ECU DODGE RAM SRT-10 2006 Service Repair Manual

CONNECTOR/GROUND/SPLICE LOCATION - DESCRIPTION).
5. If removed, install the tailgate (Refer to 23 - BODY/TAILGATE/TAILGATE- INSTALLATION).
6. If removed, install the rear bumper (Refer to 13 - FRAME & BUMPERS/BUMPERS/REAR BUMPER - INSTAL-
LATION).
7. If removed, install the fuel filler door (Refer to 23 -
BODY/EXTERIOR/FUEL FILL DOOR - INSTALLA-
TION).
8. Position the fuel filler (2) to the cargo box (3).
9. Install the screws (1) that secure the fuel filler to
the cargo box. Tighten the screws to 2.2 Nꞏm (20
in. lbs.).

CARGO BOX - TIE DOWN
REMOVAL
1. Remove the two bolts (1) that secure each cargo
box tie down (2) to the cargo bed and remove the
cleats as necessary.
INSTALLATION
1. Position the cargo box tie downs (2) to the cargo
box as necessary.
2. Install the two bolts (1) that secure each cargo box
tie down to the cargo box. Tighten the bolts to 34
Nꞏm (25 ft. lbs.).

COWL GRILLE
REMOVAL
1. Remove the wiper arms (Refer to 8 - ELECTRI-
CAL/WIPERS/WASHERS/WIPER ARMS -
REMOVAL).
2. Disconnect the cowl plenum washer hose from the
washer supply hose at the molded plastic in-line fit-
ting (Refer to 8 - ELECTRICAL/WIPERS/WASH-
ERS/WASHER HOSES/TUBES - DESCRIPTION).
3. Remove the cowl weather seal from the front of the
dash panel and the cowl grille (2).
4. Remove the six push pin fasteners (1) that secure
the front of the cowl grille to the dash panel.
5. Remove the two screws (3) that secure the rear
corners of the cowl grille to the dash panel and
remove the grille.
6. If necessary, remove the washer nozzles and the
cowl plenum washer hose from the cowl grille
(Refer to 8 - ELECTRICAL/WIPERS/WASHERS/WASHER NOZZLE - REMOVAL).
INSTALLATION
1. If removed, install the washer nozzles and the cowl
plenum washer hose onto the cowl grille (2) (Refer
to 8 - ELECTRICAL/WIPERS/WASHERS/WASHER
NOZZLE - INSTALLATION).
2. Position the cowl grille onto the dash panel.
3. Install the two screws (3) and the six push-pin fas-
teners (1) that secure the cowl grille to the dash
panel.
4. Install the cowl weather seal onto the front of the
dash panel and the cowl grille.
5. Connect the cowl plenum washer hose to the
washer supply hose at the molded plastic in-line fit-
ting (Refer to 8 - ELECTRICAL/WIPERS/WASH-
ERS/WASHER HOSES/TUBES - DESCRIPTION).
6. Install the wiper arms (Refer to 8 - ELECTRICAL/
WIPERS/WASHERS/WIPER ARMS - INSTALLA-
TION).

FRONT FENDER
REMOVAL
1. Remove the radio antenna (Refer to 8 - ELECTRI-
CAL/AUDIO/ANTENNA BODY & CABLE -
REMOVAL).
2. Remove the battery tray (depending on fender
beingserviced)(Referto8-ELECTRICAL/BAT-
TERY SYSTEM/TRAY - REMOVAL).
3. Remove the cowl grille (Refer to 23 - BODY/EXTE-
RIOR/COWL GRILLE - REMOVAL).
4. Remove the headlamp unit (Refer to 8 - ELECTRI-
CAL/LAMPS/LIGHTING - EXTERIOR/HEADLAMP
UNIT - REMOVAL).
5. Remove the wheelhouse splash shield (Refer to 23
- BODY/EXTERIOR/FRONT WHEELHOUSE
SPLASH SHIELD - REMOVAL).
6. Remove the bolts (1, 2, 3, 5 and 6) that secure the
front fender (7) to body.
7. Carefully remove the front fender from the body
and remove the plastic inserts (4), if required.
INSTALLATION
1. If required, install new plastic inserts (4) into the
front fender (7).
2. Position the front fender onto the body and loosely
install all fender retaining bolts.
3. Align the front fender and add shims, if required
(Refer to 23 - BODY/BODY STRUCTURE/GAP
AND FLUSH - SPECIFICATIONS).
4. Tighten the bolts (2 and 6) to 9 Nꞏm (80 in. lbs.).
5. Tighten the bolts (1, 3 and 5) to 12.5 Nꞏm (9 ft.
lbs.).
6. Install the wheelhouse splash shield (Refer to 23 -
BODY/EXTERIOR/FRONT WHEELHOUSE
SPLASH SHIELD - INSTALLATION).
7. Install the headlamp unit (Refer to 8 - ELECTRI-
CAL/LAMPS/LIGHTING - EXTERIOR/HEADLAMP
UNIT - INSTALLATION).
8. Install the cowl grille (Refer to 23 - BODY/EXTERI-
OR/COWL GRILLE - INSTALLATION).
9. Install the battery tray, if required (Refer to 8 - ELECTRICAL/BATTERY SYSTEM/TRAY - INSTALLATION).
10. Install the antenna (Refer to 8 - ELECTRICAL/AUDIO/ANTENNA BODY & CABLE - INSTALLATION).

FUEL FILL DOOR
REMOVAL
1. Open the fuel filler door (1).
2. Remove the two bolts (2) that secure the fuel filler
door to the cargo box and remove the door.
INSTALLATION
1. Position and align the fuel filler door (1) to the
cargo box.
2. Install the two bolts (2) that secure the fuel filler
door to the cargo box. Tighten the bolts to 9 Nꞏm
(80 in. lbs.).

GRILLE
REMOVAL
1. Open the hood (2) and remove the six screws (5)
that secure the grille (3) to the grille frame (4).
2. Remove the six nuts (1) that secure the grille to the
hood and remove the grille.
3. If required, remove the grille frame from the hood
(Refer to 23 - BODY/EXTERIOR/GRILLE FRAME -
REMOVAL).
INSTALLATION
1. If removed, install the grille frame (4) (Refer to 23 -
BODY/EXTERIOR/GRILLE FRAME - INSTALLA-
TION).
2. Position and align the grille (3) onto the hood (2)
3. Install the six nuts (1) that secure the grille to the
hood. Tighten the nuts to 5 Nꞏm (44 in. lbs.).
4. Install the six screws (5) that secure the grille to
the grille frame. Tighten the screws to 2.2 Nꞏm (20
in. lbs.).

GRILLE FRAME
REMOVAL
1. Remove the grille (Refer to 23 - BODY/EXTERIOR/
GRILLE - REMOVAL).
2. Remove the six screws (3) that secure the grille
frame (2) to the hood (1) and remove the frame.
INSTALLATION
1. Position the grille frame (2) onto the hood (1).
2. Install the six screws (3) that secure the grille
frame to the hood. Tighten the screws to 5 Nꞏm (44
in. lbs.).
3. Install the grille (Refer to 23 - BODY/EXTERIOR/
GRILLE - INSTALLATION).

REAR FENDER-QUAD CAB MODELS
REMOVAL
1. Disconnect and isolate the negative battery cable.
2. Remove the tail lamp unit (Refer to 8 - ELECTRI-
CAL/LAMPS/LIGHTING - EXTERIOR/TAIL LAMP
UNIT - REMOVAL).
3. Remove the rear wheelhouse splash shield (Refer
to 23 - BODY/EXTERIOR/REAR WHEELHOUSE
SPLASH SHIELD - REMOVAL).
4. Remove the two marker lamp units from the rear
fender (Refer to 8 - ELECTRICAL/LAMPS/LIGHT-
ING - EXTERIOR/MARKER LAMP UNIT -
REMOVAL).
5. Remove the two nuts (2) that secure the rear
fender to the cargo box near the tail lamp opening
(1).
6. Raise and support the vehicle.
7. Remove the two nuts (1) that secure the rear
fender to the rear of the cargo box inner panel (2).
8. Remove the four bolts that secure the bottom
edges of the rear fender to the cargo box.

9. Remove the four nuts (2) secure the front of the
rear fender to the cargo box inner panel (1)
10. Loosen the three bolts (3) on each of the two
fender support brackets (1) located on the cargo
box outer panel (2).
CAUTION: Prior to removing the rear fenders,
mask off the surrounding cargo box areas to avoid
damage to the cargo box painted surfaces.
11. Lift the rear fender straight up and off of the two
support brackets and remove the fender.
INSTALLATION
CAUTION: Prior to installing the rear fenders,
mask off the surrounding areas to avoid damage
to the cargo box painted surfaces.
1. Carefully position the rear fender onto the three
bolts (3) on each of the two support brackets (1)
located on the cargo box outer panel (2).

2. Install the four nuts (2) that secure the front of the
rear fender to the cargo box inner panel (1).
Tightenthenutsto7Nꞏm(60in.lbs.).
3. Install the two nuts (1) that secure the rear fender
to the rear of the cargo box inner panel (2). Tighten
thenutsto7Nꞏm(60in.lbs.).
4. Install the four bolts that secure the bottom edges
of the rear fender to the cargo box. Tighten the
bolts to 7 Nꞏm (60 in. lbs.).
5. Tighten the three bolts on each of the two support
brackets to 11 Nꞏm (8 ft. lbs.).