
4. Install the window regulator and verify correct win-
dow operation (Refer to 23 - BODY/DOORS -
REAR/WINDOW REGULATOR - INSTALLATION).

INTERIOR HANDLE ACTUATOR
REMOVAL
1. Remove the door trim panel (Refer to 23 - BODY/
DOORS - REAR/TRIM PANEL - REMOVAL).
2. Position the waterdam out of the way and discon-
nect the actuator rod (2) from interior door handle
actuator (3).
3. Remove the two bolts (1) that secure the interior
door handle actuator to the door and remove the
actuator.
INSTALLATION
1. Position the interior door handle actuator (3) onto
the door.
2. Install the two bolts (1) that secure the interior door
handle actuator to the door. Tighten the bolts to 10
Nꞏm (89 in. lbs.).
3. Connect the actuator rod (2) to the interior door
handle actuator.
4. Reposition the waterdam and install the door trim
panel (Refer to 23 - BODY/DOORS - REAR/TRIM
PANEL - INSTALLATION).

LATCH
REMOVAL
1. Raise the window to the full up position and
remove the door trim panel (Refer to 23 - BODY/
DOORS - REAR/TRIM PANEL - REMOVAL).
2. Position the waterdam out of the way and discon-
nect the actuator rod (1) from the interior door han-
dle actuator (2) and the door latch (5) and remove
the rod.
3. Disconnect the two actuator rods (3 and 4) from
the door latch.
4. Disconnect the door wire harness connector (2)
from the door latch (3).
5. Remove the three bolts (4) that secure the door
latch to the door (1) and remove the latch.